Can cisco MSE(mobility service engine) configured to work with non-cisco access points?

I understand that access points can be configured to forwards all the probe requests to cisco wifi controller. cisco MSE(mobility service engine) gets the probes from wifi controller to find the location of the mobile devices.
My question, can cisco MSE(mobility service engine) be configured to work with non-cisco access points?

No and the reason why is the NMSP communication from the MSE to the WLC. Other vendors don't support this so there is no communication happening.
-Scott

Similar Messages

  • Cisco Aironet FW 15.2 Does not work with Non-Cisco Media Bridges

    I have a Cisco Aironet 1142i that was just updated from 12.4(23c)JY to 15.2(4)JA1 (don’t think model matters as the issue seem to be the firmware) and now I cannot get my media bridges (3 different ones) to either connect to the 1142 AP or obtain and pass the DHCP addresses to other device connected to the built in switch. If I reload the 1142 AP firmware to 12.4, than this works fine. I have not seen anything in the release notes that changed how this works or if there is I could not find it.
    Does anyone know why this changed and if there is any settings that I need to enabled / disable?
    Any help on this would be greatly appreciated

    More info to add to this.
    AIR-AP1142N-A-K9 Hardware Version of v06 works with firmware 15.2.
    AIR-AP1142N-A-K9 Hardware Version v05 does not work with firmware 15.2, but will when downgraded to firmware 12.4.
    I'm also having this issue with Cisco Aironet 3602 Fw 15.2(2)JB and 3502 Fw 15.2(2)JB$ that's on a Cisco 2500 WLAN Controller Sw Ver. 7.4.100.0.
    Any help on this would be greatly appreciated

  • ISE ( Idendity Service Engine ) & MSE (Mobility Service Engine ) & Prime Infra

    What is the difference between ISE ( Idendity Service Engine ) & MSE (Mobility Service Engine ) & Prime Infra .
    How this will be used along with WLC & AP & wireless Users.

    The Cisco Identity Services Engine (ISE) is an all-in-one enterprise policy control product that enables comprehensive secure wired, wireless, and VPN access, leading to more productive workers and lower operations costs. When operating in a network, ISE provides the following key features: 1.Rigorous identity enforcement 2. Extensive policy enforcement 3.
    Security compliance 4. Automated onboarding whereas Cisco Mobility Services Engine supports RTLS and WIPS and Cisco Prime is centralize wireless and wired Monitoring and management solution. ISE and MSE both can be integrated with Cisco Prime. For more deatil over these products you can see the below links.
    http://www.cisco.com/en/US/prod/netmgtsw/prime.html
    http://www.cisco.com/en/US/prod/collateral/wireless/ps9733/ps9742/data_sheet_c78-475378.html
    http://www.cisco.com/en/US/prod/collateral/vpndevc/ps5712/ps11637/ps11195/data_sheet_c78-656174.html

  • Can the WCC mobile app (iOS and Android) work with an SSO protected content server?

    We have just configured Single Sign On with Oracle Access Manager for our WebCenter Content server (and also for the WCC ADF UI). Everything works fine, even the Desktop Integration, except that now we cannot connect anymore from the WCC mobile apps.
    Is there a solution or is it really not possible to combine mobile access with SSO?

    I just found the solution:
    Add the following resource (type: excluded) to the wcc application domain in OAM:
    /cs/idcplg/**

  • Auto Smartports with non-Cisco devices

                       I have used auto smartports in the past and have been successful creating macros that use mac-addresses.
    My question is can I create a macro that works with non-Cisco devices that are CDP capable? 
    We have Motorolla access points that use CDP and I would like to use auto smartports to put them on their own VLANs.
    Can it be done using CDP?  What version of the IOS would I need to be on?  Currently the 3750-Xs are on 12.2.(55).
    Are there any guides or configuration examples?  I've searched but have been unsuccessful in find anything so far.
    I have seen some articles that reference device sensors and device profiles, but have no idea where to begin.
    Thanks in advance for your support.

    You may need to create a Cisco TAC case for this.
    If not, then move this thread to the EEM section.  If the Moto AP supports CDP then you can get someone (like Joe Clark) to build a small EEM script.
    EEM is supported up to the 3560/3750.

  • Mobility Service Engine 7.4.100.0 ova WEB Services problem

    Hello,
    We have sucessfully installed MSE-VA-7-4-100-0.ova file in our Lab, and after installation we can't open https session with MSE.
    When we type <https://mymseipaddress> we are getting these message:
    Error 404 - Not Found.
    No service matched or handled this  request.
    Known services are:
    http://my server:8880/hs/
    http://my server:8880/mdp/
    http://my server:8880/admin/
    http://my server:8880/wips/
    http://my server:8880/location/
    http://my server:8880/subscription/
    http://my server:8880/aaa/
    http://127.0.0.1:8180/localadmin/
    https://127.0.0.1:8443/localadmin/
    https://my server:8843/mdp/
    https://my server:8843/wips/
    https://my server:8843/hs/
    https://my server:8843/admin/
    https://my server:8843/location/
    https://my server:8843/subscription/
    https://my server:8843/aaa/
    We are able to import MSE to Cisco Prime Infrastructure 1.3 and we have communication with WLC. We have tried proposed solution explained in link below:
    https://supportforums.cisco.com/message/3656441#3656441
    but we are are unable to import server certificate  becouse our certificate vallidation is falling. We don't know how we should append private key to the signed certificate in order to get our MSE web services up and running.
    Any help in solving this problem would be much appreciated.
    Regards,
    Jelena

    Here is the output from getserverinfo:
    [root@MDS-MSE-LAB ~]# getserverinfo
    Health Monitor is running
    Starting MSE Platform, Waiting to check the status.
    MSE services are up, getting the status
    Server Config
    Product name: Cisco Mobility Service Engine
    Version: 7.4.100.0
    Health Monitor Ip Address: 1.1.1.1
    High Availability Role: 1
    Hw Version: V01
    Hw Product Identifier: AIR-MSE-VA-K9
    Hw Serial Number: MDS-MSE-LAB.mds.rs_3287d770-825b-11e2-8bd8-00505692612a
    Use HTTP: false
    Legacy HTTPS: false
    Legacy Port: 8001
    Log Modules: -1
    Log Level: INFO
    Days to keep events: 2
    Session timeout in mins: 30
    DB backup in days: 2
    Services
    Service Name: Context Aware Service
    Service Version: 7.4.0.38
    Admin Status: Enabled
    Operation Status: Up
    Service Name: WIPS
    Service Version: 1.0.4041.0
    Admin Status: Disabled
    Operation Status: Down
    Service Name: Mobile Concierge Service
    Service Version: 2.0.0.37
    Admin Status: Enabled
    Operation Status: Up
    Service Name: Location Analytics Service
    Service Version: 1.0.0.12
    Admin Status: Enabled
    Operation Status: Up
    Server Monitor
    Server start time: Fri Mar 01 15:59:43 CET 2013
    Server current time: Mon Mar 04 09:39:45 CET 2013
    Server timezone: Europe/Ljubljana
    Server timezone offset: 3600000
    Restarts: 6
    Used Memory (bytes): 66655704
    Allocated Memory (bytes): 133169152
    Max Memory (bytes): 477233152
    DB virtual memory (kbytes): 0
    DB virtual memory limit (bytes): 0
    DB disk memory (bytes): 2137466496
    DB free size (kbytes): 0
    Active Sessions
    Session ID: 16978
    Session User ID: 1
    Session IP Address: 10.13.7.15
    Session start time: Mon Mar 04 09:38:17 CET 2013
    Session last access time: Mon Mar 04 09:38:19 CET 2013
    Default Trap Destinations
    Trap Destination - 1
    IP Address: 10.13.7.5
    Last Updated: Fri Mar 01 11:43:04 CET 2013
    Context Aware Service
    Total Active Elements(Wireless Clients, Tags, Rogue APs, Rogue Clients, Interferers, Wired Clients): 25
    Active Wireless Clients: 13
    Active Tags: 0
    Active Rogue APs: 11
    Active Rogue Clients: 1
    Active Interferers: 0
    Active Wired Clients: 0
    Active Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired Clients, Tags) Limit: 100
    Active Sessions: 1
    Wireless Clients Not Tracked due to the limiting: 0
    Tags Not Tracked due to the limiting: 0
    Rogue APs Not Tracked due to the limiting: 0
    Rogue Clients Not Tracked due to the limiting: 0
    Interferers Not Tracked due to the limiting: 0
    Wired Clients Not Tracked due to the limiting: 0
    Total Elements(Wireless Clients, Rogue APs, Rogue Clients, Interferers, Wired Clients) Not Tracked due to the limiting: 0
    Context Aware Sub Services
    Subservice Name: Aeroscout Tag Engine
    Admin Status: Disabled
    Operation Status: Down
    Subservice Name: Cisco Tag Engine
    Admin Status: Enabled
    Operation Status: Up
    Regards,
    Jelena

  • Mobility Service Enginer & WCS required or not?

    Hi,
    I have Cisco Wireless Lan Controller 5508 with 35 (3600 Series Access Points.  Do i need to purchase Mobility Service Engine for this or no need?  Do i need WCS server for this or no need?
    Thanks,

    The WCS/NCS/Prime and MSE are optional devices that you don't need to get your wireless up and running. So no, you don't need to purchase those devices unless you want the features those devices will provide you. These features are listed in the data sheet.
    Sent from Cisco Technical Support iPhone App

  • Need some help getting started with Mobility Services Engine

    Someone has ordered several 3602 access points, a 5508 controller, and a MSE 3310 for one of our remote locations. The access points and controller are in place and are working fine (we use lightweight APs at many other locations), but I'm not sure how to approach the MSE. I've gone through the set up, and it's onsite, on the network, and I've added it to our WCS server. It's got a 2000 user context-aware services license. But I'm not sure where to go from here. It doesn't seem to actually be doing much of anything. Is there some quick start guide as to where to go from this point? The wireless users are mostly mini netbooks and iPads.

    Well, I'm no expert, but I did spend the night...
    Ok.  In the WCS on the Services tab, Mobility Services, your MSE is recognized and reachable with matching SW Versions.
    So, on the home tab, ContextAware tab, you see your MSE and it is showing Zero's  for data in most if not all fields?
    Back to the Services tab, Synchronize Services...  is this empty?
    The MSE can only 'SEE' what you tell it to 'LOOK' at.  That is, buildings and floor areas.  I haven't tried just a building.
    Check the left hand box for all the floor areas of interest.  Scroll to the bottom an slect 'Change MSE Assignment"
    select which (of the many or the one) MSE you wish to have monitor the area.  Check the 'CAS' box and save.
    Up on the upper levt is a Synchronization block..  push the Synchronize button and sit back..
    All MSE data is presented only to the WCS (or Pi).
    Good Luck
    David

  • Can WAE be integrated with non-cisco devices?

    So far, all documentation that I read, WAE is used in conjunction with Cisco devices.  Can WAE be integrated with non-cisco devices? 
    I guess, In-line mode should work ok, but how about off-path mode?  An example or link will be appreciated.
    Thanks!
    Joe

    Hi Joe,
    It should be possible to use WAAS with non-cisco routers, as long as they support WCCP.
    There are no documents on this because, the configuration from WAAS point of view would be the same, and the router configuration would depend on the vendor.
    Regards
    Daniel

  • Interconnecting cisco switches with non-cisco switches

    I need help concerning interconnecting two Cisco switches (3550’s) using a non-Cisco switch or hub on the LAN. I have noticed that the two Cisco switches connected using a non-Cisco switch are able to communicate well, however a PC connected to the non-Cisco switch/hub can not ping any device on the LAN. The non-Cisco device is a working one. When the two Cisco switches are connected using a Cisco switch, PCs connected to the interconnecting switch are able to ping. What’s the explanation? Please help.

    Building configuration...
    Current configuration : 3342 bytes
    ! No configuration change since last restart
    version 12.1
    no service pad
    service timestamps debug uptime
    service timestamps log uptime
    no service password-encryption
    clock timezone GMT -2
    ip subnet-zero
    ip rcmd rcp-enable
    ip rcmd remote-username cwuser
    spanning-tree mode pvst
    spanning-tree extend system-id
    interface FastEthernet0/1
    switchport mode dynamic desirable
    interface FastEthernet0/2
    switchport mode dynamic desirable
    interface FastEthernet0/3
    switchport mode dynamic desirable
    interface FastEthernet0/4
    switchport mode dynamic desirable
    interface FastEthernet0/5
    switchport mode dynamic desirable
    interface FastEthernet0/6
    switchport mode dynamic desirable
    interface FastEthernet0/7
    switchport mode dynamic desirable
    interface FastEthernet0/8
    switchport mode dynamic desirable
    interface FastEthernet0/9
    switchport mode dynamic desirable
    interface FastEthernet0/10
    switchport mode dynamic desirable
    interface FastEthernet0/11
    switchport mode dynamic desirable
    interface FastEthernet0/12
    switchport mode dynamic desirable
    interface FastEthernet0/13
    switchport mode dynamic desirable
    interface FastEthernet0/14
    switchport mode dynamic desirable
    interface FastEthernet0/15
    switchport mode dynamic desirable
    interface FastEthernet0/16
    switchport mode dynamic desirable
    interface FastEthernet0/17
    switchport mode dynamic desirable
    interface FastEthernet0/18
    switchport mode dynamic desirable
    interface FastEthernet0/19
    switchport mode dynamic desirable
    interface FastEthernet0/20
    switchport mode dynamic desirable
    interface FastEthernet0/21
    switchport mode dynamic desirable
    interface FastEthernet0/22
    switchport mode dynamic desirable
    interface FastEthernet0/23
    switchport mode dynamic desirable
    interface FastEthernet0/24
    switchport mode dynamic desirable
    interface GigabitEthernet0/1
    switchport mode dynamic desirable
    interface GigabitEthernet0/2
    switchport mode dynamic desirable
    interface Vlan1
    ip address
    ip default-gateway
    ip classless
    ip http server
    snmp-server community
    snmp-server community
    snmp-server location
    snmp-server system-shutdown
    snmp-server enable traps snmp authentication warmstart linkdown linkup coldstart
    snmp-server enable traps config
    snmp-server enable traps entity
    snmp-server enable traps flash insertion removal
    snmp-server enable traps bridge
    snmp-server enable traps stpx
    snmp-server enable traps rtr
    snmp-server enable traps port-security
    snmp-server enable traps vtp
    snmp-server enable traps vlancreate
    snmp-server enable traps vlandelete
    snmp-server enable traps envmon fan shutdown supply temperature status
    snmp-server enable traps MAC-Notification
    snmp-server enable traps hsrp
    snmp-server enable traps cluster
    snmp-server enable traps copy-config
    snmp-server enable traps syslog
    snmp-server enable traps vlan-membership
    line con 0
    line vty 0 4
    login
    line vty 5 15
    login
    ntp clock-period 17180064
    end

  • I bought the external DVD player/burner for my Macbook.  I tried using it with my Dell laptop but it will not work.  Is it not configured to work with anything but apple operating systems?

    I bought the external DVD player/burner for my Macbook.  I tried using it with my Dell laptop but it will not work.  Is it not configured to work with anything but apple operating systems?

    If you purchased the Apple USB SuperDrive, it will only work with select Apple devices. It won't work, for example, on my Late 2011 model that has a SuperDrive built-in, but it will work with an Air, Retina model, new 'drive-less' iMacs, etc.
    As far as I know, though, you can only hack the drive to work with some other Apple devices, but not with Windows PCs. Which is a shame as other, less expensive DVD/CD devices will work with just about any machine.
    Sorry,
    Clinton

  • HT1218 How can I make my first generation AirPort Express work with Mountain Lion? I have a 13" MacBook Pro (non-retina).

    How can I make my first generation AirPort Express work with Mountain Lion? I have a 13" MacBook Pro (non-retina).

    Hi guys, recently had the same issue. You require an older version of Airport Utility to configure the older Airport Express. It can be found here.
    http://www.google.com/url?sa=t&rct=j&q=airport%20utility%205.6%20for%20lion&sour ce=web&cd=1&ved=0CFMQFjAA&url=http%3A%2F%2Fsupport.apple.com%2Fkb%2FDL1482&ei=Ip MBUPLwLoq42wW4puXMBA&usg=AFQjCNGOFUPMM0ZjsKeyj5CcL2oe9Eaf7A

  • Recovery and Applications CD not configured to work with this machine.

    Satellite A215-S4757
    Machine trashed due to virus and want to reset to original configuration.  Using disk 1 of 2 labeled RECOVERY AND APPLICATIONS/DRIVERS SATELLITE A210/215 SERIES WINDOWS VISTA HOME PREMIUM 32 BIT.  When the CD boots an error is displayed.  The error reads:
    "This Recovery and Applications CD is not configured to work with this machine (*).
    This CD is for: Satellite A215, Satellite A210
    Please use the correct Recovery and Applications CD."
    Can you tell me why this is not recognizing the machine correctly?  Thanks for the help.
    R/Jim

    Satellite A215-S4757 
    You need the utility which resets the DMI string for that model. Call Toshiba tech support at 800-457-7777.
    -Jerry

  • NAC with NON-cisco wireless

    Hi there,
    I know that with WLC 5.1 and NAC 4.5 Cisco started to support OOB, NAC implementation. Now here is my question:
    A customer has CISCO environment except for the wireless which is another vendor. What are the options to bring wireless traffic into NAC server? Is OOB deployment possible?
    Thanks,
    rdianat

    So what is the solution for this scenario?
    remote site has non-cisco autonomous wireless AP. NAC is centralized. I can not use OOB since there is no support for non-cisco AP in OOB mode. As a result I use InBand mode. This means that local wireless trffic in remote site must travel to central site, go through NAC Server and go back to remote site. Is this correct?

  • How can I get my hp Laserjet 1012 to work with Windows 7?

    How can I get my hp Laserjet 1012 to work with Windows 7?

    Here is a list of products that are not supported in the win7 OS. This product is listed there.
    Products not supported in win7
    I am an HP employee.
    Say Thanks by clicking the Kudos Star in the post that helped you.
    Please mark the post that solves your problem as Accepted Solution

Maybe you are looking for