Can connect to WLAN, but can't access any web site...

I have a Nokia E61 that I have configured to access my wirless home network (Linksys). I use personal WPA security, and my SSID is hidden. I loaded the proper settings into an access point setting and when I go to Web, the phone shows that it connects to my Linksys router, but the web page never loads. I eventually get a time out error. If I connect to the same website using GPRS, it loads without any problem.
Any ideas?

Thanks for the reply!
I have looked at my RV082's firewall setup, but don't see anything out of the ordinary. I even disabled the firewall, but it didn't seem to make any difference. What did you have in mind that I should check?
I get the following error on the E61 when I try to access an Internet website: "Web: Connection Time Out". It takes about a minute or two for the E61 to generate that error.
Regarding the RV082's ability to assign devices to the right subnet, I have three other PCs on my network (2x Windows XP, 1x Windows 98SE), and they have always connected the first time and every time with no issue. How would I check which subnet the RV082 is assigning to the phone? On a PC, I usually do an "ipconfig /all" at the command line and see what's assigned. Is there an equivalent command for the E61 that I could enter while I'm connected?
If I remove the RV082 and plug my WAP54G directly into my cable modem, then my E61 can access the Internet. So it's definitely an incompatiblity with the settings in the RV082 and the E61. But before I/we blame the RV082, I have more or less the same problem at my employer's office: I can connect to the office network, but can't access any sites outside the company network. The only difference is the E61's error message: at work I get a "no gateway response" error within a few seconds. It's a company with around 200 employees at that site, and we're certainly not using an RV082 in the office. I have not tried to call Linksys support yet because in fairness to them, they won't know jack s*** about the E61 and how to configure/check the settings.
Is there something about the DNS settings in the E61 that I'm setting incorrectly? I have them set to Automatic in both IPv4 and IPv6 settings, which is how my PCs are setup at home and what my IT guy at work tells me should be OK.
Thanks in advance for any more advice!
BTW, I'm no big fan of Linkys either, but I've had zero problems with my Linksys products. Also, when I have had to contact Linksys for help with a setup, they have always eventually come through and solved the problem. I've tried contacting Nokia and can't even get a live person that can do anything (the E61 isn't supported by Nokia USA, and the UK phone number they gave me was just a recording). If anything, I'm ready to hurl my E61 through the window right now as I've spent way too many hours trying to get this thing to work.
hk

Similar Messages

I bought my ipad mini in the UK and it worked fine, I live in Cyprus and since being back i can not access any web sites

My web browser( Google ) home page appears but when i type in the web address it does not access them it just constantly appears to be loading.
Any help would be appreciated
Thanks

there are a lot of complaints here about wifi issues with the ipad mini - all seam to deal with 3rd party routers. you might want to check these Threads out.
did you delete the wifi network on your ipad and reconnect? Are you using WPA2? Did you select TKIP/AES or only one of them? Does your ipad get an ip address?

Can only access one web site

I can only access one web site . www.cisco.com. I am connected to the internet via a lynksys DSL Router, I am using dhcp and NAT from the Lynksys note:works fine for 3 other windows based pc's.
when I try to connect to any other site the page Hangs during load and neve displays.
I can ping all of the web sites that do not come up
I am using a SunBlade 100 and did a new install. I tried the install with webstart and had the same result during the install. again I can only open sucessfully www.cisco.com.

Hello!
I am getting this error, but the above fix does not solve the issue, however I do know what has caused it.
I have an edmx file in a WCF webservice which feeds a silverlight app. The edmx is quite complex and a bit fragile, but was working fine up until I introduced our Industry Codes view into the model. The view is basically { ID, ParentID, Name, ... }. In my model I have created an association to itself which describes Children(*)/Parent(0/1) so I have a nice and tidy hierarchical structure. The edmx and the service build without any errors - hurrah! However, when I update the service reference I then get the below error (and a whole load of others as none of the webservice objects exist anymore):
Error 21 Custom tool error: Failed to generate code for the service reference 'WCF_ContactAdmin'. Please check other error and warning messages for details. X:\2008-054 ContactAdmin_Silverlight\Contact2_Admin_Silverlight\Service References\WCF_ContactAdmin\Reference.svcmap 1 1 Contact2_Admin_Silverlight
When I try the fix mentioned in the link above this error disappears, but then so do all the objects in the datamodel, so I cannot continue from there.
Having the hierarchical data objects defined in the EDM will make like so much easier in future, any help will be greatly appreciated, thank you!!
Tim
Web Developer at Terrapinn

Can't access some web sites with safari

Can't access financial web site since time before last of safari update. Any help?

In my original post, not today's, I had said I was having the issues on the Mini, running OSX 10.6.8 and Safari v.5.1.5 for my bank's pill pay. I should have been more specific as to which machine and OSX Safari browser I'm having the T-Mobile problem with. My mistake.
It is on both the MacMini and now the Air too. A moment ago, I was able to log in to my.t-mobile.com on the Air, but after putting into my Bookmarks folder, I can't do it anymore. The Log in button comes up greyed out instead of green.
I'm also still having trouble with my bank's bill pay section on both computers too.
I wonder if it's related to the saving of the log in info or putting in the Bookmark Folder?

Palm TX can connect but can't get any web sites

Hi,
I was just able to get my Pam TX to connect to my home network, by manually entering the IP address. Now it instantly says "cannot find requested page" as soon as I enter any web address. Am I missing something?
Is there something I need to upgrade? I have a Verizon FiOS router, WEP connection...
Many thanks,
HA
This question was solved.
View Solution.

Instead of entering the name of the PC, try entering the IP address for it on your network.
I strongly suggest setting "static IP's" for both your TX and PC in your router. This will ensure better success of connection for a wifi HotSync.
WyreNut
I am a Volunteer here, not employed by HP.
You too can become an HP Expert! Details HERE!
If my post has helped you, click the Kudos Thumbs up!
If it solved your issue, Click the "Accept as Solution" button so others can benefit from the question you asked!

Can't access the web-site in my home folder from the internet. Need help.

I am trying to publish a website from the Sites folder in my home directory. The website is made and I can access it from from every computer within my ethernet. But despite a couple attempts I made I can not get the website published on the internet.
I have an Airport Express station. Two Macs and one PC are using the ethernet. As far as I can tell the Airport Express station is directly connected to the internet. I live in a brand new apartment which has Lan outlets in every room next to the electricity outlets. I have a single designated internet IP address.
To open my computer to the internet I set the "Default Host Option" in the Airport Administrator Utility and selected the default three digits for the "Default Host option" IP address. Then I updated the Airport Express station, manually set the IP address in the Network preferences on my Mac to the "Default Host option" IP address and activated Personal Web Sharing in the Sharing preferences. By doing so I lost my internet connection. It turned out I still had the same IP address that I had before I selected Default Host Option.
As I understand with the Default Host Option I designate one IP address within the ethernet to receive all traffic from outside. But how do you now tell the Airport Express station which computer on the ethernet will be the host for the incoming traffic carrying the Default Host Option IP address? Apparently just setting the IP address manually in the clients computer Network preferences to the "Default Host Option" IP address doesn't tell the Airport Express station to change the IP address it has assigned to this client to the Default Host Option IP address.
In another attempt to make my website accessible on the internet I removed the Default Host Option and instead opened Public Port 80 and Private Port 80 for the IP address of the client computer in the Port Mapping tap of the Airport Administrator Utility. But again, no access to my website from the internet.
To access the website from within the ethernet I use the following web-link, which works fine:
http://192.xxx.x.x/~user/index.html
The internet of course doesn't see the 193 IP address. It only sees the Public IP address. Therefore I used the Public address instead of the Private IP address to connect to my website from the internet:
http://222.xxx.xxx.xxx/~user/index.html
But as I said, I still can't access the website from the internet.
I have the feeling that I conceptually don't understand something correctly. I would appreciate if somebody could help me with this problem.

See this article:
http://support.apple.com/kb/HT1866
Sometimes My Music does not show up in special folders in TweakUI.
If so, see this post:
http://discussions.apple.com/thread.jspa?messageID=1731188&#1731188##
If you would rather not mess with the registry you can often work round with a shift key start.
Hold down the shift key and start iTunes, keep holding down the shift key until you are asked to choose or create a library. If you already have one, navigate to your iTunes folder and choose iTunes Library.itl. Otherwise create a new library in My music.

How to enter a secure address in security so i can have access to web site

I used to be able to enter an address from a secure website and be able to access when I had internet explorer and with firefox I dont know where to enter address so I can access the secured we site.

Firefox doesn't have security zones like Internet Explorer. There's no Trusted Sites list to add sites to. Normally, web sites simply work, whether they're secure or not.
If secure websites don't load, see the following article.
* [[Websites don't load - troubleshoot and fix error messages]]
If the website does load but you're having some other problem with it, see the following article.
* [[Websites look wrong or appear differently than they should]]
If neither of those answer your question, please post a link to the site and or a description of what doesn't work, or whatever error message is displayed.

Can't access some web sites with version 4.0

I recently installed version 4.0 and am in test phase of the server.
With or without ACL's turned on, I can't access the following web site
https://www.sunnet.sunlife.com/member/signin/index.asp?
or
https://www.sunnet.sunlife.com/member/
In Internet Explorer, it sits on a blank page with the little world logo spinning around until it finally times out after a few minutes. I've tried accessing these sites with both IE6 and IE 5.5 and get the same problem.
As a footnote, the web access to these sites works fine with our current Web Proxy version 3.6.
Does anyone have any ideas why this isn't working through the new Proxy 4.0?
Thanks

I did some additional testing through Proxy 4. All web sites and web pages including secure sites that I tried accessing over the past couple of days all appear to work fine with the exception of the forementioned sites. Access to these specific web pages (which I cannot currently access) are part of our day-to-day business requirements, and therefore will prevent me from using Proxy version 4.0 as our production proxy unless I can figure out why these web pages won't load, and how to fix the problem.
As an experiment, I tried to access these web pages through Proxy 4 with Mozilla FireFox and Netscape 7. None of these web browsers (including Internet Explorer) will bring up these web pages when going through Proxy 4. But bypassing the proxy or going through our v3.6 proxy works fine for these web pages everytime, and with all browsers. This leads me to believe that this web page access problem is not a browser specific problem, but something in Proxy 4 isn't processing the request to display the page properly.
As a reference, the web site in question is http://www.sunlife.ca. On the left hand side of the page go to "Sign In" then "Plan Members". Thats where the request hangs through Proxy 4 no matter which browser I use, including Netscape... but works perfectly fine with Proxy v3.6.
Can someone who is running a version 4 Proxy also please try to access the SunLife Members login page and see if it works or fails for you?
Thanks

How can I access a web site that is blocked?

The website listed below is blocked. How can I access it?

https://webinar.cms.hhs.gov/e13581911/event/event_info.html <br />
Loads for me. What indication do you get that it is blocked?

Can't get any web sites to load up in ssearch box then "connection has timed out" pops up

everything I type in in search box will not load. Can't get any site to load. Circle keeps spinning up on the top left of screen but site never loads

OK. Possibly onto something here. On the left hand side of the Business Rule tab there are all the calc scripts. Then only Bus Rule that appears there is a new one I created that was an exact copy of the Business Rule in question, just with a '- New' appended to the end of the name. Funny thing is both Business rules that are attached to the form do appear on the right hand side. Thus how could that be? How does one get the Bus Rules to appear on the left hand side? Haven't been in EAS Business Rules mode for a long time.

Can not access local web sites

Hi,
on my Mac Mini running Lion I cannot access any local web site
Normally, entering
http://localhost/~shortname/
would ad least show the index.html page located in the sites (Websites on German systems) folder, which I still can display w/o the webserver running by clicking on it)
However, I get the error message:
"you don't have permission to access /~shortname/ on this server"
This happens in Mountain Lion too, where I started the web server using the Web Sharing preference pane from
http://clickontyler.com/blog/2012/02/web-sharing-mountain-lion/
Any idea? I need this badly, because I am doing some little web dev
Thank you

Solved it, turned on FTP on Mountain Lion,
sudo -s launchctl load -w /System/Library/LaunchDaemons/ftp.plist
JR

Can't access one web site

I can browse the web perfectly with OS X 10.5.7 and Safari 4.0.2 except for one site - Northumberland County Council. Using both Safari and Firefox I just get 'Loading...' for several minutes then the message:
"Safari can’t open the page “http://www.northumberland.gov.uk/” because the server where this page is located isn’t responding."
I can access this site fine from my work pc using IE or Firefox. I have asked for advice on my ISP's forums, but because the site seems to work fine for others am not getting anywhere. I would appreciate any advice on where I should start looking for the problem.
I have an Intel Mac mini connected to the internet with a Thomson TG585 router.

Thanks sitspotsit, it seems to work fine from every computer except this one
I did add the OpenDNS servers a couple of days ago hoping that would fix it, but no change I'm afraid.
I assume I'm correct in adding them to my Airport/Advanced/DNS settings as I connect wirelessly to my router and don't use the ethernet?

Can't access ANY HTTPS sites, and problem affects only one user acct !

My new iMac (arrived yesterday) is driving me nuts, getting me sick. Countless problems ... def. not the experience I was hoping for ... (I'm not a new mac user, own a macbook for 3 years now).
The last one is that my account, for some unknown reason and all of a sudden (was perfect before), stopped working with ANY HTTPS connection ... banks, whatever ... anything that involves a secure protocol is out. I can't even login to my iTunes store. The message is that it can't estabilish a secure connection to the server. (Oh, the iTunes reports unknown error, wich took me 2 hours to find out that it wasn't iTunes fault, but the whole system was not working with HTTPS).
I already tried reparing the disk permission, verifying the disk (no errors found), AND reparing the keychain using the keychain aid. Oh, I also reseted Safari ...
The weirdest part of it all is that another account I had set up on the iMac works just fine. JUST FINE. And my main account is hopeless.
Does ANYONE have any clue on this ?
(btw my new iMac just screwed my iPhone on the first sync ... it was supposed to go smooth since it was set up using a time machine backup from the macbook .. but no, it erased half of my apps in the iphone, including my task managing apps with LOTS of scheduled to dos ... this is ridiculous).
Message was edited by: FelipeRaul

i have the same problem on an imac for a non-admin user. admin user is working fine. have installed 10.5.5 yesterday without any change. all patches applied. have also removed user and system keychain, because this was mentioned in a forum, did not help either.
please help

When opening a second window, homepage doesn't open and can't access any other site, stays a blank white screen.

After updating to Firefox 6, every time I open a second window, all I get is a blank, white page. My homepage doesn't open, either, even when I hit the home button. I have to manually type in my homepage address, and then, it's the only address that will show in the address bar, even after I leave the page or open any other tabs. The same thing happens when I open new tabs in the second window. Also, the back and forward arrows, stop, and refresh buttons do not work in the second window. None of the short-cut keys on the keyboard will work with in the second window, either. Most of the time, any page that I go to, in the second window, continues to load, never fully loading.
I even went back to Firefox 5 to see if that would solve the problem, but it didn't. I still have the same issues.
Everything appears to be working fine in the first window.
How can I clear all this up?
EDIT: I waited a few days and reinstalled Firefox 6.0 and everything seems to be working okay.

There's a good chance this is related to a bug that kicks in when you do not have Flash running in any tab and you open a new window to a page that does use Flash. The details are in this recent thread: [https://support.mozilla.org/en-US/questions/955659 Opening New Windows and Shockwave Flash].
I don't know whether opening a Flash site in a private window makes this problem occur more frequently. Maybe it does because the new window is more isolated from the previous one???

Safari can't find any web sites on hotel wifi?

Hi,
I have connected to the wifi service at the hotel I'm staying at but the only site I can get is google. If I type an address into the browser it says my computer isn't connected to the Internet, even though internet connect says I'm connected.
It did this at the last hotel I stayed at. Both my iPod touch and my wife's Archos can connect fine.
Is it likely to be a setting that needs changing on my Macbook?
Any help appreciated,
Thanks
Jono

open a terminal, execute
$ nslookup yahoo.com
(dollar sign is a prompt, do not type that)
you should get output similar to below, otherwise dhcp has not assigned your network settings (or you are not setup for dhcp).
mac-on-smack:~ rickc$ nslookup yahoo.com
Server: 192.168.1.250
Address: 192.168.1.250#53
Non-authoritative answer:
Name: yahoo.com
Address: 66.94.234.13
Name: yahoo.com
Address: 216.109.112.135
Go into system preferences --> Network
Click on TCP/IP
Check if it is set for DHCP
You could also try to renew the DHCP lease to have an IP addr / Gateway / DNS reassigned.

Can connect to WLAN, but can't access any web site...

Similar Messages

Maybe you are looking for