Can a Workgroup bridge 352 act as a LEAP client (supplicant) ?
Is it possible for a WGB in Version 8.84 to act as a LEAP client (supplicant) instead of the connected client NICs in the workgroup?
This question is as important as the workgroup could be composed of IP Cameras or other IP devices who could not act as a LEAP Client.
Thank you
Jacky
Hi,
It is not so clear as it seems to be, because several CCO documents are introducing this LEAP ability of the WGB but none of them give details.
http://www.cisco.com/en/US/products/hw/wireless/ps458/products_data_sheet09186a0080088833.html
"For authentication of devices attached to the workgroup, a username and password may be stored in the workgroup bridge in either static or dynamic memory. When authenticated, the workgroup bridge receives a single-session, single-user encryption key from the Remote Access Dial-In User Service (RADIUS) server via the associated AP. With this centralized and standards-based architecture, wireless security scales to meet the requirements of any enterprise."
AND
http://www.cisco.com/warp/customer/cc/pd/witc/ao1200ap/prodlit/wrsec_an.htm
"Figure 6: Workgroup Bridge Security Configuration"
What do you mean about ??
Jacky
Similar Messages
-
Aironet 1242AG duel antenna Workgroup Bridge
I have an Aironet 1242 AG that I have configured as a mobile workgroup bridge. I have noticed when you enable the bridge on Radio0 (G) Radio1 (A) is disabled or cannot be configured as a bride on top. I read it several places in the documentation that it will do this but I haven't seen an explanation as to why. The 1242 is going to be moving throughout a building so if it is possible I need to find a way to configure it so that if Radio0 looses signal it will jump to Radio1 until Radio0 has a good signal again. I can't make any modifications to the stationary broadcasting access points but they are also 1242 access points. If anyone could tell me if this is possible and how to do it or why it is not possible I would be grateful.
Thanks,
MattEnabling the Hot standby activates both the Radio. But both the Radios will be activated at a time meaning communication happens simultaneously on both the Radios. One Radio will not act a s a backup Radio for the other.
-
Question re: BR1310 in Workgroup Bridge Mode
When a BR1310 is in Workgroup bridge mode, it can provide a wired connection from the BR to a device. Can it also service wireless users?
If I understand your question you need more equipment to provide wireless connectivity from the location of the WGB. Add a switch/hub to the output of the BR1310 and an Acess Point to one of the hubs ports.
-
Cisco AP1121G Workgroup Bridge Problem
Hello,
For reference I have attached the following:
Network Diagram
Ping Results Table
Configurations for 1811 router, ap1121g root access point, ap1121g wgb.
I am seeking assistance with the following problem.
Referring to the attached network diagram, I cannot communicate past the ap1121g-wgb in either direction.
Also attached is a result table of ping attempts through the ap1121wgb from each side.
I don't have a problem with the wireless connections. The ap1121g's associate ok.
Based on the ping results the problem appears to be in the ap1121g-wgb configuration, but I have run out of ideas.
The following two cisco documents have been my main reference, besides the cisco command lookup site.
http://www.cisco.com/en/US/customer/products/hw/wireless/ps430/products_configuration_example09186a00805b9b87.shtml
http://www.cisco.com/en/US/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap19-wgb-standby.pdf
Any insight will be greatly appreciated.
Thanks...Robert,
Going back to your original post and looking through the example given in the first URL, I spotted a few lines in the example configurations which apply to older revisions of code, but not newer AP code, so they may be misleading. Based on the parameter availability of station-role workgroup-bridge in your last message, would you be wiling to try the following?
Reset both 1121 APs to factory default configuration (#write erase -- do not save config to startup if prompted)
Give each AP an IP address on BVI1 so that both APs are in the same subnet
Apply the following configuration to the infrastrucuture (root) AP:
dot11 ssid WGB-SSID
authentication open
interface dot11radio 0
ssid WGB-SSID
station-role root
no shutdown
Apply the following configuration to the workgroup-bridge (client) AP:
dot11 ssid WGB-SSID
authentication open
interface dot11radio 0
ssid WGB-SSID
station-role workgroup-bridge
no shutdown
The intended goal with this exercise is to get rid of all config and to try only basic required elements of a WGB configuration, starting with fresh factory defaults. Let's see if it will work for you as a bare-bones setup and then you can add other configuration like encryption and ACLs back in later.
Justin -
Using the 1262 AP in Workgroup Bridge Mode
Client has a building that is located 300Ft apart and would like to provide IP communications for 3-4 IP hadsets back to an IP PBX. They do not want to dig up the parking lot so we proposed using a wireless bridge. I noticed that Cisco discontinue the 1300 and 1400 Wireless Bridge. Can I use a 1262 with external antenna in Workgroup Bridge mode to perfom this functions? I will put a Layer 3 switch on both ends to route traffice (3560C-8). Should I use the Yagi antenna's for outdoor use? Thanks!
You could go WGB, but root/non-root might work better. This will allows you to pass multiple VLAN across the link.
This is a bit old, but it' the Bridge Range utility
http://www.cisco.com/en/US/prod/collateral/wireless/ps5678/ps458/prod_technical_reference09186a00800a912a.xls
HTH,
Steve
Please remember to rate useful posts, and mark questions as answered -
My Bridge Is Acting Wierd With Huge Thumbnails
I just backed up my files on Webroots backup system. Now, the bridge is acting strange. The thumbnails are HUGE. I can use the slider to make them a little smaller but if they get too small they disapear. I reinstalled the Ps and Br part of the disk, but I have also noticed that when I am in Br and want to go to Edit>Preferrences, I always get a Br problem and it has to close. Running on Windows XP, and Ps cs3. Thanks. Glenn
moving thread to the Bridge Windows forum
check out these tech notes:
http://kb2.adobe.com/cps/317/317912.html
http://kb2.adobe.com/cps/404/kb404906.html -
1602 AP - Workgroup Bridge Cannot Associate to Parent AP
Hi All,
For a few weeks now, I have been trying to connect a Cisco 1602 standalone AP to our unified wireless network as a workgroup bridge. Eventually this AP is to be moved to another wireless network where I will need it to run in universal workgroup bridge mode (for non Cisco wireless networks), so I just want to get this working in the office before I take it elsewhere and try to get that to work, as the configuration will be similar.
So far I've been unable to get this 1602 AP to associate to our network. The particular SSID I'm trying to set up is a BYO style SSID, normally if you connect a device you provide your Active Directory username / password and your laptop / phone / whatever connects. I know the username is fine because if I use it on another device it's not a problem.
The AP keeps repeating this message: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating. Cisco.com tells me that this is to do with MFP, however I've changed a number of MFP settings in the SSID and this seems to have made no difference.
I'm thinking this is a problem with authentication or association. I have a question, why do I need to input Radius server information into the config (eap_methods)? When you connect a regular device to this SSID it doesn't require any Radius server settings in order to connect, I don't understand why the AP needs these settings. Also, when authenticating to AD, do you need to include the domain name as part of the username?
Wireless isn't my strong point unfortunately. Is anyone able to help with this? Config and log is below. Many thanks.
version 15.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname WGB-AP
logging buffered 10000
logging rate-limit console 9
enable secret 5 xxxx
aaa new-model
aaa user profile userprofilename
aaa group server radius rad_eap
aaa group server radius rad_mac
aaa group server radius rad_acct
aaa group server radius rad_admin
aaa group server tacacs+ tac_admin
aaa group server radius rad_pmip
aaa group server radius dummy
aaa authentication login eap_methods group rad_eap
aaa authentication login mac_methods local
aaa authorization exec default local
aaa accounting network acct_methods start-stop group rad_acct
aaa session-id common
no ip routing
no ip cef
dot11 syslog
dot11 ssid BYO
authentication open eap eap_methods
authentication shared eap eap_methods
authentication network-eap eap_methods
authentication key-management wpa version 2
dot1x credentials MyCreds
dot1x eap profile EAPTLS
infrastructure-ssid
ids mfp client optional
eap profile EAPTLS
method mschapv2
method peap
crypto pki token default removal timeout 0
crypto pki trustpoint TP-self-signed-88743315
enrollment selfsigned
subject-name cn=IOS-Self-Signed-Certificate-88743315
revocation-check none
rsakeypair TP-self-signed-88743315
crypto pki trustpoint WGB-PEAP
enrollment terminal
subject-name CN=username
revocation-check none
rsakeypair manual-keys 1024
crypto pki certificate chain TP-self-signed-88743315
certificate self-signed 01
30820227 30820190 A0030201 02020101 300D0609 2A864886 F70D0101 05050030
2F312D30 2B060355 04031324 494F532D 53656C66 2D536967 6E65642D 43657274
69666963 6174652D 38383734 33333135 301E170D 39333033 30313030 30383234
5A170D32 30303130 31303030 3030305A 302F312D 302B0603 55040313 24494F53
2D53656C 662D5369 676E6564 2D436572 74696669 63617465 2D383837 34333331
3530819F 300D0609 2A864886 F70D0101 01050003 818D0030 81890281 8100BB10
F5361E52 A573FE8A 247142AD CF53D762 38F7BB42 7E723B2B 5C78100E 7F312442
3BE63A8B 7E826758 3F2914D0 4BBC93A6 CCACA795 927514E7 74561589 444D03BA
C20B80D8 85E52A18 C3B287BF 4A1EEF83 B43DD673 12BF075F 7CA038C0 C31F1FB4
F75C3F86 C09DC703 FB05676B 16B86754 F0F11D4D 36B61F81 DF15C02A 9C410203
010001A3 53305130 0F060355 1D130101 FF040530 030101FF 301F0603 551D2304
18301680 14999B3B 7F4B10FA B95CC90B D7218636 39280AFE 4E301D06 03551D0E
04160414 999B3B7F 4B10FAB9 5CC90BD7 21863639 280AFE4E 300D0609 2A864886
F70D0101 05050003 81810076 27E215C4 C105C66D 15124645 D3F4A538 F977A95F
7AF0FF05 648D41A4 A796F9CB CC6327FF 726DA1D6 290CD438 C2111DF8 208B92B5
63B09FEC 1CA334F7 A4607E71 18EBCB44 0A175BEE 30689849 B4D9222E 7EB1C1DB
F36BDDD3 3F5514A6 8A006A8A A113A44D 7337B6D8 7860AA25 EBAD5588 8543DF88
9E6A3D62 6E875372 277B57
quit
crypto pki certificate chain WGB-PEAP
dot1x credentials MyCreds
username DOMAIN\AD-USER
password AD Password
username Cisco password 7 00271A150754
username DOMAIN\AD-USER
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers aes-ccm
ssid BYO
antenna gain 0
stbc
beamform ofdm
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
shutdown
encryption mode ciphers aes-ccm tkip
ssid BYO
antenna gain 0
no dfs band block
channel dfs
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 spanning-disabled
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
no ip address
no ip route-cache
ip forward-protocol nd
no ip http server
ip http authentication local
ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
ip radius source-interface BVI1
radius-server attribute 32 include-in-access-req format %h
radius-server host xxxx auth-port 1812 key 7 xxxx
radius-server vsa send accounting
bridge 1 route ip
line con 0
logging synchronous
line vty 0 4
transport input all
end
Jan 5 14:34:30.636: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:36:23.730: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:36:42.730: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:38:19.833: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:39:33.901: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:40:49.948: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:42:10.123: %SYS-5-CONFIG_I: Configured from console by console
Jan 5 14:42:42.031: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: No Response
Jan 5 14:42:46.031: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:43:06.058: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: Associating
Jan 5 14:45:18.173: %DOT11-4-CANT_ASSOC: Interface Dot11Radio0, cannot associate: AssociatingWith PEAP there is a certificate being used on the radius server for securing the first phase (outer tunnel). In this scenario the access-point acts like a dot1x client, so like any other client it has to validate the certificate the radius server uses. Therefor the root certificate (and intermediates, if being used) needs to be installed on the access-point.
I never configured an WGB in this way, so I fired on my lab to see if I could get it to work. Sadly I did not manage to get it to work properly, I'm running into "EAP session timed out" messages in ACS (my radius server). I did also ran into the MFP issue, but as long as you configure MFP as optional on the network side, it should work. Because of the CCIE exam, I'm running old AirOS software on the WLC and also the software on the access-point I tested this configuration on (2600) is not that new. So it could be that I ran into a bug testing this, so I would advise you to run the latest software on your 1600. There are WGB related bugs fixed not so long ago. This configuration is supported since IOS 15.2.2(JA) and higher.
If I look at your configuration you still need to actually install the certificate, the trustpoint is empty. Besides that the following configuration changes needs to be made:
eap profile EAPTLS
no method mschapv2
method peap
dot11 ssid BYO
authentication open eap PEAP
no authentication shared eap eap_methods
authentication network-eap PEAP
authentication key-management wpa version 2
dot1x credentials MyCreds
dot1x eap profile EAPTLS
no infrastructure-ssid
no ids mfp client optional
For more information look at this document. -
Workgroup Bridge and local Wifi Config
Hi all, hoping you can help me with this, just need an other brain as mine is empty as I've been staring at this for too long!!!
What I'm trying to config is to have a standalone local WLAN (Built into a VAN) running on the 2.4ghz and then also have a workgroup bridge on the 5ghz to the corporate lan.
Setup is this:
2960<-->1142(autonomous) <--Workgroup bridge on 5Ghz--> 1131(Lightweight)<3560>--<5508WLC> (hope that makes sense!!)
So far I have the bridge working, the 1142 connects to a ssid on the 1131 using psk. I can see the 1142 as an assosiated client on the wlc and I can ping the the lan from the 1142 so I'm happy the bridge is working.
Clients connected to the 2.4ghz ssid on the 1142 can only ping through as far as the AP(1142) I can't seem to get the traffic to pass across the bridge, is there something I need to do to link the 2.4 to the 5ghz bridge link?
Any help always appreciated, cheers.dmantill - Thanks for your link. I have read through and checked my config but my plan is to have a number of clients, all dhcp assigned, connecting to the do0 int for local wlan breakout.
I'm not sure that the passive config will help me there.
Steven - I have enabled the wgb on the do1 int and I am connecting clients on the do0 int for local wlan breakout. Enabling the WGB has not disabled the other radio on my setup.
I was running 7.0.98.0 but have today upgraded to 7.0.98.218 on my WLC but that has not helped.
From what I can tell it looks like my problem just lies with routing traffic across the 2 radios. My local clients can ping as far as the WGB and if I CLI into the WGB AP I can ping the corporate lan on the otherside of the bridge and can also ping from the lan to the WGB. I just cannot seem to get the 2 ssid's to route between each other.
Here's my WGB config, hope this brings some more ideas!!
Cheers,
Jason.
Current configuration : 1555 bytes
version 12.4
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
hostname XXX
logging rate-limit console 9
enable secret 5 $1$ujWI$HMYMAjMfJV2J2WaGa1/JJ0
no aaa new-model
dot11 syslog
dot11 ssid XXX
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 105A0C0A11001D1908
dot11 ssid XXX
authentication open
authentication key-management wpa
guest-mode
wpa-psk ascii 7 080F15480C090D1221
username Cisco password 7 02250D480809
bridge irb
interface Dot11Radio0
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid XXX
antenna gain 0
station-role root
bridge-group 1
bridge-group 1 subscriber-loop-control
bridge-group 1 block-unknown-source
no bridge-group 1 source-learning
no bridge-group 1 unicast-flooding
bridge-group 1 spanning-disabled
interface Dot11Radio1
no ip address
no ip route-cache
encryption mode ciphers tkip
ssid XXX
antenna gain 0
station-role workgroup-bridge
bridge-group 1
bridge-group 1 spanning-disabled
interface GigabitEthernet0
no ip address
no ip route-cache
duplex auto
speed auto
no keepalive
bridge-group 1
bridge-group 1 spanning-disabled
interface BVI1
ip address dhcp
no ip route-cache
ip http server
no ip http secure-server
ip http help-path http://www.cisco.com/warp/public/779/smbiz/prodconfig/help/eag
bridge 1 route ip
bridge 1 aging-time 216000
line con 0
line vty 0 4
login local
end -
Unreachable device behind a workgroup bridge
Hello,
we have a problem, that already occured at two locations:
We installed workgroup bridges (at one location a AP-1242AG connecting to an IOS-AP, at the other location a AP-1131AG connecting to a controller-based WLAN). Behind these workgroup bridges there are devices that talk very little by themselves (about one packet per hour).
So in the IOS-WLAN they are reachable only after pinging the device from the AP to which the WGB is connected. In the controller-based WLAN they are only reachable from the WGB itself, not from the rest of the LAN.
My suspicion is, that these devices disappear from the ARP-/Mac-Address-tables because of the little traffic they send. How can we work around this problem? Static ARP- and/or MAC-Entries? But where to place them, in the core, on the APs?
I would appreciate any help.
Thanks,
SebastianHere is the URL for the WLC configuration and troubleshooting guide which will help you :
http://www.cisco.com/en/US/tech/tk722/tk809/technologies_tech_note09186a0080810880.shtml
http://www.cisco.com/en/US/products/hw/modules/ps2797/products_tech_note09186a0080811085.shtml -
How to setup LAPAC1750-PRO with LAPAC1750 Workgroup Bridge Mode as WiFi Extender
I've got following devices:
1 LRT224 Dual WAN Gigabit VPN Router (Load Balancing)
2 LAPAC1750-PRO Access Points
6 LAPAC1750 Access Points
I'm supposed to make a Cluster between 2 LAPAC1750-PRO and then connect the 6 LAPAC1750 using Workgroup Bridge Mode, but after purchasing and while configuring, I found the strage thing that:
If I need to setup a Workgroup Bridge Mode, the clustering will not be available (so I need to modify the changes on either PRO APs whenever I need to perform some) and the Bridge Mode needs to be disable if Clustering is ON or vice versa.
Spoiler (Highlight to read)
+--- The Configuration ---+
I've made 2 subnets:
192.168.1.x (Existing)
192.168.10.x (New)
and configured 4 APs on each (1 PRO and 3 Normal using Trunking between 2 HP 1910 24 Switches) and then again found some strange thing that:
Only 1 Normal AP can be connected to PRO in a Workgroup Bridge Mode, and vice versa.
+--- The Configuration ---+I've made 2 subnets:192.168.1.x (Existing)192.168.10.x (New)and configured 4 APs on each (1 PRO and 3 Normal using Trunking between 2 HP 1910 24 Switches) and then again found some strange thing that: Only 1 Normal AP can be connected to PRO in a Workgroup Bridge Mode, and vice versa.
+--- The Problem ---+
--- Please correct me if I'm wrong
It supposed to extend the Wireless Range, therefore I need to do the following:
PRO AP needs to connect to the AP 1 of and the AP 1 then connects to AP 2 and so on in Workgroup Bridge Mode ...
OR
All the APs needs to connect to the PRO one by registering one by one in Workgroup Bridge Mode
Thanx in AdvanceThanx! The information is very helpful.
-
How can I prevent Bridge from altering my photos?
HELP!!!
Within the past few days my Bridge CS4 program has been making my life miserable. I had been utilizing the program to batch photos from my extensive photo library, rename them, sort them (i.e., change sort/ordinal number), and the like without any difficulty and then suddenly, after executing such processes my thumbnails turned completely white and would not open in Bridge, Photoshop CS4 Extended - much less anything else. I tried reopening them as .jpg's, .psd's, .tiff's to no avail. I went into properties on each photo and checked the "open with" tab, and it noted that the photo was not recognized. I had some moderate success opening them with Quicktime Picture Viewer, but converting them back to a Bridge readable format (i.e., their original state) proved impossible. Having noticed that Quicktime had hijacked nearly my entire photo opening process, I uninstalled it in the hope that it would solve the problem. It didn't. I then went into Bridge and Photoshop CS4 preferences to try and modify how photos were opened, and couldn't seem to find anything applicable. I did, however, increase the memory and cache allocated to each program substantially.
Last night I ran into more problems with Bridge. While scanning both photo negatives and prints into Bridge and saving them into various files, I encountered the same problem indicated in paragraph one. I tried scanning several of them a second time and succeeded; however, I had to save them to a different file and give them dissimilar names in .tiff format. In the process I found more than a dozen ways to spell "Mexico," "Tokyo," and "Ukraine"! They would not save as .jpg's or .psd's.
I use Windows Vista Home Premium SP1, have a Pentium 4 Dual Core (2.8) processor, 4 GB Memory, Nvidia GE Force 7600 video card (yes, the drivers are up to date), and Hewlett Packard Photosmart C7180 and C7280 printers for scanning. All of the photos involved are stored on a Maxtor One Touch 1TB Turbo auxillary hard drive.
Also, could anyone suggest how I can get the SD/MMC card reader on my PC to work?
Thanks to any and all for assisting me with my problem.
Wolfgang Holst
Big Bear Lake, CAThank you curt y for your quick response. I have seen your recommendations on the adobe forums link in the past and many of your solutions
seem to have helped other people with Bridge problems. I took your suggestion and gave it a whirl - all preferences were restored to defaults - and the problem continues. I get the feeling the problems lies with the program's interaction with Windows.
Having tried a few more things, I've found that I can move the photo shell (the inscription underneath the thumbnail states, "Window Shell Common") to my desktop and open it there with Photoshop (i.e., going through the song and dance of "open with" and clicking on the CS4 icon, where it opens up in RAW). I must then move it over to Photoshop CS4 and save it as a .jpg or a .psd. Unfortunately, after all this it still won't open in Bridge. By all appearances, Bridge somehow has become corrupted and I'm probably going to have to do a complete Photoshop CS4 uninstall and reinstall.
I've spent hundreds - if not thousands - of hours scanning into my system some 10,000 photographs of my travels (yes, they are backed up on discs), and Bridge should not be negatively impacting my ability to organize and manipulation them as is happening now. If the uninstall/reinstall does not resolve the problem, I'll be back on this forum for more suggestions.
As for the card reader issue, I'm well aware of the 2GB/over 2GB issue. I typically use a 4GB or more card in my camera. I can download fine through my HP 7180 and 7280 card readers, but my HP 1518n card reader is a different story. I'll work a little more on it, too.
Thanks again.
Wolfgang Holst
Big Bear Lake, CA
Date: Thu, 18 Jun 2009 08:49:46 -0600
From: [email protected]
To: [email protected]
Subject: How can I prevent Bridge from altering my photos?
Have you tried resetting your preferences by holding down the Ctrl key and starting Bridge? You will get a reset window, choose all 3 options.
The only thing I know about card readers is that there are 2 versions. One for cards of 2 gigs or less, and one for HD cards over 2 gigs. Make sure card and reader match.
> -
I have adobe cs6 and I can't get bridge or mini bridge open. All I get is "waiting for bridge." can anyone help?
This tech doc should help. Simply try out each step one at a time until it works.
Error: Waiting for Bridge | Mini Bridge panel
Gene -
Bridge wont recognizw my Nikon d610. I am running windows 8 and photoshop cs6 with 8.6 camera raw plug in. How can I get bridge to recognize my camera? Thanks!!
That camera model has been supported since ACR 8.3 and it is most certainly supported by ACR 8.6 and ACR 8.7 (beta).
Either you have damaged, corrupt image files, or a faulty Photoshop and/or ACR installation.
If there are no privacy issues, you can post one of your files to the FTP service of your choice (such as Dropbox or yousendit.com), post the link to it, and someone here can take a look at it for you. -
Hi, I changed my credit card, so my monthly pâyment expired. Now I changed the credit card details online...but I still can't use bridge or photoshop. I tried everything I could do as suggested online...
Can you help me asap?Unfortunately, only Adobe customer service can assist you with your issue. These are user forums; you are not addressing Adobe here.
Click on the link below, and after that click on "Still need Help? Contact us."
Then on the next page, click Chat
There is also a phone option.
http://helpx.adobe.com/contact.html?step=PHXS_downloading-installing-setting-up_licensing- activation -
Can I use Bridge to export image data into a .txt file?
I have a folder of images and I would like to export the File Name, Resolution, Dimensions and Color Mode for each file into one text file. Can I use Bridge to export image data into a .txt file?
Hello
You may try the following AppleScript script. It will ask you to choose a root folder where to start searching for *.map files and then create a CSV file named "out.csv" on desktop which you may import to Excel.
set f to (choose folder with prompt "Choose the root folder to start searching")'s POSIX path
if f ends with "/" then set f to f's text 1 thru -2
do shell script "/usr/bin/perl -CSDA -w <<'EOF' - " & f's quoted form & " > ~/Desktop/out.csv
use strict;
use open IN => ':crlf';
chdir $ARGV[0] or die qq($!);
local $/ = qq(\\0);
my @ff = map {chomp; $_} qx(find . -type f -iname '*.map' -print0);
local $/ = qq(\\n);
# CSV spec
# - record separator is CRLF
# - field separator is comma
# - every field is quoted
# - text encoding is UTF-8
local $\\ = qq(\\015\\012); # CRLF
local $, = qq(,); # COMMA
# print column header row
my @dd = ('column 1', 'column 2', 'column 3', 'column 4', 'column 5', 'column 6');
print map { s/\"/\"\"/og; qq(\").$_.qq(\"); } @dd;
# print data row per each file
while (@ff) {
my $f = shift @ff; # file path
if ( ! open(IN, '<', $f) ) {
warn qq(Failed to open $f: $!);
next;
$f =~ s%^.*/%%og; # file name
@dd = ('', $f, '', '', '', '');
while (<IN>) {
chomp;
$dd[0] = \"$2/$1/$3\" if m%Link Time\\s+=\\s+([0-9]{2})/([0-9]{2})/([0-9]{4})%o;
($dd[2] = $1) =~ s/ //g if m/([0-9 ]+)\\s+bytes of CODE\\s/o;
($dd[3] = $1) =~ s/ //g if m/([0-9 ]+)\\s+bytes of DATA\\s/o;
($dd[4] = $1) =~ s/ //g if m/([0-9 ]+)\\s+bytes of XDATA\\s/o;
($dd[5] = $1) =~ s/ //g if m/([0-9 ]+)\\s+bytes of FARCODE\\s/o;
last unless grep { /^$/ } @dd;
close IN;
print map { s/\"/\"\"/og; qq(\").$_.qq(\"); } @dd;
EOF
Hope this may help,
H
Maybe you are looking for
-
Ok, this is a very confusing topic. I have connected Apple Care, and they understand what I'm trying to do, but say there is "no way" that it can be done. But I know there is a way so hopefully someone can help. First, this is what I'm asking for...t
-
I'm rapped in my ipad, I work with it every day. It's so handy and I have a lot of fun with it as well; so that's the up side of it. The down side is, emailing for some reason when I send a email. I get two copy's sent back to me and my iphone as wel
-
Apple unable to unlock replacement unlocked iPhone 4S
This is especially important to anyone who purchased an unofficial unlocked iPhone 4S in the USA with an AT&T micro-sim rather than the official unlocked iPhone 4S SKU packages (starting on 11/11/11). On Oct 17th I purchased a 32gb iPhone 4S at an Ap
-
All of sudden My Crive is showing Low disk space. Can any one help me int his issue. And also in my E drive this is not even a single file But it is showing 7 GB less . What will be the problem. Please help me ... Sudheer
-
Is arch the distro for me?
Hiya all, just want to thank you in advance for your time and advice:D anyway, my plans are to buy the linux version of the MSI Wind when it is released in a few months. (http://www.msimobile.com/DetailPage.asp - d_NB_Linux) I have used SUSE (the dis