Can i directly Start with BO..

I am abap certified and have not worked on BI, Can i directly start with BO and how difficult for me to be a BO consultant. Is BO is having great future? Please suggest.
Thanks in advance.
Edited by: Mr. Dilip Shukla on Sep 23, 2009 4:38 PM

Hi Petric,
sorry for the questions, it's clear what you mean now. After some researches i can tell you, that it is the best solution to use the EnDat Signals is the cRIO EnDat Modul of SEA. National Instruments doesn't offer EnDat Modules, because we can't cover the whole spectrum of Modules and the EnDat Protocoll/Signal is very special and complicated. It ensures you reliable FPGA speed at a maximum data rate of 38 kHz and is a qualified product which is full supported from our cRIO Chassis. So if you want to use the EnDat Signal i would recommend you the Module from SEA. If it's possible to use other Signals like SSI, Hiperface you can look after other solutions.
EnDat 2.2 - Bidirectional Interface for Position Encoders
http://www.heidenhain.co.uk/de_EN/php/documentation-information/documentation/brochures/popup/media/...
I hope I could help you with your question.
Kind Regards,
Joaquin

Similar Messages

I am trying to update my iPod but I can't until I sync it. However when i try to sync it a message pops up and says "Blythes iPod" can not be synced because a session can not be started with this device. What do I do? Help!

I am trying to update my iPod but I can't until I sync it. However when i try to sync it a message pops up and says "Blythes iPod" can not be synced because a session can not be started with this device. What do I do? Help!

https://support.apple.com/kb/TS1567
Ah, it has been mentioned daily esp since iOS 5 / iTunes 10.5 but has always been there as an issue.
Order of attempts:
Repair the installers
Uninstall EVERY Apple component (auto and manual)
Services: Restart all 3 Apple items (AMS, Bonjour, iPod)
I* always do the last almost, then launch iTunes, and only then connect iPod.
IF you see a yellow alert in Devices and Printers or in Device Manager, then I could find NO WAY to fix or repair other than a clean OS. Something messed up the device driver support.
If/when Windows asks "what to do when it detects iPod"? don't chose any default action, to me, based on hunch and 3 PCs, that seems to mess AMS up for some reason.
Tried with Windows 7 64-bit Pro and Home Premium, and also Deve Preview 8 (which other than the inability to update iOS to 5.0 seems to run better -- except when it comes to AMS thing! so seems Apple is not on the same page writitng drivers.

How can i get started with messaging in java

how can i get started with messaging in java

If you're talking about writing mail clients in java, you might want to start with a better forum. We're focused on Messaging Servers, here. Unlikely you'll get any Java programming from us.
If you're talking about Messaging Server, start by downloading the software from sun.com/downloads.

G3 Lombard - Can't get started with anything except OS 8.6.

Hi,
I just bought a used Mac Bronze keyboard (Lombard). It was working great until i fixed it. (Yikes) By fixing it i mean I installed my software OS 9, and some other things that work on my 3400c. The Lombard didn't like that (OS 9.0) and wouldn't start. The Lombard Only boots with OS 8.6. After confirming that the CD reader was working fine. My Lombard would not start up with the OS 9 CD. (Flashing folder and question mark) Hmmmm Very strange. It also wouldn't go into SCSI hard disc mode. So I put the hard drive in my Mac 3400c and it worked fine. Hard disc mode and everything. While in Hard Disk Mode on the 3400c i put the OS 8.6 system and the finder back into the same folder and started up my Lombard. Perfect. It worked great. NOT leaving well enough alone I used the Norton disc utils on the hard drive. It fixed a few things and said it couldn't fix this last thing (i hit ok too quick to read what it couldn't fix). It also wouldn't start with the hard drive from the 3400c. (OS 9) Or even the hard drive from my Blue and white also OS 9. Any ideas?

OK i took the 8.6 system folder off the hard drive and replaced it with the 9.0 system folder.
Sorry, but I still don't understand clearly where an OS 9 System Folder came from, if you weren't able to start the Lombard with the installer disc. So which of these did you do:
Did you boot the 3400 to the installer disc, with the Lombard connected in SCSI Disk Mode, and then run the installer to install OS 9 onto the Lombard's hard drive? If so, the installation was tailored to the hardware of the 3400, because it was the host computer. That installation would be no more appropriate to boot the Lombard than the OS on the 3400's own hard drive is — and you know (now that you've tried it) that the 3400's drive doesn't boot the Lombard. In SCSI disk mode, the installer has no idea that the target disk is even part of another computer, never mind any information about the rest of that computer's hardware configuration. All it sees is the disk, and it assumes that that disk will be used to boot the host computer — exactly as if it were inside the host computer.
OR
Did you simply copy the System Folder from the installer disk (without actually running the installer) to the Lombard via SCSI Disk Mode? That wouldn't work either: the SF on an installer disk is only bootable when it resides on that disk. A copy of it moved elsewhere will rarely if ever boot any Mac.
OR
What other possibility is there? I can't think of another, but maybe you did. If so, what was it?

Can't get started with Reports

How do I run 9iAS Reports (Sun Solaris 8)? I am thoroughly lost and confused.
I've installed 9iDS and am able to start up the jdeveloper. How do I get going
with Reports? Do I need 9i Database to be installed? Can I use 8i Database?
I have 8.1.7.3.0 of the Database and 1.0.2.2.0 of the 9iAS installed.
When I try 9iDS/bin/rwbuilder or rwserver, it says that I'm missing
the reports.sh file.
I've spent half a day looking for this kind of information - pleas help!
Thanks,
Brian Kulman

More info: I am able to start the Reports Server by using "reports60_server start"
from my $IAS_HOME/6iserver/ directory. But I seem to be blind as to what
the next step is...

Can't get started with Elements 10

I recently loaded Adobe Premiere Elements 10 into my PC, Windows 7. Every time I try to start a project, I get the following message:
"Adobe Premiere Elements 10 has stopped working. A problem caused the program to stop working correctly. Windows will close the program and notify you if a solution is available. Close program."
I've gotten no response from Windows other than saying the program is incompatible. Then, I close the program and it shuts down.
Please advise.

1 - moved from the Premiere Pro forum
2 - From the Premiere Elements Information FAQ http://forums.adobe.com/thread/1042180
•You MUST use an account with Administrator Privileges to run Premiere Elements
•(Doing Run as Administrator http://forums.adobe.com/thread/969395 [says Encore and also for "All" versions of Premiere] will sometimes fix "odd" errors)
•What version of Premiere Elements? Include the minor version number (e.g., Premiere Elements 12 with the 12.0.1 update).
•What operating system? This should include specific minor version numbers, like "Mac OSX v10.9.4"---not just "Mac"
•Has this ever worked before? If so, do you recall any changes you made to Premiere Elements, such as adding Plug-ins, brushes, etc.? Did you make any changes to your system, such as updating hardware, printers or drivers; or installing/uninstalling any programs?
•Have you installed any recent program or OS updates? (If not, you should. They fix a lot of problems.)
•What kind(s) of image file(s)? When talking about camera raw files, include the model of camera.
•If you are getting error message(s), what is the full text of the error message(s)?
•What were you doing when the problem occurred?
•What other software are you running?
•Tell us about your computer hardware. How much RAM is installed? How much free space is on your system (C:) drive?
•How many and what speed are your hard drive(s)... ie 5400rpm or 7200rpm or?
And some other questions...
•What are you editing, and does your video have a red line over it BEFORE you do any work?
•Which version of Quicktime do you have installed?
•What is your exact brand/model graphics adapter (ATI or nVidia or ???)
•What is your exact graphics adapter driver version?
•Have you gone to the vendor web site to check for a newer driver?
•For Windows, do NOT rely on Windows Update to have current driver information
•-you need to go direct to the vendor web site and check updates for yourself
•ATI Driver Autodetect http://support.amd.com/en-us/download/auto-detect-tool
•nVidia Driver Downloads http://www.nvidia.com/Download/index.aspx?lang=en-us
3 - IF you have Premiere Elements version 10 and an nVidia card
•nVidia Driver Rollback PreElements-10 http://forums.adobe.com/thread/1317675
•-Old Drivers http://www.nvidia.com/Download/Find.aspx?lang=en-us

Bt/yahoo and apple ME, both wont send emails but can receive. Started with constantly asking for password but when entered never able to send.

I am using OS X 10.7.5 I ahve BT Infinity and use there email along with ME
Although I can receive emails I cant send any. I am asked for a password but it makes no difference. smtp list states all (bt & me) off line. Contacted bt who are no help!
I have checked that I can send on BT/yahoo direct.
Tried deleting and re-adding account.
Please help otherwise I will have to go back to BT and pay to fix there problem!

Hi there,
You may want to take a look at some of the troubleshooting steps found in the article below.
iOS: Unable to send or receive email
http://support.apple.com/kb/ts3899
-Griff W.

Can I directly communicate with an EnDat Sensor or do I need an interface?

We are using cRIO with FPGA and some DIO interfaces (NI 9411 and NI 9403). Until now we had incremental signals which are easy to detect with the DI module. But now we are have an absolute signal with this EnDat signal. Is there a way to add this signals (1Vss) ant the absolute ENDat interface with standard cRIO modules? We don't want to add an additional third party module as the EnDat Module from SEA.
Od do ou have other references to get an absolute signal?
Thanks
Solved!
Go to Solution.

Hi Petric,
sorry for the questions, it's clear what you mean now. After some researches i can tell you, that it is the best solution to use the EnDat Signals is the cRIO EnDat Modul of SEA. National Instruments doesn't offer EnDat Modules, because we can't cover the whole spectrum of Modules and the EnDat Protocoll/Signal is very special and complicated. It ensures you reliable FPGA speed at a maximum data rate of 38 kHz and is a qualified product which is full supported from our cRIO Chassis. So if you want to use the EnDat Signal i would recommend you the Module from SEA. If it's possible to use other Signals like SSI, Hiperface you can look after other solutions.
EnDat 2.2 - Bidirectional Interface for Position Encoders
http://www.heidenhain.co.uk/de_EN/php/documentation-information/documentation/brochures/popup/media/...
I hope I could help you with your question.
Kind Regards,
Joaquin

How can i get started with iChat

How can I get to talk to a friend who uses @mac.com if I log in with my gmail account?

While we all have MacBooks in this forum not all of us use iChat. There's a iChat Support Community where everybody uses iChat. You should also post this question there to increase your chances of getting an answer.
https://discussions.apple.com/community/applications/ichat

Can't get started with Metrowerks on Win98

I am having trouble writing anything more than a trivial program using the Metrowerks IDE on Win98. I have asked for help on the Metrowerks newsgroup but there appears to be a lack of expertise.
If I attempt to go in through the low level interface, creating the java code myself, the code compiles cleanly and creates a .jar file, but when I attempt to execute my class I get a class not found error message.
On the other hand if I try to go in through the high level interface, where the GUI creates the source code based upon my dragging and dropping components onto the screen, I lack control of exactly what is generated, and in any event the entire process craps out when I try to save the code.
I have been trying this with the 1.1.6 level of java which came with the Metrowerks compiler. I am in the process of downloading the 1.3 level.
I would appreciate it if somebody would tell me what I am supposed to do to actually compile and execute java programs in this environment, because this is creating a complete block to my learning java.

Jcobban,
What version of CodeWarrior are you using? Only version 6 and 7 will support JDK 1.3.
There should be a version of a JDK on the disk, install that one.
Let me know if you need any other help!
Cheers,
Chris

Can't get started with Airport Express; WPA2 problem?

Howdy,
I purchased an airport express about a month ago and am unable to get it set up, at all. My goal is what the setup guide calls "Using AirPort Express on an existing wireless network and stream music to powered speakers" (pg. 15 for those who have the book). The failure is that Airport Admin Utility doesn't recognize my third party wireless network.
My wireless hub is a linksys wireless-G cable gateway, and has been in use with multiple computers in the current setup for a couple years. It is setup with WPA2 personal, TKIP+AES encryption, and MAC access list enabled. SSID broadcast is currently enabled.
I am running OSX10.4.11 on the computer that I am using to attempt to configure this.
Following the instructions for "Connecting to an Existing Wireless Network" (pg 25), I am attempting to use Airport Utility. But there is no such program on my computer, so I am assuming that Airport Admin Utility is what the book refers to as Airport Utility. Airport Admin Utility presents a "window titled Select Base Station" but lists no base stations. I click "Other", provide the IP address and password, hit OK, and ... nothing happens. After 20 seconds the beachball appears, and after another 20 seconds it says "The airport admin utility was unable to read the configuration of the selected base station".
The IP address I used is the one that I enter into the web browser to access the linksys box (no secret here, 192.168.0.1). The password is the one used to access those settings (e.g., the linksys default is "admin", but I changed it). I know the IP address and password are correct, but I do not know if this is the IP address and password the program is asking for. I don't even know if I am running the correct program!
Thanks for any help,
Bob H

Actually, I have it working now.
What I did after posting my last message was I connected the AE to my wireless hub, via ethernet cable. Then Airport Utility was able to find it, initialize it, and load new firmware into it ("it" being the AE). During initialization stage I told it it would be connecting wirelessly to an existing wireless network, and I gave it the network name, security options and password.
Then I told the wireless hub to allow this device (MAC address = Airport ID), disconnected the ethernet cable, power-cycled the wireless hub, and relaunched Airport Utility. It saw the AE, so I quit that. Then I launched iTunes and selected my AE as the speakers. It told me I needed to enable iTunes Music Sharing in my firewall. After doing that, iTunes is now playing through my external speakers. Exactly what I want.
Now I just need to go set this up on my laptop, with the AE and speakers on the other side of the house where I want 'em.
As a recap, I think I basically had two problems, both related to documentation. First, the program that the Setup Guide tells me to use wasn't in my Tiger applications folder, and I was fooled by a program with a similar name (in the past I have seen such name changes between what the setup guide said I should use and what I really needed to use). Second, it wasn't clear to me that, regardless of how I wanted to configure things for usage, I needed to establish a valid wired connection to the AE to initialize it. I think that could be made clearer in the book.
Thanks for everyone's help.
Bob H

Can't Get Started With CF or DW

I'm very very new to DW 8 and CF MX7. XP Pro SP2. I got both
installed on my computer for local testing. I just can't make
anything work. I created a local server, several in fact, In DM
I've created several test servers. Nothing works. When I try to
preview a simple hello world cfm file I either get the I have to
create a testing server prompt and/or I get the open/save ie option
which opens my cfm file in notepad. or page not found.
I know I'm just being newbee stupid. Are there any idiot
proof install/setup instruction floating around?
Thanks Much
John

It sounds like you have Coldfusion set up to use its own
internal server. Here's what you can do:
1. Look for C:\CFusionMX7\wwwroot
2. Create a folder named "Test' there:
C:\CFusionMX7\wwwroot\Test\
3. Create a cfm page that says something like "Hello World"
in the body. Name the CFM Page "helloworld.cfm"
4. Open up IE Explorer and enter the following url:
http://127.0.0.1:8500/Test/helloworld.cfm
See if the page pulls up correctly

How can I directly communicate with an apple employee or app developer about improving the "reminders" app. I have a few suggestions that I think have what it takes to work themselves into a new update!

I just want to email someone who can actually change the app for the better in the next update

http://www.apple.com/feedback/iphone.html

Can't get started with Adobe exportPDF! What to do?

I use Acrobat Reader on my iPad. I bought Adobe exportPdf from within the program and I received a confirming mail. Still When I try to use the exportPDF tool I am linked to the Purchase Adobe ExportPDF again. I have tried to log out from Adobe Reader but IT didn't help. Andy suggestions.

I am having the same issue- some please help!

Can I use operator to view a scenario started with startscen.sh

Can a scenario started with startscen.sh be seen within operator? I run the scenario and the execution does not show up in operator.

All executions are shown in the operator. If it does not appear, then your odiparams file, which is read when you use startscen from the os, must be pointing to another repository.

Can i directly Start with BO..

Similar Messages

Maybe you are looking for