Can I connect my PA to my external audio card M-Audio Fast track Ultra?

Hello
I wonder if it's able to connect my PA to my external audio card, _M-Audio fast track ultra so that I can use every input from my PA and use them in logic._
Any Ideas?
Best regards Frankensten

So I should connect 2 guitar wires from the main outs, left and right to some of my audio card inputs and then Logic should recognize the sounds we are playing on the pa?
That should work.
Logic wont get any signal from the pa instrument if i don't press the front rear button on the audio card
That's normal. Those buttons control which jacks are active.
the sound is very low
Connect headphones to the headphones jack on the PA and make sure you're hearing a nice loud signal. You could also connect the headphones to the headphones jack on the Ultra, to check for a signal there.
There are level controls on the front of the Ultra. Try cranking them up. Also, make sure they are pushed in. When you pull them out, you engage a 20dB pad.
Also, look at the LEDs on the front of the Ultra. Are they glowing green? This means they are getting a signal.
In my PA there's two Monitors that I would like to use for logic, how would I do that?
You would connect outputs from your audio interface to inputs on the PA. You could use the channel inputs, or you could use the tape inputs.

Similar Messages

  • Can't adjust recording level with M-Audio Fast Track Pro

    I downloaded the appropriate driver for my M-Audio Fast Track Pro interface & everything looks fine... BUT I can't adjust the Recording level at all. I am not sure if this is an issue with the M-audio device, or garage band??? It is driving me crazy, since I just want to make some music and can't even hear what is being recorded. ???

    Thanks, .... Yes to all of the above. I am wracking my brain & will call M-Audio tomorrow. Everything looks perfect on the interface & on garage band - but, even though the Fast track Pro shows up in my sound preferences & I can select it as the input & output source, etc., when I go to its window, even hooked up, it says no "device is not connected." Then it details that there are "no input controls" under sound in system preferences. I have two working usb cords & it does the same on either. I think this is the problem & have no idea how to fix it. I just want to plug it all in and record & have lost So much time . Hmmmmm???

  • Can't get sound when using M-Audio Fast Track

    I'm using Logic Express 8 and just purchased the M-Audio Fast Track Pro interface so I can plug in my guitar and mic to Logic. I downloaded the driver, the device shows up in Logic, I can even record with it, but I can't hear anything on playback! Not only can't I hear the Fast Track, but I can't hear any of my other (software) tracks either. I can't input monitor at all. But, as soon as I unplug the device, suddenly all my tracks are audible again (including recordings that I make through the device). What's going on? I need to be able to hear what I'm doing!

    Go in to Audio midi setup and make sure the default input and output are the M-audio devise ... if you have not done so already .

  • Can I connect to iMac 27" as external display?

    I'm considering buying 2 iMac 27" to run Windows 7.
    Can I connect these two together so iMac 1 can use iMac 2 as external display and visa versa.
    In other words... is the mini display port both for input and output?
    If yes... does this work under Windows 7 as well?

    tjementum wrote:
    I just love Mac hardware, and an iMac (two in my case) on a desk is just such a nice clean setup, with only one cable. Just counted 16 cables for my current PC mini tower setup with 2 screens - don't ask
    Just so you know, I'm well aware of Apple's "cableless" marketing for this thing. But on my new iMac, I actually only have a single port, the FW800, that doesn't have a cable sticking out of it.
    But Mac OSX is just not a nice operating system IMO
    At least we can use you as an example of a 100% legitimate Mac owner of a Windows OEM install.
    Anyway... I just ordered 2 x 27" iMac's. If i somehow succeeds in getting them connected in Windows, I'll post here... if not feel free to ask me, in 6 months.
    Please do post back, because if someone tries it, then everyone will know if it works. I have seen reports of a PC driving the iMac display and I have done it with my MacBook Pro. I'm still not 100% sure that two iMacs will cooperate in this way. They both have the same cable connected to the same input/output port. Which one is the target? I have never heard of Windows or any PC hardware having the ability to convert a video port to input, so Windows would have to be the broadcaster. You may need MacOS X to detect the input and use it instead of trying to send out its own signal. Hopefully this won't short out the video circuitry on both.
    And in 6 months when you are reinstalling Windows to clean off all the malware, you can still use the Mac machine

  • Can I connect OS X to an external Exchange server?

    Firstly, I should mention that I just received my very first MacBook Pro today.   This is the first time I'm using OS X (or a Mac period), so I'm really fumbling my way around today.
    That said, I also own an iPhone 4 and an iPad 2.  On both of those devices, I can connect to an exchange server setup by my company for mobile devices.  That server looks something like amail.comanyname.com.  I love being able to get my Outlook mail on those devices.
    I've tried setting up that same mail server in the OS X mail client, but so far it's been unable to connect. 
    I'm wondering if there are any suggestions that might help me get connected?   Or is this just not possible to do on a desktop?  I have the same problem on my Windows desktop, in that I can't connect Outlook to the Exhange server there either.   I was hoping that since the iPad could do it, so could my Mac.
    Suggestions?
    Charlie

    Only if it's an AEBS. TM will not work with a disk connected to any other router. See the following:
    Requirements to use Time Machine
    Time Machine is only available with Leopard (10.5.x)
    1. External FireWire or USB 2.0 drive
    2. Time Capsule
    3. Drive shared by a Mac running 10.5 or later using File Sharing
    4. Drive shared by a Mac running 10.5 Server
    5. SAN volume managed by Apple's Xsan file system
    A TM drive must be partitioned with either APM (PPC) or GUID (Intel) and formatted Mac OS Extended (Journaled.)

  • Can't connect to NAS via FTP externally

    Hi all,
    Can anyone give me any straight forward adivse on getting FTP to externally?
    I have a WD My Book Live Duo (NAS) that allows FTP access, but it seems that no matter what I do I can not connect to it externally through FTP.
    I really need the FTP to work as the only other way to connect to it externally is via WebDav which is *really* unrealiable from from work connection.
    My setup is a MBLD behind an Airport Extreme Base Station (5th Gen) FTP connects perfectly when at home on internal network. AEBS has a static IP address and is connected via DHCP, the MBLD has a static address and is telling me that all is ok and that 'Port Forwarding' is established successfully. The MBLD has a reserved address using it's MAC address and IP address on the AEBS. Using Transmit 4.3.3 FTP client.
    I can't see anywhere in Airport Utility to perform port forwarding, do Apple call it something different?
    I'm probobly missing something really minor, but the constant altering of settings to get this thing to work is driving me mad.
    Any help would be greatly appreciated
    Thanks

    Maybe if you were to mention exactly which NAS device you are using and basically how you've configured it, and which version of the software that came with the device, someone here might have some experience with your exact hardware/software or something very similar and be able to help pinpoint a problem.
    There are many many implementations of SMB. Some (mostly free) don't work very well, even for Windows. Some need to be updated. Some seem to work very well.
    In addition, have you already tried using this device with Windows, Linux, another Mac? Did the device just quit working, or has it never worked? Without more information nobody has a chance because there isn't just one or two reasons that a NAS doesn't work.

  • Connecting a PC with an external wireless card

    I have an iMac and am connected wirelessly to the Internet through the Airport Extreme. My roommate has a new Dell Laptop with Windows XP and has been connected through ethernet to the base station. She just recently purchased an external wireless card, and we can't seem to get her connected wirelessly. When searching for available networks to join on her computer, it recognizes my network and says that it has an excellent signal, but when we type in the WEP, it doesn't do anything. It does not give us an error, and it does not connect. Any idea what we are doing wrong and what we can do to fix it?

    I still can't figure it out. I unchecked the option that says "enable encryption (using WEP)" and she was immediately connected. I don't think I have a huge problem leaving the network up without a password, I'm in a small residential area. Does that just mean that neighbors would be able to connect? How far does the signal generally travel? And is there any way to see the IP addresses of people connected to this specific network?

  • Can't connect to the store to buy the card from the "Cards" app

    Can't connect to the app store to buy the card after I created it

    Tryh this support article Sherri  >  Can't connect to the iTunes Store

  • Can WRT54G connect 2 XP laptops with different wireless cards, i.e. b and g,?

    My WRT54G router works fine with a lenovo windows laptop (Intel wireless 3945ABG card) and my dell linux box but it is not accepting my old T40 laptop which has a dual-band wireless a/b card.   The WRT54G box indicates this router accepts both b and g wireless cards. 
    Question is can this router  simultaneously  hookup these 2 laptops  or do I have to resetup the router in order for it to work on the T40?  
    as it is now, the wireless network shows on my T40 and it appears to 'take' the access key i input but then the T40 just 'hangs' trying to get into that network.   I have set the encryption key on the router to WPA. and i want to keep this.

    Make sure the computer that can't connect has DHCP enabled, Update the computer wireless card drivers, Check that the security you entered is correct.
    GoodLuck
    Matt

  • Can't multitrack with M-audio Fast Track and a Mac Mini

    I can't consistently record the two Fast Track channels, vocal and an acoustic/electric, simultaneously. I'm always able to record the channels independently just fine and they both come through if I create a stereo track. Every so often, after a random process of GB re-starts, track record button re-selections, and cable re-insertion, I'm able to get both to record at the same time but it's not a repeatable process. I've already done a permission repair. Any help or recommendations is greatly appreciated.

    Hi Jay,
    Welcome to Apple Discussions!
    One of 2 things come to mind. I couldn't find any decent information but
    1. The Fast Track USB might only be able to record either guitar/line in or XLR one at a time. Not simultainiously. I don't know, can't really say as I don't have this box.
    2. And this would be my guess. You may need to download the latest driver from M-Audio.
    It's been my experience (I had a MobilePre USB at one time) that an updated driver from M-Audio may not solve your problem. They aren't the best at supplying functioning drivers.

  • Can't connect to server internally when external internet goes out

    Whenever our internet service goes down, we can't even connect to our internal server through our own internal network. As soon as our external internet service comes back up, we can connect just fine. I can't figure out why the two would be related - here's the setup we have:
    Internet
    +
    Modem (bridge mode, passes internet signal straight through)
    +
    Airport Extreme (acting as DHCP Server)
    +
    Gigabit Switch (feeds ethernet drops to all offices)
    +
    OS X Server (acting DNS Server, with only itself identified as primary zone and verified)
    All client machines are set to use OS X Server as the DNS server using it's direct IP address. The OS X Server machine is set to use the Airport Extreme as DNS Server, Airport extreme has Open DNS set for DNS servers.
    So what about this setup causes our client machines to NOT find the server through our local network when we lose internet connection?
    Thanks for any help!

    What happens when you click this link, same thing? :
    https://www.google.com

  • Macbook Pro Retina (15") can't connect to wireless mouse and external USB keyboard

    Hi All,
    I got my new MacBook Pro Retina (15 inch) about 3 weeks ago. It works fine. I got a 30" Dell screen that I am using via thunderbolt/usb adapter. Also, I am using a thunderbolt ethernet adapter. Both adapters work fine without any problems.
    I have an apple usb keyboard connected to the USB hub of the screen, as well as my iphone cable. It is a regular, full size apple keyboard. In addition to this, I have a logitech nano connected directly to the right usb port of the macbook pro.
    This setup was working well until a few days ago. I lost connectivity with my mouse. Initially, I thought the batteries are empty. After replacing them, I still had no connection (again, the usb receiver is *directly* connected to the macbook).
    I changed a few cables here and there and noticed that I can get either the keyboard to work or the mouse but not both at the same time. A reboot did not help.
    Did anybody encounter such a strange problem already? If so, what could I possibly do?
    Thank You,
    --Martin

    Hello nikkig00,
    It is certainly difficult to use the computer if your wireless keyboard and mouse do not connect.  I found a few resources I recommend for this issue.
    I recommend reviewing this article first:
    Troubleshooting wireless mouse and keyboard issues
    http://support.apple.com/kb/ts3048
    If the issue persists, I recommend reviewing the section titled "Top troubleshooting tips" in the article below.  Step 9 specifically stands out to me for the issue you described:
    9. Restart your computer
    Sometimes a simple restart of your Mac is all it takes to get things running smoothly again. You may also want to try resetting your computer's PRAM and NVRAM.
    Bluetooth Quick Assist
    http://support.apple.com/kb/ht1153
    Thank you for using Apple Support Communities.
    Best,
    Sheila M.

  • How can i connect to a LAN and external display at the same time using the mini-displayport?

    Hi all,
    At work i'm connected to the Lan via an adapter and the mini displayport. I want to use my external display at the same time, which use the same mini displayport. Are there any splitters available to use both at the same time? Are there any other alternatives?
    Thanks,
    Dennis

    There are USB to ethernet dongles:
    http://store.apple.com/us/product/MC704ZM/A/apple-usb-ethernet-adapter?afid=p219 %7CGOUS&cid=AOS-US-KWG-PLA

  • How can I connect airport express to an external dac connected to stereo amp, How can I connect airport express to an external dac connected to stereo amp

    Hi just purchased airport express, how do I connect it an external dac which is connected to a stereo amplifier, what interconnect cables should I be using"" thanks

    Normally, you would need a Mini Toslink to Toslink cable. Example below:
    Amazon.com: 6ft Toslink to Mini Toslink Cable: Computers ...
    Most electronic superstores will have what you need as well.

  • Can I connect my iPad to an external CD burner?

    Am wondering if its possible to connect via hardwire or wireless to a CD/DVD burner from an IPad 4.

    Please read the post over on the right under the heading More Like this for the solution
    Allan

Maybe you are looking for

  • Issue of Free Sampling  to the customewith Excise duty[Paid by the Company]

    Dear All For free sample with no commercial value  the user want to raise invoice for plant on which excise duty is to be paid.In this senerio excise duty is to be born by company only  no recovery from the customer. I dont think it is possible in no

  • How to change the Group Display Name in the UME?

    Hello experts, from time to time due to reorganisation our departments group names change. So far this was a big deal because it is not possible to change the Display Name of a group created in the Portal´s UME? So far a new group with the department

  • Problems while migrating ODI code from 1 env to other

    Hi, I had some ODI code in Env1 i moved it to Env2 and did some new development(created new models, packages etc) over there and then tried to migrate it into Env3.What i found that the exports for new development done at Env2 got imported easily in

  • Duplicate record identifier and update

    My records look like  Name City Duplicateindicator  SAM   NYC   0 SAM   NYC1 0 SAM    ORD  0 TAM   NYC  0 TAM   NYC1  0  DAM   NYC  0   for some reason numeric character are inserted into city which duplicated my records ,  I need to  Check for the d

  • More than one iphone

    I have an itouch 2nd gen. I have purchased the new iphone 4. Do i need another itunes account on my computer? Also, how would I transfer my itouch apps to my new iphone?