Can connect w/ PPPoE... but not route

Ok.. I've been working on this off an on for over a month and I have reached my end, I think.
Problem: I have a Linksys WRT54GL v1.1. My ISP (through cable, not DSL) requires a PPPoE connection. I can get the Router to successfully connect to the ISP and ping from the router... but I cannot get any traffic through the router to the internet. I've tried multiple devices, both wired and wireless. Below I have attached some screen shots.. hopefully someone smarter than I can spot my error.
PC's MAC address is cloned...
PPPoE connection established from the router...
I can PING the internet from the router...
I can PING the router from my PC...
But I can't ping the internet from my PC (through the router)...
Here is my network settings on the PC when attached to the router...
When I connect my PC directly to the modem, pppoe setup looks like this...
My network settings when directly attached to the modem...
And I can reach the internet when directly connected...
Any ideas?

Try a traceroute:
traceroute 64.233.167.99
traceroute 10.40.0.1
traceroute 10.40.32.1
See how far you get.
Otherwise this problem is difficult to troubleshoot through a forum. Your setup so far looks fully correct. If you run a firewall on the computer it may cause the problem. But other then that troubleshooting now would require to do some packet sniffing to find out how far packets get and/or what happens to the responses. This may indicate where the real problem lies. But computer and router seem to be set up correctly.
Beyond that you could try a factory reset pressing the reset button for 30 seconds. If there is an issue with the router configuration making the router operate like in router mode although it displays gateway mode this may solve your problem. Of course you have to set up the router again.
There may be a firmware upgrade available from the linksys web site for your router which fixes this issue.
Or change the mode to router mode, save the settings. Then change it back to gateway mode. Save the settings again. Maybe this fixes an incorrect setting in the router. You have to use gateway mode. In router mode you'll need a full IP address subnet from your ISP. As long as you use private IP addresses in your LAN you must use gateway mode.

Similar Messages

Can connect to Internet, but not router.

I know, this is the opposite problem from what most people have. I am trying to connect through a WRT54G v.6 to the ethernet port in the wall (I don't know what the building is hooked up to, we just have ethernet ports next to our cable jacks).
If I run an ethernet cable from the wall to the 10/100 port of laptop, I connect to the Internet just fine.
If I run the ethernet cable to the WRT54G, and then connect to it using my wireless card and the default, unsecured "linksys" SSID, I connect to the Internet just fine, but I can't access the Linksys router at 192.168.1.1 (though I can successfully ping it), and if I try, though I do get the password window and put admin as the password, the Internet stops working completely.
If I run an ethernet cable from the wall to the WRT54G and from the WRT54G to my computer, as you're supposed to and as I did when trying to set it up this morning, neither the included software nor Netset will give me access to the router. Trying 192.168.1.1 in the browser brings up the password window, but no amount of resetting the router to its factory defaults will give access.
So there's my long story. I am, in fact, writing this via an unsecured, wireless connection to the default SSID. But if I dare try to access 192.168.1.1, I'll have to unplug the router and start again. What the heck is going on?

download the tftp utility from ftp.linksys.com/pub/network and upgrade the firmware

Can connect to appstore but not can't download songs or music albums

can connect to appstore but not can't download songs or music albums in mp3.

Sorry, but music tracks and other media contact are not available in Israel via an iTunes Store at this time. None of us here can say when Apple will be able to obtain the necessary licenses and feel it worthwhile to set up an iTunes Store for your country.
Regards.

I have a problem to connect with FaceTime. I am using OS X 10.9.1 on a Mac PowerBook which is 4 weeks old. I can connect on iPhone but not from my computer.

I have a problem to connect with FaceTime. I am using OS X 10.9.1 on a Mac PowerBook which is 4 weeks old. I can connect on iPhone but not from my computer. Does anyone have a similar problem???

The warranty entitles you to complimentary phone support for the first 90 days of ownership.

Can connect to skype but not internet, running snow leopard

Moved to new house; was able to connect to internet with firefox first day; after that can get on Skype but not internet. Is it my computer or the wireless router in the house? what should I do?

This is all I could find on the topic, but it doesn't resolve my issue:
http://docs.info.apple.com/article.html?artnum=106798
http://docs.info.apple.com/article.html?artnum=106797

I can connect to WiFi but not the internet

I am trying to connect a new IPad 2. I have a Belkin router that is B+G+N. I use WPA2 encryption and MAC filtering. The IPAD's MAC address was entered into the router and when I provide the encryption key as the password I am able to connect to WiFi but not anything Internet related except for email. When I type any URL in Safari it takes me to my router's management page. In fact I can log into my router and manage it from my IPad but I can't connect to anything else. I have 8 other computers/devices that connect to the router fine including two Apple Ipod touch's. This has me baffled.

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

I can connect to MAC but not my PC

I have a new Nano, that connects to Mac but not my PC. When I try to connect to PC it says "iTunes as detected a Macintosh formatted iPod. You must restore this iPod before you can use it on Windows."
How can I get my Nano to work on both?
Thanks!

Windows cannot read a Mac formatted disk.
You need to Restore on iTunes for Windows and it will then work on Mac & Windows.

Changed to secure - can connect with mac but not pc running vista

I changed my wrt54gs from unsecured to secure by changing the wireless > wireless security > to security mode: WPA personal, the wpa algorithms is set to TKIP, i set up a password in the shared key area and the group key is set to 3600. I saved the changes and now i can connect with the password with a macbook pro as well as with a ipod touch but i cant connect with a laptop running windows vista. I would get an error saying unable to connect, funny thing is though i am connect (and it is the correct router, not a neighbors) but it says connected with limited access. I tried to run diagnostics and repair but to no avail. Any thoughts on what to door is limited access ok?
thanks,
Dave

Try this :
Click Start >> Control Panel >> Network and Sharing Center >> Manage Wireless Networks, here remove all the networks present and close the Window...
Click on Connect to a Network and try to re-connect to your Network, it should ask for your Network Key/Password, enter the correct password/network key and click Connect...
It should connect...Once you are connected you should restart the computer, it should connect to Internet...

Can connect to wifi but not to Internet

I had the problem that iPad2 suddenly could connect to wifi, and to 3G for that matter, but got an error trying to acces the Internet (from Safari or mail).
Tried for hours all the advice foud here and other places, like resetting this and that.
I had a feeling that it was something blocking on the iPad, not a router problem - all other devices could connect to Internet.
The solution: I had disconnected Dropbox! - Connecting to Dropbox again solved all problems. Now it's even possible to disconnect to Dropbox without getting problems with Internet access.
The lesson learned from this: apps can hang up Internet-connection, though they are not even using it!

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Can connect to network but not internet. Please Help!!!!!!!!!

I have a Thinkpad T-60p and have encountered a serious problem; I am unable to connect to the internet. The Thinkpad will recognize and connect to wireless networks but when I go to actually open a webpage it does not open. I spent hours troubleshooting the problem to no avail. My other laptop connects to the internet fine, so I do not think it is an issue with my router or modem. I also went to my neighbors and I was unable to connect to the internet even though I could connect to his network; once again my second computer does not have a problem. I tried what I could in the Thinkvantage wireless software but I am not that familiar with it. When I use the test connection option it just reads, “unable to connect to internet” but I have a strong signal to my network. I then tried a wired connection directly to my cable modem and my neighbors; once again it showed that I have a connection, but still will not connect to the internet. I tried disabling my Firewall and Virus software and still could not connect. I have shutdown, unplugged and reset everything. I still receive the same results. I am not sure what has happened, I have not installed any new software or hardware recently. The computer has been working great up until this morning. I ran my virus software and a free online scan as well, nothing had been detected. I called tech support and they said it was a software issue to either pay $100 for help or post in the forum. The only other option I can think of is a complete systems restore, which I am trying to avoid. Anyone have any suggestions?
Please Help,
P.

ConnectDon wrote:
Perhaps the domain names are not resolving properly. Instead of http://lenovo.com, try http://64.26.254.19, which is the numerical address for lenovo.com. If you see the Lenovo home page, it will point us in the right direction.
Don
I will try that when I get home from work, thank you for the advice. However,I did notice that when it attempts to connect it shows the IP Address in the IE window bottom left corner. In the past it would always read connecting to "website name" but since the problem started it shows the IP address instead of the actual name.

Can connect to Wifi but not LAN internet with iphone 6

Hello from Australia.
Ever since I brought my iphone 6 home, I have been plagued with Wifi issues. All of my idevices have lost internet connection, even though they can be connected to WiFi via Airport Express (2nd gen).
My internet is a LAN ethernet cable, and usually after connnecting to WiFi (on any device), I get a Login Page from my ISP and I can connect to the internet as usual.
The new iphone 6 has never been able to bring up the Login Page, but is able to connect to my WiFi network. My old 4S is also unable to connect, as well as my husband's 4S.
Can anyone help?
Thank you.

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Can connect to bot but not people?

I am totally clueless as to why this would be, but although I can connect to the apple test bots (appleu3test01 to be exact), I cannot start an AV chat with any real people. I get what I understand to be the usual "SIPConnectIPPort failed" in the error report. This has been persisting for a few weeks now. I don't even know what information to give you about why this might be happening. All I can say is I'm connected via an AirPort express to a modem router that has a 1mbps connection to the web. Incidentally, the people I'm trying to talk to can start conversations just fine. And I've been able to use this perfectly well on another connection (at university). Any help would be appreciated.

The Test bots do not use NAT to appear on the Net.
In fact each one has it's own Public IP (they don't appear as if they are behind a routing device)
NAT is the biggest problem for iChat as it is not standard across all devices.
If there is No NAT at one end the chat is more likely to be successful.
Most domestic devices can not turn off NAT.
UPnP can help as it is less reliant on NAT to get through a routing device.
AS it allows the App to control the ports it is more like a constant outgoing call which tends to punch through NAT better.
As default on many devices the ports controlled by NAT (Those above 1024)and need to be opened for those applications that use ports this high (IM App On-line games)
UPnP allows the apps to open the ports they need when they need them.
Port Forwarding opens the ports you specify and points them to an IP (you need to specify this as well) so that you need to tell the device which ports iChat uses and which IP your computer is on your LAN
Port Forwarding can only open a port to one IP (computer), so say for iChat Text port 5190 can be opened to your computer and no other.
The set up is normally table based and several ports needs by one app can be set.
This means that on a LAN only one computer could then use iChat.
UPnP allows multiple computers to use the same ports.
Some devices have Port Triggering (Special Applications) that requires a different form of port ordering but can allow multiple computers but I don't think your device has this.
It is late here as well.
10:33 PM Sunday; June 15, 2008

Can connect to testers but not my mum!

Hi,
I have been trying for some time to get iChat 2.1 to audio or video chat with my mum in the UK (I'm in Japan). We both have iSight, iChat AV 2.1, OS X 10.3.9. I have a PowerBook G4, my mum has an iMac G5. I am using an NEC router (all in Japanese, which I don't understand properly), my mum is using a BT Voyager 205ADSL. I am using an Airport Extreme, but have tried with or without it - same result.
The message we are getting is something like 'mum/Tom did not respond'.
We can both connect to the AIM testers 'tryichatav' and 'ichatavtesting' with video and audio but not to each other. I have gone through the port opening procedure that Ralph advised us in another column 'iChat audio', but at that time we thought the problem was at my mum's side.
Now I know that we can both connect to the testers, I have absolutely no idea what to do or where the problem lies.
Any ideas would be great. Would us both buying new routers solve the problem for sure? If so we will do this as we are tired of this headache, what would you recommend?
Regards and thanks in advance.
Tom

Hi Ralph
I managed to connect with Tony last night through iChat AV using iSight, so can I assume that the problem isn't at my end now?
If so, it may be easiest (but not cheapest) for my mum to just buy a new router. If she bought the Netgear one mentioned above ought we not to have any more problems or is it just not as simple as that?
I enjoyed my first real use of iChat - it really does change a few things doesn't it...
It would be great for me and my parents as we hardly see each other, and iChat really does make meeting possible.
Many thanks to both Tony and Ralph for your help on this and other threads.
Tom
PS: I have two machines. I had been alternating between two computers in trying to connect previously - both running the same software - and always got the same errors. Last week I upgraded one to 10.4.2/iChat AV 3 and tried that with Tony last night. I am still waiting to try my new configuratin with my mum... Just in case that changes anything...

Can connect to airport but not load internet page

I can connect my PS3 and window based laptop to my airport network, as both show successful connection, but I can not load internet page on either the PS3 or the laptop. My airport network is not protected. My airport base station is about 7 years old.

Well the symptoms now point to a number of issues that need to be eliminated and they are you need to check that you are logged onto the ISP. For always ON systems this is usually a function of the Router in which case you need to log onto the Router and check the appropriate settings for this function also release the lease on the IP address and reboot the Router. The other issue is that the Router may not have access to the ISP which may cabling problem [disconnected or accidently damaged cable] within your environment of a service problem within the ISP domain. Check with a neighbour who is subscribed to the same Exchange as you are to see if they have problems otherwise call your Service Provider they may have to perform a reset on their end of your connectivity. Good luck
Message was edited by: adnixon

Can connect via Ethernet but not via AirPort

I'm having some problems using my AirPort in Germany. I can connect just fine using an Ethernet cable direct from the modem (NETGEAR DG632B) but when I have plug the Ethernet cable into the AirPort I can't connect. I beleive it has to do with PPoE settings, which I am not really familiar with.
There are three spots I can enter my account info. 1, on the modem itself via Safari; 2, on the AirPort via AirPort Admin Utility; 3, on the Mac via Network Preferences. I have input my PPoE username/password into the modem while directly connected. I would tend to think that this shoudl be it and that everywhere on the LAN side of the modem would be able to utilize that account. The NETGEAR settings page shows the ADSL port Network Type as PPPOE and the LAN port as DHCP, so I have attempted to set up my AirPort and Network prefs using DHCP. That leads to "You are not connected to the Internet. Safari can’t open the page “http://www.google.com/” because your computer isn’t connected to the Internet." Network Diagnostics shows green at AirPort, AirPort Settings, Network Settings and ISP. It initially shows yellow at Internet and Server which lead to "Failed" on both. Network Diagnostics then asks me to choose my network port configuration (Built-in Ethernet, Internal Modem, Airport,Other). I select AirPort and select my AirPort network. Then all the Status lights except for AirPort turn red and asks if I use a DSL or cable model. I select yes, it asks me to restart the device, I do, it asks if I can restart any other devices, I select no. At that point Network Diagnostics says it is unable to connect to the Internet.
I have down-graded to Airport Firmware v5.5.1 as some have advised. No change. I'm running MacOS 10.4.6
My AirPort is just fine as I can use it to set up a LAN with no problem. I even pulled out my old Graphite base station and tried it. Same thing.
I have tried putting my PPPoE account info into my AirPort, my Network prefs both individually and both at the same time. Nothing. Is there something that I'm missing?

You'll need to connect your modem to your AEBS WAN port, configure your AEBS with the Airport Admin Utility, setting up the PPOE to properly log into your modem connection.
You should set up your mac to us DHCP (not PPOE).
THis should allow you to use either the ethernet port or wireless from your AEBS.
I hope this helps!

Two Users can connect to apleu3test02 but not each other

Hello,
I have been trying to connect to with my wife whom is on a road runner cable modem behind a belkin wireless router. I am on a comcast cable modem behind a linksys wrt54gv4 router, however it is flashed with an open source firmware. Both of us can connect to the various test users out there but we have intermitent issues connecting with each other. I am guessing that this could be partially due to our maximum uploads being about 345kbps. I have not setup any port forwarding, triggering, or ther router adjustments yet. I figured if I can connect to the apple test users it should not be a problem. I am working on trying to test without my router but comcast will not let me mac grab a dhcp address. Any advice would be greatly appreciated.
Me = macbook pro 2ghz with 2gb ram 10.4.7
Wife = 1.67 g4 ibook with 512 mb ram 10.4.7

I'm having the exact same problem. My father and I were able to communicate for weeks with no issues and since updating to 10.4.7 we have a 90% failure rate with video chat. It worked once last night and once this morning otherwise its an error -8.
Now until recently we have never port forwarded anything except VNC and I can't see how we could use this method with iChat when we have numerous users here at home.
I think the most frustrating part is it works from time to time and I can find the reason why.

Can connect w/ PPPoE... but not route

Similar Messages

Maybe you are looking for