Can Agilent VEE 6 Pro be used to interface to the NI-DAQmx drivers?

Can Agilent VEE 6 Pro be used to interface to the NI-DAQmx drivers?
I have previously used VEE 6 Pro and the NI_DAQ "Traditional" interface, (Version 6.9.2) using the DLLS functions to communicate to the cards.
I now want to add one of the M series DAQ cards to an existing setup for a new test program. It appears that M-series is only to be supported by DAQmx.
Is it possible to use VEE 6 together with DAQmx?
If so, will the old programs still function if I upgrade to NI-DAQ 7.3. and develop the new program using the NI-DAQmx interface?
Can "traditional" DAQ be used simultaneously with the mx driver?
Thanks

Greetings,
You would need to contact Agilent to see if they have build DAQmx support for the VEE 6 Pro. As you mentioned, VEE 6 Pro makes DLL calls to the NI DAQ driver.
You are correct in that the M-Series boards are only supported in DAQmx. It is possible to use Traditional DAQ and DAQmx at the same time as long as you are using them on two different boards.
Hope this helps,
Anuj D.

Similar Messages

Just converted word to PDF so that I can save on iPhone and subsequently use. Where is the file??

Just converted word to PDF so that I can save on iPhone and subsequently use. Where is the file?? I have no idea where it is!! Extremely frustrating and not at all user friendly!! Took my 6.99 British pounds and not a sausage to be had!!

It sounds like you may have purchased a CreatePDF subscription through safari, using our web interface. If this is the case, the good news is that subscription will also work with the (free) Adobe Reader. Simply install the Reader from the App Store:
https://itunes.apple.com/us/app/adobe-reader/id469337564?mt=8
Once installed, you can then use "Open In" from another app like Mail to open the Word document in Adobe Reader. Reader will show the word doc, but it will also show you a message pointing to the "convert" button (A document with an arrow through it in the toolbar). Pressing this button should prompt you to sign into Acrobat.com. Use the same account you used to purchase your subscription and Reader will upload the word document for conversion, placing it in the Acrobat.com and Outbox section of the Reader. Please let me know if you have trouble!

My ipod nano gen 4 is stolen! He is my first love with ipod. Can I lock this device by use serial number of the device? I don't want any bad guys use or do anything with my love one. Please let me know if have the way to do thanks.

My ipod nano gen 4 is stolen! He is my first love with ipod. Can I lock this device by use serial number of the device? I don't want any bad guys use or do anything with my love one. Please let me know if have the way to do thanks.

zenith_nm wrote:
My ipod nano gen 4 is stolen! He is my first love with ipod. Can I lock this device by use serial number of the device? I don't want any bad guys use or do anything with my love one. Please let me know if have the way to do thanks.
Nope!
http://support.apple.com/kb/HT2526 How to report lost or stolen Apple product

How to use multiple Interfaces for the same BS?

Hi @ ,
Is it possible to have a scenarion where i am using multiple interfaces in the same BS based upon some conditional field in the message.
I amnot able to get the solution I know with condition editor I can have multiple receivers but in my scenarion based upon message fiels i have to decide which BAPI to be used and wht mapping and then post it to the same System
Any help will be highly rewarded
Regards

Hi-
Yes it is possible you can use multimapping for mapping the interfaces.
To know more about multimapping see
http://help.sap.com/saphelp_nw04/helpdata/en/21/6faf35c2d74295a3cb97f6f3ccf43c/content.htm
Some more helpful links
/people/jin.shin/blog/2006/02/07/multi-mapping-without-bpm--yes-it146s-possible

What is the use of interface in the adobe forms

Hi friends,
can any one tell,
what is the use of interface in the adobe forms for desigining the form.

The main purpose of the form interface is to send the application data to the form.
The form interface is created separately from the form, which consists of the form context and layout. When you create a form, you must assign it to a form interface.
please have a look at the link below for more info:
http://help.sap.com/saphelp_nw70/helpdata/EN/96/6ee0d5b39640d68fc0078fc575114a/frameset.htm
http://help.sap.com/saphelp_nw70/helpdata/EN/f2/21021b911f4c0cae11459a4ce0bc62/frameset.htm
hope this helps,
harman

Can't boot MacBook Pro 13" (mid 2010) after installing the update SMC 1.6

First for a long time was a white screen and noisy cooler
After the system battery icon was crossed out and the indicator on the left side of macbook does not show anything and everything worked cooler at high speed (he was cold macbook)
After reboot appeared and the system has stopped running
Few days ago I have installed Mac Os X 10.6.4 but when the system had started working I saw my desktop it was at least 2-3 sec, after that macbook went to sleep mode. I pressed any key macbook and system started working, but without lighting screen. I used bright lamp and saw that all shortcuts and indicators (like wifi, battery etc.) have appeared on my desktop. After 2-3 sec macbook went to sleep mode again. Pressing on buttons and light from lamp gave me possibility to done update to 10.6.5 and after to 10.6.8. But at the end situation was not changed.
When I boot macbook with using install DVD, I can use all utilities (disk utility, network util etc.) and macbook don't goes to sleep mode and screen has light. In my opinion reason of this - not correct installation latest EFI or SMC updates. I tried to install EFI update 2.0 and SMC 1.5 for 10.6.5/10.6.8, but system showed me that I can't do this update. I'll try to find some way to make EFI update, maybe this would help me solve this problem. P.S. answer from Applle support: Our updates can't to break your macbook... it's just coincidence. Probability theory it's just mystification
this is info about my MacBook Pro 13" (mid 2010) MC374ll/A. As you can see I have SMC version 1.68f99 instead 1.62f7
http://support.apple.com/kb/HT1237 - I found information about right version SMC for my MacBook Pro mid 2010 13" from this table.
If somebody has same problem, welcome to discussion. Maybe we'll find way to solve this problem... Or Apple will make fixes for us.

After some time, I found answer how I can repair my MacBook Pro 13" (mid 2010). As I was writing early - Mac Os X update SMC 1.6 broke my computer.
This is a link on repair instructions: http://habrahabr.ru/sandbox/67092/
As a result I write this post on my old (but working) MacBook Pro.

Pro*C using client server and the sqlca - any takers

Hi all
This is my 1st post and it's about Pro*C.
At work, we are porting our Pro*C apps from VMS to XP/NT. Has anyone done this before, anything to be aware of?
Also am planning a client/server architechture for my next project, but with Pro*c, and am concerned about the conficts of using the sqlca between child processes...any ideas/suggetions?

Don't cross post
[http://forums.sun.com/thread.jspa?threadID=5384591&messageID=10700568#10700568]

Can I install windows again without using bootcamp to create the usb boot?

Hi, I have installed Windows 7 on my Mac with Bootcamp, but the free space Disk on my Windows partition is full.
Is there any way of install Windows 7 again if I have the usb with Bootcamp Tools and Windows ISO installed yet?
Thanks,
Regards.

If you already have built the USB with BC drivers and Windows ISO, run BCA and use the last option. It may say Remove or Install, depending on whether you already have Windows in your disk or not. If the installation is incomplete, use BCA to delete the current partition and start over again.

Use two interfaces on the same network

Hello every one,
I actually starting to work on a cisco project. I'm a beginner on networking and cisco technologie.
For my project we use a router 2921.
We got two network:
- Network A: 192.198.0.X / 255.255.255.0 / Gateway 192.198.0.1
- Network B: 162.168.0.X / 255.255.0.0 / Gateway 162.168.0.1
Each network use switch, Switch A (connecting to network A) is connected to interface G0/0.
And Switch B (connecting to network B) is connected to interface G0/1.
Router well configured as:
- G0/0: ip address 192.198.0.1 255.255.255.0 (network A)
- G0/1: ip address 162.168.0.1 255.255.0.0 (network B)
Every think working fine.
The problem is with this one, we need to connect a computer on G0/2. This computer is configure as network A (192.198.0.10 / 255.255.255.0 and same gateway).
I can't configure G0/2 as 192.198.0.1 255.255.255.0 (network A), cause G0/0 use this adresse.
I can't put this computer on the switch A, my only physical possibilité is to connect him on G0/2.
We just need to use interface G0/0 and G0/2 as a switch on the router with the same gateway (192.198.0.1)
How can i connect this computeur? How can i configure two interfaces on the same network and same gateway?
Thanks you

I would just put the PC on a different network, but if you really want it to be in the same network, you could use IRB to connect two of the interfaces on the router at layer 2.
Here is an example config for IRB:
interface FastEthernet0/0
bridge-group 1
interface FastEthernet0/1
bridge-group 1
bridge irb
interface BVI1
ip address 192.168.0.1 255.255.255.0
bridge 1 route ip
Notice that the physical ports do not have IP addresses on them, the IP for the subnet is on the BVI interface.

Can a dead MacBook Pro be used as a target disk?

I have a Santa Rosa MacBook Pro, 15 inch display, with 250 GB and nVidia GeForce 8800 GT. A few weeks ago I left it to sleep, and the battery eventually drained (the blinking ceased). Now, if I plug in the charger, the light is always green (so are the little LED lights near the battery panel). If I hit the power on button, it doesn't respond.
I've resetted the PRM, and taken the battery out for 10 minutes and so on but it hasn't helped.
Would this call for a change in battery? I described it to a member of the Apple team at the Apple store (since I didn't have my laptop at the time we went to the mall) and he said it didn't sound good, but that's all he said.
It has once been in repair for a faulty logic board which Apple covered under an extension program, but that was a year and a half ago. Besides that it was working like a dream until this happened.
I have no warranty and I'm especially worried about the data I might lose because the external HD that Time Machine used died a few days ago.
I was thinking of using the MacBook Pro as a Target Disk, and connect it to my working Apple MacBook. But won't the MacBook Pro have to be switched on?
Please help! I would like any suggestions, detailed walkthroughs so I can atleast save my data.
Thanks!

...If I hit the power on button, it doesn't respond...
Yes, the computer must be able to at least turn on in order to work in Target Disk Mode. Your only option would appear to be to remove the drive from the Macbook, then put it into an external case so you could use it as your would any other external drive.
...the external HD that Time Machine used died a few days ago....
Oh dear, Murphy seems to have taken a large interest in you. While it won't help you now, for the future, what I always recommend to my clients is to have "at least 3 copies". Basically, this is the original, one "normal" backup and another backup that's stored offsite in a firesafe. In addition to dead hard drive like you had, offsite is insurance against theft or damage to building and contents. And firesafe for obvious reasons, but that is at your discretion depending on the importance of the data. But even if you don't go offsite, at least manually make another copy of your documents, iTunes Library, iPhoto Library, etc. on to another hard drive, flash drive, CD, DVD, etc.

How can an email account be created using Java mail on the FLY.

Scenario is such that i am using mail server from MDaemon.com and JavaMail api,and making Email website like yahoo...some what ! but how can a user create his account by just filling the form and when he enters his account be created in Mail server..

Last time I checked MDaemon has its own API for account management. I have never tried to do anything with it but their sales literature says it exists.
Account management will be specific to the platform and mail server software. This is beyond the scope of JavaMail which is for message transport (and management to an extent on IMAP servers), not account management on the server.
The other alternative is to write your own application that modifies the structures used by mdaemon but since it already has an API why bother.

How can I set up MRP to use QI Stock at the Vendor, for Planned Ind Reqmts

Hi experts,
We are running ECC 6.0.
In one of our plants, we have a lot of components that are available as QI stock in Material Provided to Vendor status.
We build SKUs (MRP type M3) at the top level in the BOM, and the SKUs use the above components. We mostly enter demand at the SKU level in the plant (LSF).
We have set up the source list for all the SKUs in this plant with MRP = 1.
When MRP runs for the components (MRP type PD), system is able to first allocate the QI stock to any of the requirements that are driven by the higher level SKUs. Only then, it creates Planned Orders for the components to account for the shortage.
Issue : We now enter forecast (LSF) directly at the Component level (for some Materials). Now, even though we have excess
component stock to handle all the demand (dependant demand driven from the SKUs + LSF at the Component level), system doesn't allocate the excess QI stock to the LSF demand at the component level. It just creates Planned orders.
Strategy Group for both the SKU and Component is 10. We don't have MRP Areas implemented.
I tried setting up the source list at the Component level using the vendor but there is no use.
Does any one have an idea on how this can be addressed?We want to be able to use up the QI stock first before we create Planned orders.
Thanks,
Rao

How can you create QI stock first before your planed order from MRP run? Do you know this is not standard SAP ?

Can you run premiere pro on two different computers with the same log in?

can I install and buy adobe premiere pro and run it on two different computers. Got a desktop at home that I work from and a laptop to bring to clients... So far my trial only want to work on one of the assets?? Many thanks

Hi Dream5,
Please check the below forum discussion.
Creative Cloud multiple computers
Also, check this link for more information and errors.
Error "Activation limit reached" or "Sign in failed" | Adobe products
Regards,
Vinay

I have ipad and streaming a movie using apple tv to my big screen tv, can i browse online ising online using my ipad while the movie is still on?

I Have an ipad mini 2 with ios 8.0, also apple tv 3 generation. Can i use ipad mini and watch streaming to my smart TV using apple tv and browse online on ipad without disconnecting the streaming mivie while is on?

See:
iOS: Troubleshooting applications purchased from the App Store
Contact the developer/go to their support site
Restore from backup. See:
iOS: How to back up
Restore to factory settings/new iPod
BTW this is the iPOd touch forum

Macbook pro only uses 4gb out of the 8gb installed..

Hello everybody,
I have an early 2011 15" i7 macbook pro, I upgraded the memory ram to 8gb. when i go to activity monitor it shows the 8gb but it never uses more than half, even when im running multiple software at a time like autocad, illustrator and other 3d modeling software... please helpme i thinkf its vmware fusion which i have installed but not running, I havent find a way to fix this and its driving me crazy since i feel i installed the 4gb extra for nothing....

WELCOME!http://i29.tinypic.com/2ef7yfn.gif!
A few suggestions:
First, disconnect all devices from your MBP if applicable.
http://support.apple.com/kb/HT1411 Apple Portables: Resetting the System Management Controller (SMC)
http://docs.info.apple.com/article.html?artnum=2238 Resetting your Mac's PRAM and NVRAM
If you make it to your desktop, try running +repair disk+ from your *software install DVD* and afterwards, run +repair permissions+ *from your HD.*

Can Agilent VEE 6 Pro be used to interface to the NI-DAQmx drivers?

Similar Messages

Maybe you are looking for