Cambridge Soundworks or Creati

Just a thought, do you prefer speakers based on Cambridge Soundworks or Creative designed?
From what i hear, the Megaworks and the S750 are Cambridge and the Gigaworks G500 is one hundred percent Creative.

Well, actually it's none of those...
The subwoofer looks different, like this: http://www.terrabits.org/Files/P930000.JPG
The speaker look like the FPS1000 ones, like this: http://www.terrabits.org/Files/P9300002.JPG
But most importantly, the volumecontrol, and especially the conector that goes into the subwoofer, look like this:
http://www.terrabits.org/Files/P9300006.JPG
Hope that helps.
..Message Edited by Mohawk20 on 09-30-2007 09:39 PM

Similar Messages

  • Connecting Cambridge Soundworks speakers to a new Dell 4700

    New system: Dell 4700. Soundcard is a Soundblaster Live! 24 bit. Stereo outputs are confirmed to work because my headphones pick up sound (in the headphone jack, as well as the stereo outputs). Creative audio software.
    Old speakers: Cambridge Soundworks, 2 small cube speakers and a subwoofer with a dedicated power supply. About 3 years old. System worked like a charm (and still does) in my old computer.
    My new computer sound outputs are just fine. My old speakers work fine. But the two together aren't working. I've been troubleshooting all evening. Dell tech support was also clueless. Anyone able to offer some advice from the audio side of things?
    Thanks!

    Bmsavage,
    There are a couple things to check. First off make sure any headphones in the front of the computer are unplugged (this can disable the rear outputs).
    Now try connecting like this:
    1) Connect the speaker side of your volume control to the line in on the subwoofer.
    2) Connect the source side of your volume control to the Green Jack on the Live! 24bit
    3) Insure that the volume on the control is turned up and the speakers are powered up and test sound
    Jeremy

  • Dolby Digital AC-3 missing: Realtek ALC892 / Creative Cambridge SoundWorks DeskTop Theater 5.1

    Hi there,
    recently I purchased a new mainboard (ASUS Sabertooth X58, http://dlcdnet.asus.com/pub/ASUS/mb/...th_X58.pdfwith an internal soundchip ALC892 from Realtek. This mainbard has an internal S/PDIF-Connector which I connected to a coax cable for fitting the Dolby Digital AC-3 S/PDIF input of the Creative Cambridge SoundWorks DeskTop Theater 5.1 (model CSW3000, 998, http://download.cambridgesoundworks....nuals/DTT5.pdf
    As the SoundWorks has an internal Dolby decoder working it seems to be somewhat difficult to get the noise going. Simply connecting the cable does not work, neither tuning the Realtek sound driver. It seems that the Realtek driver is missing an option to stream directly to the DTT5.1.
    Is there any possibility to get the combination working?
    Best regards, Ingo Wolfmller

    I installed my old Audigy 2 and connected the Speakers. The digital output of that soundcard works. So the speakers are alright. But the AC-3 stream e.g. coming from an DVD delivers a steady crunching/crashing sound. Maybe a configuration problem although I fixed the output to Dolby Digital an 48 kHz.
    The internal Realtek still delivers nothing.

  • 5.1 with X-Fi and older Cambridge Soundworks speake

    I have an older Cambridge Soundworks Desktop Theater 5. DTT2500 Digital speaker system, and I just bought a SoundBlaster X-Fi Xtreme Gamer card for my Vista (32bit) computer.
    The speaker system has four inputs:
    Line In
    Rear In
    Dolby Digital (AC-3) S/PDIF
    Digital DIN
    I currently can only get 4. sound by using the two analog connections (Line and Rear). I used to have an Audigy NS, which was able to connect directly to the S/PDIF plug on my speaker system to provide 5. surround.
    How can I connect my X-Fi's Digital Out flexijack to my speaker system's digital inputs so I can get full 5. surround?
    Thanks for your time!

    I own those speakers and as someone else pointed out they're not true 5. speakers, they are only true for movies, not for games, even with the adapter, the center channel will not pick it up. I opted for another manufacturer speakers. When that came out, it was top of the line, high tech etc. But only really for movies, I have it hooked up to my DVD player now and that's all it's good for. And when I had it hooked up to my computer all I was ever able to get out of it was 4. with the spdf adapter and connection.

  • SB Live! 5.1 Digital card and Creative Cambridge Soundworks 200 Speak

    I have a SB Li've! 5. Digital card and a set of Creative Cambridge Soundworks 200 Speakers. The speakers consist of 4 satelites and sub woofer. My audio has been working flawlessly for several years until this weekend when I decided to reformat my dri've and re-install Windows XP Pro. I downloaded the dell drivers (card is from dell) and installed them and then installed the updates for them from this web site. The problem I'm having (before and after applying the upfate) is that only two of the satelites emit sound! Furthermore when I run the creative diagnostic test app (all tests pass) and run the "Test Speakers", the rear left spkr is identified properly; and the right front spkr is identified as rear right and no speakers are identified as front.
    My physical h/w configuration has not been touched during the re-install of windows.
    Any suggestions for getting my audio system working properly again?
    Thanks,
    Phil

    philo wrote:
    I have a SB Li've! 5. Digital card and a set of Creative Cambridge Soundworks 200 Speakers. The speakers consist of 4 satelites and sub woofer. My audio has been working flawlessly for several years until this weekend when I decided to reformat my dri've and re-install Windows XP Pro. I downloaded the dell drivers (card is from dell) and installed them and then installed the updates for them from this web site. The problem I'm having (before and after applying the upfate) is that only two of the satelites emit sound! Furthermore when I run the creative diagnostic test app (all tests pass) and run the "Test Speakers", the rear left spkr is identified properly; and the right front spkr is identified as rear right and no speakers are identified as front.
    My physical h/w configuration has not been touched during the re-install of windows.
    Any suggestions for getting my audio system working properly again?
    Thanks,
    Phil
    I just opened my system and looked at the card. It has the following identification on it:
    . SB Li've!
    2. Model SB0200
    3. Serial Number: MSB020032052655
    So perhaps it is not an SB Li've 5. Digital as I previously thought; regardless I'm still having the same problems. When I downloaded and tried to install the SBLi've! drivers indicated from http://us.creative.com/support/downloads/download.asp?MainCategory=&sOSName=Windows+XP&regi on=&Product_Name=Li've%2&Product_ID=4857&model number=&driverlang=033&OS=0&drivertype=0&x=24&y=5
    I received an error message that no soundblaster card could be found.
    When I searched for drivers by model (sb0200), the website said said, "no such drivers".
    Any help would be greatly appreciated.
    Thanks,
    Phil

  • Cambridge Soundworks system help

    i have what i believe to be a "Soundworks Digital 4.1" system. I am not sure, but assume that this is the correct designation, and it looks just like the "Soundworks Digital 2.1", for which i can find documentation on the Cambridge Soundworks website. I understand from those folks that they produced it for Creative to market and sell (and, apparently, support). I have had it for some time and it has served me well. It uses a cable with DIN-style connectors for digital input, and i use an adaptor that is DIN on one end and mini stereo phone jack on the other, which i plug into the digital output on my audigy 2 card, and the speakers are fully functional. unfortunately my audigy card is failing, and i would like, at least in the short term, to use my onboard audio (soundmax hd, on an asus mobo) as an alternative. the digital output there is an rca style (orange color coded) on the backplane, and i would like to know how, if possible, can i adapt this either to the mini stereo phone plug, or better, direct to the DIN cable, and achieve surround sound, 4 channel control etc?
    i cant find a way to put this question directly to tech support, because the web based input screen insists? i select a product, and this one just doesn't show up. hopefully i can continue to use this excellent sounding system going forward. thanks to all.

    That is something you'd normally set on the soundcard or onboard audio, so you'd probably have to check Realaudio's settings or support for advice on how to get 5. working from it.
    Cat

  • Help with Cambridge SoundWorks!!! PLEASE!

    Hey, guys, I need some help with configuring my 5.1 Soundworks Speaker System... I can't hear anything out of my rear and center speakers...CMSS is out of the question, as my Creative Audigy(LS?) is plugged in, but the Original CD installer says it's not... I have installed some kind of drivers(the original ones from the cd), but, still, my sound card is "invisible" to the Creative Installer...Please help,
    Best regards...

    Yes, my Audigy is plugged in correctly... I had these stereo speakers and they worked fine, but the problem was the same! My drivers won't install via the "Installer"... I have the original CD and all that crap, and still nothing! I only placed the Soundcard where it should be, but I don't know if I need any more wires...My speakers are plugged in like in Creative's Surround Demo etc... I'm now using Win2000[No Service Pack](i used, and I think I will revert to, Windows XP[SP])...What I want to know is: Can I use anything other than CMSS? Is there anything that could make an Audigy LS and a Cambridge Soundworks DTT2200 get along fine? Oh, and I have an Abit motherboard... The model is not important, as my speakers, soundcard, motherboard and a hell lot more come from a guy who sold them...And they worked fine on his PC! The biggest problem is with the drivers... I use the first PCI slot for the soundcard and it kinda works.....Please help if you have any idea...

  • Cambridge soundworks dtt 2500 digital 5.1 on audigy 2

    Hello,I hope you can help me...Here is my problem:I have the speaker-system:cambridge soundworks desktop theatre 5. dtt 2500 digitaland now a Audigy 2 ZS.Everything is ok but the centre-speaker won't talk to me... I've connected the card with the spdif but I have to set the dtt decoder to 4 point surround to hear something from the rear speaker. Without setting to 4 point I can only hear the front speaker (stereo).Now I have deactivated the intern decoder of the audigy 2 zs. Now it is possible to hear dvd in dolby digital 5.!
    But only dvd!
    In the system management I can check the channels seperately but when I see the acoustic waves (symbolic on screen) from the centre speaker but I can't hear anything!
    Please help me...

    Fixed. If anyone has the same problem, not sure what caused it as everything was working before, but a driver update fixed things up.

  • Replacement speaker cables for Cambridge soundworks megaworks THX 5.1 550

    Hi i'm looking for 2 x 5 metre speaker cables for the Cambridge soundworks megaworks THX 5.1 550 has anyone got any ideas on where to get them,have check creative shop on creative web site.thanks

    Also, one of the wires has packed up and I cant find any on creative's website... It is speaker to sub lead, plugs into sub with a Jack and splits into 2 different wires (black and red) to make 2 separate connections to the back of the speaker. Anyone know where they are sold (dont really fancy getting my wallet raped by PC World)?
    Cheers

  • New Soundcard with old Cambridge Soundworks 5.1 speakers on Win 8.1

    Hi
    Just built a new PC with windows 8.1. My old soundblaster live card on my old PC does not seen compatible with new one & the onboard soundcard (realtek) on my new MOBO is inadequate.
    I dont want to spend loads on a new card, so will a budget creative soundcard (

    Originally Posted by super-saint
    Hi
    Just built a new PC with windows 8.1. My old soundblaster live card on my old PC does not seen compatible with new one & the onboard soundcard (realtek) on my new MOBO is inadequate.
    I dont want to spend loads on a new card, so will a budget creative soundcard (
    Sorry never completed above post ... so will start again
    Just built a new PC with windows 8.1. My old soundblaster live card on my old PC does not seen compatible with new one & the onboard soundcard (realtek) on my new MOBO is inadequate. I have a vacant PCI slot but as my old card is quite old, I cant find any drivers for 8.1.
    I dont want to spend loads on a new card, so will a budget creative soundcard work with my old Cambridge Soundworks 5.1 speakers on Win 8.1

  • Cambridge Soundworks computer speakers

    PS1600 4-point surround sound speakers + sub-woofer - Cambridge Soundworks
    My computer speakers have given up the ghost. I am certain it is the switch as when you adjust it the sound sometimes comes and goes in a rather distorted way. I have taken it apart and checked the connections and cleaned it out but to no avail. Anyone know where I can get one of these switches as it seems to be a discontinued product, bought 5 years ago.

    A PM is a private message, it means he has sent you a message directly. You can see your private messages near the top right corner (little yellow mail icon).
    Cat

  • Cambridge Soundworks FPS1600... Volume Control

    Hello everyone,
    I am the owner of a Cambridge Soundworks FPS1600, which used to work brilliantly. Unfortunately, the volume controller broke recently.
    After reading on the internet I found that it's a common problem with this type of product by Creative/Cambridge. I've spent hours of searching for a replacement (including mailing Cambridge, who first replied with a silly oneliner and then chose to never reply to my followup). What you're reading now is a cry for help..
    The volume controller for this product uses a PS/2 (a.k.a. Mini-DIN) connector. The product by default doesn't do anything without this thing plugged in.
    Does anyone have any information at all about a workaround for this controller? Anything? I don't really care about controlling the volume with it, I just want the set to give me sound :'(
    Thanks greatly in advance,
    Rob from the Netherlands
    Message Edited by Nuts on 12-23-2008 04:03 AM
    Message Edited by Nuts on 12-23-2008 04:04 AM

    Hello!
    No, still nothing unfortunately... Thanks for kicking the topic back up though, perhaps someone out there can help us out!

  • HELP: Cambridge Soundworks DTT2200 5.1 - Volume control

    I'm italian, sorry for my english.:smileyvery-happy:
    I have a Cambridge Soundworks DTT2200 5.1 with the connector PS/2 of Volume Control broken.
    I want change it with a new connector, but I don't know the corrispondent COLOR - PIN.
    Please tell me what I have to do.
    http://i35.tinypic.com/o8te8l.jpg

    You have an existing thread open on this topic, so I'm closing this one.
    Cat

  • Cambridge Soundworks DTT2500 and Audigy2 NX

    Hello everybody!!!!
    This is my first post and I would thank if someone could help me. I don't know what is the best way to connect in my laptop in order to enjoy the best sound with dvds and mp3s. The first item (dvds) is ok because I have a RCA cable connection from my Cambridge Soundworks DTT2500 to my Audigy2 NX and I enjoy the DolbyDigital sound this way but with this connection I hear the mp3s in my laptop in a 2 way-speakers, what can I do to hear my mp3s in 5.1 (if there is a better connection among my devices, please let me know)? Thank you very much!

    I own those speakers and as someone else pointed out they're not true 5. speakers, they are only true for movies, not for games, even with the adapter, the center channel will not pick it up. I opted for another manufacturer speakers. When that came out, it was top of the line, high tech etc. But only really for movies, I have it hooked up to my DVD player now and that's all it's good for. And when I had it hooked up to my computer all I was ever able to get out of it was 4. with the spdf adapter and connection.

  • Cambridge SoundWorks FourPoint Surround system turns itself off

    My PCWorks FourPointSurround system is not new, but works great.
    It now turns itself off when no sound signal is present for a while - and turns on after a few seconds of sound output are created. Very annoying.
    [The green power LED goes out and no sound plays. Then it turns on, the green LED lights, and sound plays normally]
    I never experienced this "feature" before. My PC is a new home-brew Pentium 4 with Azalia sound on the Microstar 95P Neo Platinum motherboard.
    Thanks for any thoughts -
    Monty S. [email protected]
    Message Edited by montyshu on 04-20-2005 07:21 PM

    Cambridge Soundworks FPS2000 Digital System Model#: C5W500AC Adapter Model#: TEAD-66-53000U Hope that helps.
    I just found a generic transformer at Radio Shack (gag me!) and they want $90US (again, please) which is a bit more than I ever plan to pay for a Radio Shack part. At $90, I'd just save up and buy one of the newer model systems. =/

Maybe you are looking for

  • GarageBand Not Opening After Recent Update, iOS 8

    I updated GB today, already updating to iOS 8, and now I cannot access GB.  I will not reset GB as I will lose all my music in there, I assume.  Please tell me what will be done or what I need to do.  I am using this on my iPad mini with Retina displ

  • Can anyone help me in DefaultTreeModel insertNodeInto(.. meth.

    hi, I am adding items or nodes to my DefaultTreeModel. And I have a probelm I am trying to build a tree structure by clicking on an item and adding it under the previous one. That is if I add one item and then add another item then the first item is

  • Pre 7 - HD 1080i 16:9 stills

    Hello, I probably won't use all the terms correctly, but here's my best shot: I am editing HD 1080i video and trying to create DVD menus.  I want the backgrounds to be still shots from the footage.  When I locate the frame I want and use the camera i

  • Transport deleted objects in productive

    Hi! Help, plz. What is the right way to transport deleted objects (levels, packages...) to PROD system from QUALITY?

  • Windows - what version.

    Which version of windows would you advise to install please - if vista do I need 32 or 64 bit? Do I need to install anti virus software and which one please.