Can I detect if a module is present in CRIO FPGA?

I have a cRIO-9073 controller chassis with 8 NI 9237 modules. I plan to use FPGA reads - not the scan engine. Can I detect whether a module is present or not within my FPGA VI? If not, is there a way to do this within the RT Host VI? (This is my first cRIO project so I'm still a bit green). I can foresee my client needing to replace a module sometime in the future and still needing to operate the system with the remaining modules - so the system must be robust and adaptible to fault conditions.
- Thanks in advance
- Tore
Solved!
Go to Solution.

I switched to the Find Hardware VI and it doesn't error, but what I need is network devices. I have expansion chassis on the network that I need to confirm are connected. The Find Hardware VI only lists off local devices. I asked about the error over at this topic here:
https://forums.ni.com/t5/LabVIEW/LV-RT-System-Conf​ig-Find-Systems-vi-Error-quot-2147220620-quot/m-p/​...
Thanks,
James
LabVIEW Professional 2014

Similar Messages

  • Satellite U200-181: How can I check if Trusted Platform Module is present

    How can I check Trusted Platform module is present or not?

    Hi
    The configuration of TPM (trusted platform module) is carried out in the BIOS setup program and this function is provided only with some models.
    I dont know if the U200-181 supports this or not but you can check it yourself.
    The security controller settings should be available in BIOS system Setup on the second site.
    If the unit supports the TPM you should see the switch to enable or disable this security option. Usually as per default the TPM is disabled.

  • How to detect as to which slot the SCXI module is present

    i want to detect to which slot the scxi module is connected . I have used get scxi info vi , but the
    disadvantage is that it does not give the exact slot position the module is present . Please let me know any vi which does this function
    Suresh Thangappan

    Hello Suresh,
    Thank you for contacting National Instruments.
    If you have LabVIEW 7.0 or higher, you can use the DAQmx Device Property Node with our NI-DAQmx driver. I have attached an example VI to demonstrate just how easy this can be accomplished.
    Regards,
    Bill B
    Applications Engineer
    National Instruments
    Attachments:
    Acq_Thermocouple_Sample.vi ‏54 KB
    DAQ_Device_Property_Node.JPG ‏77 KB

  • How can I use the print module to print different size images on one large "canvas"?

    How can I use the print module to print different size images on one large "canvas"? An example would be in Photoshop, go to file>new, and create the size paper I want, and move images of different sizes onto it.
    I was thinking the print module would do this automatically for me.

    You can't, at present. It's been a requested feature, so we'll see if it shows up in a future version, but it's not there at present.

  • Detecting C Series Module Fault through I/O Variable Node

    Hello LabVIEW Users.
    My name is Eisuke Ono, An Application Engineer at NI Japan.
    One of our customer is requesting a function.
    The function is to retrieve information of module fault from C Series I/O variable Node (Scan Interface).
    I know that we can get the information of module fault through FPGA I/O node, but not through Scan Inteface mode.
    The customer's application is embedded condition monitoring system. It runs 24/7.
    So it is very convenient if he get information of module fault C Series I/O variable Node Error Output.
    I agree his opinion.
    What do you think?
    Bestr regards.
    Eisuke Ono
     

    RT
    FPGA
    The goal is to detect Module Fault (Other than Communication Error) through IOV or FPGA node.
    If it is already implemented, I would delete this thread.
    Best!
     

  • Computer can't detect airport

    Hi, I'm trying to install an old airport express on someone else's computer but the computer can't detect the born

    The modem will connect to the first device that it sees, so this tells us that the modem has associated with, and will remember your computer.
    When you connect the AirPort to the modem, the modem still looks for your computer, but cannot find it, so it refuses to issue an IP address to the AirPort since it has not associated with the AirPort.
    So, you need to make the modem "forget" your computer. You do that by pushing the reset button on the modem....if present...and then powering off the modem completely for at least 30 minutes. Longer is better. Pull the power supply from the back of the modem or unplug from the wall.
    Power off the AirPort Express as well
    After the power down period, power up the modem and let it run for 10-15 minutes by itself.
    Then, power up the AirPort Express and let it run for 5-10 minutes.
    If the Apple Store configured the AirPort correctly, you will have an Internet connection now. If not, then we have to go back to square one and completely reset the AirPort and modem again.

  • MAX can't detect TPC-2106T

    not sure if it's the right place for posting this but i had to ask this
    I have TPC-2106T touch panel and want MAX to detec it but it won't for some reason
    i have the touch panel module installed and the touch panel is correctly connected to the network which my computer is connected as well
    MAX can detect my compactrio but it can't detect touch panel..
    Does anyone have any clue??
    thanks
    Solved!
    Go to Solution.

    Go through the following documents and post back if you have any other questions.
    LabVIEW Touch Panel Module Getting Started Guide for LabVIEW
    Getting Started with National Instruments Touch Panel Computers using LabVIEW
    Adnan Zafar
    Certified LabVIEW Architect
    Coleman Technologies

  • Win7 on dv6t can't detect Toshiba projector

    I have a Pavilion dv6t-2100 (WH770AV) running Win7 Pro 64-bit, trying to detect a Toshiba TDP-T9 projector.  When I first connected it, it worked perfectly as I previewed a presentation.  Then I moved the laptop and projector to another room, and now the laptop "can't detect projector" no matter what I do.
    When I connect the VGA cable between the laptop and the projector, I hear the tones of connection from the laptop, but the laptop screen goes black (no matter which setting laptop is on -- (computer only, duplicate, extend, projector only) -- and eventually I get the message "can't detect projector".  The projector continues to cycle looking for input, and cannot find anything.
    I am considering getting a new driver for the NVIDIA GeForce GT 320 on the dv6t, but won't until I hear if others have had this problem and have resolved it.
    Thanks!

    You should post your issue on the laptop forum.
    Does the NVIDIA Control Panel should see the second device? Look under setting up for dual monitors.  The keyboard also has a video display rotate key function (LCD, LCD off and both).
    You can also try a video driver update from the NVIDIA web site.
    HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
    HP Photosmart Premium C309G, HP Photosmart 6520
    HP Touchpad, HP Chromebook 11
    Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
    Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
    Windows 7/8 UEFI/Legacy mode, MBR/GPT

  • After my last update I can't start up an other keynote presentation from a link (only when the other presentation is already open) I hope there will be an  fix soon.

    After my last update I can't start up an other keynote presentation from a link (only when the other presentation is already open) I hope there will be an  fix soon.
    I thought it was because of Lion but with snow leopard i have the same problem (On another Mac).
    Other solutions????

    To check the local network for some of the common configuration problems, launch Terminal.app and issue the following diagnostic command:
    sudo changeip -checkhostname
    That'll report some local configuration information and then either no errors detected and no changes required, or it'll point to whatever configuration errors or issues it might detect.  That doesn't catch everything, but it catches the common errors.
    FWIW, 192.168.0.0/24 and 192.168.1.0/24 are poor choices for the local network, as VPNs are based on IP routing and IP routing gets tangled when the same subnet is used on both ends of the VPN. 192.168.0.0/24 and 192.168.1.0/24 are near ubiquitous in home networks and coffee shops.

  • Slot Detection of PXI Modules, More details

    I read the knowledge base titled: Slot Detection of PXI Modules but have a few questions about it. How often to I have to do this? When I insert or remove a board from the PXI chassis? When I insert or remove an additional chassis in daisy chain? With Multiple chassis in Daisy chain. How do I know which device number is which card? ie if I have 2 of the same model of cards both in slot 5 but in different chassis. If I remove a card, am I guarranted that other cards device numbers will not change?

    John,
    The Knowledge Base (KB) "Slot Detection of PXI Modules" says that the PXI Initialization File (PXISYS.INI) file must be saved in the systems directory in order for the system to be able to identify the slot where a board is located. This is because every slot in a PCI Bus (a PXI system uses a PCI bus) has a PCI Device Number and PCI Bus Number associated with it. The PXISYS.INI file describes the architecture of the chassis and the controller, and has the appropiate PCI Device Number and PCI Bus Number for every slot. There is a unique PXISYS.INI file for every combination of PXI chassis and PXI controller.
    How often to I have to do this? When I insert or remove a board from the PXI chassis?
    Currently you do not need to edit the PXISYS.INI file. You can download the PXISYS.INI file from our website and use it as it is (see link in the KB you were reading). So you only need to save once the appropiate PXISYS.INI file to the Windows Systems directory, regardless of whether you change the PXI board in your system.
    When I insert or remove an additional chassis in daisy chain? With Multiple chassis in Daisy chain?
    If you are daysi-chaining chassis, keep in mind that the current PXI Standard DOES NOT support daysi-chaining. However, in previous PXI configurations, I have successfully edited a PXISYS.INI file so I can do Slot Identification in daysi-chained chassis (not in star configuration, though). The steps I followed are in the text file attach to this e-mail.
    How do I know which device number is which card? ie if I have 2 of the same model of cards both in slot 5 but in different chassis. If I remove a card, am I guarranted that other cards device numbers will not change?
    Finally, if you are using NI DAQ boards, NI-DAQ driver will assign a Device Number to the boards that correspond to the Slot Number, and the Slot Number is described in the PXISYS.INI file that you edited following the instructions in the text file attached below.
    If your boards do not use the NI-DAQ driver, but support NI-VISA, you can use the PXI VISA Instrument Descriptor to find out the Slot they are installed in. See the KB "Programmatic Slot ID" linked below for more information. It has an Example Program linked to it too:
    KnowledgeBase 2MDFG2WD - Programmatic PXI Slot Detection
    Let me know if I can be of further assistance,
    Claudia Lorente
    Applications Engineer
    National Instruments
    http://www.ni.com/
    Attachments:
    PXISYS_for_Daysi_Chain.txt ‏4 KB

  • How Can I Detect Whether the User's Firefox Supports MHTML?

    Is there a browser capability property that I could look at to detect whether the user's version of Firefox (including, for instance, an "unMHT" add-on) supports MHTML? Currently we provide reports to our users in this format and want to provide a link to add-on's in case the user cannot actually view the format; but show the report if the add-on or capability is present.

    Sorry, you can't detect if a user has unMHT installed.
    Have you tested your MHTML files with Firefox and unMHT? <br />
    MHTML was never adopted as an official standard by W3C - http://en.wikipedia.org/wiki/MHTML - and from my limited usage of unMHT, it isn't exactly the same as what MS uses with IE. I have had problems displaying a file saved in one browser in another brand browser, and don't remember the specifics beyond IE8 won't correctly display unMHT files even when the file extension is changed from MHT to MHTML. Plus there's a 2nd add-on / extension - Mozilla Archive Format - that some users may have installed for MHTML files.

  • DVD-Audio and "can not detect sound blaster card" with Audigy2 Va

    I recently purchased an "Audigy2 Value" card from an eBay user, because I recently purchased some DVD-Audio discs. I downloaded the Audigy2 drivers from the website, and the Creative MediaSource player. 5. Surround sound worked fine for me, though sometimes the driver would reset to the default 2/2. sound and I would have to re-select 5. sound, which was annoying.
    Then I was completely unable to get the MediaSource player to recognise my DVD-Audio discs, and the EAX functionality of the player would never work. The EAX logo never appeared in the player. When I tried installing the MediaSource player from an install disc, I got the message "can not detect sound blaster card". Then I discovered the world of EEPROM problems.
    I followed advice from some other threads, including using ScanPCI to get information on the card, which yielded the following result.
    When installed on my machine (Asus A7A266 motherboard) the ScanPCI reads:
    Vendor 02h Creative Labs
    Device 0008h Unknown
    Command 0005h (I/O Access, BusMaster)
    Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
    Revision 00h, Header Type 00h, Bus Latency 20h
    Self test 00h (Self test not supported)
    PCI Class Multimedia, type Audio
    Subsystem ID 0002h Unknown
    Subsystem Vendor 02h Creative Labs
    Address 0 is an I/O Port : 0000A800h
    System IRQ 5, INT# A
    New Capabilities List Information :
    Power Management Capabilities
    Supports power state D2
    Supports power state D
    Current Power State : D0 (Device fully-operational, no power saving)
    On another machine (specs unknown, it's a "house pc") I got this (with 3 entries!):
    Vendor 02h Creative Labs
    Device 0002h EMU0K Audio Chipset (SB Li've!)
    Command 0004h (BusMaster)
    Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
    Revision 04h, Header Type 80h, Bus Latency 20h
    Self test 00h (Self test not supported)
    PCI Class Multimedia, type Audio
    Subsystem ID 002002h CT4850 SBLi've! Value
    Subsystem Vendor 02h Creative Labs
    Address 0 is an I/O Port : 00009000h
    New Capabilities List Information :
    Power Management Capabilities
    Current Power State : D0 (Device fully-operational, no power saving)
    Vendor 02h Creative Labs
    Device 7002h PCI Gameport Joystick
    Command 0004h (BusMaster)
    Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
    Revision 0h, Header Type 80h, Bus Latency 20h
    Self test 00h (Self test not supported)
    PCI Class Input, type Other
    Subsystem ID 002002h PCI Gameport Joystick
    Subsystem Vendor 02h Creative Labs
    Address 0 is an I/O Port : 00008800h
    New Capabilities List Information :
    Power Management Capabilities
    Current Power State : D0 (Device fully-operational, no power saving)
    Vendor 02h Creative Labs
    Device 0008h Unknown
    Command 0004h (BusMaster)
    Status 0290h (Has Capabilities List, Supports Back-To-Back Trans., Medium Timing)
    Revision 00h, Header Type 00h, Bus Latency 20h
    Self test 00h (Self test not supported)
    PCI Class Multimedia, type Audio
    Subsystem ID 0002h PCI Gameport Joystick (Guess Only!)
    Subsystem Vendor 02h Creative Labs
    Address 0 is an I/O Port : 00008400h
    New Capabilities List Information :
    Power Management Capabilities
    Supports power state D2
    Supports power state D
    Current Power State : D0 (Device fully-operational, no power saving)
    (Just a note: above you can clearly see that it does not say I have an Audigy, it thinks it is a SBLi've. Is this normal? The card IS an Audigy 2, it says so on the card.)
    So, I put the card back on my own PC, thinking this has fixed my EEPROM, but I get the same as before. Subsystem ID 0002h. And of course the install software will not detect the card.
    I realise that I could go back to using the web drivers, but this still leaves me with MediaSource not recognising the card and not enabling DVD-Audio or EAX, which is why I bought the card in the first place!
    I have heard that the VIA chipset is possibly to blame for the EEPROM problems on the Audigy cards, and certainly it seems like it is not permanent, since it gave different information on the other PC. So now I am seriously considering getting a new motherboard.
    Do other motherboards cause this same problem? I don't want to buy another board and get the same trouble. All I want is to be able to install my MediaSource and have it recognise my card so I can listen to my DVD-Audio discs.
    Cheers,
    Russ.

    Figured out my problem. Installing the drivers from the web to begin with was a bad idea. They just did not work properly with the card.
    The "card not found" problem has gone as well, after installing it in another PC. I am also using the proper install disc now, as the other one I was using turned out to not be for the Audigy 2 value after all, but was an Audigy 2 install disc. That easily explains the "Card not found" error. The differing results from the ScanPCI program are still bizarre, though.
    Thanks to all of the people on the forum who posted information in other threads to help me deal with this issue. For now I am sticking with the original drivers from the disc and I am not upgrading.

  • Can we call a function module in ADHOC query

    Hi
    Can we call a function module in ADHOC query if yes how.
    Also we ned to know how to call a function module in SAP query.
    An early responce is appreciated.
    Thanks and best regards
    Rajeev

    Okay as far as I understand your aim is:
    To fill a field in the output list with a value that is based on the current line information and calculated by a function module
    So go to SQ02 and create an additional field in the InfoSet.
    You can refer in the coding to the technical names you can see in the left tree window like P0000-PERNR.
    More information is avaiable in the Help part look for additional field in SQ02.
    Regards,
    Michael

  • APPLE/DEVS Read this! Windows 7 CAN'T detect the iPhone 5s but iTunes CAN detect it! WEIRD, huh?!..

    just a summary...
    i have a iphone 3G which i have been using for a long time and now i got an iphone 5s.. troubleshooting this kind of stuff is not new to me from computers to smartphones.. the internet has a vast majority of information and all you need to do is type in the right "KEYWORD".. i'm that kind of guy that looks for the answer before i try to look on it on my own.. i'm a DIY kind of guy as long as there is an instruction on how to do it..
    now, back to the topic..
    so i was trying to copy some of my pictures on my iphone 5s to my PC for backup purposes and to see the quality of the images but the portable device doesn't show up unlike my iphone 3G which is f***ing WEIRD.. been tinkering with this over the past 5 days since i have nothing to do and testing the new features of this phone but to no avail.. searched all over the internet but still none..
    so last night, i was really determined since i can't sleep and also connected my iphone 3G to my PC while the iphone 5s is connected.. so here is what shows up on my devices and printers and device manager..
    i can totally see the pics on my iphone 3G but not on my iphone 5s.. totally amazing.. good job apple!
    the picture under devices shows my iphone 3G and the other 2 on unspecified is my iphone 5s.. the iPhone under there is being used as my source of internet since this is tethered so i can have access and post this in here so that APPLE will know how f***ed up their SOFTWARE is is..
    so i downloaded itunes a couple of times, and i can't remember how many already, i think 5 times or more and then uninstalled all apple softwares (itunes, apple application support, apple mobile device support and etc as long as there is apple in it) and then reinstalled itunes but still none..
    so i went on device manager removed my iphone 3G and the only one that would show there is the Apple Mobile Device USB driver under USB controllers..
    and then i uninstalled the driver, looked for the driver myself by just it doesn't show up in here where you are directed to look for the driver and oh im using 64 bit just so everyone knows and i already found out that my system is using the usbaapl64.sys file in windows>system32>drivers..
    so last night i installed, reinstalled itunes and then suddenly my drive D: was gone and i received an error or a "!" on my drive and my drive is not being detected.
    Error: windows cannot start this hardware device because its configuration information (in the registry) is incomplete or damage. (code 19).
    i unstalled the driver in device manager and then scan hardware changes, updated the driver automatically and manually and it is saying that i have the latest hardware but i can't use my DVD drive with the error on it..
    so today i searched for that e-fing error and found this http://pcsupport.about.com/od/findbyerrormessage/a/code-19-error.htm
    "4. Uninstall Apple iTunes. While that may sound a little drastic, iTunes is the cause of enough Code 19 errors to make it into this troubleshooting.
    If removing iTunes works, you might try installing it again from scratch, which doesn't always reintroduce the problem. See How to Properly Reinstall a Software Program for general advice."
    so i then uninstalled my itunes, uninstalled my driver and then updated it and "walla!". i can see my DVD drive again. i am using iTunes64Setup v12.0.1.26 just so everyone knows and this setup can detect both my iphones and my iphone 5s is using the latest version which is iOS 8.1.2..
    after reinstallation of itunes my DVD drive can be seen and just  noticed how APPLE SOFTWARES are so ****** up.. CAUSING A LOT OF TROUBLE AND DAMAGES..
    so going back to the topic..
    i was able to find a way (AFTER HOW MANY HOURS of TROUBLESHOOTING) on how my iphone 5s was able to detect the portable device or should i say the images on my iphone 5s where the autoplay pops up and everything..
    so i went on device manager, uninstalled apple mobile device USB driver, disconnected my iphone 5s, UNLOCKED my iphone 5s, connected it to my PC, clicked on TRUST this PC, on my PC the sound for a USB being connected sounded, and at the bottom right, automatically installed the drivers and then the autoplay popped up with the matching PORTABLE DEVICES on COMPUTER where i can browse the internal storage and the pictures..
    so now i opened iTunes and BOOOM!
    iTunes doesn't detect my iphone 5s but i can browse on the images on my phone..
    so again i went to device manager, uninstalled the driver for apple iphone under portable devices, scanned for hardware changes, updated the driver manually by selecting drive C: so it would automatically find the correct drive..
    so now, my iphone can be detected by itunes but not on my COMPUTER.. see how ****** UP this is?!.. JEEEEEEEEEZ!!
    Now i finally found the SOLUTION on how to do this and vice versa.. UNTIL APPLE decides to FIX their SOFTWARE/DRIVER issues..
    if you want to scan or browse the images on your iphone 5s on your computer all you need to do is do this:
    [for those who don't know how to reach this part, here is a GUIDE on how to open this is: click on the device > click on update driver software > browse my computer for driver software > let me pick from a list of device drivers on my computer]
    and then you will see the screen below
    click on MTP USB Device and then click on Next, after it finishes installing the drivers, your PC will automatically detect a new portable device but in order for you to access the images you need to go back on your phone, unlock it if it lock automatically and then click on "TRUST" and then you can now see the images..
    BUT the problem here is that your iPhone can't be detected on iTunes...
    now, if you want to go back to where your phone can be detected on itunes, just follow these steps:
    click on apple mobile device USB driver, click on Next and then wait for your computer to finish the installation and then you will hear the beeping sound. check your phone, unlock it, then click on "TRUST", and then go to iTunes and you will now see your iPhone there but not on your PC where you can browse for the images..
    SEE HOW THIS DRIVERS are so ****** up.. i wish i hadn't started using this ****** UP OS with all the BUGS and GLITCHES.. JEEEZ! and to think, these DEVICES are not CHEAP compared to Android devices on the market.. it's just because of how these people go with the trend that they purchase these kind of stuff and the only thing they use it for is calling or texting.. i, for once use this not for calling or texting but also for the apps that it has like the games, ebooks and etc when im bored..
    i HOPE the Apple DEVS read this and find the solution on the drivers which is so ****** UP and so LAME!!
    PS: i hope a lot of people who are having the same issue as what i had find this and help them with their concern even though this is not a permanent solution.. it is just a work around for folks that are looking for answers and solution.
    Have a Great Day Folks and it is the start of a New Year and want to contribute something even though i don't usually posts my work around.

    Hi LSGZ,
    If you are having issues updating or restoring your iPhone, you may find the following article helpful:
    iOS: Unable to update or restore
    http://support.apple.com/kb/HT1808
    Regards,
    - Brenden

  • Randomly when I plug my Iphone 4s into Itunes it will tell me that it can't detect my phone and that I need to restore it. It doesn't happen every time, but maybe every two weeks.

    Randomly when I plug my Iphone 4s into Itunes it will tell me that it can't detect my phone and that I need to restore it. It doesn't happen every time, but maybe every two weeks.I restore it and then it works for a while, but then a couple weeks later I'll plug it in and I get the same message again. It's very frustrating because even though I have all the settings to save to cloud, my apps and data don't all come back.

    Thank you both. I suppose I should have prefaced my question with the concern that I've read a number of other posts from people who have had a similar issue and when they tried to follow the directions, they ran into a multitude of other problems. As you might imagine, I'm hoping to avoid the creation of new problems as I try to solve this one. Thanks again.

Maybe you are looking for