Can I enable 802.11b/g on individual radios instead of globally?

I am deploying 400 new APs. There is an existing wireless network. I need to turn up some of the radios before I turn up the rest. Right now I have 802.11b/g network turned off globally across all controllers. What I want to know is can I enable 802.11b/g radios selectively on individual APs or does it have to be done globally across the controller?
Thanks.

Hi Friend,
The only workaround is globally enable for all APs and manually admin down for respective APs for b/g radio. I agree its a tough job when you have 400 APs but if you can run some script it will be a matter of seconds.
And if you have WCS you can use AP template for that purpose which again will take less time than manual work.
Regards,
Ankur

Similar Messages

  • Help Enabling 802.11b Support

    Can anyone help? All I want to do is enable 802.11b support on my Cisco 877W. My 802.11g clients can see and attach to it no problems. My 802.11b clients cannot see it at all. I have tried all sorts but nothing has helped. My config looks like this:
    interface Dot11Radio0
    no ip address
    encryption key 1 size 128bit 7 BC48CE99C4E9B683819990D3C1A5 transmit-key
    encryption mode wep mandatory
    ssid *****
    authentication open
    speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0
    48.0 54.0
    station-role root
    no dot11 extension aironet
    bridge-group 1
    bridge-group 1 spanning-disabled
    What do I need to add to make it visible and available to 802.11b clients?
    Many Thanks,
    Matt

    I'd start by defaulting the AP back to factory default, no WEP, no authentication.
    Check to see if the 802.11b clients can connect.
    If all the 802.11b clients are running the same software, check to see that they are up-to-date drivers & client software. If you're using the MS client software (Zero Wireless Config) try a client using the vendor's client software instead.
    If the clients are not eve associating, look at the basic parameters: things like preamble length (legacy default is "long" which is a one meg data rate)
    If you can get the 802.11b client to connect whith all open parameters, then add WEP. Be advised that some clients need the WEP entered as HEX, not ASCII.
    For example ASCII "ABCD" would be "41 42 43 44" in hex ... make sure you're using the same system. IF youre using something like "12345abcde" that can be a valid (but incorrect) hex string when ou really intend for it to be ASCII.
    Also note that leading or training spaces (ASCII 20) are valid characters. Make sure you do not have leading or training spaces in your WEP (unless you really want them there, in whch case, make sure they're there)
    Make sure the Ethernet format is correct: use the Web GUI to set up. Check the parameters on the "Interfaces" page and do not (at least initially) use the "Best throughput" or "Best Range" settings, leave it at "Default Settings"
    If your 802.11b clients are PDAs, bar-code scanners, or other hand-held devices, check that they are at default settings for the standard 802.11b protocols; some use proprietary protocols for better performance or security.
    That's about it for me ... let us know if any of that changes (works / doesn't work, but acting differently / doesn't work, looks the same).
    Good Luck
    Scott

  • Can not enable 802.11n on my MacBook (Core 2 Duo) running Snow Leopard.

    My MacBook has the AirPort card saying "a/b/g", so I know that it is not yet n-enabled.
    It is INDEED a Core 2 Duo.
    It is running Snow Leopard.
    When I try install the enabler off of my "AirPort Extreme: 802.11n Wi-Fi Wireless Base Station" disc, it tells me that "This volume does not meet the requirements for this update.".
    Is there ANYTHING that I can do?
    Information from System Profiler:
    *Hardware Overview:*
    Model Name: MacBook
    Model Identifier: MacBook2,1
    Processor Name: Intel Core 2 Duo
    Processor Speed: 2.16 GHz
    Number Of Processors: 1
    Total Number Of Cores: 2
    L2 Cache: 4 MB
    Memory: 3 GB
    Bus Speed: 667 MHz
    Boot ROM Version: MB21.00A5.B07
    SMC Version (system): 1.17f0
    Interfaces:
    en1:
    Card Type: AirPort Extreme (0x168C, 0x86)
    Firmware Version: Atheros 5424: 2.0.19.8
    Locale: FCC
    Country Code: CA
    Supported PHY Modes: 802.11 a/b/g
    Supported Channels: 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165

    en1:
    Card Type: AirPort Extreme (0x168C, 0x87)
    Firmware Version: Atheros 5416: 2.0.19.8
    Locale: FCC
    Country Code: TW
    Supported PHY Modes: 802.11 a/b/g/n
    So i just bought a wrt160n router...according to the above settings am I able to take advantage of N?? I actually had no idea as this came as a suprise to me. haha..All i know is the N enabler software will not work...

  • Disable 802.11b/g

    Can i disable 802.11b/g in my new Time Capsule that supports 802.11ac? Ultimaltely I want to disable all standards under 802.11ac (when iPhone/iPad finally supports it)
    I have read old wifi standards slows downs routers/acess points etc.

    Can i disable 802.11b/g in my new Time Capsule that supports 802.11ac?
    Sorry, but no.
    Whlle you could customize and maximize previous versions of the Time Capsule, Apple has "upgraded" things by removing the settings that would allow this in the "new" Time Capsule.

  • AP with 802.11 G Vs clients with 802.11b

    hi
    i've got more access point 1200 series with he 802.11g but the client are 802.11b . Can the client 802.11b connect at the AP with 802.11 G ? Now i don't resolve this problem anche the client 802.11b connect only with the ap 1200 series with 802.11b
    Thanks for all

    > If you disable the "b" data rates, you've pretty much blocked "b" clients.
    A-ha... As i can understand i must disable 1.0, 2.0, 5.5 and 11.0 speed's.
    "To set the 2.4-GHz, 802.11g radio to serve only 802.11g client devices, set any Orthogonal Frequency Division Multiplexing (OFDM) data rate (6, 9, 12, 18, 24, 36, 48, 54) to Basic."(c) Cisco IOS Software Configuration Guide for Cisco Aironet Access Points 12.3(7)JA
    This the same thing as entering `speed throughput ofdm`? Command disables all 802.11B data rates as you recommend.
    > They may be able to respond / attempt association (that all happens at either one or two mbps for either "b" or "g" ... long or short preambles), but since they dont have compatible data rates, they can never connect.
    I know... But, AFAIK, when 802.11G AP "see" 802.11B client in his coverage area AP "downgrades" to 802.11B to allow this client associacion. Your recommedation prevents this, i'm right? Try to understand me, many years i used damn D-Link (my boss love it) but one day i sad "Cisco or on no any kind wireless :E" and now i have dosens AP-1200 with my many questions... All want now i want - is set "G-only" (in dlink's terms) like function...
    Thank you
    P.S. Sorry for my english

  • Channel utilization - show ap auto-rf 802.11b

    Question on the command "show ap auto-rf 802.11b <ap_name>". What is the period of time that is measured for:
        Channel Utilization.......................... 64 %
    I am seeing high channel util. on certain AP's, but standing directly below the AP w/ spectrum analyzer, I see much lower util.%:
    Basically, wondering if the measurement is from the exact time I launch the command, or if it's over say a 10 sec. period?
    WLCCA shows highest Rx neighbor @ -71
    complete output of the command:
    (WiSM-slot8-1) >show ap auto-rf 802.11b ap-bhs-400-2
    Number Of Slots.................................. 2
    AP Name.......................................... ap-bhs-400-2
    MAC Address...................................... 50:57:a8:d6:7d:6d
      Slot ID........................................ 0
      Radio Type..................................... RADIO_TYPE_80211b/g
      Sub-band Type.................................. All
      Noise Information
        Noise Profile................................ PASSED
        Channel 1....................................  -88 dBm
        Channel 2....................................  -89 dBm
        Channel 3....................................  -91 dBm
        Channel 4....................................  -94 dBm
        Channel 5....................................  -93 dBm
        Channel 6....................................  -93 dBm
        Channel 7....................................  -90 dBm
        Channel 8....................................  -87 dBm
        Channel 9....................................  -94 dBm
        Channel 10...................................  -92 dBm
        Channel 11...................................  -92 dBm
      Interference Information
        Interference Profile......................... PASSED
        Channel 1.................................... -128 dBm @  0 % busy
        Channel 2.................................... -128 dBm @  0 % busy
        Channel 3.................................... -128 dBm @  0 % busy
        Channel 4.................................... -128 dBm @  0 % busy
        Channel 5.................................... -128 dBm @  0 % busy
        Channel 6.................................... -128 dBm @  0 % busy
        Channel 7.................................... -128 dBm @  0 % busy
        Channel 8.................................... -128 dBm @  0 % busy
        Channel 9.................................... -128 dBm @  0 % busy
        Channel 10................................... -128 dBm @  0 % busy
        Channel 11................................... -128 dBm @  0 % busy
      Load Information
        Load Profile................................. PASSED
        Receive Utilization.......................... 0 %
        Transmit Utilization......................... 1 %
        Channel Utilization.......................... 65 %
        Attached Clients............................. 0 clients
      Coverage Information
        Coverage Profile............................. PASSED
        Failed Clients............................... 0 clients
      Client Signal Strengths
        RSSI -100 dbm................................ 0 clients
        RSSI  -92 dbm................................ 0 clients
        RSSI  -84 dbm................................ 0 clients
        RSSI  -76 dbm................................ 0 clients
        RSSI  -68 dbm................................ 0 clients
        RSSI  -60 dbm................................ 0 clients
        RSSI  -52 dbm................................ 0 clients
      Client Signal To Noise Ratios
        SNR    0 dB.................................. 0 clients
        SNR    5 dB.................................. 0 clients
        SNR   10 dB.................................. 0 clients
        SNR   15 dB.................................. 0 clients
        SNR   20 dB.................................. 0 clients
        SNR   25 dB.................................. 0 clients
        SNR   30 dB.................................. 0 clients
        SNR   35 dB.................................. 0 clients
        SNR   40 dB.................................. 0 clients
        SNR   45 dB.................................. 0 clients
      Nearby APs
        AP 00:0f:90:5e:2a:d0 slot 0..................  -73 dBm on  11 (10.252.1.2)
        AP 00:13:5f:56:e0:90 slot 0..................  -88 dBm on  11 (10.252.1.4)
        AP 00:13:5f:57:00:70 slot 0..................  -79 dBm on   1 (10.252.1.4)
        AP 00:16:9c:91:64:e0 slot 0..................  -43 dBm on  11 (10.252.1.2)
        AP 00:17:0f:db:2e:70 slot 0..................  -87 dBm on   1 (10.252.1.2)
        AP 00:17:df:35:43:90 slot 0..................  -90 dBm on   1 (10.252.1.10)
        AP 00:21:d8:d5:a2:40 slot 0..................  -91 dBm on   1 (10.252.1.12)
        AP 00:21:d8:d5:a8:90 slot 0..................  -91 dBm on   1 (10.252.1.12)
        AP 00:21:d8:d5:a8:c0 slot 0..................  -91 dBm on  11 (10.252.1.12)
        AP 00:21:d8:d5:ac:80 slot 0..................  -92 dBm on   1 (10.252.1.12)
        AP a4:56:30:5d:b0:a0 slot 0..................  -89 dBm on  11 (10.252.1.12)
        AP b4:e9:b0:b3:c8:70 slot 0..................  -91 dBm on  11 (10.252.1.18)
      Radar Information
      Channel Assignment Information
        Current Channel Average Energy...............  -76 dBm
        Previous Channel Average Energy..............  -57 dBm
        Channel Change Count......................... 3
        Last Channel Change Time..................... Wed Jul 17 22:27:37 2013
        Recommended Best Channel..................... 1
      RF Parameter Recommendations
        Power Level.................................. 1
        RTS/CTS Threshold............................ 2347
        Fragmentation Threshold...................... 2346
        Antenna Pattern.............................. 0
      Persistent Interference Devices
      Class Type                 Channel  DC (%%)  RSSI (dBm)  Last Update Time
      All third party trademarks are the property of their respective owners.
    These are lined down a hallway (about 50' from ea. other). Looks to me like they are set for too high Tx and crowding chan. 1. I'll figure out the reason for that.
    show advanced 802.11b txpower:
    ap-bhs-400-1                     *1         *1/7 (22 dBm) [22/19/16/13/10/7/4/4]
    ap-bhs-400-2                     *1         *1/7 (22 dBm) [22/19/16/13/10/7/4/4]
    ap-bhs-400-3                     *11        *1/8 (23 dBm) [23/20/17/14/11/8/5/2]
    ap-bhs-400-4                     *1         *1/7 (22 dBm) [22/19/16/13/10/7/4/4]
    ap-bhs-400-5                     *11        *7/8 ( 5 dBm) [23/20/17/14/11/8/5/2]
    ap-bhs-400-6                     *1         *1/7 (22 dBm) [22/19/16/13/10/7/4/4]
    ap-bhs-451-1                     *6         *7/8 ( 5 dBm) [23/20/17/14/11/8/5/2]

    Cool thx. Guessing "Load Interval". Looks like 60 seconds is the answer. Including output here for others...
    show advanced 802.11b monitor
    Default 802.11b AP monitoring
      802.11b Monitor Mode........................... enable
      802.11b Monitor Channels....................... Country channels
      802.11b RRM Neighbor Discovery Type............ Transparent
      802.11b AP Coverage Interval................... 180 seconds
      802.11b AP Load Interval....................... 60 seconds
      802.11b AP Noise Interval...................... 180 seconds
      802.11b AP Signal Strength Interval............ 60 seconds
      802.11b AP Neighbor Report Interval............ 180 seconds
      802.11b AP Interference Report Interval........ 120 seconds

  • Will 2800-400 BIOS update enable 802.11g wireless LAN?

    I recently bought a Belkin 54G cardbus wireless adapter for use with my Satellite 2800-400, which has a Windows ME OS.
    The setup software wouldn't install a driver, even though ME was said to be supported.
    I wrote to Belkin and they told me that it was because the laptop BIOS didn't support 802.11g wireless and that I should update the BIOS. I updated to BIOS version 2 but it didn't make any difference.
    I don't know if Belkin's instructions were on the right track or whether they were they just pushing the responsibility as far away from themselves as they could.
    Please can anyone tell me if my laptop does support 802.11g wireless, with or without the BIOS upgrade?
    TIA
    Mike

    > Hi
    >
    > Im not 100% sure if your notebook supports a
    > wireless LAN connection because I dont found any
    > informations about it.
    Thanks for the reply. the notebook does support wireless LAN because I can get a 802.11b card to function OK.
    > But as far as I know its not
    > necessary to update the BIOS therewith the Wireless
    > card works.
    Well it's done now so there may be other benefits. Not 802.11g wireless though it seems.
    > I recommend to contact the service partner. They have
    > more detailed informations about this unit.
    Thanks I'll try to find and contact a service partner.
    Mike

  • Enable only 802.11b for a single WLAN?

    I have only 802.11b client in my production environment (PLC, serial converter, ecc..).
    On my WLC how can I configure a single WLAN 802.11b only and other WLAN with all-mode enable?
    Regards.
    Mirko S.

    Sorry, there is a band 802.11g, 802.11b/g but not 802 .11b.
    Is correct?
    In this time I had to set the datarate 1, 2, 5.5 and 11M.
    I do not think it's the right solution.
    Regards.
    Mirko S.

  • Can I replace my 802.11b Aitport card ?

    Can I replace the older 802.11b Airport card in my Titanium G4,OSX 10.3.x, with a newer "g" or "n" card so that it will connect to a new netgear router? And where should I go to purchase one if it's possible?

    Can I replace the older 802.11b Airport card in my Titanium G4,OSX 10.3.x, with a newer "g" or "n" card so that it will connect to a new netgear router?
    Any compatible 802.11g or 802.11n cards will be PC Cards or external components such as the AeroPad mini. The internal 802.11b card isn't upgradable.
    (55221)

  • How can I use the Time Capsule in only 802.11b/g?

    I think I am getting interferences on my 5GHz phone from the time capsule, which I have running in 802.11n mode with b/g compatitibility. I assume if the Time Capsule was running in 802.11b/g mode I would not get the intereferences?
    The Airport utility does not seem to have a setting to use the Time Capsule in 802.11b/g only. Is there a way to accomplish this?
    Message was edited by: Karl R.

    Duane wrote:
    Then the Time Capsule's 5 GHz network should not interfere with the phone since it operates a long way from the phone's frequency.
    Not necessarily. In the US 802.11n channels appear to go up to at least 5.805 GHz, if I interpret this chart
    http://www.networkdictionary.com/Wireless/Wi-Fi-Wireless-LAN-Frequency.php
    correctly.
    It would seem that the best way to avoid interference with 5.8 GHz cordless phones is to avoid channels above 153.

  • D-link router DIR-615, Can't access internet with Airport Wireless 802.11B

    It is a known issue with many Dlink routers that with the router wireless settings on "802.11 B,G,N" it will NOT work with your G3/ some G4 wireless cards that ONLY support 802.11B.
    Enter 192.168.0.1 in your address bar to access your Dlink router. Go to settngs....wireless settings...
    Go to your router settings and select "802.11B" ONLY or "802.11 B and G". This will solve the problem. D-link is aware.
    I was told they will be coming out with updated firmware to correct the issue.

    It's almost better to have a 2nd router for the older B cards anyway because running in multi mode with the 615, it's not a dual band device, so you won't see any speed benefits in G or N. better to run B/G anyway.

  • Client got not connection to wlan over wlc 2504 on 802.11b/g

    Hi everybody,
    We are using a wlc 2504 with 7.6.100.0 and AP 1532e.
    I have the strange observacion that only clients with 802.11n (2.4GHz) can connect to the WLAN. Clients thats works only with 802.11b/g, they can't connect to the WLAN. Affected are all machines which want to connect with 802.11b/g.
    This is a MESH WLAN with 5GHz backhaul and 2.4GHz for the user.
    During the debugging found the following:
    *apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:44:40.581: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.584: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:44:40.585: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:42.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:42.649: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:44.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:44.649: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:44.650: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:46.649: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 1
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:44:46.649: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:44:52.083: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:44:52.084: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:44:52.087: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:54.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:54.249: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:56.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:44:56.249: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:44:58.249: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 2
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:44:58.249: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:44:58.250: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:03.768: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:03.769: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:03.770: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:03.772: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 Allocating EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:03.773: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:05.849: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:05.849: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:07.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:07.849: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:09.848: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 3
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Blacklisting (if enabled) mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to START (0) last state 8021X_REQD (3)
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Reached FAILURE: from line 5274
    *dot1xMsgTask: May 09 11:45:09.849: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 9) in 10 seconds
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:15.689: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Initializing policy
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 START (0) Change state to AUTHCHECK (2) last state START (0)
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:15.690: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:15.691: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.693: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.694: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Reassociation received from mobile on BSSID 18:9c:5d:71:34:50
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Global 200 Clients are allowed to AP radio
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Max Client Trap Threshold: 0  cur: 1
    *apfMsConnTask_4: May 09 11:45:15.875: 00:1b:77:b4:34:e0 Rf profile 600 Clients are allowed to AP wlan
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Interface policy on Mobile, role Unassociated. Ms NAC State 2 Quarantine Vlan 0 Access Vlan 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Re-applying interface policy for client
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv4 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2202)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Changing IPv6 ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:2223)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfApplyWlanPolicy: Apply WLAN Policy over PMIPv6 Client Mobility Type
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4795 setting Central switched to TRUE
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 In processSsidIE:4798 apVapId = 1 and Split Acl Id = 65535
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying site-specific Local Bridging override for station 00:1b:77:b4:34:e0 - vapId 1, site 'default-group', interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Applying Local Bridging Interface Policy for station 00:1b:77:b4:34:e0 - vlan 1, interface id 12, interface 'catodos'
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE  statusCode is 0 and status is 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 processSsidIE  ssid_done_flag is 0 finish_flag is 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (8): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 suppRates  statusCode is 0 and gotSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 STA - rates (12): 2 4 11 22 12 18 24 36 48 72 96 108 0 0 0 0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 extSuppRates  statusCode is 0 and gotExtSuppRatesElement is 1
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Processing RSN IE type 48, length 20 for mobile 00:1b:77:b4:34:e0
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Initializing policy
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Change state to AUTHCHECK (2) last state 8021X_REQD (3)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 AUTHCHECK (2) Change state to 8021X_REQD (3) last state AUTHCHECK (2)
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Central switch is TRUE
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 Not Using WMM Compliance code qosCap 00
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 0.0.0.0 8021X_REQD (3) Plumbed mobile LWAPP rule on AP 18:9c:5d:71:34:50 vapId 1 apVapId 1 flex-acl-name:
    *apfMsConnTask_4: May 09 11:45:15.876: 00:1b:77:b4:34:e0 apfPemAddUser2 (apf_policy.c:333) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfPemAddUser2:session timeout forstation 00:1b:77:b4:34:e0 - Session Tout 1800, apfMsTimeOut '1800' and sessionTimerRunning flag is  0
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 49) in 1800 seconds
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Func: apfPemAddUser2, Ms Timeout = 1800, Session Timeout = 1800
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 Sending Assoc Response to station on BSSID 18:9c:5d:71:34:50 (status 0) ApVapId 1 Slot 0
    *apfMsConnTask_4: May 09 11:45:15.877: 00:1b:77:b4:34:e0 apfProcessAssocReq (apf_80211.c:8292) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Associated
    *spamApTask6: May 09 11:45:15.878: 00:1b:77:b4:34:e0 Sent 1x initiate message to multi thread task for mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Creating a PKC PMKID Cache entry for station 00:1b:77:b4:34:e0 (RSN 2)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Adding BSSID 18:9c:5d:71:34:50 to PMKID cache at index 0 for station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: New PMKID: (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Initiating RSN PSK to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAP-PARAM Debug - eap-params for Wlan-Id :1 is disabled - applying Global eap timers and retries
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 dot1x - moving mobile 00:1b:77:b4:34:e0 into Force Auth state
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 EAPOL Header:
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00000000: 02 03 00 5f                                       ..._
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Found an cache entry for BSSID 18:9c:5d:71:34:50 in PMKID cache at index 0 of station 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: Including PMKID in M1  (16)
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879:      [0000] f6 3d 52 9f 2a de 52 90 1d a2 46 49 0f 14 f6 69
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Starting key exchange to mobile 00:1b:77:b4:34:e0, data packets will be dropped
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Sending EAPOL-Key Message to mobile 00:1b:77:b4:34:e0
       state INITPMK (message 1), replay counter 00.00.00.00.00.00.00.00
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 Reusing allocated memory for  EAP Pkt for retransmission to mobile 00:1b:77:b4:34:e0
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *Dot1x_NW_MsgTask_0: May 09 11:45:15.879: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:18.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 Retransmit 1 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:18.049: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:20.049: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 Retransmit 2 of EAPOL-Key M1 (length 121) for mobile 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0 mscb->apfMsLwappLradNhMac = 78:da:6e:59:c9:8c mscb->apfMsLradSlotId = 0 mscb->apfMsLradJumbo = 0 mscb->apfMsintIfNum = 1
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  mscb->apfMsBssid = 18:9c:5d:71:34:50 mscb->apfMsAddress = 00:1b:77:b4:34:e0 mscb->apfMsApVapId = 1
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  dot1xcb->snapOrg = 00 00 00 dot1xcb->eapolWepBit = 0 mscb->apfMsLwappLradVlanId = 0 mscb->apfMsLwappMwarInet.ipv4.addr = -1062679171
    *dot1xMsgTask: May 09 11:45:20.049: 00:1b:77:b4:34:e0  mscb->apfMsLwappMwarPort = 5246 mscb->apfMsLwappLradInet.ipv4.addr = -1062679163 mscb->apfMsLwappLradPort = 40089
    *osapiBsnTimer: May 09 11:45:22.048: 00:1b:77:b4:34:e0 802.1x 'timeoutEvt' Timer expired for station 00:1b:77:b4:34:e0 and for message = M2
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Retransmit failure for EAPOL-Key M1 to mobile 00:1b:77:b4:34:e0, retransmit count 3, mscb deauth count 0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Resetting MSCB PMK Cache Entry 0 for station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Removing BSSID 18:9c:5d:71:34:50 from PMKID cache of station 00:1b:77:b4:34:e0
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 0 ---> 8
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Sent Deauthenticate to mobile on BSSID 18:9c:5d:71:34:50 slot 0(caller 1x_ptsm.c:598)
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Setting active key cache index 8 ---> 8
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Deleting the PMK cache when de-authenticating the client.
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Global PMK Cache deletion failed.
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 57) in 10 seconds
    *dot1xMsgTask: May 09 11:45:22.049: 00:1b:77:b4:34:e0 Freeing EAP Retransmit Bufer for mobile 00:1b:77:b4:34:e0
    *osapiBsnTimer: May 09 11:45:32.048: 00:1b:77:b4:34:e0 apfMsExpireCallback (apf_ms.c:625) Expiring Mobile!
    *apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 apfMsExpireMobileStation (apf_ms.c:6632) Changing state for mobile 00:1b:77:b4:34:e0 on AP 18:9c:5d:71:34:50 from Associated to Disassociated
    *apfReceiveTask: May 09 11:45:32.049: 00:1b:77:b4:34:e0 Scheduling deletion of Mobile Station:  (callerId: 45) in 10 seconds
    Thanks for any advice

    In some of the big name brands of wireless, there is "no such thing" as 802.11n on a 2.4 Ghz.  No such thing because Cisco won't allow you (any more) to do channel bonding of 2.4 Ghz.  It doesn't make any sense to bond an already restricted 2.4 Ghz non-overlapping channel (three) and squeeze this number down to two.  
    Can you check to ensure that the data rates for 802.11b are enabled?  Maybe someone disabled data rates from 1 Mbps to 11 Mbps.

  • AE not working after upgrading to 802.11b/g/n AEBS

    I upgraded to the square 802.11b/g/n AEBS but have lost my AE which I use to play iTunes through my stereo. I just get the blinking yellow on the AE now and there's no longer a pulldown window in the lower right corner of iTunes for me to pick the output (i.e., Living Room.)
    I've updated the firmware in both the AEBS and AE. I've run the Airport Utility to make sure I'm getting out to the net via AEBS. But Airport Utility can't find AE.
    However, if I reset AE to its factory default, Airport Utility will see AE as having default settings and ask me to Update them. I go through the updating procedure (choosing one time to choose to join the existing AEBS network and at another time, to Create a New Network.)
    Both times the Airport Utility eventually will say AE has been successfully updated and go into restart. However, it hangs and after a few minutes says it can't fine ANY of my networks and for me to try again. (And again, and again.) I can get the AEBS back up every time but AE is still lost to me.
    Any suggestions as to how to get the older AE to work with the new AEBS?

    Hi,
    When a wireless network has a mixed environment of  802.11b clients and 802.11g clients, make sure that data rates 1, 2,  5.5, and 11 Mbps are set to required (basic) and that all other data rates are set to enable.  The 802.11b adapters do not recognize the 54 Mbps data rate and do not  operate if data rates higher than 11Mbps are set to require on the  connecting access point.
    here is the link which clarifies all your doubts.. and also tabular as well
    http://www.cisco.com/en/US/docs/wireless/access_point/12.4_21a_JA1/configuration/guide/scg12421aJA1-chap6-radio.html#wp1101903
    lemme know if this answered your question..
    Regards
    Surendra
    ====
    Please dont forget to rate the posts which answered your question and mark it as answered or was helpfull

  • Extreme AP doesn't show in 802.11B/G mode

    I'm using a macbook pro 2.0ghz, and just bought an 802.11n Airport Extreme.
    I have nothing new in software update control panel. I'm running 5.2.1 Airport Utility,
    My airport extreme has the green light, and via the ethernet port I can connect to the web.
    When I set it to 802.11N, I can see/connect to it wirelessly and get to the web.
    When I set it to 802.11B, I can't see the AP, or connect to it via manual join. But I can still connect over ethernet of course.
    None of my other laptops/iphone can't see it in 802.11B mode either. I do NOT have closed network enabled, it should be broadcasting for the world.
    So what gives? My airport 802.11B base station worked great (I unplugged it during this). But my 802.11N Extreme doesn't seem to work as 802.11B/G, even though it's a selectable option.
    Anyone else seeing this?

    Although it should change automatically when you change to 802.11b/g, verify that the radio mode is switching to 2.4 GHz.

  • Photosmart C7250 wireless 802.11b fails

    My new C7250 works well with USB and wired ethernet, but fails miserably (prints slowly, if at all) on my wireless 802.11b network.  All other devices work well on my wireless network.  I've spent many hours with HP and exhausted their first line support.  They supposedly have opened a case but I have heard nothing in a week.  Meanwhile, I took a network trace using WireShark and it shows a large number of retransmissions.  (I'm expert with application/network performance profiling.)  All you have to do is browse to http://192.168.1.xxx/ to test transmission -- don't even need to install drivers or printers to see the errors.  This problem appears to be with wireless support on the C7250.
    Has anyone experienced problems or success with 802.11b on this device?  How about 802.11g?  I would be willing to upgrade my wireless if I knew that it would resolve the problem.
    What does it take to escalate a probem with HP for resolution?

    All 2004 and newer wireless HP Inkjet printers are compatible with 802.11g and 802.11b networks (otherwise we couldn't get 802.11g Wi-Fi certification).  Besides testing for interoperability, we test for a minimum wireless throughput at the TCP layer.
    I'd like to see the internal connectivity report that you can generate by pressing the <setup> and <#> buttons simultaneously.  Scan the report to a memory card, copy it to your PC and post the image here.
    It will tell me information about your wireless network and other networks in the area.
    I have a couple of other questions:
    Does the slow printing go away after a power cycling the printer and then does it return later?
    Does the slow printing go away after a power cycling the wireless-router and then does it return later?
    Are you seeing retransmissions of TCP, 802.3 (ethernet) frames or 802.11 frames?  I wasn't sure at what layer you are sniffing the data at?
    What make and model 802.11b wireless-router are you using?
    Do you have encryption enabled?  Does disabling encryption change the speed of printing?
    How many wireless PC's (Macs?) to you have on your network?  Do they all exhibit slow printing?
    Have you changed the default fragmentation settings of your wireless-router?
    At home, I routinely get 1.5 Mbytes/sec transfer rates between my 802.11g wireless-routers and my HP printers and about 700 Kbytes/sec in 802.11b mode.
    One other thing you can try is to go to the printers internal web page, browse over to the Networking, Wireless, Advanced page and enable the configuration "In an infrastructure network use 802.11b behavior".
    Regards / Jim B
    Regards / Jim B / Wireless Enthusiasts
    ( While I'm an embedded wireless systems engineer at work, on this forum I do not represent my former employer, Hewlett-Packard, or my current employer, Microsoft )
    + Click the White Kudos star on the left as a way to say "thank you" for helpful posts.

Maybe you are looking for

  • Fed up with BT already, speed and usage.

    I've been with BT from the 1st of April, what a disaster. Many issues with slow speed, emailed support a few time and had a couple of phone calls back "We're looking into it, will call back withing 48 hours" they never do. My speed has varied from 35

  • How to control formatting of include text in smartform

    Hello Everyone - I have converted sales order acknowledgements from sapscript to smartform. I need to print material sales text at line level. Include text method is being used, it works in most cases. However, in some cases the Std Paragraph format

  • Use bridgeTalk with onError event, exception handling

    Hi all, I'm writting a function who use bridgeTalk to execute a photoshop script. This function works but I would like to throw an exception if the script has a problem. I commented a line in my script to have an exception but the onError event doesn

  • XI Message size - recommendation

    Hi, I have a question regarding the message size of xi payload. I'm working on a scenario, sending 1.500.000 datarows via client proxy to xi for further processing. as i don't wanna have 1.500.000 messages in xi, i want to group the messages. can you

  • HT1277 Old hotmail emails were transferred and deleted from online account

    All my old email from my hotmail account got TRANSFERRED to my mac mail and are no longer online. Not what I wanted to happen. Can I have them returned to my hotmail account and have the mail account mirror my online hotmail account?