Can I extend a network with an AirPort Extreme Base Station Rather than with an Express?

Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?

pcbjr wrote:
Topic title pretty well sums up the question.
I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
So, can the Extreme act as an "extender" only, in lieu of using an Express?
Hiya.
You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

Similar Messages

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

How do I set up a wireless network with an AirPort Extreme base station and two airport extreme but between apple devices either by ethernet

This Apple support document provides good general information on configuring different types of neworks using multiple AirPort routers.
http://support.apple.com/kb/HT4145
In particular, you would want to focus on the information regarding a "Roaming Network"

How many devices can I use with an AirPort Extreme Base Station?

How many devices can I use with an Airport Extreme Base Station? Devices included a mac, iphone, ipad and pc laptops.

The AirPort Extreme will support up to 50 wireless devices and 200 wired Ethernet devices. I would imagine that this would probably be adequate for most homes.

How can I extend a wireless network with my AirPort Extreme Base Station?

Today I purchased a brand new, dual-band base station to replace my Belkin N router, as I have had a handful of firewall, coverage, and other networking problems in my house lately. First off, I really like this router and it was very easy to setup. My MacBook Pro could use both bands and established a 300 Mbit/s link very quickly. After tweaking various settings to my liking, I was also able to maximize the connections on many of my non-Apple machines and devices. I noticed that the range of its network was better than my Belkin's, but unfortunately, it failed to completely saturate the area sufficiently. Since the Belkin still works well enough, I was hoping I could bridge them together one way or the other.
The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct? I would like to place them at opposite ends of my home so I can get strong WiFi signals everywhere inside. However, when I try to get the base station to connect to my preexisting WiFi connection, it tells me that I can't extend the network and fails to join.
So is this possible? And if it is, how would I go about setting it up? I know it would probably be easier if I had a simple range booster such as an AirPort Express, but I didn't buy one while I was at Fry's since I hoped I could make use of the older Belkin. This is its product page, if needed. Thanks for any suggestions.
-MacUser

The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct?
Sorry, but no. The AirPort Extreme Base Station cannot "join" a network like the AirPort Express or Time Capsule, but you wouldn't want to do this anyway because in this configuration these devices will only perform as wireless clients ... not routers.
Instead, the AirPort Extreme can either be extended or can extend another 802.11g or 802.11n AirPort ... or a very very few non-AirPort devices.
One option for your Belkin would be to connect it to the AirPort Extreme by Ethernet but this may not meet your requirements or be a desirable situation. Otherwise, you would need to get another AirPort to extend your current one.

What needs to be done to avoid WIFI drop-offs with Apple AirPort Extreme Base station with Extended Wifi

Hi there,
can anybody please advise me what needs to be done to avoid WIFI drop-offs every half an hour or 1 hours.
I use voip phoe calls a lot using my WIFI, However my AirPort WIFI connection drops-off while I am in the middle of WIFI VOIP calls. This is causing significant disturbance in my family.
Please assist.
In details, I have extended my WIFI range using 2 Apple Airport Extreme Base Station.
Main Base is - A1408 9 (5th Gen), and I have extended my WIFI in my L shape house by connecting another Apple AiPort A1354 ( 4th Gen) with AA1408.
Note1:
> when I am close to A1408 my iPhone4 connected with A1408 automatically
> When I am close ot A1354 , my iPhone4 connected with A1354 automatically.
Note2: these drop-offs never occurred when I had only 1 Apple AirPort Extreme Base station WIFI
I think, this Auto switching causing the slight drop outs in my Wifi when I am on the VOIP call.
Do you think that something is going wrong with my Apple AirPort Wifi extended?
Much appreciated

To help eliminate drop-offs you need to ensure that your extended network is operating at its peak bandwidth performance. Base station placement is critical in an extended network. Please check out the following AirPort User Tip for details.

Power Mac G3 Pismo with Airport wireless card in Mac OS X 10.4 won't connect to wireless network with newest Airport Extreme Base Station set at WPA Personal/WPA 2 Personal encryption.

My Power Book G3 Pismo with an Airport wireless card running Mac OS X 10.4.11 will not connect to my new Airport
Extreme Base Station using WPA Personal/WPA 2 Person encryption. The Airport firmware is version 9.52. From
posts I've read online at different places indicates the Airport card should support the WPA encryption. Perhaps the problem
is the Base Station is using a combination setting and the fault is in the base station?
Thanks for any suggestions

Perhaps an inexpensive usb wireless adapter would work as well?
This is probably the simplest way to get the G3 connected to the wireless network.
I'll have to read up on getting an express and using it as a wireless bridge as I am unfamiliar with the concept.
The new AirPort Extreme is broadcasting a wireless signal.
A new AirPort Express could be located close to the G3. The Express will pick up the wireless signal from the AirPort Extreme, then provide an Ethernet connection to the G3 though a short Ethernet cable.
This can work very well......IF.....you keep the G3 at a fixed location, since it will always be connected to the AriPort Express using an Ethernet cable.
I do have an old Linksys Wireless G router. I wonder if that would work?
In theory, yes. But it would have to use much older WEP "security", which is easily cracked in minutes using free tools available on the Internet. So, anyone who really wanted to get on the network could do so. It's an option, but not a very good one.

If I set up separate 2.4 and 5GHz networks on my Airport Extreme base station, is it possible to extend just the 5HGz network?

If I set up separate 2.4 and 5GHz networks on my new Airport Extreme base station, is it possible to extend just the 5HGz network with another AirPorrt Extreme that has duel, but not simultanous, frequencies?

Yes, configure the "extending" AirPort Extreme to connect to the 5 GHz network name when you set it up.
Temporarily, locate the extending AirPort Extreme close to the main Extreme for the setup, then move it to the remote location.
But, be advised that it is not easy to extend 5 GHz using wireless. You will almost need to have line-of-sight between the two AirPorts for this to work.

Mac Book pro can't connect to Internet through Apple airport extreme base station

I had problems connecting to the internet in the past with my macbook pro. One day it suddenly started working again but then I bought a second apple TV I lost connectivity. I have tried changing the IP address manually and while it shows me connected to the wifi I am still with out internet. When I hooked up the new Apple TV that I bought it booted my computer from it's ip address. The apple TV though wouldn't work and now nor would my computer. I ended up setting the Apple TV's ip address manually and now it works fine. My computer on the other hand does not no matter if I set it manually or not. Even if I plug in the ethernet cable from the base station it doesn't work. It show that it has a self assigned IP address. After I set it manually it shows that I am connected both via wifi and the ethernet cable but I can't connect to the internet. If I plug the modem directly into the computer bypassing the base station I get internet and it is using the IP address that worked originally.
It has something to do with the connection from the base station to my computer but this is odd considering every other device I have: iPhone 4, apple tv, apple tv, apple mini with retina display all work perfectly via wifi (newest apple tv had to be set manually as I stated above but now works fine). When I check the ip of the base station itself it seems to be different from the ip of the computer when the computer was connected directly to the router. I don't understand why my computer now can't connect to the internet via the base station whether it be wifi or by ethernet. Can you please help me trouble shoot this?
I have an AirPort Extreme base station which allows up to 50 users and a 30 meg connection speed.
I have a MacBook Pro (17-inch Early 2009), OS X Mavericks (10.9.2)

It has something to do with the connection from the base station to my computer
I don't think so..
I just posted a reply which totally vanished.. strange strange website now.
Please post some screenshots of your AE setup from the airport utility.. I want to see the summary page, then the network and internet tab.
Please tell us what modem you use.. is it a router??
If you have satellite or 3G wimax etc service they often are limited to 5 IP addresses... the AE takes one and then 4 more devices can join .. no more.
You need to also give us the screenshot of the IP you are getting in a computer that works.
EDIT
Sorry this is half double post.. the previous page refused to display.. now it has returned..

Define static IP for both LAN and W-LAN devices with an Airport Extreme Base Station

Hey guys,
I have a lot of different devices connected to my Airport Extreme Base Station (5th Gen) either wirelessly or via ethernet cable. Since I control some of them via VNC and currently have to find the corresponding IP-addresses through trial-and-error, I'd like to define static IP-addresses for the computers in question. My network consists of a cable modem connected to a TP-Link WR1043ND router in the basement, from which an ethernet cable leads to the WAN-port of the aforementioned Airport Extreme Base Station on the 2nd floor. Two of the devices I want to remote-access are wired to a D-Link DES-1005D switch, which in turn is connected to the 1st ethernet port of the Airport Base Station. The remaining 3 remote clients are connected over 802.11n. All computers run Windows.
My problem now is that even though I was able to define static IP-addresses employing the "DHCP only" router mode, this didn't seem to work for the two computers connected via ethernet. Not only did I lose any internet connectivity with those, I even lost the ability to remote-connect to them using the VNC-viewer.
The question now is: how do I specify static IP-addresses for my ethernet devices correctly?
I hope you can help me.

My network consists of a cable modem connected to a TP-Link WR1043ND router in the basement, from which an ethernet cable leads to the WAN-port of the aforementioned Airport Extreme Base Station on the 2nd floor.
If you read the information in the other post, my answer would be the same here.
The Router Mode of DHCP Only is rarely used, and would only really be appropriate if your ISP was providing you with a fixed bank of multiple fixed or static IP addresses to use. This does not appear to be the case in your post.
If this were the case, the first IP address would be used as a Static IP address for your connection, and other devices on your network would receive the other fixed IP addresses.
99%+ of the time, you would use the Router Mode setting of DHCP and NAT on a network when you want the AirPort to perform as the main router for the network.
But......your post also indicates that you have another router upstream on your network from the AirPort Extreme. You would not want to run two routers in series on a network. That explains the problems that you are having.
The AirPort Extreme needs to be configured in Bridge Mode. It cannot be the "main" router on your network when you already have another router on the network. That is a fundamental networking rule.

Ip8500 does not print with XP & Airport Extreme Base station (OK with Macs)

My canon ip8500 is connected to an Airport Extreme Base station. I can print from either Mac (a G4 and a new iMac 24") but no luck with either XP laptops (accessing the internet is no problem). I've installed both PC's with Bonjour but after a minute or so I get a failed to print message. Any suggestions?

They are simply obsolete. You cannot update their firmware to be compatible with new products. Buy something to replace them such as a couple of new Airport Expresses.

Setting Up Comcast to Work with the AirPort Extreme Base Station

I just set up Comcast high-speed internet through the cable modem and ethernet connection and it works fine. What I need is a step by step instruction on how to set up the connection through my AEBS. I've tried to configure using the Admin Utility, the AirPort Set-Up Assistant, the Network panel---all with no success. I'm not sure what to enter in the boxes or what to check. I've read the "Designing AirPort Networks" PDF and it wasn't much help.
The AirPort Network was working fine with the dial-up connection I had before.

Voila! NOT!!!
I'm having the same problem trying to set up a friend's "new" Macs, and I cannot get them connected to the internet. I've also followed the same steps. I tried the resetting trick (unpluging, waiting, repluging the modem first, then the Airport Extreme Base Station.)
The DSL ISP is SBCGlobal. Their dsl modem is SpeedStream 5100. The AirportEBS is the about 4 year old white base station with the phone jack, and a WAN and a LAN ethernet ports. I'm trying to connect two iBooks and a MacMini.
Everything did fine for the past year with the modem in "regular" mode and only ONE Mac connected. When the new Macs were recently acquired, SBC techs said that the modem needed to be put into PPPoE mode so that multiple Macs could be connected at the same time. This was done. [The techs said in regular moden the modem does the authentication; in PPPoE mode the modem acts as a bridge and the AirportEBS is the router and provides the authentication. I am assuming the techs are coreect, but I don't know for sure.] The CAT5 ethernet cable from the modem goes into the WAN port on the AEBS. The computers all see the local wireless network set up by the AEBS.
However, when any of the Macs try to connect to the internet, the error message returns "No PPPoE server available." Resetting the modem and base station has not cured this. [n.b. Bypassing the AEBS completely by connecting the CAT5 cable from the modem directly to the Mac will provide internet connection.] Any other ideas? Sounds like both of us are having the same sort of problem.

Can't connect to a VPN through Airport Extreme Base Station

I'm unable to connect through my Airport Extreme Base Station to my office via VPN. Is there something needed to be set up specially?
I'm using a notebook with WindowXP which connects to internet just fine.

Here is info:
Airport Utility finds an Airport Extreme with 802.11n(fast ethernet)
Base Station Name: Home
IP Address: 10.0.1.1
Airport ID: 00:19:E3:FA:A8:32
This is not the IP address of the modem. Even though light is green on Base station the ATV doesn't make the wireless connection.

My airport express is not connecting with my airport extreme base station. They are probably six years old. My IP address on my express shows 0.0.0.0

My Airport extreme and my airport express are not connecting together. I get an error message saying that my airport express software is not compatible with my Airport extreme and I have use them together for the past five or six years. It says I may need to change my IP address on my computer or something like that but I don't know what to do. the IP address on my express shows 0.0.0.0. Should everything be on the same IP address? Any help would be greatly appreciated. Thank you

Please refer to the information already posted above:
If you see A1084 or A1088 there, your older Express is not supported by the newer version of AirPort Utility that you have.
If you have another Mac running Leopard or Snow Leopard, or a PC, then you could use that computer to administer the older Express and it will work on the network along with the AirPort Extreme.
If the Mac running Leopard or Snow Leopard or PC does not "see" the A1084 Express, you will need to "hard reset" the Express by holding in the reset button for 10 seconds and waiting a full minute for the Express to restart. Then, reconfigure the Express again.

Trouble extending a wifi network with 2nd Airport Extreme base station.

I have added a second Airport Extreme in order to extend a network. I connected it to the network via an ethernet cable into one of the three ethernet ports. I have configured it using these instructions (http://systemsboy.com/2009/02/extending-an-airport-network.html). I get green lights for both units.
My network works until I update the second unit. As soon as I update the second unit, my entire internet connection goes down. Even computers in the office that are connected via ethernet cannot access the internet. As soon as I unplug the second base station, the internet connection is "live" again. I don't know how to proceed. I think my brain is fried. Any advice would be helpful.
Thanks,
Rich

Based on the information in your post, the article that you referenced will not provide the correct configuration that you need for your network. In summary, the information in the article is for extending wireless network using wireless only. You are connecting your two routers together using ethernet, correct?
To confirm, your post indicates that +I have added a second Airport Extreme in order to extend a network. I connected it to the network via an ethernet cable into one of the three ethernet ports+
If this is correct, the Wireless Mode for your "main" router should be set to "Create a wireless network".
For the second AirPort Extreme, you will use exactly the same setting, "Create a wireless network". The network name, security and password should match the settings of your main network exactly. This is probably confusing to you, but these are the correct settings when you have the second AirPort Extreme connected to the first using an ethernet cable.
It is critical that the second AirPort Extreme be configured as a "bridge" in order to function correctly on your network. When you are in AirPort Utility - Manual Setup, click the Internet icon at the top of the setup page. Look for the Connection Sharing setting at the bottom of the page. This must be set to "Off (Bridge Mode)". The configuration to "bridge" should be the last step before your click the Update button at the lower right of your screen.
Post back if you need more information or details.

Extending a wireless signal with an Airport Extreme Base Station, and an Airport Express as the "repeater".

I understand that I can extend Airport Extreme wirless "reach" with an Airport Express, but how? I've read through the posts and they say to "connect" the Airport Express. What does that mean, to an outlet, to an ethernet cable, what?

I understand that I can extend Airport Extreme wirless "reach" with an Airport Express, but how?
Enable the option on the AirPort Extreme to "Allow this network to be extended"
Then configure the AirPort Express to "Extend a wireless network"
If you do it this way, the AirPort Express connects to the AirPort Extreme using wireless only.
If you have the ability to run an Ethernet cable from the AirPort Extreme to the AirPort Express and leave it connected permanently, that will provide better performance than the "wireless only" type of connection.

Can I extend a network with an AirPort Extreme Base Station Rather than with an Express?

Similar Messages

Maybe you are looking for