CAM 6.0 - FMS engine may not be responding

Hi,
after installation CAM 6.0 on Suse Linux Enterprise Server 10 SP1 English, I can login to webinterface start CAM and everything works fine.
If I restart SLES, login to webinterface is possible, however after starting CAM I get the following error:
"The CAM FMS engine may not be responding. Please contact your Technical Support Representative for assistance."
Uninstalling and installing solves the problem only temporarily (until next restart).
Any ideas?
Matthias

Hi,
I have the same problem on Solaris 10 (SPARC).
Which process restart this service when we shuttding down.
I try to start fmservice in console mode for monitoring, but it was already start:
root # /opt/SUNWsefms/sbin/fmservice.sh status
Sun StorageTek(TM) Fault Management Service is running (24464).
root # /opt/SUNWsefms/sbin/fmservice.sh stop; /opt/SUNWsefms/sbin/fmservice.sh console
Stopping Sun StorageTek(TM) Fault Management Service...
Stopped Sun StorageTek(TM) Fault Management Service.
Running Sun StorageTek(TM) Fault Management Service...
Sun StorageTek(TM) Fault Management Service is already running.
root # /opt/SUNWsefms/sbin/fmservice.sh status
Sun StorageTek(TM) Fault Management Service is running (1038).
root #
I try to stop "fmd", but the problem still the same.
Need help.
Thank you

Similar Messages

Errors in the high-level relational engine. The data source view does not contain a definition for the table or view. The Source property may not have been set.

Hi All,
I have a cube in which i'm using the TIME DIM that i created in the warehouse. But now i wanted a new measure in the cube which is Average over time and when i wanted to created the new measure i got a message that no time dim was defined, so i created a
new time dimension in the SSAS using wizard. But when i tried to process the new time dimension i'm getting the follwoing error message
"Errors in the high-level relational engine. The data source view does not contain a definition for "SSASTIMEDIM" the table or view. The Source property may not have been set."
Can anyone please tell me why i cannot create a new measure average over the time using my time dimension? Also what am i doing wrong with the SSASTIMEDIM, that i'm getting the error.
Thanks

Hi PMunshi,
According to your description, you get the above error when processing the time dimension. Right?
In this scenario, since you have updated the DSV, it should have no problem on the table existence. One possibility is that table has been specified for tracking in the notifications for proactive caching, but isn't available any more for some
reason. Please change the setting in Proactive Caching into "MOLAP".
Reference:
How To Implement Proactive Caching in SQL Server Analysis Services SSAS
If you have any question, please feel free to ask.
Best Regards,
Simon Hou
TechNet Community Support

Two previous questions may not have been as clear as I would have liked. I recently upgraded my MacBook 2008 (10.5.8) to Snow Leopard (10.6.8). With the updates came iTunes 11.1.1 and Quicktime 7.6.6. I am still using Garageband 2008 and iPhoto 2008. When

Two previous questions may not have been as clear as I would have liked. I recently upgraded my MacBook 2008 (10.5.8) to Snow Leopard (10.6.8). With the updates came iTunes 11.1.1 and Quicktime 7.6.6. I am still using Garageband 2008 and iPhoto 2008. When I create music in Garageband I usually adjust the volume and save it. Even now when I share the Garageband created files with iTunes 11.1.1, the volime I previously set in Garageband is retained. However, when I use the music to create a slide show in iPhoto 2008 and export to Quicktime 7.6.6, the volume level I previously set is lost and seems to default to a low level. The problem seems to be either in the slide show export from iPhoto 2008 to Quicktime 7.6.6 or in Quicktime itself. Is there a work around, so that I can retain the volume level I had previously set in Garageband, a volume level that seems to transfer without problem to the new iTunes. But then iPhoto 2008 (slide show) possibly or Quicktime 7.6.6 do not cooperate. Before I did the upgrade to Snow Leopard, the new iTunes and Quicktime I had no problems with the set volume being retained in the old Quicktime. The reason I need control over the volume is that all these music files are uploaded to YouTube.

Two previous questions may not have been as clear as I would have liked. I recently upgraded my MacBook 2008 (10.5.8) to Snow Leopard (10.6.8). With the updates came iTunes 11.1.1 and Quicktime 7.6.6. I am still using Garageband 2008 and iPhoto 2008. When I create music in Garageband I usually adjust the volume and save it. Even now when I share the Garageband created files with iTunes 11.1.1, the volime I previously set in Garageband is retained. However, when I use the music to create a slide show in iPhoto 2008 and export to Quicktime 7.6.6, the volume level I previously set is lost and seems to default to a low level. The problem seems to be either in the slide show export from iPhoto 2008 to Quicktime 7.6.6 or in Quicktime itself. Is there a work around, so that I can retain the volume level I had previously set in Garageband, a volume level that seems to transfer without problem to the new iTunes. But then iPhoto 2008 (slide show) possibly or Quicktime 7.6.6 do not cooperate. Before I did the upgrade to Snow Leopard, the new iTunes and Quicktime I had no problems with the set volume being retained in the old Quicktime. The reason I need control over the volume is that all these music files are uploaded to YouTube.

HT4623 Why do my iPhone cords for my 5 say it is not certified and may not work with this device? It's the same cord that came with my phone. The only difference is the iOS7 update.

Why do my iPhone cords for my 5 say it is not certified and may not work with this device? It's the same cord that came with my phone. The only difference is the iOS7 update.
Maps took me to the completely wrong side of town for a long standing business in town.

Hello margmcarlson,
Thanks for using Apple Support Communities.
For more information on this, take a look at:
Troubleshooting iPhone, iPad, and iPod touch accessories
http://support.apple.com/kb/TS2634
Restore iPhone, iPad, or iPod touch to its factory default state. You should rarely need to use this step with an accessory issue.
Best of luck,
Mario

I just got a new ipod 5 and when I plugged in the charging cord that came with it, it says it is not supported, and may not charge. It worked the first few times, but now it won't charge at all.

I just got a new ipod 5 and when I plugged in the charging cord that came with it, it says it is not supported, and may not charge. It worked the first few times, but now it won't charge at all.

- See:
iPod touch: Hardware troubleshooting
iPhone and iPod touch: Charging the battery
- Try another cable. Some 5G iPods were shipped with Lightning cable that were either initially defective or failed after short use.
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store. The cable as well as the iPod, is covered by the warranty.
Apple Retail Store - Genius Bar

Photo will not upload my pictures from the same camera that always worked in IPhoto. Says "could not be imported (may be unrecognized file type or files may not contain valid data). So how do I do it?

Photo will not upload new photos from same camera that always worked in IPhoto. Says "could not be uploaded )may be unrecognized file type or files may not contain valid data). Help!

Try image capture or a card reader - after the photos are safely on your Mac then use the camera's format command to reformat the memory card
LN

You may not need to install the Run Time Engine...

I know this has been mentioned before, but after a long search of the archives, I couldn't find the right person to give credit to - sorry!
If you have a simple exe, you may not need to install the runtime engine on the target machine at all - all you need to do is include some of the engine's files with the exe for it to work. Try it out: copy the following files & folders into the folder containing your exe:
..\National Instruments\shared\nicontdt.dll
..\National Instruments\shared\nicont.dll
..\National Instruments\shared\LabVIEW Run-Time\your_version\everything (including all sub-directories)
so, using 6.1 as an example, you exe's directory would like something like:
..\AppDirectory\MyApp.exe
..\AppDirectory\MyApp.ini
..\AppDirectory\My_Apps_DLLs,if_any
..\AppDirectory\nicontdt.dll
..\AppDirectory\nicont.dll
..\AppDirectory\lvapp.rsc
..\AppDirectory\lvjpeg.dll
..\AppDirectory\lvpng.dll
..\AppDirectory\lvrt.dll
..\AppDirectory\mesa.dll
..\AppDirectory\serpdrv
..\AppDirectory\models\heaps_of_stuff_in_here
..\AppDirectory\errors\more_stuff_in_here
..\AppDirectory\script\and_some_bits_in_here_too
Take all of this data to a machine without LabVIEW or the runtime installed, and try to run the exe - all going well, it will execute without any problems. This exe distribution method can be really useful, especially when distributing autorun presentations on CD-ROMs.
* DISCLAIMER: as far as I am aware, this method is NOT authorised or supported by NI - use it at your own risk!
cheers,
Christopher
PS: I'd like your feedback: please give this posting a rating
Christopher G. Relf
[email protected]
Int'l Voicemail & Fax: +61 2 8080 8132
Aust Voicemail & Fax: (02) 8080 8132
EULA
1) This is a private email, and although the views expressed within it may not be purely my own, unless specifically referenced I do not suggest they are necessarily associated with anyone else including, but
not limited to, my employer(s).
2) This email has NOT been scanned for virii - attached file(s), if any, are provided as is. By copying, detaching and/or opening attached files, you agree to indemnify the sender of such responsibility.
3) Because e-mail can be altered electronically, the integrity of this communication cannot be guaranteed.
Copyright © 2004-2015 Christopher G. Relf. Some Rights Reserved. This posting is licensed under a Creative Commons Attribution 2.5 License.

Yes, this method is not supported. However, this method is good if you wish to write your own installer for a LabVIEW Application. (Note: The method above does not install DataSocket, NI-Reports, or any of the 3D Graph controls.)
I would still suggest running the LabVIEW Run-time Engine installer so that more than one application can use it.
Randy Hoskin
Applications Engineer
National Instruments
http://www.ni.com/ask

I've had my iphone 5s since march 2014 and I've been using the same charger it came with. for the last two weeks ive been getting a message saying the accessory may not support the device. how is that possible?

How come I keep getting a message saying that the accessory may not support the device? I've been using the same charger that came in the box with the phone. Now it doesn't charge at all.

Then take the cable, the plug and your iPhone to an Apple Store genius bar it is still under the 12 month warranty

Using IMOVIE '08 to import from DV camera to 'BUSLINK' external hard drive( formatted for MAC ) but no success and kept getting this message: The import was canceled. You may not have permission to write to /Volumes/BUSLINK/iMovie Events.localized. Thanx

Using IMOVIE '08 to import from DV camera to 'BUSLINK' external hard drive( formatted for MAC ) but no success and kept getting this message: The import was canceled. You may not have permission to write to /Volumes/BUSLINK/iMovie Events.localized. Thanx in advance!

I finally got a representative that was able to help me, she had me go to Get Info, by right clicking iMovie from the finder, and I had to click on Sharing & Permissions>Everyone>Read & Write

Since I downloaded the upgraded software, my charger that came with my phone says "this cable or accessory is not certified and may not work reliably with this iphone" It worked before but now it doesn't...I don't think I should have to buy a new one...

since I upgraded to the new operating system my charger no longer works...
It says"this cable or accessory is not certified and may not work reliably with this iPhone"

Try checking your cable socket/lightning cable for dirt, grime, pocket lint, etc. I could not find the solution to this issue myself and after much searching I found someone stating that cleaning this out helped them immensely.
After taking a wooden toothpick (making sure the phone was OFF first) and gently clearing out the edges and inside of the lightning socket this went away.) It is worth noting that I had a significant amount of dust or lint buildup along the edge rails which I think was causing the iphone to believe it was plugged into something when it was not.
Try it and see, ensure you are very careful and do not use any conductive tools to clean the area in question. Compressed air also does wonders here.

This accessory may not be supported message started a few days ago. Now, I get the message every time I plug in and my phone won't charge!

Three days ago, my iPhone 4 started sporadically displaying this message when I plugged my authentic apple iPhone charger in: "This accessory may not be supported." I was dismissing it, until my battery was nearly dead and I finally realized that when the message would come up the charging would stop.
Somehow, last night, I got it to begin charging on my Macbook and although it stopped a few times, got it back to 95%.
Now, it happens every time I plug it in to charge and it WILL NOT charge.
Details:
I am using genuine apple chargers. The one that came with my iPhone and the one that came with my iPad.
I am using outlets that work.
I have tried charging on my Macbook and receive the same message.
I am on IOS 7.1.1
The battery seems to be draining faster than usual.
It seems like when the battery gets low enough (<5%), it will charge again, at least a little bit, without the message popping up?
I tried to make a genius bar appt. but the next one isn't until next Tuesday! Eek. I cannot afford a new phone right now, and I am really hoping there is a way to fix this. If there is anything I can do at home to isolate the problem, or reduce what could end up costing a lot I would greatly appreciate your help.

hi, try all what these guys say, as they make sense (my bet is on a slug of kebab guys ).
you list bits you have tried but don't say if you have tried a new lead?
i'm not being tricky, as an electronics engineer of some 40+ years who repairs consuls, iPhones, iPads etc. i have some experience of what gets overlooked. Some of the cheap after market leads aren't the best quality,and some darn right lethal, likely to catch fire while your asleep. you might have bought of them.
i find it tends only genuine Apple leads lock in, but there might be fakes of them to. either way worth a go. perhaps se if your family or mates have one.
Alan

Report engin is not working

Dear All
I have install Forms6i and Report6i on client machine and give exact path of server and also mention net 8 service and also give path of reports and forms. my form are running correct but my eports are not working and i notice when i run my report then report engin is not come on status bar, please let me know the solutions
Thanks in Advance
Regard

Hello,
The problem may be a PATH problem.
Start the reports server after having set the PATH :
set ORACLE_HOME=d:\oracle\ods1012
set PATH=%ORACLE_HOME%\jdk\jre\bin\classic;%ORACLE_HOME%\jdk\jre\bin;%ORACLE_HOME%\jdk\jre\bin\client;%ORACLE_HOME%\jlib;%ORACLE_HOME%\bin;%ORACLE_HOME%\jdk\bin;%ORACLE_HOME%\jre\1.4.2\bin\client;%ORACLE_HOME%\jre\1.4.2\bin;
Regards

Reader XI, An Error Exists on this Page, Acrobat may not display

Hello,
I need some help please. The small business I work for as a contract employee uses Google Doc's, and we input our information into spreadsheets on a daily basis, from our home computers.
My home computer is XP Professional, and I am using Mozilla Firefox 36.0. I know we are using older computer programs, but until we can afford newer computers we have to use what we have.
Prior to today, when I printed off my spreadsheets in Google Doc's I had no problems, however tonight I just starting receiving this error message; An error exists on this page. Acrobat may not display the page correctly. Please contact the person who created the file.
I contacted my manager and had her send me a new spreadsheet, Invitation to Edit and input my information into the new spreadsheet.
I then go to my timesheet, and highlight all the rows that I would like to print, then I hit the print key, then I get the box that states, opening my timesheet which is a PDF which is an Adobe Acrobat Document, then I have this message, What should Firefox do with this file? I have it set to open with Adobe Reader (default) do this for files automatically like this.
The file downloads, however I have noticed that Adobe at times has a difficult time opening up right away and then I receive the error message that Adobe isn't responding and I end up closing the program out and restarting my computer.
This error message shows up just before the document begins to print and the document prints off with out any problems.
I even did a repair and that didn't help. My printer is a HP Color LaserJet 4500 and I've had no issues with Adobe prior to tonight.
Do I need to uninstall Adobe Reader & Re-install the program?
I can't send a copy of the file because it contains confidential material.
I've also posted this message on Adobe Acrobat, and have not received a response.
Please advise.
Thank you,

Hello,
Thank you for responding. Sorry that my message is so confusing.
In Google Doc's we are able to highlight/selected portions of a PDF to print.
In Mozilla Fox under Applications, Portable Format Document (PDF) Use Adobe Reader (default).
So when I go to print off my timesheet, after I have highlighted everything, I get this message: I've chosen to open my timesheet which is: Adobe Acrobat Document from https//docs.google.com. What should Firefox do with this file? Open with Adobe Reader (default).
Do this automatically for files like this from now on. I click on the OK and the file downloads as a PDF file in Adobe Reader. On Google Doc's I click on the print key then I am able to open up my printer menu. Its after I click on the print key that I receive this message.
So what do I do please?
Thank you,
Maureen A. Mumm
From: pwillener <[email protected]>
To: Maureen Mumm <[email protected]>
Sent: Friday, March 6, 2015 8:05 PM
Subject: Reader XI, An Error Exists on this Page, Acrobat may not display
Reader XI, An Error Exists on this Page, Acrobat may not display
created by pwillener in Adobe Reader - View the full discussion
Maureen Mumm wrote: I then go to my timesheet, and highlight all the rows that I would like to print, then I hit the print key, then I get the box that states, opening my timesheet which is a PDF which is an Adobe Acrobat Document, then I have this message, What should Firefox do with this file? I have it set to open with Adobe Reader (default) do this for files automatically like this.
This is very confusing to me; Adobe Reader does not have such a functionality (to print highlighted/selected portions of a PDF). Could it be that this is a functionality of Google Docs? Also I have never seen a message "What should Firefox do with this file?". If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7262026#7262026 and clicking ‘Correct’ below the answer Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page: Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7262026#7262026 To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following" Start a new discussion in Adobe Reader by email or at Adobe Community For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

'"Connection Failed" : The server "rrnas01" may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again' message

'"Connection Failed" : The server "rrnas01" may not exist or it is unavailable at this time. Check the server name or IP address, check your network connection, and then try again' message keeps displaying whenever I try to open any Adobe CS5 applications (except for Adobe Acrobat Pro). It displays until I click "OK" about 15-20 times or so and then will finally let my program open.
I have tried deleting files within my Library/Preferences folder and turning off/deleting login items within my system preferences as other forums suggested but nothing happened. Spending 3.5 hours on the phone with Adobe and completely uninstalling and then reinstalling the entire CS5 Master Collection didn't work either.
Also, it may be helpful to know that my programs worked fine for about three weeks then when we got internet and changed the password (the join, not the adminstrative password) with the wireless network "ScubaSteve" (which I've used with no problems at my old apartment) it started acting up. I have never seen "rrnas01" before so I don't know at all where it came from. I also installed the free 30 day trial of Suitcase Fusion 3 recently, but thinking that could also be the cause I have uninstalled it, and still no help.
Please help me! And please keep in mind I don't know all the computer lingo that a lot of the people in these forums seem to know. Thanks in advance for ny help you can give me.

It may not be possible .. there is a major bug between Mountain Lion and the TC where the TC disk goes off the radar of the computer.
Lion is also affected but not as badly.
7.6.4 seems worse than earlier firmware.. so back to 7.6.1 or 7.5.2 if that is possible.
Obviously that is not a solution for a later Gen5 TC.
Reset to factory after the firmware downgrade. .use all network names that are short, no spaces and pure alphanumeric.
If the TC is the main router set the dhcp to a very short lease time.. eg 30min.. and see how it goes, or try a longer lease like 99days.
I prefer the very short lease but response has been mixed.
Use ethernet not wireless.. ethernet is always more reliable and stable than wireless.
And last .. a nightly electric timer that powers off every night at midnight for 1min.. would not be the first device we have suggested a fix that amounts to beat the unit to the punch by forcing it to reboot since it is unstable.

My iPod touch 5th gen isn't charging and when I plug my working charger in that I've always used a message pops up that says "This accessory may not be supported". So can I send it in for a new one if I have a warranty?

For Christmas, my older sister got me a portable charger for my iPod. I'm not sure if it was capable with apple products, but it charged my iPod when I used it. My brother came upstairs and took my portable charger from me, so I went to go use my wall charger. The wall charger I have has always worked and it charges my mom's iPhone, so the problem I have isn't my charger. After I plugged my iPod in my charger, a message popped up saying "This accessory may not be supported". I was confused because this never has happened before, so I tried my portable charger after I got the message. The portable charger didn't charge my iPod anymore apparently after I tried my charger. All this happened the day after Christmas, so it's almost been a month without my iPod charging properly. My iPod does charge, but only when I plug it in halfway and am about to turn it all the way off. The only way I get it to charge is when I plug it in real fast as soon as I turn my iPod completely off. I've also restarted my iPod, cleaned out the charging area, asked people at stores that work with technology, and etc, so if someone could help me resolve this problem that would be legit because I use my iPod on a daily basis.

That message is usually due to a bad cable.
Not Charge
- See:
iPod touch: Hardware troubleshooting
iPhone and iPod touch: Charging the battery
If you can’t charge your iPhone, iPad, or iPod touch
- Try another cable. The cable for 5G iPod (lightning connector) seems to be more prone to failure than the older cable.
- If a 5G iPod
Iphone 5 lightning port charging problem - SOLUTION!
- Try another charging source
- Inspect the dock connector on the iPod for bent or missing contacts, foreign material, corroded contacts, broken, missing or cracked plastic.
- Make an appointment at the Genius Bar of an Apple store.
Apple Retail Store - Genius Bar
or send it in to Apple. See:
Service Answer Center - iPod

CAM 6.0 - FMS engine may not be responding

Similar Messages

Maybe you are looking for