Can i control net amount in a PO
hi,
Can i control net amount in a PO.
i dont want people to create a po for more than xxx dollars.
but this check is not valid on all po.
only for a few po's which are used for assets.
thanks
Ram
Hello,
You can make use of function exit EXIT_SAPMM06E_013 to sum up all XEKPO-NETWR. This can be compared with your max. limit for chosen document type I_EKKO-BSART and throw an error message.
Thanks,
Venu
Similar Messages
-
Can I control the amount of time for timed loop
I was curious if it is possible to control how long each frame of the time loop takes or does it have to be constant for each section?
You can change the period for the following iteration.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines
Attachments:
change period.PNG 9 KB -
How to control Netpay amount for minimum payment case i.e. can't be less than 500
Hi
My user is coming up with a new scenario in relate to netpay amount. The netpay amount can't be less than 500 in any case where total deduction(monthly) is more than the gross(monthly). Let's say an employee's gross salary is Rs. 10,000 and the total deduction amount is 10,500 so in that case the netpay will be 500. The balance deduction amount i.e. Rs. 1000 will be carry fwd to the next month's deduction.
Please guide me to work on the above scenario..
Thanks,
SantoshYou can maintain this fixed amount in the Minimum net pay - Fixed Amount Constant (MNPAM) of table view Payroll Constants (V_T511P).
You can find more detailed information here: http://help.sap.com/saphelp_470/helpdata/EN/0f/4c8c3c042e49d4bcd7ae4dad92225d/content.htm -
How can I control an iPad from a touch screen which is mirroring the iPad screen
How can I control an iPad from a touch screen which is mirroring the iPad screen.
This is a very important application for disability students who wish to use iPad apps but do not have sufficient fine motor skills to use the small screen of an iPad but could use a large format display touch screen.
There must be a way.?????????? Help!!
Peter Niass
[email protected]Have a look here
http://www.macstories.net/iphone/the-external-touchscreen-that-can-control-an-ip hone/ -
Calculation and posting of discount on Payment and on net amount
Hello,
My client would like to configure posting of discount on payment. The discount should be calculated on the net amount and should also adjust the VAT input tax amount. Example:
PO: 100 EUR, VAT 10 EUR, Gross amt = 110 EUR, Invoice recieved: 110 (-110 on vendor,100 is posted on GR/IR and 10 on input tax). When payment is done, discount amounts to 2.2 EUR ( 110 is posted on vendor account, -107.8 on bank account, -2 on discount account, -0.2 in input tax).
Have anyone of you ever did this on SAP. Can you pleas explain me the steps if yes? Thank you for your help.Hi,
I have already did a test with base discount on net amount and base vat on net amount check. When those are check, during good receipt the purchase account is debit with the net amount (gross -discount) and during invoice the difference is then transferred to the purchase account. The tax is calculated on the net amount. This is not what we are looking for. For us we want to know if it is possible that during good receipt and invoice received everything is calculated without taking into consideration the discount received. It is only when we are doing the payment of the invoice that discount is calculated and the VAT amount is adjusted for with the discount received. Thank you for your help. -
How to get - Net amount for accounting doc in the SD doc flow?
Hi,
In my report I have to show the net amounts from the Sales doc, invoice and accounting doc, etc.
I got the FI doc amount from BSEG, however there the gross amount is stored.
I noticed that in the SD document flow for the accounting document the net amount is shown.
I tried with the following calculation, however in some cases this doesn't work (eg there is separate tax item in the FI doc):
"<lwa_bseg>-wrbtr - <lwa_bseg>-wmwst"
Is there a function module/sap standard code to provide this data?
Thanks in advance,
Peterwhen u see the Item Header in SO or Billing , at the Head of Condition table u will get NET amount ?
are u not maintaining any seperate conditions for this NET amount ?
have a word with ur functional guys , so he can help u out.
Regards
Peram -
Report RFKOPR10 has to dispaly Net amounts, excluding VAT
Hi, Currently the Report RFKOPR10 is displaying the aging for 5 periods:
-Aging 0-30 days
-Aging 30-60 days
-Aging 60-90 days
-Aging 90-120 days
-Aging 120-150 days.
and Gross Amount (including VAT).
Now I have to diplay Net amounts, excluding VAT.
Could you please suggest me the logic where I have to change the program and How can I modify this program.
Thanks and Regards
NTR> Total Posts: 83
> Total Questions: 59 (44 unresolved)
You will get more and better answers if you follow up on your old posts. It would also help if you assign po1nts to helpful answer rather than just marking them as solved and adding a comment that doesn't add anything.
Rob -
Deduct Bank Commission at the time of F-53 on Net amount
Hi Experts,
My client who want the bank commission deduction at the time of vendor outgoing payment on the net values. the bank commission is fix of Rs. 0.07 Paise Per Rs. 1000/-
The scenario is as below:
Client who deduct the deduction at the time of Invoice for e.g. can bhade, Sanstha anamat , Prakriya Kharch ,Vahtuk Bhade, Share anamat etc. this deduction are directly update the Accounting GL .
after that the client pay the vendor dues amount. in this they deduct some deduction through Account (FI) (E.g. Sanstha Audit fee, Shikshan fund, machine anamat) & After deducting the Accounting deduction they calculate bank commission on the net amount (Invoice amount - FI deductions = Net amount)
Dear Expert, Please help me to work out this problem. in sap at the time of invoice we deduct the deduction as per client required & get the vendor due amount properly.
but at the time of vendor outgoing payment i had done the FI side deduction manually but i can't get the bank commission on the net dues amount. client required automatic bank commission deduction on the net amount. Please suggest me to workout the issue.
Warm regards,
Dhananjay Rahane.Hi Friend,
I know that the bank charges field is available on transaction F-53. but my business requirnment is differ. i have to calculate the bank commission on Net amount. ( Invoice amount - Accounting deduction = Pay net amount ). if we know the bank charges amount then it is possible through GL entry. but i have to calculate it automatically.
please give the valuable solution & help me work out.
Warm regards,
Dhananjay -
Can I control the spacing before and after a signature?
When using the Mail app, can I control the spacing before and after a signature? It seems like the app adds space, but it doesn't add the same amount every time.
Thanks.
GregThe only way I can think of to maintain equla spacing between the text ov vartying lengths and the vertical lines is to put each icon/text pair in it's own frame fitted to content, make each vertical line a separate object, then select them all and distribute the spacing.
-
F-32 Partial payment amount greater than net amount
Hi Experts,
We have recently a problem in clearing up payments in F-32. When we double-click the item under Partial Payment Tab, the warning message displays "Partial payment amount greater than net amount" then the value in the Payment Amount Column becomes negative. The users need to activate 2 separate entries for partial payment but instead of . How can we do this?
We have to post like this in partial payment under same customer:
20090820 1400005790 DZ 19 20.08.2009 20.08.2009 5,000.00- 1,295.12
20110225 1400010330 DZ 19 25.02.2011 25.02.2011 2,000.00- 1,295.12-
So the the Assigned Value should be zero to post.Thanks @Atif. Ok so now I understand that the "Total Difference Posting" amount inf-32 will create the new amount of the residual payment with Document Type AB.
Now with the Warning Message "Partial Payment Amount greater than the net amount", this is in a overpayment amount that is reflected in transaction F-32, here are the entries:
Assignment Doc Num Doc Type Post Key Net Amt Partially Paid Amt Payment Amt
2133004220 90005448 RV 01 3,707.02 3,305.71 401.31
2133015007 90020098 RV 01 7,836.68 6,737.25 1,099.43
2133016757 90022362 RV 01 10,521.31 8,603.87 1,917.44
2133137046 90187172 RV 01 11,367.68 0.00 11,367.68
2133137047 90187173 RV 01 1,354.09 0.00 1,354.09
2133137048 90187174 RV 01 1,739.82 0.00 1,739.82
2133137049 90187175 RV 01 994.57 0.00 994.57
20110419 90187176 RV 01 6.42 0.00 6.42
20110421 90187177 RV 01 44.94 0.00 44.94
20110425 90187178 RV 01 19.26 0.00 19.26
20081216 1400003657 DZ 19 3,421.86- 3,394.04- 27.82-
20081222 1400003706 DZ 19 1,000.00- 1,033.17- 33.17-
20090310 1400004396 DZ 19 420.51- 401.25- 19.26-
20090630 1400005319 DZ 19 786.13- 705.94- 80.19-
20090702 1400005349 DZ 19 596.04- 535.88- 60.16-
20090820 1400005790 DZ 19 5,000.00- 6,295.12- 1,295.12-
20090824 1400005827 DZ 19 308.16- 295.32- 12.84-
20091027 1400006377 DZ 19 400.72- 375.04- 25.68-
20091215 1400006796 DZ 19 349.89- 337.05- 12.84-
20100608 1400008253 DZ 19 200.09- 189.39- 10.70-
20101019 1400009279 DZ 19 165.85- 155.00- 10.85-
20101019 1400009280 DZ 19 254.65- 238.00- 16.65-
20101019 1400009281 DZ 19 160.64- 157.00- 3.64-
20101130 1400009595 DZ 19 10,000.00- 5,440.92- 4,559.08-
How is this possible that Document numbers 1400003706 and 1400005790 has overpaid amount. And both of them are downpayment documents? Is there any way I can clear them with the Invoices, I am also lost with this kind of scenario? -
Not to save customer order if net amount zero
Dear Gurus,
I want SAP not to save customer order if net amount = zero .
How can I do it by customizing?
Kind Regards,Hi,
Include VBAK-NETWR field and screen as KKON in the incompletion procedure in T.Code:OVA2
Tick the check box IC Dialog while assigning incompletion procedure to sales document type in T.Code: VUA2
System will nto allow the sales order to save if Net value field is Zero.
Hope this helps.
Regards,
Sharan -
Net amount field for invoices which got cleared
Hey All:
Can someone tell me what could be the field for net amount for invoice documents.
Thanks
SudhirBSEG-NEBTR
-
Can I Control the Pulse offset using the Counter Out?
Hello Everyone.
I am trying to generate the Pulse as below;
I have seen and understood an example to generate a pulse waveform "GenDigPulseTrain_Continuous".
However, I can not control the offset of the pulse train.
Although the function gives me "initial delay(The amount of time in seconds to wait before generating the first pulse)",
I can not shift "t_dead" cycle.
/*01.Frequency Control*/
// The units to use to define pulse frequency.
m_pTaskWrite->COChannels.CreatePulseChannelFrequency(vecstrings[0]/*LPCTSTR counter*/,
"PWM_C0_CH_HIGH"/*LPCTSTR nameToAssignChannel*/,
DAQmxCOPulseFrequencyUnitsHertz,
DAQmxCOPulseIdleStateHigh,
dDeadTime,
m_nFncFrequency/*frequency*/,
prDuty.second/*dutyCycle*/);
// The units to use to define pulse frequency.
m_pTaskWrite->COChannels.CreatePulseChannelFrequency(vecstrings[1]/*LPCTSTR counter*/,
"PWM_C0_CH_LOW"/*LPCTSTR nameToAssignChannel*/,
DAQmxCOPulseFrequencyUnitsHertz,
DAQmxCOPulseIdleStateLow,
dDeadTime/**2 + (prDuty.second *dCycleTime)*/,
m_nFncFrequency/*frequency*/,
prDuty.second/*dutyCycle*/);
Please let me know how I solve this problem.
Thank youDear Zl,
Counting pulses is much easier with the FP-QUAD-510 or FP-CTR-500, but can be done with the FP-AI-110. You can't directly count the pulses with a FP-AI-110, but you can do it in software. Bring in the data by doing a normal read. Then, using shift registers, if the previous voltage is less than .8V (low) and the current voltage is more than 2.5 (high), increase the pulse count. I have attached a program that shows what to do with the data once you bring it in. I took the data from an array outside the while loop, but your data will be brought in one point at a time inside the while loop. One thing to take note of, since Fieldpoint brings in data at 1 kS/s, this will only work with pulses slower than 500 Hz. The farther the duty cycle is away from 50% duty cycle, the slower the signal must be in order to catch the pulses correctly. Please let me know if you have any questions. Have a great day!
Sincerely,
Marni
PS- Please only post question once.
Attachments:
pulsecount.vi 22 KB -
Any ideas on how to control the amount of sustain pedal data that Logic Pro 9 records? Every time I press the sustain pedal down, it records 4 sustains. Same thing when I release the pedal. Thanks!
This gets confusing, you have two Macs with different issues and two pedals with different issues? First let's sort out what's what. So, do the issues come from the pedals or from the Mac software? To find out, simply switch the pedals and note their behaviour. No change: it's the software, change: it's the pedals (imho the most likely scenario).
Second, what kind of pedals are they? Can you name the type of pedal too? The Yamaha what and the Mgear which?
Third, with the 4 fold data problem, are the doubled events simultaneous, or a few ticks apart, or more?
Also, you have no MIDI keyboard? Are the pedals both "standalone"?
I think you have to sort this problem at its' source, which are the pedals. You could, if push really comes to shove, perhaps create some sort of ingeneous/elaborate transformer setup in the environment to filter the extra messages, although with the 4/4 sustain events that may not even be possible. With the "stepped" events you could set up a filter to just block all events with values 20-110 or so.
But much better would be to configure the pedal(s) correctly. -
Can you limit the amount of data accessed per user on an AirPort Extreme?
Can you limit the amount of data accessed per user on an AirPort Extreme?
Your question was whether the AirPort Extreme is able to establish data limits per user.
If you add another router that has this type of capability or install software on another router, then you will be able to establish data limits for each user. The AirPort Extreme will have no control over this.
Maybe you are looking for
-
BIP Outputting to PDF the second page starts 1 line higher than the first
Hello - Im using Embedded BI Publisher 10.1.3.4.2 to print a document to PDF. Once I print 45 lines on the first page, I page-break to continue on page number 2. For some reason the page 2 output starts 1 line above where it starts one page 1. It's a
-
Photo sort order is wrong on my ipad
The sort order is fine on my mac mini, but it's not on my ipad ipod touch or my iphone, the photos don't have the correct sequence, they're all messed up...
-
Create a screen for user input in BI
Hi Experts, I want to know can i creat a screen for user input in BI with module pool programing and i want to store the data in ztable in SAP-BI. Moderator message: please search for available documentation, these forums are no substitute for ABAP t
-
How do I add FCPX to the dock? and the Furore over FCPX
I already have FCP Studio on the Dock but when I try to drag FCPX to the Dock too it will not stay in place. I also tried to change the name of either FCP 3 or FCPX to differentiate one from the other, but that wasn't allowed. Any ideas as to how I c
-
How to create adhoc chain in process chain
how to create adhoc chain in process chain