Can EBS in OVM server interface with second OVM Server or VMware ?

Pl. let me know which ones possible:
1. Win7 laptop --> Install VMware/VirtualBox ---> Install one OVM Server with EBS & GRCC and other OVM Server with GRCM & GRCI. Can they work in sych with each other (send/receive/communicate etc like various modules do within a ebs suite)?
2. Win7 laptop --> Install VMware/VirtualBox ---> Install one OVM Server with EBS & GRCC 64 bit and other OVM Server with GRCM & GRCI (all 32 bit). Can they work in sych with each other (send/receive/communicate etc like various modules do within a ebs suite .. 64 and 32 bit)?

And no I will always be using just one physical machine. And if i'm running GRCC and it needs any data from GRCM or ebs it should be available (like it would be if I had two physical machines/servers for EGRCC/EBS & EGRCM networked together).You should be able to connect between the VMs.
1) So pl. recheck the the sequence and let me know how to go about it without loosing win7.As long as you do not use Oracle VM you should be fine.
2) Can 2 Oracle VM Servers run within the same VMware or Virtual box?
(say one with EGRCC/EBS & other with EGRCM)You are not clear about this, if you use 2 different VMWare or VirtualBox machines then you should be fine.
3) In case (2) above is not possible can I have 2 VirtualBoxes on/in same physical machine running win7 ?
(Two VirtualBox/VMwares - VirtualBox/VMware No 1 running Oracle VM Server with EBS/EGRCC & VirtualBox No 2 running EGRCM).Yes.
Thanks,
Hussein

Similar Messages

Can I use my MBox interface with the latest version of Logic Pro X?

Can I use my Mbox interface with the latest version of Logic ProX?

If your Mbox has a Core Audio driver compatible with your version of OSX, then most likely, yes.
J.

How can I get Labview to interface with Altera PLD?

Hello, I am a student trying to design a Labview interface that will download test data to an Altera EPM7128slc84-7 chip. The chip should process the data and send the results back to Labview for analysis. Is this possible. I am just learning Labview and any help will be appreciated.

This chip is mounted on a what is called an Altera education board. There are a number of external access points where i can hardwire from this board to a DAQ board associated with Labview...the DAQ board is on a similar set up......I think I can use the digital i/o ports to send and receive data. I think I have made the problem harder than what it is.. Like I said, I am just learning Labview and its pretty much trial and error for now...Thanks for the advice though!

Can I use one GBIP-Interface with two programs at the same time?

Hi, I have one PCI-GBIP-controller with multiple instruments installed. Now I want to use these instruments with two differents programs at the same time.
E.g.: program 1 uses GPIB0::1 and GPIB0::3
and program 2 uses GPIB0::4 and GPIB0::7
Is this possible??
When I have tried to do this, I always got timeout errors..
Thanx in advance.
Philipp

Hi,
You shouldn't have any problems accessing different devices from different programs using the same interface. I even used the two VIs to communicate with the same device. Although not the best approach, VISA didn't return any errors.
DiegoF.

Can i use my digidesign 002 with logic pro 9

Hi does anyone know if i can use a 002 to interface with
with logic

You will have to check with AVID/Digidesign to see if they have Core Audio drivers available for Mountain Lion.
Logic is Core Audio compatible so an interface has to have Core Audio drivers that are compatible with the operating system they wish to use it on.

Interface with Exchange server

Hi i nbeed to write a program to interface with ms exchange dose anyone have any sample code i can look at? i need to extract info such as appointments.

I'll be interested too. I'm writing a java app that would need to read and create calendar appointments, contacts and tasks. The java app is a CRM program, and its database becomes master for the exchange server that would replicate certain information coming from the CRM database/system.
rgds,
David

Creation of Server Proxy for Message interface with External Defination

Dear All,
I am getting a problem while generating a server proxy for the inbound interface . The request message used in the inbound interface is a external definition which is uploaded using a XSD file. The XSD file was supplied by a third party which is having very high complex strucuture and used lot of abstract data types in the design. When i tried to generate the proxy in the R/3 system (Transaction SPROXY) for the inbound interface i am getting following error.
Interface uses external and internal message definitions
Message no. SPRX122 *
Diagnosis
In a message interface you can use messages from different sources:
Message types and fault message types edited in the Enterprise Services Repository
Messages imported into the Enterprise Services Repository (external definitions, RFC, IDoc)
In the current message interface, message types from different sources have been used. Since messages from these different sources must be handled differently during proxy generation, such a mixture of messages within a message interface is not possible.
System Response
The interface cannot be generated.
Procedure
Change the interface definition accordingly in the Enterprise Services Repository.
Please guide me, how to generate the proxy for the interface with external defination message. I could nt geneate manullay, because it is having very high complexity and its a big structure.
Is there is any way to generate the proxy for interface with external definition
Regards
Vijayanand

Hi,
i. Import your message schemas from external definitions, or RFCs or IDocs from SAP systems. These definitions already contain data types.
ii. Create a message interface and reference the messages of the external definition, or the RFC or IDoc message.
Check this, it may help you
http://help.sap.com/saphelp_nw04/helpdata/en/3f/01623c4f69b712e10000000a114084/content.htm
REgards
Seshagiri

Can a website built with adobe muse interface with a database such as an Excel spreadsheet?

Is it possible for a website built in Adobe Muse to interface with a database? I need to turn a rather robust excel spreadsheet into an easy-to-use website that links to a database that can be updated easily and regularly. Thanks.

Hi,
Muse is a designing software. You can design websites in Muse and host it on any server of your choice. There is no native feature in Muse to convert a spreadsheet into a website. If you are good with coding, you can develop it outside Muse and call it in Muse site using iframes, if at all it is helpful to you.
Regards,
Aish

Can I use OVM templates with VirtualBox

Oracle has lots of OVM templates available on edelivery for Oracle E-Business Suite. But it seems that to get those I need to install OVM and would not just work with VirtualBox.
Is there a possibility that I can use them directly with VirtaulBox instead of first installing OVM(as this would require formatting of my laptop).
Thanks & regards,
Gaurav

MikeLi wrote:
Hi Gaurav,
I also attempted to install R12 EBS and got stuck on the same issue that Oracle VM will wipe out the host. It is impossible for me as I use my laptop for other things.
I wonder if you have gone through with Virtualbox to install R12 EBS and found any issues with it?
Thanks, Mike.Mike,
You can use VMWare if you want to keep your client OS.
Note: Please create a new thread if you have any issues/questions instead of updating multiple threads -- Demo Vision Installation of Oracle EBS R12.1.3
Thanks,
Hussein

Can you help? Two dialer interfaces with IP SLA for default route failover - issues

I have an issue with a Cisco 2821, it has an ADSL2+ HWIC whose ATM interfaces is linked to dialer 1 and a Gi0/1 interface with a pppoe client which is linked to dialer 2. Both dialer interfaces are up with their respective IP addresses. If the ADSL on dialer 1 fails i want the IP SLA to kick and and replace the default route for dialer 1 with one for dialer 2.
This config works if you manually shut down the dialer 1 interface, it injects the default route for dialer 2 and then when you unshut the interface, the default route for dialer 1 comes back. The problem i have is if you take out the cable for the ATM interface and take it down, it does not take the route out the routing table and the default route for dialer2, which works if you just shut down dialer 1 does not appear.
whats the difference between shutting down dialer1 and it fails over the default route and taking the cable out then it does not?
Here is my config, i'm sure its something simple i'm doing wrong, can anyone help???
version 12.4
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
hostname Router
boot-start-marker
boot-end-marker
logging message-counter syslog
enable secret 5 $1$qOOJ$HV5AH6US/YZMuCGPYp3pP.
no aaa new-model
dot11 syslog
ip source-route
ip cef
ip dhcp excluded-address 192.168.0.1
ip dhcp pool pool1
network 192.168.0.0 255.255.255.0
default-router 192.168.0.1
dns-server 188.92.232.50 188.92.232.100
no ip domain lookup
no ipv6 cef
multilink bundle-name authenticated
voice-card 0
no dspfarm
archive
log config
hidekeys
track 1 ip sla 1 reachability
interface GigabitEthernet0/0
description Gi0/30 Local LAN
ip address 192.168.0.1 255.255.255.0
ip verify unicast reverse-path
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
ip nat inside
ip virtual-reassembly
no ip mroute-cache
duplex auto
speed auto
snmp trap ip verify drop-rate
no mop enabled
interface GigabitEthernet0/1
no ip address
duplex auto
speed auto
pppoe enable group global
pppoe-client dial-pool-number 2
interface ATM0/2/0
description ATM0_DSL
no ip address
no ip redirects
no ip unreachables
no ip proxy-arp
ip flow ingress
logging event atm pvc state
logging event subif-link-status
no atm ilmi-keepalive
dsl operating-mode auto
dsl enable-training-log
pvc 0/38
encapsulation aal5mux ppp dialer
dialer pool-member 1
interface Dialer1
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1492
ip nat outside
ip virtual-reassembly
encapsulation ppp
dialer pool 1
keepalive 1 3
no cdp enable
ppp lcp predictive
ppp authentication pap chap callin
ppp chap hostname ********@ccsleeds.net
ppp chap password 0 ********
ppp pap sent-username *******@ccsleeds.net password 0 ********
interface Dialer2
ip address negotiated
no ip redirects
no ip unreachables
no ip proxy-arp
ip mtu 1492
encapsulation ppp
dialer pool 2
keepalive 1 3
no cdp enable
ppp lcp predictive
ppp authentication pap chap callin
ppp chap hostname **********@adsllogin.co.uk
ppp chap password 0 *********
ppp pap sent-username *********@adsllogin.co.uk password 0 ***********
ip forward-protocol nd
ip route 0.0.0.0 0.0.0.0 Dialer1 track 1
ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 0.0.0.0 0.0.0.0 Dialer2 10
no ip http server
no ip http secure-server
ip nat inside source list 1 interface Dialer1 overload
ip sla 1
icmp-echo 8.8.8.8 source-interface di1
timeout 1000
threshold 100
frequency 3
ip sla schedule 1 life forever start-time now
access-list 1 permit 192.168.0.0 0.0.0.255
control-plane
gatekeeper
shutdown
line con 0
line aux 0
line vty 0 4
password test
login
scheduler allocate 20000 1000
end

Sure that EEM can shut/unshut interface...you have "event track" in EEM for monitoring track events...for example:
event manager applet test
event track 1 state down
action 1.0 command "enable"
action 1.1 command "conf t"
action 1.2 command "interfac dialer 1"
action 1.3 command "shut"
action 1.4 syslog "Dialer 1 down!!!"
action 1.5 end
This would be an example from head :)
You would need another EEM similar to this one for unshutting interface with "event track 1 state up" for bringing interface up again.
Again as I said you would need to test this before putting in production and you would maybe need to tweak this a little bit acording to your needs...
BR,
Dragan

Can we use applets as user interfaces with sockets, RMI and J2EE

Dear Sir or Madam,
Since I am a TA for software architecture class, some one ask me the following question: I think the answer is "No" based on the document on http://java.sun.com/sfaq/
How I answer the quesions? Looking forward your help!!!
1.You may have 2 applets and 2 html files. One applet with one html file may stay at a client PC and run on this PC, and the other applet with the other html file may stay at a server PC and run on this PC. In this case, all the applets are run locally.
2.Could applets works with sockets, RMI and J2EE?
3.Can we use applets as user interfaces with sockets, RMI and J2EE?
Thank you very much!
Best regards,
Jing

The scenario you paint doesn't quite make sense. The "server PC" wouldn't be running an applet, normally, since applets are by definition in a web browser page, and most likely involve user interaction, and "server processes" generally are done without user interaction.
The security rules around applets are that -- by default -- applets can connect with sockets ONLY to the server from whence the applet was loaded. RMI uses sockets (J2EE is too broad a spec) and hence RMI calls would also be limited to the server from whence the applet was loaded. Within that limitation, an applet could open all the sockets it wants, so long as they are all on the server from whence the applet was loaded.
If you want two applets on two different systems to communicate with each other, the simplest way is to have them rendevous through a server process on the server(s) from whence each applet was loaded. Maybe it's PC-a <-> server-a <-> server-b <-> PC-b ...? Or maybe PC-a and PC-b both are talking to the same server.
The limitation is rooted in the security subsystem. You can specify a policy file and override anything in the security subsystem. That does mean signing the applet and then cajoling the user into agreeing to grant greater levels of security than the default. In such a case you can open sockets more broadly and then PC-a could talk directly to PC-b without going through any servers.
- David

I have an iTunes account set up long ago on my home pc. My pc at home is antiquated and I can't interface with my account to edit acc. Info. Now I have other devices, iPhone 4 and iPad. I need to reset email apple Id and pw from iPad. How?

I have an iTunes account set up long ago on my home pc. My pc at home is antiquated and I can't interface with my account to edit acc. Info. Now I have other devices, iPhone 4 and iPad. I need to reset email apple Id and pw from iPad. How? Should I just create new account? Don't want to lose 1500 songs.

Hey Frankgates!
I have an article here that can tell you how to do this:
Apple ID: If you forget your password
http://support.apple.com/kb/HT5787
Thanks for coming to the Apple Support Communities!
Regards,
Braden

How can i link my E-mail with my iPad in a way that i can delete my messages from my email inbox server not from my iPad inbox only?

How can i link my E-mail with my iPad in a way that i can delete my messages from my email inbox server also not from my iPad inbox only?
Because when i delete emails from my iPad inbox, it will be deleted on my iPad only but when i check my email inbox server from the browser its not deleted!
So how can i set up this link so when i delete any email from my iPad it will be deleted from my email inbox server also?

Hi Pierrot10,
Insert your backup disc (or plug your external hd), then open Mail.
In the File menu, click *Import Mailboxes* and follow the steps for a *Mail for Mac OS X* transfer.
Navigate to your CD/DVD's or external HD's backup and hit "OK".
This should create a new "Imported" folder in Mail with all your old messages in it, that you can then rearrange as you wish, creating new mailboxes etc.
Axel

I have 2 apple ID one for Egypt and other for USA , now I try to update the software but I get a message said that this software download with other ID, then I logout and sign with second ID but i got the same message again ... Now I can not sign in more

I have 2 apple ID one for Egypt and other for USA , now I try to update the software but I get a message said that this software download with other ID, then I logout and sign with second ID but i got the same message again ... Now I can not sign in more
Any solution ?
I'm using iOS 6.1.2 IPad 3
Regards

I have also noticed the same "problem". I do not fully understand the impact of using the same ID on multiple computers and devices if I want to keep them all in sync.

Can not log into server computer with any accounts - "You are unable to login to the user account "abcdefg" at this time. Logging in to the account failed because an error occurred."

I have a Mac mini running the latest version of OS X and Server. Been running fine and flawlessly. However, I had a strange problem with the iCloud preferences panel crashing when I tried to access it, so I rebooted. Now I can not log into the system with any accounts. My master admin account (along with all the others) gives me the error:
You are unable to login to the user account "abcdefg" at this time. Logging in to the account failed because an error occurred."
I am able to see the server from other macs and I can log into it using the same account, but it only shows me a few of the shared folders I have access to but NOT to my main directories.
Rebooting into Command-R and doing a disk utility, I try and repair permission on that drive and get a bunch of errors like:
ACL found but not expected on Users
Repaired "Users"
ACL found but not expected on Users/.localized
Repaired "Users/.localized"
ACL found but not expected on Users/Shared
Repaired "Users/shared"
ACL found but not expected on Users/Shared/.localized
Repaired "Users/Shared/.localized"
Permissions repair complete.
But rebooting is no joy...same problem. Any idea what is going on or how to repair it? Should I do a time machine restore? Complete new OS X install? Any idea what is causing this or how to salvage it?

Got everything to re-install and it worked fine...for a few hours. Then I came in to find ALL of my network users deleted. Just GONE. Then found out the Open Directory was trashed and was unable to open, recover or restore from a backup. Looks like I may have a bad drive here.
I installed a new drive in the system, re-installed and so far (for a couple of hours anyway) the system seems to be working and stable.

Can EBS in OVM server interface with second OVM Server or VMware ?

Similar Messages

Maybe you are looking for