Can I extend a network with AE, then plug into it?

i have checked but can't seem to answer this exact question:
i have a time capsule and my G5 tower is plugged in using ethernet (no wifi card). I also have a MBP. i am moving my G5 one floor down where there is no ethernet plug, but the wife reaches.
can i extend the network with an AE and then PLUG the G5 into the AE? or will i need a wifi card?
thanks in advance
keith

You would use AirPort Utility to first check the settings on the Time Capsule
AirPort Utility - Manual Setup
Click the Wireless tab below the row of icons
Make sure there is a check mark next to "Allow this network to be extended". Otherwise, things won't work.
Note the exact Security setting you are using for use with the AirPort Express
Use AirPort Utility the same way for the Express
Click the Base Station tab to name the device, assign password, adjust Time, etc
Click the Wireless tab:
Wireless Mode = Extend a wireless network
Wireless Network Name = Same name as the Time Capsule network
Check mark next to Allow Wireless Clients
Wireless Security = Same setting as the Time Capsule
Wireless Password = Same password as the Time Capsule
Confirm Password
Update to save changes. You should have green light in 30-40 seconds and the ethernet port will be active.

Similar Messages

Can I extend a network with an AirPort Extreme Base Station Rather than with an Express?

Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?

pcbjr wrote:
Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?
Hiya.
You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

How do I extend a network with an AirPort Extreme from an Arris TG862?

I'm using Comcast as my ISP, and after some issues with a previous Motorola modem, they supplied me with an Arris TG862 Router/Modem combo tower. I have two AirPort Extremes, one of which was previously connected to the old Motorola modem to send wireless into the house, but it only reached halfway, so I had the other AirPort Extreme in the middle of the house to "catch" the signal and then broadcast it out to the rest of the house. This worked fine for a while.
But with the new TG862, it doesn't seem to be an option. From what I've read, if I have the TG862 in one room (connected to the cable), AirPort Extreme #1 in the middle of the house, trying to join the existing network (or extend it?), and AirPort Extreme #2 in the far end of the house (to extend from AirPort #1), it won't work. Apple's "extension" technology isn't compatible with all other modems or routers, and even if it was, I'd have to somehow configure the TG862 to "allow to be extended."
So my question is, IF there is a desktop utilizing the TG862 as a direct connection (because it has no built-in Wi-Fi), is it possible to put the TG862 into bridge mode, connect one of the AirPort Extremes and have it act as the router so I can use AirPort Extreme #2 to extend that network out to the rest of the house? I want to ensure the desktop still has a connection, but there's Wi-Fi that actually goes out through the whole house.
The connected-to-the-cable-desktop is a PC; we have multiple iPhones, iPads, and anywhere from 1 Mac laptop to 1 iMac in the house at any given time.

pcbjr wrote:
Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?
Hiya.
You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

I used Airport Base station and I was able to extend my network using airport express and connect my printers. Now I am using Extreme and I can't extend the network (Express) or the printers nothing shows up. I am using utility 6.3 and Mt Lion What is

I had an Aiport Base Station and extended using Airport Express, where I also connected my printers (network). Now using Airport Extreme off Mt Lion 10.8.4 and Utility 6.3.
I can't extend the network (express) or connect my printers (USB) nor will it find my one wifi printer.
What's up?

For now, leave the AirPort Express powered off.
Power off the entire network....all devices.....in any order that you want
Wait a few minutes
Power up the modem first, and let it run 2-3 minutes by itself
Power up the AirPort Extreme next, and let it run a full minute
Keep powering up devices one at a time about a minute apart until everything is powered up (leave the Express off for now)
Open AirPort Utility and check to see if the AirPort Extreme is visible.
If it's not, click the AirPort Utility menu at the upper left of the screen, then click About AirPort Utility. Post back with the version number of AirPort Utility that you see there....which should be AirPort Utility 5.6.1.
Post back on your progress.

How do i use my time capsule and extend the network with airport express

I have a new iMac and Time Capsule, how do i extend the network with airport express. My time capsule does have a guest net work, and logins and passwords? I am no computer person. So for me it would have to be spelled out.

Use the search as this has been done to death ..
Bob Timmons is the expert on this.. look at his answers here.
https://discussions.apple.com/thread/4274187?start=0&tstart=0
https://discussions.apple.com/message/21856077#21856077
This has been automated in the v6 utility. I am used to doing it manually in v5 utility which is also fairly easy.
Apple doco is also good to read.
http://support.apple.com/kb/HT4145
http://support.apple.com/kb/HT4259
Note.
You cannot extend the guest network unless everything is up to date 7.6.3 firmware. And that is only with the TC as the main router in the network.
All apple routers can be configured as the main wireless or as the extend wireless.. so don't worry if a post uses express or extreme or TC.. they are for wireless, the same thing.

Using time capsule to extend a network with security

I have a time capsule and my roommate and I use the same wireless network. I want to add my time capsule to the network we both share but want to be sure only I will be able to access data on my time capsule i.e. external hard drive, back ups etc. Is this possible?

The Time Capsule can only extend a network wirelessly if it connects to the wireless signal from another Apple router.
So, the first question here would be whether or not the existing wireless network there is being provided by another Apple router.
If yes, what model of router would this be?
If no, then the Time Capsule will need to connect to the existing wireless router using a permanent, wired Ethernet cable connection.
If you do it this way, you have the option to have the Time Capsule produce a separate wireless network, or you can turn off the wireless on the Time Capsule and use it only as a wired hard drive.
No matter how the Time Capsule is set up, you would want to set up a separate Disk Password for the Time Capsule, so only those users who had the password could access the Time Capsule hard drive.

Trying to extend my network with express but it times out

Trying to extend my network with an airport express, but everytime I follow the instructions it prompts me to "switch" networks and then it times out.

What is the make & model of the wireless router that you are trying to extend with the 802.11n AirPort Express Base Station (AXn)?

HT4972 can't connect to network with linksys e2500

Can't connect to network with linksys E2500. Can anyone help me?

Look at iOS Troubleshooting Wi-Fi networks and connections http://support.apple.com/kb/TS1398
iPad: Issues connecting to Wi-Fi networks http://support.apple.com/kb/ts3304
iOS: Recommended settings for Wi-Fi routers and access points http://support.apple.com/kb/HT4199
Additional things to try.
Try this first. Turn Off your iPad. Then turn Off (disconnect power cord) the wireless router & then back On. Now boot your iPad. Hopefully it will see the WiFi.
Go to Settings>Wi-Fi and turn Off. Then while at Settings>Wi-Fi, turn back On and chose a Network.
Change the channel on your wireless router. Instructions at http://macintoshhowto.com/advanced/how-to-get-a-good-range-on-your-wireless-netw ork.html
Another thing to try - Go into your router security settings and change from WEP to WPA with AES.
How to Quickly Fix iPad 3 Wi-Fi Reception Problems
http://osxdaily.com/2012/03/21/fix-new-ipad-3-wi-fi-reception-problems/
If none of the above suggestions work, look at this link.
iPad Wi-Fi Problems: Comprehensive List of Fixes
http://appletoolbox.com/2010/04/ipad-wi-fi-problems-comprehensive-list-of-fixes/
Fix iPad Wifi Connection and Signal Issues http://www.youtube.com/watch?v=uwWtIG5jUxE
Unable to Connect After iOS Update - saw this solution on another post.
https://discussions.apple.com/thread/4010130?tstart=60
Note - When troubleshooting wifi connection problems, don't hold your iPad by hand. There have been a few reports that holding the iPad by hand, seems to attenuate the wifi signal.
~~~~~~~~~~~~~~~
If any of the above solutions work, please post back what solved your problem. It will help others with the same problem.
 Cheers, Tom

Can I extend my network by connecting one of my airport express devices to my airport extreme via an ethernet cable? I have CAT5 cable throughout my house but have a wireless network w/ 3 airport expresses

Can I extend my wireless network by connecting one of my airport express devices to my airport extreme via an ethernet cable? I have a wireless network with 3 airport expresses and 1 airport extreme functioning as the base station. I have CAT5 throughout my house.

Welcome to the discussions, mib88!
Can I extend the network a second time with another Airport Express...
The short answer would be no. If you want more details, please continue to the next paragraph.
Apple's "extend a wireless network" works just like the hub and spokes of a wheel. Your main hub is either the Time Capsule or the AirPort Extreme and the AirPort Express is at the end of a spoke. You can add more devices at the ends of other spokes, but these devices will communicate directly to the hub, not to another device at the end of a spoke.
Apple does offer an option which is is known as a "static WDS", which can consist of a "main", "relay" and "remote" device. The problem here is that this type of setup has two huge drawbacks:
1) All of your faster "n" devices will drop down to much slower "g" speeds
2) The bandwidth or speed capability on the network will drop down to only 25% of the original bandwidth with a "main", "relay" and "remote" on the network.
Don't think you want this on your network. Your best option is to connect the new AirPort Express to the "hub" using an ethernet connection. If you can't run the ethernet cable, take a look at a pair of ethernet powerline adapters to accomplish the same task by sending the ethernet signal over the AC powerline in your home.

Airport express can't extend wireless network

Airport express(A1264) can't extend wireless network. It seems that Airport express can't find my home Wi-Fi network. Amber light is blinking, and AirPort Utility of MacBook also can't find Airport express.
If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
It was successful only once, but all failed after that.
Is there solution for this problem?
[My system]
Time capsule 4th generation
Airport express 1st generation (A1264)
[Settings]
Time capsule (ethernet connected)
- Create a wireless network
- 802.11a/n - 802.11b/g/n (Automatic)
- 2.4GHz / 5GHz Channel (Autmatic)
- WPA2 Personal
Airport express
- Extend a wireless network
- WPA2 Personal
- 2.4GHz Wi-Fi network name and Password is set up

If AE is connected with TC via LAN cable, amber light is blinking with message "Wireless Network" (This Airport base station is set up to join a specific wireless network that can't be found...)
Sorry, I misunderstood what you wanted to do.
Since you did tell us that you had the Express connected with an Ethernet cable, I assumed that was how you wanted to configure the Express.
But I want to extend a wireless network (not using ethernet)
Because Airport Express and Time Capsule cannot be connect via ethernet cable.
Follow the same setup as above....and do not connect an Ethernet cable.
Keep the Express near the Time Capsule for the setup. Once you have a green light, move the Express to a point that is about half way between the Time Capsule and area that needs more wireless coverage.
If you reset the Express several times and try the setup several times without success, I think you have to suspect a defective Express.

Extending wireless network with an aiport express

I have a netgear wireless router set up in my house on the second floor, but my room being located on the first floor i get a poor signal so i bought an airport express to extend my network. i tried going through the aiport exress setup assistant but that wouldnt work, so i ended up hooking it to my netgear router on the second floor to set it up in airport admin utility and then brought it back down to the first floor. my itunes worked with the speakers for about.. ten seconds then stopped. and my signal is just as weak as before.. any suggestions?

Unfortunately, it is simply not possible to use an Airport Express to wirelessly "extend" the wireless range of any model of Netgear wireless router. Netgear's wireless routers do not support Apple's implementation of a wireless distribution system (WDS), which is a necessary requirement for setting up an extended wireless network with the Airport Express. And no - it doesn't work the other way around either (Airport Express as base station, Netgear wireless router to "extend").
It sounds like you did successfully configure your Airport Express to "join" your existing wireless network - which will allow you to print and stream iTunes to the Airport Express. The problems you are having with Airtunes "hanging" on your Mac are almost certainly due to the poor wireless signal quality problem that you are already aware of.

How do i extend my network with a airport express

How do I extend my network with mt airport express

Hi Tesserax, I'd like to join this discussion. It seems Jasonbeyer didn't reply, but I have a question related to his.
I'd like to extend the wireless signal from my Cisco Model DPC/EPC2202 VoIP Cable Modem (802.11n) to the living room where, at the moment, it is non-existent. I assume there's inteference or the signal cannot reach through the concrete walls and rooms leading up from my bedroom to the living room.
My question is:
I'm thinking of extending my wi-fi signal by using the Airport Express and simultaneously using it to connect to my hi-fi to play iTunes from my bedroom's iMac.
Something's telling me it's not going to be that easy. I'm using an iMac (7,1) if that's any help or clue.
What are the things I should take note of and will Airport Express be compatible with my modem? Would I have to get TWO Aiport Express to bridge the signal to my living room?
Thank you everyone for your time. Cheers!
Kane

Can't see wireless network with Windows Vista

I have the Airport Extreme N and two PCs, one with W XP and one with W Vista. Everything works fine with the XP PC. On the Vista PC, I can connect to the network with LAN, but I can’t see the wireless network.
The W Vista PC can identify other networks around the block, so the Broadcom 802.11g network adapter seems to work fine. The wireless runs on channel 13, which is OK for the XP PC. I have installed the latest update for the Airport Extreme.
Any suggestions to what I can do to get the W Vista PC working on wireless?
Best, Kasper

Hi,
I also have the same problem.
My belkin wirelss router is set to channel 13, therefore my macbook cannot see this network when it search's, for the above reasons.
However unlike the situation above I am unable to change from channel 13 as we have discovered in the past that this is the only channel that is not in use by other networks around our area. The rest gave us interferance troubles.
I have a number of windows laptops in the house and there is a setting that you can change so the laptop will search for channel 13. I was wondering if anyone is aware of a setting on the macbook that will make the airport card search for 1 - 13 not just channels 1 - 10 as it is now.
I thought I would add this question to this topic as it is very similar. I hope I was correct in doing so.
Thanks,
Josh
Macbook Mac OS X (10.4.8)

Hi there! We just got an ipod touch 8G. We have wireless internet, but can't join the network with the ipod touch! Very frustrating and we have tried all of the troubleshooting suggestions on the support site. Help! The router is a linksys WRT120N.

Hi everyone! WE just got an ipod touch 8G. We do have wireless internet, but can't join the network with the ipod touch. Message comes up.."unable to join the network".....very frustrating! We have tried all trouble-shooting suggestions on the site, but nothing is working. Anyone out there got any ideas for us?? The router is a Linksys WRT120N.
Thanks for any help any one can give!!!

Does the iPod connect to other neworks?
Do other devices connect to the network?
What encryption are you using?
How you tried changing the type of encruption? Changing to no encryption?

Extending a network with Airport Express 802.11n-2.4 or 5.0GHz?

I've just ordered an AirPort Express N to extend the network of my AirPort Extreme (Gigabit) and run AirTunes. It'll be connected to the router by Ethernet.
My question is this: can I run the Express at 2.4GHz (802.11b/g/n) while I run the Extreme at 5.0GHz (802.11n only), even though they're on the same network? I've got a couple of 802.11g machines (my old iBook and my iPhone, for two), so I need to keep backward-compatibility, but I'd love for the 802.11n machines (my iMac, and my wife's Mac Book) to connect at the higher speed. Can you extend a network on different frequencies?
Message was edited by: David Kudler

My question is this: can I run the Express at 2.4GHz (802.11b/g/n) while I run the Extreme at 5.0GHz (802.11n only), even though they're on the same network?
No, not while they are in a WDS. If you want to operate wireless networks in both radio bands, you would need to configure the base stations in a "dual band" network.
Setting up a "dual band" network is described in the Designing AirPort Networks document, starting on page 48.

Can I extend a network with AE, then plug into it?

Similar Messages

Maybe you are looking for