Can I connect TC to DV4210-WA modem?

Can I connect my TC to a DV4210-WA Inventel modem? I get no access to the internet when I follow the basic instructions.

Simply use the TC in bridge.. plug into the TC from the computer or use wireless and airport utility.. go to the internet tab and make sure it is set to dhcp.. go to the network tab and set to off (bridge mode).
The later being the most important.. I think the internet will automatically go to dhcp in that case.
Make sure you create a wireless network.. not extend.. you can turn off the wireless in the modem.

Similar Messages

Airport Express: can't connect to internet via adsl modem

I have an old Airport Express which has worked fine in the past and a new ADSL internet account which works fine when I connect to it via PPoE Built-in-Ethernet. But despite following all the instructions in the Airport Setup Assistant I can't get Airport to work with the new modem (it works fine for AirTunes though). The thing is I don't really get how it could work with the new modem seeing as the Airport Setup Assistant doesn't ask me at any point what the username or password is for the new account.
I guess I'm missing something obvious here. Does anyone have any ideas what it is?

Thanks again, I tried that but it didn't work either. Going back to basics, it might help if I tried to set out what I'm trying to take in a bit more detail:
1. Having just moved house I have a new ADSL line and modem installed by the phone company and a new ISP that has provided me with a username and a password. Using those I have no trouble getting internet via an ethernet cable connecting my iBook and the Modem.
2. I plug the ethernet cable into my AX and then plug the AX into the wall.
3. Then I follow the AX set up assistant guide for setting up a new base station.
4. I click the box for DSL or Cable Modem. I don't click the box for Router
5. This is the step I'm most unsure about. Because it is the default option I click the box for DSL or Cable modem ... or over Ethernet with an IP address assigned automatically using DHCP." I do not tick "I do not use DHCP". But I don't really know what that means.
6. AX tells me that it is configured as follows: TCP/IP: using DHCP and IP Address: Provided automatically.
7. When I open Safari it tells me that I'm not connected to the internet. Clicking the network diagnistics box gives me green lights for everything up to and including ISP but not for the internet.
Someone here mentioned that I might have to reconfigure my modem as a router. Is there anything to that?
Thanks again for your help.

Can't connect to internet, Motorola cable modem seems to freeze

I have had this problem more and more fequently the past three or four weeks: I'm connected to the internet by ethernet through a motorola cable modem (SB5101). As long as the PC activity light on the modem is rapidly flashing amber things are fine. As soon as the activity light goes solid amber with no flashing I can no longer connect to the internet or send or receive mail. During one of these "freezes" when I check network status in the network pane of system preferences the light beside ethernet is yellow and the message says-"Built in ethernet is currently active. Built in ethernet has a self assigned IP address and may not be able to connect to the internet." When I check when my connection is working I get a green light and this message "Built in ethernet is currently active and has the IP address 70.44.etc. etc.(not sure if I should make the whole IP address public or not)You are connected to the internet through built in ethernet." I also notice when I check the Built in ethernet under network in sytem preferences that the IP address changes depending on whether the modem seems frozen or not. When disconnect the power to the modem and reconnect, I notice that within about two minutes the IP address changes and I can get back online again. Or at least I could. last time I did this the IP address did not change and I couldn't get back online. Now I'm using my iBook connected via ehternet, which is working fine for now (past 15 minutes). When I first plugged the iBook into the ethernet (I normally connect to the iBook through a snow airport, which I've disconnected to try to isolate this problem) I got this message(with an exclamation in a stop sign)-"IP configuration- 70.44.53.etc in use by 00:01:50:23:3e:c2 DHCP server24.229.54.226". I clicked through the box, and the iBook is still connected to the internet and working. I have contacted Motorola tech support, and it seems the modem is OK. I will contact my cable company next, but I don't have high hopes. Any help would be greatly appreciated.

sig-
Thanks for your reply to my post. I was able to get back on the internet with the G4 using your suggestion, but the modem continues to freeze, whether connected to the iBook or the G4, using ethernet or airport. I will contact my ISP.

Can't connect LINKSYS router to DSL modem

I'm trying to set up a WRT54GS2 Linksys router with a D-Link DSL-2320b modem. Have a Westell 6100 modem that is going bad, so I bought the D-Link to replace it. Originally had a D-Link router connected with the Westell, but the router overheats often and has to be reset.
I have been able to connect to the internet using the DSL-2320b modem only, but once I add the Linksys router I am not able to connect to the modem. The Linksys router came from a cable modem connection for which it worked fine. I'm sure it has something to do with the fact that they both use the same IP, 192.168.1.1. I have tried changing the IP of the modem, but still having issues.
Any help will greatly be appreciated. I'm still able to use my old setup to connect to the internet now, but the Westell shut down my phone line today and had to be turned off and back on. I'm hoping to be able to replace this as soon as possible. Thanks in advance...

Connect the Mode to the router on the Internet port and the computer to the router on the Ethernet port..If the IP address of the Modem is 192.168.1.x then,change the ip address of the linksys router to 192.168.2.1 and power cycle the entire network and check...

HT1178 Do I want to create a new wireless network or join my current network? I can't connect an ethernet cable to the Mac / printer and to the wireless modem at same time - in two different rooms.

I am trying to set up Time Capsule so that I can do my first backup (after 1 1/2 years!) with Time Machine. I have read other forums, but in each case they instructions eventually do not apply.
I have connected my TC to my existing wireless router. This sits in a bedroom and cannot be moved as a rental home.
I have plugged in the TC and updated the software.
Now - do I want to A Create a New Wireless Network (remember I can't connect the TC to Mac using an Ethernet cable). B Replace an existing base station or wireless router with TC (only intend to use for TM as don't know other benefits as of yet). or C want TC to join current network.
Thinking C. If I choose C, it then asks A TC to wireless join current network (NO as already connected using Ethernet). B want to connect TC to my network using Ethernet to extend my existing wireless network. C want to disable the wireless network on this TC and connect it to my computer or network using Ethernet - CANNOT do this as devices can not be in the same room.
Or do I want to create new wireless network - first set of questions - choice A? What is the benefit to creating a new one when I won't be in this rental house for longer than 18 more months??
Please help and quickly! Thanks!

Let me suggest some things.
But first ask exactly what wireless router you have now and what type of broadband service?
Are you happy with the wireless on the current router? If so, then you can plug the TC straight into whatever computer you have by ethernet, short 1M cord with no connection to the network. And use it without affecting your existing network at all. This is trivial setup.
Although you don't say exactly what Mac and printer you are using, is it a desktop? Laptop it is definitely easier not to plug it in, but a desktop you can plug in the TC and it will all sit happily together.
How is the printer connected and to what?
I am not sure why you need such quick help.. this is all minor setup stuff.. and 18months in todays world is like permanent man.
Your multiple A, B, C are more confusing than helpful.
The best choices without more info.. are to replace the existing wireless router with the TC. ie your option B.. but how to do this depends on the type of connection. Is it cable or adsl? Can you easily bridge the existing modem router.. if that is what it is?
Think carefully in the ideal world what would you like..
and what do you have..
We can probably suggest ways and means to fit what you like to what you have.. without introducing a stack of options that are doing your head in.

How can I connect my iPad2 WiFi (no 3G) to my wired DSL modem (not wireless capable)? is there an adapter I can connect to the modem?

Yesterday I ordered an iPad 2 WiFi version (no 3G) and I want to know if it's possible to connect it to my DSL modem that is not wifi/wireless. Is there some sort of wifi adapter I can buy to connect to the modem or do I need to buy a wireless router?
TIA

If you have a desktop that can do "Internet sharing" and wi-fi, you may be able to use that instead of buying a router. I haven't done tihs recently but played with it with my iMac before I bought a wireless router.
But a router is the better option. They're not expensive and recent ones have some decent security. I have a Netgear WGR614 (v10) with a firewall built in making me double firewalled on the desktop (where all the really critical stuff lives like banking info and all) and it has an "access control" option where you not only password your network but specify exactly which devices can connect at all. Something I like because the signal reaches the street outside the house. That's a bit more "reach" than I like. Though, funny thing, my brother (who's iPad is authorized to use my net) did a quick update by pulling into my driveway once while I wasn't even here.
Any wireless can have a surprising reach. I live in a fairly rural area and I pick up on other peoples' wireless all the time. Which, out here, I did not expect.

Powerbook & iBook can't connect simultaeneously with D-link 300-t modem

Please help
After much pulling of hair I finaly got my G4 Powerbook to connect to the internet via my airport express through a d-link 300-t modem. This I achieved by changing the default ip address of the modem from 192.168.1.1 to 192.168.1.234 and configuring the airport express manually to be 192.168.1.233.
My problem is that my son now has an iBook which he can connect to the internet through the same modem, but we can't connect at the same time. I keep getting the message " 81.178.76.171 in use by 00:11:24:24:25:7d,DHCP Server 192.168.1.234" ( modem ip). Both machines configure IPv4 using DHCP.
I don't want to configure his iBook manually if I don't have to as he doesn't live here and I don't want to muck up his settings for other places he may wish to use it.
Any thoughts would be greatly appreciated
David Moore

Is the Airport Express distributing IP addresses?
Probably no
You can set up a new location on his iBook which will not conflict or change his current settings.
iFelix

Can't connect to internet..self assigned ip address problem with DSL Modem

I've run into this before, without resolution, and now again on a friend's iMac. Time to ask around...
Basically, everything appears to be assigned and configured perfectly, but the network status always shows, "...you have a self assigned IP address and may not be able to connect to the internet". Sure can't connect to the net when it says that.
I've gone thru the procedure advise before that details the sequence of events needed to insure the modem resets and recognizes the Mac and it's incoming DSL (sbcglobal) signal. The order of network priority is set properly by dragging built in ethernet to the top of the list. Modem was powered down, plugged in, and then connected to the Mac, but no solution. Any ideas? thanks

This continues to be a mystery. I've had my powerbook on several networks, and connection has, most of the time, been an automatic process. Additionally, I've installed new systems for people with the same isp, and all has been well. So easy is the process, it's never been an issue. However, following explicit procedural instructions (including powering the Mac down), has proven unsuccessful on 2 different occasions.
There is little help with the isp support in India, which is where the call routes too.
The only thing I have not done is to swap out the cable at one of the locations, but the other location, which has the same issue, works fine on the iMac there. Only when I connect my Powerbook to the modem, does the "...self assigned ip address...not be able to connect to the internet" appear.
I just keep thinking there has got to be a small detail that is being overlooked.

Can't connect to the modem's server.

Hi guys, I have a major problem.
When ever I connect to the internet with my modem, it works. But, when I connect to internet with my router and modem, I can't connect. But I have solved my problem by resetting both, my wireless router and modem. Then after I reconfigure my wireless router all I need to do is to log into my modem's server. But I can't connect to the modem's server. I tired logging in with "admin" (being the password) but I still can't connect to it.
I am using: Verizon Broadband Network
                 Ultra RangePlus Wireless-N Broadband Router model: WRT160N
                 Westell modem model 6100
What is the problem? Has anyone experienced this problem before?
Message Edited by machg on 04-11-2009 07:10 PM
Solved!
Go to Solution.

You will not be able to log into the modem as long as the router is plugged in
You must configure the modem first to bridge mode,then plug in the router and log into it
   1.)unplug router and have only the modem in
       go to 192.168.1.1 enter
      that will take you into the verizon modem/ if you have reset the modem then your user is; admin
                                                                                                                     your password is ; password
     once you lopg into that it will ask you to change the username/password
      just type in ADMIN in all 3 blanks
now you are logged into the modem;;;;;;go to network at the top,then network connections on the left,broadband connection ,you will then put your protocol on bridge/routed bridge,
now go to wireless settings at the top and make sure wireless is turned on
you have the option to set up a security key on basic security settings
once your modem resets then plug in your router,you are now in bridge mode and the modems connection has moved to your router. you must restart modem and computer for everything to take effect....
also make sure and refresh your network list on your laptop
Hope this works

Can't Connect Though Router/Can through modem

Hi everybody, I was hoping y'all could help me out with my problem.
Yesterday I had a cable modem hooked up in my dorm room to my already installed TV cable. Everything was working great until I tried to install my WRT54G Router.
I can plug in my laptop directly into the cable modem and get internet fine.
I have my router set up and my computer can establish a wireless network connection to the router.
However, when I connect to the router, I don't get internet.
Here's what I have tried:
*Installing newest firmwire
*Installing Easy Link
*Running CMD prompt to see if the router is working-Does work
*Checking to see if it is a DNS issue(typing in googles IP address)-Didn't work
*Installing the software on 2 laptops and 1 PC to see if it was a computer issue.
*I even returned the router to get a new one without any luck
I have installed 2 of these routers before without issue. What the heck am I doing wrong? Please help me out, thanks

Always check the router's status page on http://192.168.1.1/ to see the status of the internet connection. It will give you an error message when you try to connect and it does not work. You should check that.
Also remember that wireless routers come in a very unsecure configuration out of the box. Anyone in your proximity can connect wireless to the router and make any changes to the configuration until you change the router's configuration password and secure the wireless network with WPA.
Do any configuration through a wired connection to the router only to avoid configuring your neighbor's linksys router which he runs open.
Some ISPs remember the MAC address of the device/computer connected to them to prevent users to connect with multiple computers at a time. A clear indictation of this would be if only a single computer can use the internet connection, i.e. neither the router or any other computer could.
If this is the case, it sometimes helps to unplug the modem from the power and wait a few seconds and then plug it back in, followed by the router. Then the ISP accepts the router's MAC address on the line.
If this does not work, you could also try the MAC address clone function in the router. This is done again on http://192.168.1.1/ Search for the function on the tabs and clone the mac address of the laptop for which the internet connection works when it is directly connected to the modem. (there is a button which copies the address) Remember to save the setting. After the change you may have to connect manually on the Status page of the router.
Another reason for this kind of problem could be that your modem is not a simple modem but also a router. If the modem and the WRT both use the network 192.168.1.* you have an address conflict and it won't work. It find out about this, you could connect the laptop to the modem and verify you have an internet connection. Then open a command prompt window ("Run..." and "cmd") and enter the command "ipconfig /all". Copy the output of this command into your next post. It will show what kind of connection and modem you have...

Can we connect a hsdpa usb modem to an iPhone?

Hello everybody,
my question is: Can we connect a hsdpa usb modem to an iPhone?
Thank you

I don't think that is possible....

HT3466 Can one connect the Time Caspule to the iPhone to act as a network internet modem?

Can one connect the Time Caspule to the iPhone to act as a network internet modem? No fixed line service is available and using a dongle on the computer denies use of the network

Can one connect the Time Caspule to the iPhone to act as a network internet modem?
Sorry, but no. The Time Capsule needs a wired Ethernet broadband connection to be able to provide an Internet connection for connected devices. Check with your cellular provider to see if they have an adapter that might do what you want. Something like this...for example:
http://www.cradlepoint.com/products/mobile-broadband-routers/ctr35-wireless-n-po rtable-router

WRT54GL can't connect to modem

Hello,
My WRT54GL has been working fine for 6 month until recently. It started to drop internet connection and can't connect to the modem once in a while (like every 1-2 week). When this happens, the router's status page shows that it can't renew the IP. Physically the PC light of the modem is not lit even though the modem is connected to the router's WAN port. If I connect my PC directly to the modem the PC light lit up immediately. I also tried to connect the router's WAN port to a switch to test connectivity and the switch port light didn't light up either. Is it possible that I have a faulty WAN port?
Last night when it happened again, I tried resetting my modem and router, cloning Mac address, changing MTU to 1400 etc but no luck. The PC light of the modem just refuse to light up which indicate there is no connection between router and modem. However the strange thing is that after I leave the router off for a night, connecting it back to the modem works again.
Does anyone else has similar problem?
Thanks Alan

Upgrade the firmware on the router to the latest version hope this will resolve your issue.!!

I have an existing new belkin modem router which works fine with quite a few wired and wireless products in my house. My question is if i buy a time capsule can i put it in another room and wirelessly connect it to the belkin modem router, I would then ju

I have an existing new belkin modem router which works fine with quiet a few wired and wireless products in my house. My question is if i buy a time capsule can i put it in another room and wirelessly connect it to the belkin modem router, I would then just like my macbook pro and (imac future purchase) to wirelessly back up to it???????????

Your will need to perform a Factory Default Reset on the TIme Capsule to clear out the current network settings and then reconfigure it to "join" your wireless network using the AirPort Utility setup application.
To perform the Factory Default Reset on the Time Capsule....
Pull the power cord from the back of the device
Wait a few moments
Hold in the reset button on the back of the Time Capsule and keep holding it an additional 8-10 seconds while you simultaneously plug the power cord back in to the Time Capsule
Release the reset button after the hold period and allow 25-30 seconds for the Time Capsule to restart to a slow, blinking amber light
On your Mac.....
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click Continue
Follow the guided setup and choose the "join" option when it appears duriing the setup
You will need to know the exact type of wireless security that the Belkin router is using to enter this information during the setup of the Belkin. Otherwise, the Time Capsule cannot join the network, and you will receive an error message after the configuration process.

Can I connect window device like modem, mobile in oracle forms,if possible then how?

Can I connect window device like modem, mobile in oracle forms,if possible then how?

Hi Tony,
So explain where you would see your notification?I just mention, Leave module, there are many other module. For example In Purchase Purchase Requigition , Production Module Production Complite , Delivery Module Delivery Ready.
For this it will better to show at respective Menu.
In the Window title?Another good Idea !
You could have a timer trigger that runs every 5 minutes and checks a notification table, if there is an unacknowledged notifcation, then you could change the Window title of the formas app to show a (1) at then end of it.Timer has a bad this.. For example, if i make a timer and run every 5 min. then if user works on a form, timer will hide the form and show the timer window.
Isn't it ?
Would that do, or do you need more?Yea.. More..It will be like facebook. If any notified work is done by any person, light will go off.
Thanks for your interest and suggestion...
Ask2Learn
Edited by: Asked to Learn on Jan 23, 2013 12:36 AM

Can I connect TC to DV4210-WA modem?

Similar Messages

Maybe you are looking for