Can airport extreme extend the signal of my wifi network?

or this can only be done with airport expresses?? 
my house has real thick walls

Tesserax,
I have the 5th gen Time capsule, 1st gen airport extreme and airport express.
Up to now with lots of difficulties, I managed to setup Time capsule in a bridge mode.
(The only way was to have initial setup of TC without WAN cable connetcted)
Afterwards I extened my network with the airport express, but having problems with the extreme.
Setting up to extend the network from TC, after rebooting the extreme is not getting the right IP address from TC and it is not able to extend the network.
Any ideas?

Similar Messages

  • Can Airport Express extend the private and guest networks simultaneously?

    Can the Airport Express be used to extend the private and guest WiFi networks coming from the base station simultaneously, or can it only be an extension for one of the two at a given time?
    Joe

    Can the Airport Express be used to extend the private and guest WiFi networks coming from the base station simultaneously
    Yes, either by a wireless connection or Ethernet connection to the base station.....assuming that both the base station and extender are using firmware 7.6.3 or higher and AirPort Utility 6.3 is used to configure both AirPorts, which must be dual band models.

  • How do I add an Airport Express to extend the range of my WIFI network with my iMac as a base station?

    Hi people
    I need help to configure a new Airport Express only to extend the range of my WIFI network.
    My ethernet cable from modem is connected directly in my iMac and I am sharing the internet by WIFI inside home very fine.
    Now, I would like connect my devices on my garden on backyard.
    I can't move my iMac from their place and i just want add a Airport Express between the iMac and backyard to extend the range of WIFI.
    But I can't to configure to that. On Airport Utility appear the Airport Express connected directly to internet globe, but don't work.
    So, what can I do? What is wrong?
    Thanks all and best regards.
    Carlos Sgrillo, from Brazil.

    The AirPort cannot do what you ask.
    The Airport needs to connect to a modem, or another router......not to a computer.
    The Express can only extend a wireless signal that has been provided by another Apple router.

  • Can i use my airport to extend the range of my wireless network?

    I currently have a two wireless networks set up in my home. Network 1 is the wireless router provided by Verizon Fios. It has a stong signal in about half of my home. Network 2 -  I attached my airport to one of the LAN ports in the the back of the Fios router. I want to use my airport as a way to extend the range of my Fios wireless network. Is this possible?

    Network 2 can effectively "extend" Network 1 if the AirPort is permanently connected to the Fios router using an Ethernet connection.
    You would configure the AirPort to "create a wireless network" using exactly the same wireless network name, security settings and password as the Fios network. Additionally, the AirPort must be configured in Bridge Mode for this to work correctly.
    The most difficult part of doing this will be to find the exact type of wireless security that the Fios router is using and then find a corresponding compatible match on the AirPort. If the settings do not match up exactly, you'll have two networks which will require separate log ons.
    Configured correctly, your laptop will be able to "roam" from one area of the house to another and stay on the same network. That's why this type of setup is called a "roaming network".
    If you can locate the security settings for the Fios router and post back with that info, we can provide you with a step by step configuration for the AirPort if you need it.

  • Can AirPort Express extend the range of my Dlink

    Hi,
    Wonder if Airport Express would extend the wifi range of my Dlink wifi gateway and would actually work properly with it?
    Apreciate help ASAP!
    Dlink router: DVG-N5402SP Wifi Gateway ( Provided by ISP )

    The answer to the question is.....
    Yes, if you plan to connect the AirPort Express to the D-Link router permanently using an Ethernet cable.
    No, if you plan to have the AirPort Express connect wirelessly to the D-Link router.

  • Will airport express extend the range of our wifi?

    We have wifi through Comcast in our home.  The range, however, is at about 20 yds.  I exchanged the router that was supplied (monthly rental from) from Comcast without any change.  We have an Airport Express device, 802.11n, purchased in the last year in an effor to improve this, but was never connected as the instructions are beyond me.  I just tried to research it again, and I don't have a clue if it will help, and how to hook it up.  Help!

    An Apple AirPort Base Station can only "wirelessly extend" a wireless network created by another Apple AirPort Base Station.
    You can add the Express to your network as an additional wireless access point, as long as you connect it directly to the Comcast router with an Ethernet cable.
    This Apple Support document explains how to do that: Wi-Fi base stations: Setting up and configuring a roaming network (802.11 a/b/g/n)
    The AirPort Utility screenshots are outdated, but the wiring information shows the general arrangement you would require.
    Otherwise, you would need to purchase an additional Apple AirPort Base Station, connect it to the Comcast router, and use your Express to "wirelessly extend" the wireless network created by the new Apple AirPort.

  • I just moved and Time Warner gave me a new modem and router (Motorola surfboard 6580).  Can I now use my airport extreme in the bedroom to extend wireless signal?  If so, how?

    I just moved and Time Warner gave me a new modem and router (Motorola surfboard 6580).  Can I now use my airport extreme in the bedroom to extend wireless signal?  If so, how?

    Can I now use my airport extreme in the bedroom to extend wireless signal?
    Yes, if you plan to connect the AirPort Extreme back to the Motorola modem/router using a permanent wired Ethernet cable connection.
    No, if you were planning to have the AirPort Extreme extend the Motorola signal wirelesssly.

  • I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use?

    I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use? Essentially having two wifi connection off the same network? If so how do I set this up?

    Extending using a wireless connection always results in a performance compromise.
    If the Express is going to extend using a wireless connection, then the Express will need to be located about half way between the AirPort Extreme and the general area where you need more wireless coverage. The more that you have line-of-sight between the Extreme and Express, the better the network will operate.
    Remember......the Express can only "extend" the quality and signal speed that it receives, so it needs to be located where it can get a very good signal from the Extreme. Although Apple cleverly uses the term "extend", a more accurate term for the Express would be "repeater".
    If the Express will extend by connecting to the Extreme using a permanent, wired Ethernet cable connection......highly recommended for best performance.....then the Express can be located exactly where you need more wireless coverage. There is no signal loss at all through the Ethernet cable, so the Express gets a full speed signal no matter where it might be located.
    Post back to let us know which way to you want to go.

  • Can my Airport Express be used to extend the signal for an iPad2

    I am using a Linksys wired router as the beginning of my home network. There is an ethernet cable running from it through a wall to the Xbox 360 and an Airport Express serving as the base for the wireless network. I have an iBook on the other side of the wall and about 10 feet and an iMac about 20 feet with one wall in between. These two have some fluctuation in their signal but only between 4 bars and 3. I just got an iPad 2 and it is causing me grief because it struggles to maintain a connection just another 10 feet from the iBook. If I put it next to the iMac when it has full 4 bars the iPad gets maybe 2. The iPad has full bars if next to the router. That kind of defeats the purpose of buying an iPad. So, my question is how to rearrange the network so the iPad is happy in the living room where I mostly use it. I had considered moving the iMac and using it as a base station to free the Airport Express for other duty but where I want to move it is further away from the living room. Right now the Airport is wired to the router. Is this necessary for it to be a part of the network? I know I can use it to get music from iTunes to speakers but would that placement also work as a wireless extender? Would just buying another router for the Xbox location and putting the Airport there also be a better solution?

    ladybastet, let's clean up some terminology. You should designate only one router for your network. At present that is the Linksys. Your wireless access point is the Express, and it gets its network connection from the Linksys. Is that correct?
    If I put it next to the iMac when it has full 4 bars the iPad gets maybe 2. The iPad has full bars if next to the router.
    Now that you know your Linksys is the router, is the above correct? Unless the Linksys is also a wireless access point, the iPad's proximity to it will not matter. Only its proximity to the device creating the wireless network is a factor. In your case, I believe that is the Express.
    There is an ethernet cable running from it through a wall to the Xbox 360 and an Airport Express serving as the base for the wireless network.
    I'm not sure I understand. Is one Ethernet cable going to two places? What is it connected to, precisely?
    Right now the Airport is wired to the router. Is this necessary for it to be a part of the network?
    In the case of a wired router, yes.
    I'm wondering if you have things configured properly, particularly if you have configured the iMac to share its network connection over AirPort. I'm even wondering if your iPad has unintentionally joined a neighbor's wireless network.
    I had considered moving the iMac and using it as a base station to free the Airport Express for other duty but where I want to move it is further away from the living room.
    Using the iMac to share a wired Ethernet connection to create its own wireless network is certainly possible, but it is less than ideal. For one, the iMac would have to be powered on all the time.
    You do not need or want another router.
    It is impossible for me to be certain of your network environment (meaning, the size and configuration of your home, the proximity of competing wireless networks, the number of network devices, and the potential for interference) but you might be better off replacing the wired Linksys router with an AirPort Extreme. That would give you the ability to create a "roaming network" or to use your Express to extend the Extreme's wireless network. I think this would be the easiest solution, but given the uncertainly of your description this expense may not be necessary.
    Much of my confusion stems from your original question: "Can my Airport Express be used to extend the signal for an iPad2" - the quick answer is yes, but a prerequisite question is, "what signal?" The only "signal" I can determine that may be relevant is the one created by the Express. Once we have the terminology fixed, perhaps we can fix what's wrong with your network.

  • Can AirPort Extreme be used as a signal extender?

    Can AirPort Extreme be used as a wireless extender, wi fi booster?

    If you are planning to "extend" wirelessly......the AirPort Extreme will "extend" the wireless signal from another Apple wireless router....but....it will not "extend" the wireless signal from a 3rd party router.

  • I have Airport Extreme as the base unit and an Express unit in a room separated by a brick wall to improve signal. Express shows a green light indicating signal but my iPad does not perform well. How can I improve other than hardwire ethernet connection?

    I have Airport Extreme as the base unit and an Express unit in a room separated by a brick wall to improve signal. Express shows a green light indicating signal but my iPad does not perform well. How can I improve other than hardwire ethernet connection?

    Other suggestions, and more info about the nature of the problem, may be in this Apple tech note.
    http://support.apple.com/kb/HT1365
    For example, you might find that the brick wall is not the only problem. There may be other devices pumping out enough wireless interference to be making things even worse.
    I agree with Bob Timmons that Ethernet is best and most reliable. And that powerline (which I use) is easier and potentially faster than wireless...but only if your power lines do not have electrical devices plugged in which produce electrical noise on the line. Powerline will be slower than Gigabit Ethernet.
    Ethernet cable is the only way to ensure that the signal goes directly there in a shielded way for a clear fast signal. Wireless and powerline are much slower because of all the other things the signal has to fight past to get to the other device.

  • Can Airport extreme be used as a repeater from the BT home hub

    can Airport extreme be used as a repeater from the BT home hub because my laptop will be very far away and i currently get a rubbish signal on my Windows pc so when i upgrade to the mac pro i am wonderimg if i could use the airport extreme as a repeater to strenthen my already rubbish signal??

    You might want to check with BT to see if they have a device to do what you want.
    Using wireless only, the AirPort Extreme will only "extend" or "repeat" the wireless signal if it has been produced by another Apple router. It is not compatible with routers from other suppliers for this purpose.

  • Which airport is good to extend my wifi, what is the difference between the AirPort Extreme and the airport express base sstation

    What is the difference between the AirPort Extreme and the airport express base station and which one can extend my wifi router.

    With rare exceptions of a few older routers, neither one can extend a non-Apple router's network wirelessly - they are not designed that way - but you can extend the wireless network if the Extreme is hardwired to the router or you can connect wirelessly and join the network as an access point that will provide remote ethernet access but not produce or extend the wireless signal - here is a comparison of the Apple base stations - http://www.apple.com/wifi/

  • Slow WiFi transmission and low signal power (Airport Extreme extended by Airport Express)

    I am experiencing slow wifi transmission between my notebooks and my base stations and I am hoping someone can help me fix it.
    My wifi configuration is the following:
    1 Airport Extreme base station (acting as router, wifi "creator" and DHCP server)
    1 Airport Express base station (connected to Airport Extreme with a LAN cable, set up to extend wireless network)
    1 Lenovo T410 notebook with Intel Centrino Ultimate N-6300 AGN WiFi antenna (I will call this one "Lenovo"), connected to wireless network, running Windows 7
    1 MacBook Pro purchased in 2009 (I will call this one "Mac"), connected to wireless network, running Mac OS X Lion
    1 QNAP T209-II NAS, connected to Airport Extreme via UTP cable
    Airport Extreme (AXTRM) is creating a 802.11n wireless network with WPA2+PSK security with MAC address filtering. The other base station, Airport Express (AXPRS) is connected to AXTRM via a UTP cable. AXPRS is set to extend my wireless network.
    My first problem is low signal power. My appartment is 90m2 in size and is in one floor. It is a new flat with high ceiling and modern layout, meaning little walls, big rooms and wide corridors. Still my notebooks, iPhones and iPad can barely reach AXTRM when I am on the other side of the flat. This was the reason why I purchased AXPRS and placed it in the middle of the appartment. My notebooks are placed just on the other side of the AXPRS's wall (less than 1 meter of distance and a simple 10cm brick wall in between), yet signal strength is only at about 80% (measured on my Lenovo using Lenovo Access Connections tool).
    My first question is: Is it normal that in a 90m2 flat with not unusual obstacles, I need 2 base stations and even then have a rather poor reception?
    My second problem is even more disturbing. I think I have catastrophic transfer speeds via wLAN. It takes over 1 hour to transfer cca. 1GB of files (average size 8MB) from my Lenovo or Mac to my QNAP. My Lenovo is showing about 250kb/s transfer rate when copying files. At the same time, Windows 7 show connection speed 144Mbps. This mean about 18MB/s. I know these numbers are theoretical and that actual transfer speeds are lower. But hey, 72 times lower? Furthermore, if I copy files from my Mac and my Lenovo at the same time, transfer speed is slightly lower. On the other hand, if I connect my notebooks to AXTRM via LAN cable and copy files to QNAP, transfer speeds are a few megabytes per second.
    To make things even more confusing for me: if I transfer files from the internet, I get download speed at about 700kb/s, which is quite in line with my internet download speed. I don't understand why transfer speeds within my local network are so much lower.
    Therefore, my second question is: How to set up my base stations and my routers to get a decent wifi connection?
    I hope someone could help me. If you need any more information, just ask. Thanks!

    From my experience of setting up the Airport WiFi for family members and friends, I have learnt the following :-
    1. Airport Express is not as good as Airport Extreme, for being as extender, the difference can be quite a lot.
    2. There is always a dead cornor (bad reception) in a house
    3. Even moving the Airport Extreme / AE a few inches, the performance can be improved quite significant
    4. If possible, always choose 5G 802.11n than 2.4G, unless there are many thick walls.
    My suggestion will be as follows :
    1. Moving out the AEBS out of a closet, is a good idea
    2. Always try to locate the AEBS in the centre of a area, instead of the two sides
    3. Try to test the AEBS without an extender, and find the best location area (don't place on the floor, neither above 6 feet height)
    4. After finding a best location, set the extender closer to the AEBS, and then moving apart from it (check the performance after every move), it is better that both devices can face each other.
    5. I can't tell you the reason, and some people may not agree with me, the new 2013 Airport Exteme performance is better and may be is a good idea to replace your Airport Express, and use it to connect with your router, and old AEBS as an extender
    6. Some Powerlinks (in case you can't use a wired ethernet connection between the two devices) work and some don't work with Apple Airport products, therefore, if possible, have an option to return them to the shop if they do not match
    Good luck

  • Can I use an American Airport Extreme in the UK?

    Hi guys,
    I bought an Airport Extreme in the US sometime ago. I never managed to get it to work and gave up. My Wireless has gone down so I thought I would give it another go. Still can't get it to work.
    Will a USA airport extreme work in UK?
    I have updated firmware to version 7.4.2
    The big issue I think is on the wireless options page I can only select America, Canada or a bunch of South American counties. Do the US have different wifi signals to UK?
    Is there anyway of over writing the firmware with UK firmware?
    Is it not any of the above and maybe I am just setting it up wrong?
    Please help,
    thanks.
    Jamie

    Welcome to the discussions!
    +Will a USA airport extreme work in UK?+
    Yes
    +Do the US have different wifi signals to UK?+
    Yes. UK uses channels 1-13. US uses 1-11. You won't be able to use 12 and 13 on your AirPort Extreme. I'm not sure about 5 GHz channels if you plan to use that frequency.
    +Is there anyway of over writing the firmware with UK firmware?+
    No
    +maybe I am just setting it up wrong?+
    If you can tell us what modem (make and model number) you are using with the AirPort Extreme, we may be able to help with the setup.

Maybe you are looking for

  • Unable to delete the files from CSV volumes on HyperV Cluster

    Hello There, I have a HyperV failover cluster with CSV Volumes recently i moved some of the VMs to another cluster. VMs are moved but i still have the VM files on the CSV volumes which are occupying the disk space i tried to delete the VHD files / VM

  • HT1926 Where does iTunesSetup.exe go when I save it?

    I have repeatedly tried to download iTunesSetup.exe so that I can install an update of iTunes.  Everytime I save it, no matter what the location, it does not appear there.  I have set the view to show hidden files, but it still does not appear.  Wher

  • Mapping to leads vs. straight to opportunities

    client doesn't really convert leads to opportunities, its more opportunity to quote to order (and quote/order are done in external application). I'm thinking the functionality around leads such as qualify, convert, archive, reject is overkill and to

  • IMovie 11 can't see my videos/pictures.

    I recently purchased an external harddrive. I then moved all my video and picture files to that drive, hoping I did it properly and actually grabbed all my video and pictures. Now that I start up iMovie, I don't see all the footage I had before. I al

  • Downgrade probs with desktop mgr: app loader retrieves old version files thru internet

    really this is for desktop mgr 4.6 and 4.7 but i could not write to thread some time ago i purchased documents to go premium. unfortunately at first dataviz was insiting it would only be available OTA, after install, and later after os upgrade to pat