Can AIR-CAP1602i-x-k9 be converted to stand alone??

can air-cap1602i-x-k9 be converted to stand alone??

Yes , you can convert the AP to stanadlone by pushig the below image into the AP
http://software.cisco.com/download/release.html?mdfid=284366503&flowid=37523&softwareid=284180979&release=15.2.4-JB3a&relind=AVAILABLE&rellifecycle=ED&reltype=latest
You can use the below method to convert the same
Using a TFTP Server to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release
using a TFTP server: This method is for local conversion.
Step 1 The PC on which your TFTP server software runs must be configured with a static IP address in the range
of 10.0.0.2 to 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a
1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200
series access point.
Step 4 Connect the PC to the access point using a Category 5 or better Ethernet cable.
Step 5 Disconnect power from the access point.
Step 6 Press and hold the MODE button while you reconnect power to the access point.
Step 7 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds), and release the
MODE button.
Step 8 Wait until the access point reboots as indicated by all LEDs turning green followed by the Status LED
blinking green.
Thanks..

Similar Messages

Can AIR-SAP2602E/I-C-K9 convert to controller based AP?

Can AIR-SAP2602E/I-C-K9 convert to controller based AP?
both S2G1K9W7-15202JA/ JB available?

here are the procedure:
https://www.youtube.com/watch?v=wWDrFjwVNb0
http://rscciew.wordpress.com/2014/05/07/access-point-conversion-lap-to-aap-and-vice-versa/
Regards

Can someone send me the link to the stand alone version of light room 5 were I can buy it. Thank you in advance

Were can I found the stand alone version of lightroom 5?

Rob,
Thank you so much.
In one way or another I managed to purchase the upgrade of lightroom instead of full version.
It is now corrected, thank you so much
Best Regards,
Fredrik
18 aug 2014 kl. 11:11 skrev Rob Cole <[email protected]>:
Can someone send me the link to the stand alone version of light room 5 were I can buy it. Thank you in advance
created by Rob Cole in Photoshop Lightroom - View the full discussion
If you go to the main Lightroom page - where most links take you to cloud signup, at the very bottom, click on "Products" - scroll down to 'Lightroom'..
Products
Please note that the Adobe Forums do not accept email attachments. If you want to embed a screen image in your message please visit the thread in the forum to embed the image at https://forums.adobe.com/message/6649902#6649902
Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
To unsubscribe from this thread, please visit the message page at . In the Actions box on the right, click the Stop Email Notifications link.
Start a new discussion in Photoshop Lightroom by email or at Adobe Community
For more information about maintaining your forum email notifications please go to http://forums.adobe.com/thread/416458?tstart=0.

Can Cisco 1041N WAP Be Configured as a Stand-alone device

I'm out at a remote site and we've been futzing with configuring this to be the site's WAP. But it's looking like it's
meant to only be used in conjunction with a central controller. Is there any way to have it work like a stand-alone
device like the good old 1200 (which I am missing very much at the moment).

According to the Cisco Software Download Centre, you can load autonomous IOS into the 1040 AP.
Products
Wireless
Access Point
Cisco Aironet 1040 Series
Cisco Aironet 1040 Series Access Point
IOS Software
Follow the proceedure below to convert the AP from CAPWAP to Autonomous IOS.
Using a TFTP Server to Return to a Previous Release

How can I read the complex data for the stand-alone offline time-frequency analyzer, which only accept real data, that is one-column or one row data ?

I have real complex data (i,q data) for the ISAR imaging. I don't have any knowledge of Labview programming. I bought this signal processing toolset to use only stand-alone time-frequency analyzer.

In the LabVIEW functions palette on the block diagram, if you go to Numeric>>Complex you have to VI's that splits a complex number into rectangular or polar components. Click on the help file for those VI's to see the kind of datatypes you can wire to them.
Cyril Bouton
Active LabVIEW Developper

Can the new airport be used as a stand alone to the printer for the iPad

Can the new airport express be used with a network printer as a stand alone with just a iPhone and a iPad, no computer to set it up with?
It has Internet access.

You're referring to Target Display Mode Mid 2011 iMacs this letter will explain how it works or in your case will not work () with your mid 2010 MBP. Sorry to be the bearer of bad news.

Can I purchase Adobe Premiere Pro as a stand alone?

Hello,
I have the Adobe Design Suites. Can I purchase the Adobe Premiere Pro without buying the full Production Suite?

Where would i do so. All I see is Upgrade portion here
http://www.adobe.com/products/premiere.html
Even though I don't have a previous version of Adobe Premeire, would this be the one I select?

How can i install apple mobile devices as a stand alone install.

I have installed itunes a number of times but apple mobile devices won't install. What can i do?????

The Apple TV is the only device I've been able to find at this point that can handle video via AirPlay. So unless someone else knows of a device I haven't been able to find, you'll either need to get an Apple TV or, as Andreas suggested, connect to the projector via an adapter and cable.
Regards.

Can we install ESR (ES repository) in a stand alone fashion?

I guess NOT. Because ERS needs a JAVA engine, right?
Thanks!

Yes, the project owner need to be aware of it. As bazzza mentioned, the Agent will be installed on the Linux box and it will connect to the database on linux at set intervals to collect monitoring data.
So you are looking at additional resource usage (Memory, CPU, Disk) on Linux box. And you should plan for additional Oracle Connection License for the database if you use Named User License.

SSH issue when converting stand alone to RAC -- manually

Hi All,
I face an issue with SSH when trying to convert a stand alone database to RAC (2 node). I am trying the manual way.
Plan:
Migrate the filesystem to ASM
Install the cluster
Create another ASM instance on node 2
Create another DB instance on node 2
Register the new ASM and DB instance with cluster manually
I have successfully completed the filesystem conversion to ASM.
When performing the pre requisites for cluster installation, i am facing problem when configuring the SSH.
Node 1 -- Has the existing stand alone database
Unable to do SSH from node 1 to node 1 (self) or from node 2 to node 1.
However i am able to SSH from node 2 to node 1 and node 2 to node 2 (self)
Steps which i tried already:
1)Created another user(test) on both the nodes and try to establish SSH to see if configuration problem is with this current user (RAC1). SSH configured successfully with user test
2)Copied the profile of RAC 1 user on node 2 to node 1 and retried the SSH configuration. But it failed
3)Dropped the user RAC1 on node 1, deleted all the hidden files in home directory so that they can be created freshly when the user (RAC1) is recreated. Tried SSH configuration again and it failed
Can you please help me to fix this issue and identify the root cause of this.
Please let me know if you have any questions.

user 777111 wrote:
I face an issue with SSH when trying to convert a stand alone database to RAC (2 node). I am trying the manual way.What operating system?
To create automated ssh connectivity between 2 accounts (same platform, or different platforms, does not matter):
1. generate a ssh key for the current account (command: <i>ssh-keygen -t rsa</i>)
2. create the file +$HOME/.ssh/authorized_keys+ and copy all the RSA public keys from all accounts that are trusted (this includes the current account's public key) - public key file is +$HOME/.ssh/id_rdsa.pub+
3. manually test connectivity from the trusted account to the other accounts - as the signatures of those servers need to be accepted and stored in +$HOME/.ssh/known_hosts+
When setting this up for RAC, you first need to generate the RSA keys and then do the above on one node. Create +$HOME/.ssh/authorized_keys+ containing all RSA public keys. Build +$HOME/.ssh/known_hosts+ by ssh'ing from that node to the other nodes (do not need a successful logon - only need to accept servers signatures).
When done, copy both these files to the +$HOME/.ssh+ directory on all other RAC nodes.

Can anyone tell me is BC a stand-alone proprietary system or can it be hosted by another provider??

@Have had a website built using BC by a website company that I have parted ways with
after 18 months of hell. I now have the BC platform and website, but have no idea
what I'm doing. They never activated the emails for me, but after tearing my hair out
I managed to get one email working, but just how is a total mystery.
Can anyone tell me if BC is a stand-alone proprietary system that is operated by Adobe
or can I get another Hosting company to take it over for me?? I would very much
appreciate someone's help before I go totally crazy. I can't get in touch with anyone to
talk to from Adobe - tried the Skype number several times and it never answered - I rang
it what was 9-5 US time, but no luck. Can't find a living person to talk to here in
Australia!!
HELP ME PLEASE.....

Hi
Adobe Business Catalyst is a hosted CMS. That means you need to host in ADOBES datacentre for the CMS to work.
But that's not all bad news because Adobe apply the updates for you so you're always running the latest software. AND the SSL certficates / DNS hosting etc etc etc is all included in your website.
The Business Catalyst is designed so website owners are connected with a partner. The partner helps to ensure you've got someone to lead on for support, or when something falls over. It's highly recommended to have access to a good partner. Sounds like you ended up with a dud.
So to answer your question directly. No, you can't just transfer your site to another hosting company.
BUT - you can transfer your site away from your existing Partner to someone else.
If you're in Australia I can offer you a really attractive wholesale solution with no costs to you and will help you transfer free of charge.
I can also offer you Business Catalyst training if you need this.
Let me know if you need help getting this all sorted
Brett Stockley
www.prettydigital.com.au
02 9212 4485

Can a inspire p5800 be used without a computer, as a stand alone speaker system

Can an Inspire P5800 be used as a stand alone speaker system? Here is my story. I just got this speaker system from my girlfriend who did not know that it had to be hooked up to a computer/soundcard etc... She thought it would just hook up to my MP3 player and be used as a speaker system downstairs in my shop. It looks like the decoder DDTS-100 could be bought and used as a stand alone sound adapter? Or is there a cheaper way? The only other way I can see is a triple headphone adapter that has one 1/8 inch plug going to three 1/8 inch jacks that can be fitted with a 1/8 inch plug to plug cable in each jack, then those going into the back of the subwoofer/connector area. Would that be a mono source that way? Any help would be appriciated. marc

I have set this system up with a creative zen vision m without using a computer just stand alown, but i have only been able to get the subwoofer, front left and right speaker to work. I dont know if that helps.

Can I configure Cisco 1602i (AIR-CAP1602I-T-K9) in Standalone mode ?

Hi everybody, please, i need some help here.
I bought 3 Cisco 1602i (AIR-CAP1602I-T-K9) but I didn't bought a Controller. How can I configure then in Standalone mode ?
I Saw in other forums, i need to change the IOS Software to an Autonomous Software. They suggested the ap1g2-k9w7-tar.152-4.JA1.tar. I would like to know if it is the right software and if there is any problem with licensing if i download and use it.
Explanation of the differences between AIR-CAP-1602i-x-K9 e AIR-SAP-1602i-x-K9
http://community.spiceworks.com/topic/448208-cisco-aironet-1602i-questions-issues
How to convert to IOS autonomous
http://www.experts-exchange.com/Networking/Wireless/Q_28245190.html
IOS Download:
http://software.cisco.com/download/release.html?mdfid=284366503&softwareid=280775090&release=15.2.4-JA1&flowid=37523
Thanks.
Wesley

Hi,
Yes you must need to change to autonomous mode.Yes it is the right software and you will not face any problem regarding license.
But for download the autonomous AP image from cisco you need a CCO (Cisco login) and valid service contract .
Here is the latest image:Can download from here
http://software.cisco.com/download/release.html?mdfid=284366503&flowid=37523&softwareid=284180979&release=15.2.4-JB5&relind=AVAILABLE&rellifecycle=ED&reltype=latest
How to covert from lAP to autonomous :
http://www.youtube.com/watch?v=QQ_NuxdRhQ4
http://rscciew.wordpress.com/2014/05/07/access-point-conversion-lap-to-aap-and-vice-versa/
Regards
Dont forget to rate helpful posts

Can WLC 4402 support AIR-CAP1602E-S-K9?

Hi
I had 1 end of life WLC 4402 controller. Can it support AIR-CAP1602E-S-K9 access point? If cannot, what is the supported access points for WLC 4402.
Thanks

Hi Steve
Thanks for the reply. Another question if i use the below access point with smartnet and configure as standalone AP. But in future if I want to configure to lightweight AP, can i request the firmware from CISCO TAC to flash the AP and make it lightweight? Thanks
AIR-SAP1602E-S-K9
802.11a/g/n Standalone AP, Ext Ant, S Reg Domain

AIR-CAP1602E-N-K9 access point

hi,
can any one help me to configure AIR-CAP1602E-N-K9 as standalone acess point.
its a new one with default setting as per my knowledege its a controller based access point so pls help how to convert into standalone access point and which image is compatible with that.

Converting a Lightweight Access Point Back to Autonomous Mode
You can convert an access point from lightweight mode back to autonomous mode by loading a Cisco IOS Release that supports autonomous mode (Cisco IOS release 12.3(7)JA or earlier). If the access point is associated to a controller, you can use the controller to load the Cisco IOS release. If the access point is not associated to a controller, you can load the Cisco IOS release using TFTP.
Note In some LWAPP deployments, the LWAPP controller resides between the access points and the rest of the network. In this topology, all traffic must cross over the controller before communication with network resources, such as a TFTP server, can occur. When converting back to non-LWAPP IOS with an access point that is no longer using the LWAPP protocol, traffic does not cross over the controller to reach the TFTP server.
Note The lightweight 1300 series access points can only be converted back to autonomous mode using a wireless LAN controller.
Using a Wireless LAN Controller to Return to a Previous Release
Follow these steps to revert from LWAPP mode to autonomous mode using a wireless LAN controller:
Step 1 Log into the CLI on the controller to which the access point is associated.
Step 2 Enter this command:
config ap tftp-downgrade tftp-server-ip-address filename access-point-name
Using a TFTP Server to Return to a Previous Release
Note This section does not apply to Cisco C3201WMIC and Cisco C3201LAP.
Follow these steps to revert from LWAPP mode to autonomous mode by loading a Cisco IOS release using a TFTP server:
Step 1 The static IP address of the PC on which your TFTP server software runs should be between 10.0.0.2 and 10.0.0.30.
Step 2 Make sure that the PC contains the access point image file (such as c1200-k9w7-tar.122-15.JA.tar for a 1200 series access point) in the TFTP server folder and that the TFTP server is activated.
Step 3 Set the timeout value on the TFTP server to 30 seconds.
Step 4 On the PC where the TFTP server is located, perform these steps:
a. Disable any software firewall products, such as Windows firewall, ZoneAlarm firewall, McAffee firewall, or others.
b. Ensure all Windows files are visible. From Windows Explorer, click Tools > Folder Options > View; then uncheck the Hide extensions for known file types check box.
Step 5 Rename the access point image file in the TFTP server folder to c1200-k9w7-tar.default for a 1200 series access point, c1130-k9w7-tar.default for an 1130 series access point, c1240-k9w7-tar.default for a 1240 series access point, and c1250-k9w7-tar.default for a 1250 series access point.
Step 6 Connect the PC to the access point using a Category 5 (CAT5) Ethernet cable.
Step 7 Disconnect power from the access point.
Step 8 Press and hold MODE while you reconnect power to the access point.
Step 9 Hold the MODE button until the status LED turns red (approximately 20 to 30 seconds) and then release.
Step 10 Wait until the access point reboots, as indicated by all LEDs turning green followed by the Status LED blinking green.
Step 11 After the access point reboots, reconfigure it using the GUI or the CLI.

Can AIR-CAP1602i-x-k9 be converted to stand alone??

Similar Messages

Maybe you are looking for