Can a Windows PC HD be erased using my Mac Pro?

I have an older Windows PC that I want to clean for recycling. I would like to use my Mac pro to do that job, and then hopefully
also clean an Imac that barely is usable (it runs but has to use the Windows monitor. Can any one advise on this, Please????
Thanks in advance.
Tom_______

Let's sort this out. You have a PC you plan to chuck out and want to use your Mac Pro desktop computer from Apple to erase the PC's drive so your info doesn't leak out of your control. You also want to do something similar to the drive on an iMac desktop computer. And you want us, on the MacBook Pro portables forum, to help you.
After pointing out that there are Mac Pro specific forums here...
Yes, you can take the drive out of the PC, stick it in an empty bay on the Mac, then use Disk Utility to do a Security Erase and wipe it clean. Just be sure that both computers are OFF before putting or pulling drives from them. If Disk Utility does not offer an Erase option, select the DEVICE corresponding to the PC's drive, go to the Partition tab and select 1 Partition in the Partitions tab. That will cause the drive to be repartitioned and be erasable again. This happens if the drive is in NTFS format, which OS X cannot write to.
As for the iMac, no need to take the drive out to erase. Restart in Recovery Mode (Command R prior to the startup chime) and use the Disk Utility there to erase the Macintosh HD volume, then Install OS X from scratch.
For more specific details, refer to the Mac Pro and iMac forums.

Similar Messages

How/Can I install WINDOWS 7 64BIT on a 1st Generation Mac Pro ?

Hi, Is it possible to install Windows 7 64 bit on a 1st Generation Mac Pro 2.66Ghz? Apple suggests that it's not possible and yet I've seen several Googled posts where the users have successfully installed 64 bit on a 1st Generation Mac Pro. The problem is that they've done this creating a bootable iso disk(whatever that is) using a Windows computer with imgburn and windows commands. I'm pretty good at following instructions but I haven't seen any instructions on how to install Windows 7 on this machine using a Mac based approach.
I'm using BootCamp and was able to partition the drive into NFTS and "proceed" with installation; however all te installations failed during setup and Windows would not boot; disk repair was not possible. Besides, from what I've gathered, 32 bit is problematic around memory issues.
When I try installing 64 bits, I never get past the "select cd rom 1or 2" message where the keyboard won't work. It is at this point where others say they have successfully proceeded with moving forward by creating a bootable iso disk.
Problem is it's all Windows based with exe files and presupposes I already have Windows running.
I'm not sure I really understand how to create an iso disk, but I do have ROXIO TOAST 10 which is capable of burning "ISO" disks.Does anyone know how to do this and/or can you point me to a place where there are instructions on how to proceed?? While I realize Apple says that some mid 2006 mac pros aren't supported, there are multiple posts of windows users successfully installing Windows 7 on a 1st Generation Mac Pro.
Thanks.

I have a March 2009 Mac Pro dual quad core running Win7 Pro 64 bit. I have Windows installed on a dedicated internal hard drive. There are no partitions, the entire drive is for Windows use.
Here's how I installed it, I did not start with BootCamp. Make sure the drive you're going to use for Windows doesn't have any important files on it because it will be formatted.
1. Update Snow Leopard
2. Place the Windows cd in the Super Drive
3. Shut down the computer
4. Remove all the hard drives except the one you want Windows installed on. Keep track of the order they are in and at the end replace them in the same order.
5. Boot the computer holding down the Option key
6. Boot to the Windows cd
7. Install Windows and format the drive to NTFS
8. When Windows needs to restart during installation you'll need to hold the Option key and boot to Windows, not the Windows cd.
9. After Windows installs, place your Snow Leopard disc in the Super Drive
10. The Drivers for Windows will be installed along with a Windows version of BootCamp.
11. Go to Start > All Programs > Apple Software Update
12. Update again until it's done.
13. You'll also find a BootCamp under Control Panel, check it out.
14. Shut down the computer and replace the hard drives in their original order
14. Now if you turn on the computer it will boot to Snow Leopard, but if you hold the Option key during boot you can select Windows or Mac.

I am thinking of using a Mac pro for share trading. Can anyone share their experience and suggest specs for 30 -40 monitors etc

Hi
I am thinking of using a Mac Pro for share trading.
I am proposing to start small but want to be able to expand up to 30+ monitors.
It must be super quick.
Any help with hardware would be appreciated.
Software is secondary at this point , but open to advice.
I have an iphone and ipad so feel it will better intergrate usung Apple
regards
David

There is no desktop machine that I know of that will support 30+ monitors as is.
Fill the 3 or 4 PCIe slots of any logic board with three port graphics cards and you have the physical cap without additional hardware.
Software is secondary at this point
No, without software, how can you control more than the monitor limit of the OS?
How can you set up the monitors to display the various programs that you will wish to use simultaneously?
Software is a major consideration.
Matrox (and others) have solutions for additional monitors beyond the physical capabilities of generally offered graphics cards.
The caveat here, however, is support software is typically reserved for Windows and Linux systems.
Matrox has a single 8 display card:
http://www.matrox.com/graphics/en/products/graphics_cards/m_series/m9188pciex16/
Matrox has solutions specifically targeting the finance market:
http://www.matrox.com/graphics/en/solutions/trading_analyst/
Though the Mac Pro has more than adequate processing power, I think that you will find (through research) that building a solid machine capable of using several multi monitor cards is going to be what you will need to support more than 8-10 monitors with conventionally offered hardware.
Fun stuff:
http://www.digitaltigers.com/zenview.asp

Can't configure wireless settings on P1102w using a mac

Hi there. I can't configure wireless settings on P1102w using a mac. I have it installed with USB just fine but I want to use eprint (with ios airplay). I run the setup utility looking for some wireless setup option, but it never appears. When I finish the install it tells me to go to the eprint website to download eprint. At that site it has me download the firmware update, which I do, and then at the end of that it tells me to go to the eprint website again, which then downloads the firmware update again. It's an endless loop.
I know I need to get to the built in web server but the config page tells me I don't have an IP address. Which makes sense to me because it hasn't been set up. I can't for the life of me find how to set up the wireless using the driver software on the Mac OS. I try to follow the manuals instructions, but it looks like it is designed for windows users, and the buttons it tells me to look for just don't exist on the mac HP driver software.
Can you help?

Hi,
The Wireless configuration should be made by using the EWS page, which also accessible from Mac OS over a USB connection through the printer setup.
You may find the steps listed below:
Click the Apple icon, then clickSystem Preferences.
Click Print & Fax.
Select your printer and click Open Print Queue.
Click on Printer Setup
Then select Utility
Click Open Printer Utility
Click HTMLConfig. The EWS opens.
Click the Networking tab
Then click Wireless from the list on the left
Under Communication Mode, click Infrastructure, select your network SSID from the Available Network Names (SSID) list, and then click the << button.
From the Security Mode pop-up menu under Authentication, click WEP or WPA/WPA2. Your selection depends on which Wireless Security Protocol your network uses.
Type your WEP/WPA/WPA2 key in the appropriate field, and then click Apply.
In the confirmation box, click OK and then close the HTML Config and Print Queue windows.
Once done, allow 3 minutes to fully establish the connection, then unplug the USB.
Enter Print & Fax and remove the existing USB Print Queue.
Click the Plus button and add the printer over the network.
Please let me know of any issue,
Shlomi
Say thanks by clicking the Kudos thumb up in the post.
If my post resolve your problem please mark it as an Accepted Solution

Im not able to use facetime at all. Do some countries have restrictions. Can anyone help me out ? I use a Mac Book pro retina display with OSx Mountain lion

Im not able to use facetime at all. Do some countries have restrictions. Can anyone help me out ? I use a Mac Book pro retina display with OSx Mountain lion.

FaceTime for Mac: Troubleshooting FaceTime

When I call someone using FaceTime from my mac, they can see me but no hear me. Is there something I need to do to make this happen? I also have an iPad 2 and FaceTime works great on it if I call somebody. Why no sound from my mac FaceTime using a mac pro

When I call someone using FaceTime from my mac, they can see me but not hear me. Is there something I need to do to make this happen? I also have an iPad 2 and FaceTime works great on it if I call somebody. Why no sound from my mac FaceTime using a mac pro and isight camera, mike combo.
If I use google it works. If I use Ichat, it works. If I use skype it works.

This sounds like something similar to https://discussions.apple.com/thread/3388112?start=105&tstart=0.
Try turning down the speak volume (System Preferences->Sound->Output->Output Volume) or the microphone gain (System Preferences->Sound->Input->Input Volume). Do this on both sides of the call.

Hi...m using a mac pro quad core.....its not booting up...i can only see the apple logo and a circle loading...could not get into the login screen

hi...m using a mac pro quad core.....its not booting up...i can only see the apple logo and a circle loading...could not get into the login screen...any suggestions please.....m in the middle of a project and now i have got this one
regards,
v.s.bharan

Welcome to Apple Discussions!
Do you keep your data backed up?
If not, you should always do so*:
http://www.macmaps.com/backup.html
You never know when a hard drive or a directory might go bad. Having a bootable clone is a must.
That link also shows you some tools you can use to recover data.
If you aren't backed up, try buying those tools first, before attempting to repair the directory.
Directory issues can be fixed with these tools*:
http://www.macmaps.com/directoryfaq.html

We are a creative design studio, we need to use apple mac pro server , so we can make more than a different user to use at the same time doing different activities, on different screens, is it possible?what is the max. no. of users that can work efficient

we are a creative design studio, we need to use apple mac pro server , so we can make more than a different user to use at the same time doing different activities, on different screens, is it possible?what is the max. no. of users that can work efficient.
Appreciate your support and if possible , how to do this?

If you want to work with Mac OS X, you need one computer per simultaneous user.
What you are describing, " Multiple simultaneous logins to a single computer" is not avialable on a regular Mac of any description, unless you decide to use Unix tools instead of Mac OS X.
Server will happily store files for many, many users and provide them to multiple (up to hundreds) of computers at "near hard Drive" speeds over Gigabit Ethernet. It can make the File Sharing part easy.

Can I edit anything in a pdf using Acrobat XI Pro?

Can I edit anything in a pdf using Acrobat XI Pro?

And the degree of effective editing may be an issue. Editing is not a recommended task in Acrobat, but instead edit in the original doc and recreate the PDF.

I am useing apple mac pro so can i use apple logo on my visiting card?

i am useing apple mac pro so can i use apple logo on my visiting card?

No. Ownership of an Apple product does not give you the right to use their trademarked and copyrighted logos. From their licensing information:
You may not use the Apple Logo or any other Apple-owned graphic symbol, logo, or icon on or in connection with web sites, products, packaging, manuals, promotional/advertising materials, or for any other purpose except pursuant to an express written trademark license from Apple, such as a reseller agreement.

Can I use a mac pro operating system disk to upgrade a macbook

I need to upgrade my 10.5.8 system to 10.6 before I can upgrade to Lion. I have a mac pro operating system disk for 10.6 can I use this?

No. The gray-colored restore DVDs provided with a Mac are not the retail OS version. They contain only the drivers applicable for the purchased hardware, and the installer has a function to verify the hardware is of the type the disk was created for. If you attempt to use the Mac Pro restore disk on a different model Mac, it will simply refuse to install.

Can the Canon Pixma iP 5000 be used with Mac OS X Version 10.5.8 ?

Can the Canon Pixma iP 5000 be used with Mac OS X Version 10.5.8 ? Thank you

Mail updates are usually part of OSX System Updates and no stand-alone updates.
Try downloading and installing the 10.6.8 Combo Updater from here http://support.apple.com/kb/DL1399
Stefan

Can I use old Mac Pro with new iMac?

I have a Mac Pro (Pre 2007) running on 10.6.8 that is ok for now, but experiencing some degradation in performance. I have 4 drive bays full and memory maxed out. I am looking for a desktop solution that would allow the option to have the latest OSX (such as the latest iMac) and access this old Mac Pro still. Is this possible?
If so, what are some of the caveats?
SoftwareEx: CS6 is compatible with new OSX, but will files saved on new computer still be accessible on old computer?
Access to files
NetworkCurrently using older version of Airport Extreme for home office setup
Any insights would be helpful! I hate the thought of this old workhorse turning into nothing more than an external hard drive, but it is not upgradable to the new operating system.

It sounds like what you want to do is create a simple peer network so you can use the Mac Pro as a storage unit.
This is easy to do, just connect the two with an ethernet cable and log on using the logon and password for the system you want to access. In the general case, this is a bad idea since you you have unrestricted access but you own both machines so security is a very low priority.
Caveats:
     The OS version will determine what apps a machine can run.
     Data is just data as long as both systems use HSF+ or some other common file system.
     Airport may or may not work... but a hard wire will always get it done and transfers data a lot faster.
You almost never get to have it ALL your way when mixing generations of systems, but if you keep it simple it works well. I've had a peer network with 4-6 systems running in my house since the turn of the century. Most Macs support 1000 baseT (gigabit ether) so data transfers up to 80-90MB/sec are easy.

TS1389 Only one song won't play after authorizing my computer. I authorized it over and over. I even deauthorized all computers, and still same results. How can I fix this ? I'm using a MacBook Pro with iTunes 11

Only one song won't play after authorizing my computer. I authorized it over and over. I even deauthorized all computers, and still same results. How can I fix this ? I'm using a MacBook Pro with iTunes 11

Hi Deb,
Deauthorizing all is definitely the way to go. You will just need to authorize your computer again after, as well as your husband's.
Here's some additional information on deauthorizing all:
iTunes Store: About authorization and deauthorization
http://support.apple.com/kb/ht1420
I hope this helps!
- Ari

Hi, I'm using a Mac Pro here. I am trying to connect it with my NAS hard drive. But i could not connect to it because i have an ethernet which connects to the intranet in my company and Air Port for the internet.

Hi, I'm using a Mac Pro here. I am trying to connect it with my NAS hard drive. But i could not connect to it because i have an ethernet which connects to the intranet in my company and Air Port for the internet and it could not detect the the ip address after i input the correct address on "Connect to Server" window. Please help! Urgent! Thanks

I did not say it is not possible.
I said if your company networks are monopolizing both ports, you should talk to them about what options are available.
Maybe you can get the company Intranet over wireless if you change some configuration items such as Subnet Mask.
Maybe you can get on the Internet over Ethernet.
You really need to ask them, and do not let them blow you off because you have a Mac. If they balk, ask them how it would be done on a PC (becasue it will be the same on a Mac).

Can a Windows PC HD be erased using my Mac Pro?

Similar Messages

Maybe you are looking for