Can I exceed the license count on a 5508 series WLAN controller?

Scenario:
5508 WLC licensed for 100 APs.
Currently have 78 APs on the controller.
Two buildings coming online this week, but there was a snafu with purchasing and license upgrade still in progress. 92 APs total between them.
I looked at the license on the WLC, and in there it has something listed for 500, but unused, or something like that, along with my 100 AP license in use.
I have never tried this, which is why I'm asking. What happens if I power up all those new access points? Will they join the WLC and run for 90 days or something to that effect? What is that 500 AP license? A demo?
Thanks in advance.

You are talking about the onboard factory evaluation licenses. You can put these in 'high' and resolve your deficiency while you get your perm licenses.
See below ..
http://www.cisco.com/c/en/us/td/docs/wireless/controller/7-4/configuration/guides/consolidated/b_cg74_CONSOLIDATED/b_cg74_CONSOLIDATED_chapter_011.html#d99529e920a1635
Activating an AP-Count Evaluation License
Information About Activating an AP-Count Evaluation License
If you are considering upgrading to a license with a higher access point count, you can try an evaluation license before upgrading to a permanent version of the license. For example, if you are using a permanent license with a 50-access-point count and want to try an evaluation license with a 100-access-point count, you can try out the evaluation license for 60 days.
AP-count evaluation licenses are set to low priority by default so that the controller uses the ap-count permanent license. If you want to try an evaluation license with an increased access point count, you must change its priority to high. If you no longer want to have this higher capacity, you can lower the priority of the ap-count evaluation license, which forces the controller to use the permanent license.
Note
To prevent disruptions in operation, the controller does not switch licenses when an evaluation license expires. You must reboot the controller in order to return to a permanent license. Following a reboot, the controller defaults to the same feature set level as the expired evaluation license. If no permanent license at the same feature set level is installed, the controller uses a permanent license at another level or an unexpired evaluation license.

Similar Messages

Exceeding ISE license counts - performance consequences?

Hello,
I have a customer that is running a 2-node ISE deployment and is licensed for 250 Base and 250 Adv. users.
We have moved the wired users over in one of their offices into Monitor Mode only, and the Base/Adv. Active license counts have exceeded both these values.
Long-term, what is the operational impact?
I understand from Chapter 7 of the ISE User Guide that "To avoid service disruption, Cisco ISE continues to provide services to endpoints that exceed license entitlement. Cisco ISE instead relies on RADIUS accounting functions to track concurrent endpoints on the network and generate alarms when endpoint counts exceed the licensed amounts"
My question is, that aside from a scenario where TAC is engaged and they see the license count exceeded, what is the operational and functional impact of exceeding the license count. I know that ISE continues to process autthentications, because the 251st client is not refused access.
I've read the Order Guide and the User Guide and the Hardware Guide, and no actual impact is mentioned.
thanks in advance,
Andrew

I had a similar question. I asked how does ISE calculate users. In the wlc I would see 10k radius clients but ISE would show half that number. This is what I was told:
Unfortunately there is no documentation on it. The active endpoints are calculated from the active sessions seen on the primary monitoring node session database, meaning active client sessions seen by PSNs and reported to the primary monitoring node. As to the rules that qualify an endpoint as active, there isn?t really even any internal documentation on that. The effective behavior seen indicates that this is calculated by endpoints who authenticate and continue to re-authenticate/periodically trigger accounting updates from NADs. Hopefully this helps!
Tac case # 627456397
Sent from Cisco Technical Support iPad App

First question - I have Acrobat 9 on my desktop and the license seems to have been messed up. I tried to download and fis but I asked me for a disk. I don't have any idea where the "disk" is. Can I get the license update without that disk?

First question - I have Acrobat 9 on my desktop and the license seems to have been messed up. I tried to download and fis but I asked me for a disk. I don't have any idea where the "disk" is. Can I get the license update without that disk?
Second question - In anticipation of not being able to do that, I bought (at University bookstore) Acrobat XI Pro - do I need to uninstall the 9.0 Pro version before I try to install the XI version?

If you still have your serial number for Acrobat Pro there is a link to the installer here: Download Acrobat products | 9, 8

I suffered a hardware failure on my PC, and have moved to an iMac. I own Adobe creative Suite 4 for Windows. Can I transfer the license to my new iMAC without the huge expense of buying a new license?

I suffered a hardware failure on my Dell desktop PC, and have moved to iMac. I own Adobe creative Suite 4 Design Premium for Windows. Can I transfer the license to my new iMAC without the huge expense of buying a new license or purchasing a month to month option?

you need a cross-grade, but adobe only offers free cross-grades for current releases, Order product | Platform, language swap

How can i check the license file installed on the server CCM 6.1.4

Hi;
i have installed the CCM 6.1.4; and now i want to upgrade to 8.5, but i don't remenber witch type license i have uploaded ( normal or Hospitality).
how can i check the license file installed on this server???
thanks.

Hi Matthew,
I think your idea should work just fine, but you will need to work with;
[email protected]
To put together the proper license file due to this change called the "License MAC"
Customer Impact from New Licensing Procedures
Cisco Unified Communications Manager on VMware on Cisco UCS B-Series Blade Servers uses a different licensing model than Cisco Unified Communications Manager on an MCS server. The MAC address of the NIC card is no longer used to associate the license to the server.
Instead, the license gets associated to a license MAC, which is a 12 digit HEX value created by hashing the following parameters that you configure on the server:
•Time zone
•NTP server 1 (or "none")
•NIC speed (or "auto")
•Hostname
•IP Address (or "dhcp")
•IP Mask (or "dhcp")
•Gateway Address (or "dhcp")
•Primary DNS (or "dhcp")
•SMTP server (or "none")
•Certificate Information (Organization, Unit, Location, State, Country)
This hash of these fields is called the LICENSE MAC
Note : Once there is a change in any of the parameters that creates the License MAC, it will
give you 30 day grace period to generate a new license file for the CM based on new license
MAC.
http://www.cisco.com/en/US/docs/voice_ip_comm/cucm/install/8_0_2/install/cmins802.html#wp584709
Cheers!
Rob

I purchased the license of photoshop & lightroom for 1 year I guess it has been double paid. I would like to cancel the 1 of double payment. Where can i find the license?

I purchased the license of photoshop & lightroom for 1 year I guess it has been double paid. I would like to cancel the 1 of double payment. Where can i find the license?

You are likely going to have to contact Adobe Support directly by chat or phone when they are available.
Manage your membership and payments | Creative Cloud
https://helpx.adobe.com/x-productkb/policy-pricing/membership-subscription-troubleshooting -creative-cloud.html
For the link below click the Still Need Help? option in the blue area at the bottom and choose the chat option...
Creative Cloud support (all Creative Cloud customer service issues)
http://helpx.adobe.com/x-productkb/global/service-ccm.html ( http://adobe.ly/19llvMN )

How can I bring the recordset count inside the same recordset?

I have a query inside a procedure where I'm paging the results.
I dont know how to bring the total results inside the recordset.
How can I bring the recordset count inside the same recordset?
SELECT *
FROM ( select a.*, rownum rnum
     FROM (SELECT
          FROM table
          ORDER BY id DESC) a
     WHERE rownum <= pg*50 )
WHERE rnum > (pg-1)*50

My query is much more comples, so that is why I'm using the other script.
When I included the "COUNT(*) OVER() tot_cnt AS total" it didn't worked:
ORA-00904: "TOT_CNT": invalid identifier
What is the tot_cnt?
SELECT *
FROM (SELECT a.*, rownum rnum
FROM (SELECT
ed_fotos.id AS COD_FOTO,
ed_fotos.arquivo AS NOM_ARQUIVO,
ed_areas.nome AS NOM_REDACAO,
COUNT(*) OVER() tot_cnt AS total
FROM edt.ed_fotos ed_fotos
INNER JOIN edt.ed_volumes ed_volumes ON ed_volumes.id = ed_fotos.volume_id
INNER JOIN edt.ed_caminhos path_alta ON path_alta.id = ed_volumes.caminho1
INNER JOIN edt.ed_caminhos path_baixa ON path_baixa.id = ed_volumes.caminho2
INNER JOIN edt.ed_areas ed_areas ON ed_areas.id = ed_fotos.redacao_id
ORDER BY id DESC) a
WHERE rownum <= 200 )
WHERE rnum >= 100

Computer crashed, had to move programs to new hard drive, now Lightroom wants a serial number to open and I can only find the license key I was given upon purchasing it.

My computer crashed and now when I try to open Lightroom it's asking me for a serial number. I purchased this program off of Amazon and I can only find the License Key # in the e-mails they sent me. How can I retrieve my serial number?

https://www.adobe.com/account.html for serial numbers or subscriptions on your Adobe page

How can I get the shutter count for my Canon 7D Mark II using Windows XP?

How can I get the shutter count for my Canon 7D Mark II using Windows XP? I've been looking lots of places and doing some file uploads, but I can't seem to find anything. I'm wary of downloading software I know nothing about. Any help is greatly appreciated.
Solved!
Go to Solution.

Nevermind, just, sort of answered my own question. Doesn't work on XP, but using a Win 7 'puter I was able to use Shutter Count, which now works w/ the 7D Mark II.

Can we explain the following counter..FCP_SW_CNTR_RX_WT_AVG_B2B_ZERO

Can we explain the following counter..FCP_SW_CNTR_RX_WT_AVG_B2B_ZERO
We see it when looking for dropped packets on the ds-9248-256k9 port blades.

Hi,
FCP_SW_CNTR_RX_WT_AVG_B2B_ZERO is the average amount of times the RX buffer to buffer credits went to 0 on that interface. If you are seeing the counter increasing it could be because of a slow drain device in the fabric.

ASR1001-X, Bandwidth is exceeding the license level.

Dears,
I need to double check with you regarding the below log message:
Apr 22 12:47:38.178 JTZ: %BW_LICENSE-4-THROUGHPUT_MAX_LEVEL: F0: cpp_ha: Average throughput rate exceeded the total licensed bandwidth 20000000000 bps and dropped 35 times, sample period 300 seconds, in last 24 hours.
Does this means that i am having high throughput that exceeds my license 20G or what?
Below you can find the "Show version" and "show license" from the Router:
MN-RT-REP-01#sh license all
License Store: Primary License Storage
StoreIndex: 0   Feature: adventerprise                     Version: 1.0
        License Type: Permanent
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Medium
StoreIndex: 1   Feature: ipsec                             Version: 1.0
        License Type: Permanent
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Medium
License Store: Built-In License Storage
StoreIndex: 0   Feature: adventerprise                     Version: 1.0
        License Type: EvalRightToUse
        License State: Inactive
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 1   Feature: advipservices                     Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 2   Feature: avc                               Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 3   Feature: fwnat_red                         Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 4   Feature: ipsec                             Version: 1.0
        License Type: EvalRightToUse
        License State: Inactive
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 5   Feature: lawful_intr                       Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 6   Feature: lisp                              Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 7   Feature: otv                               Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 8   Feature: sw_redundancy                     Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 9   Feature: throughput_5g                     Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 10 Feature: throughput_10g                    Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
           Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 11 Feature: throughput_20g                    Version: 1.0
        License Type: RightToUse
        License State: Active, In Use
        License Count: Non-Counted
        License Priority: Low
StoreIndex: 12 Feature: vpls                              Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA not accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 4 days
            Period used: 0 minute 0 second
        License Count: Non-Counted
        License Priority: None
StoreIndex: 13 Feature: interface_10g                     Version: 1.0
        License Type: EvalRightToUse
        License State: Active, Not in Use, EULA accepted
            Evaluation total period: 8 weeks 4 days
            Evaluation period left: 8 weeks 3 days
            Period used: 1 minute 5 seconds
        License Count: 0/0 (In-use/Violation)
        License Priority: Low
MN-RT-REP-01# sh ver
Cisco IOS XE Software, Version 03.12.00a.S - Standard Support Release
Cisco IOS Software, ASR1000 Software (X86_64_LINUX_IOSD-UNIVERSALK9-M), Version 15.4(2)S0a, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2014 by Cisco Systems, Inc.
Compiled Tue 13-May-14 18:36 by mcpre
Cisco IOS-XE software, Copyright (c) 2005-2014 by cisco Systems, Inc.
All rights reserved. Certain components of Cisco IOS-XE software are
licensed under the GNU General Public License ("GPL") Version 2.0. The
software code licensed under GPL Version 2.0 is free software that comes
with ABSOLUTELY NO WARRANTY. You can redistribute and/or modify such
GPL code under the terms of GPL Version 2.0. For more details, see the
documentation or "License Notice" file accompanying the IOS-XE software,
or the applicable URL provided on the flyer accompanying the IOS-XE
software.
ROM: IOS-XE ROMMON
MN-RT-REP-01 uptime is 22 weeks, 5 days, 46 minutes
Uptime for this control processor is 22 weeks, 5 days, 47 minutes
System returned to ROM by reload
System restarted at 11:46:58 JTZ Fri Nov 14 2014
System image file is "bootflash:/asr1001x-universalk9.03.12.00a.S.154-2.S0a-std.SPA.b"
Last reload reason: Reload Command
This product contains cryptographic features and is subject to United
States and local country laws governing import, export, transfer and
use. Delivery of Cisco cryptographic products does not imply
third-party authority to import, export, distribute or use encryption.
Importers, exporters, distributors and users are responsible for
compliance with U.S. and local country laws. By using this product you
agree to comply with applicable laws and regulations. If you are unable
to comply with U.S. and local laws, return this product immediately.
A summary of U.S. laws governing Cisco cryptographic products may be found at:
http://www.cisco.com/wwl/export/crypto/tool/stqrg.html
If you require further assistance please contact us by sending email to
[email protected].
License Level: adventerprise
License Type: Permanent
Next reload license Level: adventerprise
cisco ASR1001-X (1NG) processor with 3765392K/6147K bytes of memory.
Processor board ID FXS1834Q2EE
6 Gigabit Ethernet interfaces
2 Ten Gigabit Ethernet interfaces
32768K bytes of non-volatile configuration memory.
8388608K bytes of physical memory.
6688767K bytes of eUSB flash at bootflash:.
Configuration register is 0x2102
Regards,
Muhannad

Hi Muhannad,
Sounds like it. Looks like you can do:
show platform hardware throughput level
This reads like 20G is the limit as well.
http://www.cisco.com/c/en/us/td/docs/routers/asr1000/install/guide/1001-x/asr1hig/asr1lic.html#pgfId-1060881

How can I get the skip count to work on my iPhone?

I continue to keep looking for the answer to this question however, it's seems that I continue to keep running into a wall. I have several of my smart playlists that rely on monitoring the skip counts. I never had an issue until I upgraded from a touch to an iPhone. What's the deal? This phone can do everything and anything imaginable but it can' keep a skip count. Has anyone figure out how to fix this, or am I going to be waiting like everyone else for apple to fix the issue? Help!!!! This is frustrating.

I Cannot use the meddle button on my p
iPhone

How can i display the error count

Hi I'm using jdev11g
How can i display the count of errors in validation error message pop up instead of displaying the entire list.

Searching the forum would help
Re: How to customize Error?

How can i select the step count of a recursive CTE ?

I want to select the step count of this query (which one is do fiirst and continue + 1) from query below
;WITH EmpCTE( BomID , empid, mgrid,BomMgrId, lvl, Qty , FLG)
AS
SELECT BomID , empid , mgrid, 0 as BomMgrId , 0, Qty , FLG
FROM Employees
WHERE empid = 1
UNION ALL
SELECT E.BomID , E.empid, E.MgrId, M.BomID as BomMgrId , M.lvl+1 , E.Qty , E.FLG
FROM Employees AS E
JOIN EmpCTE AS M
ON E.mgrid = M.empid
SELECT BomID , empid, BomMgrId as mgrid , FLG , qty , lvl FROM EmpCTE WHERE FLG is null

Please post DDL, so that people do not have to guess what the keys, constraints, Declarative Referential Integrity, data types, etc. in your schema are. Learn how to follow ISO-11179 data element naming conventions and formatting rules (you have no idea).
Temporal data should use ISO-8601 formats. Code should be in Standard SQL as much as possible and not local dialect.
This is minimal polite behavior on SQL forums.
What you did post is a common design error made by people who do not understand how sets work. This is not RDBMS! It is a sequential file system, kludged in SQL using the recursive CTE that hides the cursors and loops.
>> I want to select the step count of this query (which one is do first and continue + 1) from query below <<
Step? A set has no concept of ordering. Your question is like asking about the gills on a dog in a veterinarian forum.
An SQL programer would have a table (set) with the name Personnel. This is a higher level abstraction. But you have Employees, a sequential file or list.
Managers and subordinates are not attributes as you show them. There is a relationship among employees. You have a non-normalized model that mixes relationship and entities together in violation of basic data modeling.
We also do not use flags in SQL; that was assembly language.
Please follow Netiquette and post the specs and DDL , so we can replace it with a nested sets mode.
--CELKO-- Books in Celko Series for Morgan-Kaufmann Publishing: Analytics and OLAP in SQL / Data and Databases: Concepts in Practice Data / Measurements and Standards in SQL SQL for Smarties / SQL Programming Style / SQL Puzzles and Answers / Thinking
in Sets / Trees and Hierarchies in SQL

Where can I find the license for Adobe Photoshop and Premiere Elements 6?

Does anyone have any ideas of how many computers I can put this software onto??
Thanks!

Contractually, the license allows you to install it on just two computers, as specified in paragraph 2.4. PSE 6 doesn't enforce that provision programmatically as many Adobe products do (including PSE 8), so you could install it on 200 computers, if you wanted to violate the terms of the license agreement.

Can I exceed the license count on a 5508 series WLAN controller?

Similar Messages

Maybe you are looking for