Can I extend my wireless network with my old Airport?

Can I extend my wireless network with my old Airport? I have the airport extreme 802.11n & my old Airport (translucent white) base station. Can I mix the two to expand my range?

No problem; ask as many questions as you need to.
How do I reconfigure the Snow as a bridge to allow the AEBSn to continue to provide both NAT & DHCP services for the entire network?
I don't have a Snow to verify this, but it should be similar to the later base stations when using the AirPort Admin Utility.
To set up the Snow base station as a bridge, either connect to the Snow's wireless network or temporarily connect your computer directly (using an Ethernet cable) to the Ethernet port of the Snow, and then, using the AirPort Admin Utility (located in the \Applications\Utilities folder), make these settings:
Network tab
o Distribute IP addresses (unchecked)
o Apply the new setting.

Similar Messages

  • Can I extend my wireless network with a WIRED Airport Express?

    So I've seen many, many threads (both here & elswhere on the web) that talk about extending a network wirelessly, but that's not my exact goal.
    I have a Linksys WRT54G and an older (non-N) Airport Express. My intention is this: come out of the cable modem and into the WRT54G's LAN port. (Typical.) Then I have wall jack-plates where ethernet runs are extended to various rooms in my home. The WRT54G is on one end of the house and at the far end the wireless signal is basically useless.
    I would like to come out of one of the WRT54G ports into the wall jack and then hard-wire into the Airport Express (at the far end of the house) for the sake of increasing the wireless signal there. I know that there are WDS issues with the Airport Express and NON-Apple networking gear. However, does hard-wiring the AE circumvent this?
    How should I configure the AE, if this is possible at all? As a relay, as a remote? Join the extisting network, etc.

    Interestingly the Linksys WRT-54G is one of the few non-Apple routers that are WDS-compatible with the earlier 802.11g AirPorts. There are a number of posts on the Internet (use the following search terms: Linksys AirPort WDS) where the authors described how they configured theirs to work.
    If; however, you don't want to "experiment," your suggestion to interconnect the two routers by Ethernet should work just fine. In this case, you would want to configure them both for a roaming network.

  • How can I extend my wireless network with the Time Capsule?

    I recently bought a Time Capsule and set it up, backed up all my data, etc. It is currently plugged in to my AT&T Uverse wireless router via a LAN CAT5e cable. I am wondering if it is possible to wirelessly extend my preexisting network with the Time Capsule so I can move it somewhere else in my house where it can still pick up the signal but extend it. And if possible, how so? Or does it ALWAYS have to be wired'connected to my router for the internet to work?
    Thanks in advance.

    I am wondering if it is possible to wirelessly extend my preexisting network with the Time Capsule so I can move it somewhere else in my house where it can still pick up the signal but extend it.
    Sorry but no.  Extending using only wireless would require that the Time Capsule connect to another Apple router that is producing the wireless network.
    Another way of saying the same thing is that you must have two Apple routers to be able to extend the signal wirelessly.

  • How can i extend a wireless network with time capsule

    How can i extend an existing wifi verizon wireless network with time capsule? the router is connected on the bottom floor. want to boost the signal to a home office on the top floor, four flights up. connect time capsule via ethernet cable to iMac on 4th floor? Do I have to start a second wifi network or can I set it to just boost the one I have? thank you

    How can i extend an existing wifi verizon wireless network with time capsule?
    It all depends on what you mean by "extend".
    If you plan to "extend" by connecting the Time Capsule to the Verizon router using a wired Ethernet cable, this can be accomplished.
    If you were hoping to connect the Time Capsule to the Verizon router using wireless only, unfortunately the Time Capsule and Verizon products are not compatible for that purpose.
    Check with Verizon to see if they offer an "extender" or "repeater" that could be located very close to the Time Capsule.
    This would provide both more wireless coverage and also allow you to connect the Time Capsule using an Ethernet cable from the "extender" or "repeater".

  • How can I extend a wireless network with my AirPort Extreme Base Station?

    Today I purchased a brand new, dual-band base station to replace my Belkin N router, as I have had a handful of firewall, coverage, and other networking problems in my house lately. First off, I really like this router and it was very easy to setup. My MacBook Pro could use both bands and established a 300 Mbit/s link very quickly. After tweaking various settings to my liking, I was also able to maximize the connections on many of my non-Apple machines and devices. I noticed that the range of its network was better than my Belkin's, but unfortunately, it failed to completely saturate the area sufficiently. Since the Belkin still works well enough, I was hoping I could bridge them together one way or the other.
    The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct? I would like to place them at opposite ends of my home so I can get strong WiFi signals everywhere inside. However, when I try to get the base station to connect to my preexisting WiFi connection, it tells me that I can't extend the network and fails to join.
    So is this possible? And if it is, how would I go about setting it up? I know it would probably be easier if I had a simple range booster such as an AirPort Express, but I didn't buy one while I was at Fry's since I hoped I could make use of the older Belkin. This is its product page, if needed. Thanks for any suggestions.
    -MacUser

    The Belkin router does not support any bridge mode that I know of, but the AirPort Extreme should be able to join a wireless network and then extend that over WiFi and Ethernet, correct?
    Sorry, but no. The AirPort Extreme Base Station cannot "join" a network like the AirPort Express or Time Capsule, but you wouldn't want to do this anyway because in this configuration these devices will only perform as wireless clients ... not routers.
    Instead, the AirPort Extreme can either be extended or can extend another 802.11g or 802.11n AirPort ... or a very very few non-AirPort devices.
    One option for your Belkin would be to connect it to the AirPort Extreme by Ethernet but this may not meet your requirements or be a desirable situation. Otherwise, you would need to get another AirPort to extend your current one.

  • I have a mid-2010 iMac and just purchased a 2TB TC, can't join existing wireless network with AC standard so attached to iMac via ethernet with TC wifi turned off.  How do i access TC now? not showing up in disk utility or on desktop. working fine with TM

    I have a mid-2010 iMac and just purchased a 2TB TC, I just found out that it can't join existing wireless network with new AC standard so attached to iMac via ethernet with TC's wifi turned off.  How do i access TC now? not showing up in disk utility or on desktop. It is working fine with TM.  My cheeper seagate drives etc kept crashing, so i didnt trust cheeper back up options anymore.  Connected those drives to TM via firewire and could see the drives and access them.
    Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed.  I heard that bridging slows down everything and then there can be port issues with mail etc.  I connect to the internet via airport only and it is pretty fast. Getting over 50mbs downloads and over 30mbs uploads.  Plus everything in my home it connected to my fios router, airport express for music streaming, two apple tvs, vuezone camer system.  I really didn't want to monkey around too much with my system.  But are there other options to connect the new TC.  Can't find info anywhere for this and called apple who gave me the info above.  after hanging up, i see that i cant access my TC and I am wondering if i would have to reset it to turn wifi on again to make changes to the drive, turn off blinking light  or repair it in disk utility if it should become corrupted.
    For other with similar issues i did solve some other problems: when i connected it to my ethernet port on my iMac wifi stopped working.  Found that I had to turn off the ethernet in the system>network screen, but then TM didn't see the TC so i restarted after changes and then it saw it.
    Now a rant.  I can't believe in this wireless age that Apple would make a product that cant join a wireless net work.  The apple rep said i could return it and look for the previous TC that would join an existing wireless network.  Are we going backwards?
    Thanks!
    lennydas

    Ok... it is getting a bit clearer but there are still some questions.
    I connect to the internet via airport only and it is pretty fast.
    I was assuming airport in this statement in your first post meant the TC or the Express.. but I now realise we are still in the mass confusion stage where apple calls everything wireless an airport. So what you mean is the airport internal card of the computer??
    Also, I didn't want to bridge TC with my new fios router that I paid 100 dollars for, to get N speed and also paying 10 dollars more a month for fast speed.  I heard that bridging slows down everything and then there can be port issues with mail etc.
    I think this is mistaken.
    Putting the TC in bridge mode plugged into your FIOS will not slow the network.. nor will it cause mail or port issues.. in bridge the TC is just a fancy WAP and switch plus the network hard drive.
    If the computer is close it will be faster than the FIOS.
    You can run both wireless networks with different names.. so it is clear which is which. But you can also setup roaming so the computers themselves pick which is the best wireless.
    I tried extending the wireless net work and tried joining wireless network, but the TC kept crashing and I had to keep resetting the TC.  the Apple support person said these, extend wireless network and joint wireless network, are no longer a connection option with the new TC because of the new AC protocol.
    Thanks again!
    You cannot extend to a non-apple wireless router.
    You cannot use join a wireless network because when you do the ethernet ports will be cut off.
    But that has not changed.. I don't think Apple support is correct.. there has been no change with the AC model.. it is simply a fact that apple routers do not work in join wireless mode other than as a dumb client. The same applies to AC as to the earlier version.. but I have asked another person to check this.
    Join in the express is the only apple router that still allows an ethernet connection.
    For now you best use of the TC is bridged to the FIOS. Wireless you can sort out between several options.

  • How can I extend my wireless network using Airport Express and an Airport Extreme on BT Infinity?

    I have BT Infinity and I am using the Time Capsule with Airport Extreme as my router. Working well (even on wireless). I want to extend the wireless network with an Airport Express, but I cannot work out the settings necessary in Airport Utility. I am using Mountain Lion 10.8.2 on a Mac Pro. Please help!

    BT,
    I've read several of your posts, thanks for taking the time to share your wealth of knowledge.
    I'm in a situation similar to the one described by 'scoutusmaximus'.  Seeking the flexibility of a standalone router, I finally upgraded my 4-yr old ATT DSL gateway (modem+router) to a Comcast standalone modem + the ASUS RT-AC66U: http://www.asus.com/Networks/Wireless_Routers/RTAC66U/
    Typically, I stick with all things Apple but the ASUS router seemed fairly superior to the current-gen base station (on paper, anyway; time will tell when it comes to performance) so, for once, I jumped ship.  My plan was to extend the ASUS wired/wireless network using my TimeCapsule and 2 Airport Expresses in bridge mode, however, a google search turned up several unhappy customers that claim those devices don't play well with non-Apple routers, especially when it comes to 'extending' a network. 
    Questions:
    1. Can I successfully extend the wired/wireless network created by the ASUS router using the 3 airport devices listed above w/out negatively impacting performance?  I'd rather have 1 wireless network as opposed to creating a new wireless network with the TC and then extending it with the AP Expresses... though I'd consider that option down the line if it came to that.
    2. Will the LAN ports on the TimeCapsule remain functional?
    Btw, my house is wired so, I can reach all 3 devices via ethernet cable coming off of a central, managed switch.  Supposedly, you only lose the LAN ports on the TC if you extend wirelessly.
    Any advice would be appreciated.

  • HT4259 I have a Netgear wndr3400 and I can "join a wireless network" but can not "extend a wireless network" on my Airport express.  Does anyone know why?

    I have a Netgear wndr3400 and I can "join a wireless network" but can not "extend a wireless network" on my Airport express.  Does anyone know why?

    Sorry, but "Extend a wireless network" is a proprietary Apple setting that will only work if you have another Apple router.
    It is not compatible with devices from other manufacturers.

  • Can I use my airport express to extend a wireless network with a non-apple router?

    I have been trying to extend my wireless network in my house.  Right now I have a dsl modem/router provided by Century Link and an older AirPort express (not sure how old but it uses AirPort utility v5.6).  I want to be able to share my printer and use AirTunes.  Currently I have the AirPort plugged into the router and setup to create a new wireless network.  I would like to combine them so I don't have to switch between to print and play music.  I am not really sure where to start or if it even possible.  Any info would be great!

    If you keep the Express connected using Ethernet and configure the Express to "Create a wireless network" using exactly the same wireless network name, exact same wireless security and same wireless password as the Century Link network.....everything will behave as one "big" network, and you will have additional wireless coverage near the Express.
    If you do not need extra wireless coverage, you can turn off the wireless on the Express.
    The Express must be in Bridge Mode.
    Most users know the name of their wireless network and password, so the really tricky part of doing this is that you must know exactly what type of wireless security settings the Century Link router is using....and then match up the same settings on the AirPort Express.
    If the settings do not match up exactly, then you wind up with two separate networks that will each require their own log on.
    If you can check the setting for wireless security on the Century Link router and provide that information to us, we can tell you how to set things up the way that you would like.

  • I have installed Airport Extreme on my iMac, but want to extend the wireless network with Airport Express. Everything is fine until I try to select Extend the wireless network.  I select Extend Wireless network but have no success. Ideas?

    I have installed Airport Extreme on my iMac, but want to extend the wireless to rooms with a weak signal.  The internet connection is fine with the basic setup. As soon as I go into Airport Utility to select Extend Wireless Network and fill in what I believe is proper information, I get an error message that Airport Extreme no longer has an IP address, the internet connection is broken, and under Wireless, that there is a wireless network in existence that can't be found. Rebooting the modem only brings the Airport Extreme back to the starting gate so that the internet is once again available.  I assumed (naively) that with the All Mac All-the-Time context, adding Airport Express would truly be Plug and Play.   I got the plug, but no play.  I asked a Comcast technical specialist about it and he said that I needed to reset the Airport Express settings back to their default, factory status.  I looked that process up online and found out that the way to do that was to hold down the reset button, then plug Airport Express into the socket and wait for the green light to flash four times.  Then wait 45 seconds and the default settings will return.  I did all that, only to find out that after the initial flash of green, green never appeared again.  I got a fast flashing yellow light, followed by the light going off.  Apparently this didn't reset it properly.  So, after hours trying to get this system to work, I appeal to someone who can see through this mess and provide the key to success!
    highFly376

    Let's see if I can get this straight.
    You have an Airport Extreme base station that is set to "Create a wireless network" and you have the box checked for "allow this network to be extended"....
    Then you have an Airport Express that is set to "Extend a wireless network" which you selected the name of your network in the box...
    Correct?
    See this Apple document:
    http://support.apple.com/kb/HT4259?viewlocale=en_US&locale=en_US
    The wireless unit on the right of the diagram can be either of the newer Apple base stations.
    Extreme, Express, Time Capsule

  • How can I expand my wireless network with a Time Capsule and Airport Express?

    My entire house is wired for ethernet access (2 floors).  I have a Time Capsule on the 2nd floor that reaches the entire house except for one room. 
    In this one room I have an ethernet port plugged into an Airport Express. 
    The problem I encounter is that I have two separate wifi networks with two separate names.  I realize I can extend the wireless network on the 2nd floor to the 1st floor but I can only do this wirelessly to my knowledge, and the entire problem is that the signal doesn't reach the front room.  Also, there is really no place in-between that the AE can be placed to extend the reach.  The building is concrete and steel, I think that has a lot to do with the problem.
    My question is: Can I have two wireless routers (connected to the same home network via ethernet) broadcast the same wifi network?  I also have a SONOS system that further complicates things, I'm afraid.  Would it help if I drew some sort of diagram?
    Thanks!

    Your network is not working as you describe.. or I have misunderstood the layout..
    What is the broadband type? Modem is where? What is the main router?
    From your screen shots the main router is the airport express that covers one room which seems wrong.
    Why isn't the TC the main router? or both bridged.. if you go back and look at the apple document.. one or both apple routers are in bridge mode..
    You are having issues with setup .. half of which is caused by v6 airport utility.
    What OS are you running? Please install 5.6 utility.. do it.. do it now!!
    Easy for Lion.
    http://support.apple.com/kb/DL1482
    Messy but possible for ML.
    How to load 5.6 into ML.
    1. Download 5.6 for Lion.
    http://support.apple.com/kb/DL1482
    Click to open the dmg but do not attempt to install the pkg.. it won't work anyway.
    2. Download and install unpkg.
    http://www.timdoug.com/unpkg/
    Run unpkg on the desktop.. it is very simple.. drag the AirPortUtility56.pkg file over to unpkg.. and it will create a new directory of the same name on the desktop.. drill down.. applications utilities .. there lo and behold is Airport utility 5.6 .. drag it to your main utilities directory or just run it from current location.
    You cannot uninstall 6.1 so don't try.. and you cannot or should not run them both at the same time.. so just ignore the toyland version.. the plastic hammer.. and start using 5.6.. a real tool.

  • Extending an existing wireless network with a new Airport Extreme(802.11n)

    Is it possible to extrend a existing wireless network comprised on a Airport Extreme (g) and a Airport Express with a new Airport Extreme (n) ? and possibly accesss an airdisk? Have tried settng channel to the same (1) but no worky.
    I have had real problems (at least 2 hours with Apple Care to no avail) at getting the new Airport Extreme(n) to connect to the internet (Ozemail/iinet) with PPOE. Authentication when changed to occur at ADSL modem and produces no errors (green light) but no internet still through AE(n). Not Hardware either as both ADSL modem and AE(n) have been changed.
    So as a last ditch attempt, thought I might try extending the preexisting network that works fine so I can access an AirDisk.
    Any reponses appreciated.

    Search this forum for "WDS". Since I am having massive problems myself right now, I can only tell you: Try the two methods mentioned in this thread:
    http://discussions.apple.com/thread.jspa?threadID=944334&tstart=0
    Maybe you're lucky!

  • Extending Sky Wireless Network with Airport Express.

    I spent most of last night trying to extend my Sky Wireless Network using an Apple Airport Express. The Apple Store salesman told me that it would be simple to set up but he's either wrong or I'm completely stupid!
    Does anybody know if this is possible and if so, can they please advise me how I do this. (I am using Windows 7 on my Dell laptop)

    I spent most of last night trying to extend my Sky Wireless Network using an Apple Airport Express. The Apple Store salesman told me that it would be simple to set up but he's either wrong or I'm completely stupid!
    Unfortunately, the salesman may not have understood your question, or he may have given you incorrect information.
    It's possible to have the AirPort Express provide more wireless coverage if you connect it using an ethernet cable permanently to your Sky router.
    But, the AirPort Express cannot "extend" the wireless network produced by the Sky by connecting using wireless only. The "extend" feature will only work if you have an Apple to Apple wireless connection. This feature is not compatible with the products of other manufacturers.

  • Extending home wireless network with 802.11b/g Airport Expresses

    Home Setup: iMac with iSight G5 2.1GHz PPC, OS X Leopard 10.5.8, 2.5GB memory, 2 Airport expresses-802.11b/g.
    Up to just recently, I was able to use my AE's to create a whole house wireless network: one as my main network connected to my cable modem, and the other as a wireless network extender. My extender got pulled out one day accidentally, and when I went to plug it in it wouldn't reconnect to my network...and so the problems began. Airport Utility used to give the option of "Extending the Wireless Network", but no more.
    I've done a lot of searching through the forums regarding this issue, read through the sage advice by superusers Tesserax and Bob Timmons, and attempted to set up my main AE as my "WDS Main" AE and the other as my "WDS Remote". The WDS main connects fine to the internet, but the WDS remote continues to show a flashing amber light and inability to extend my wireless network. I've done soft and hard resets to the remote AE (which transiently gives me a green light, then back to flashing amber), network diagnostics using the Airport utility, but still no luck. The AE wireless extender continues to flash amber and is nonfunctional.
    AE Wireless extender settings reported:
    -WIreless Mode: Create a wireless network
    -Connect using: Ethernet
    AE Errors reported:
    -Ethernet Unplugged
    -Default Settings
    I setup the AE Wireless extender as a WDS Remote, it resets and shows "Normal" without problems reported in the summary window of Airport Utility. Connection indicated as "Airport (WDS)" and Wireless Mode reads "participate in a WDS network", but the AE is still flashing amber and will not connect to the internet or Main WDS wireless network.
    Went to the Genius Bar at the local mac store...they couldn't help at all.
    I'm out of answers...help?!
    Allan

    There are basically two "flavors" of WDS that the AirPorts support: static & dynamic.
    o A static WDS allows for a main, relay, and remote base stations in the configuration. This only operates in the 802.11g radio mode. Its advantage is it is well suited when you are trying to cover a considerable linear range ... like a rectangular house where the Internet connection comes in at one of the shorter sides and you want wireless at the other end. The biggest disadvantage of this type of WDS is that for every base station added, you lose half the overall bandwidth.
    o A dynamic WDS allows for only a single main and multiple remotes. Think of a wheel with the main at the center and the remotes as spokes of the wheel. The advantage of this type of WDS is it operates in the 802.11n radio mode and doesn't suffer a significant bandwidth loss like the static version.
    As a minimum, a dynamic WDS requires two 802.11n AirPorts (or Time Capsules). You can create a static WDS with either all 802.11g AirPorts or a mix of 802.11n & 802.11g AirPorts. Note; however, you cannot create a dynamic WDS with mixed mode base stations.

  • HT4259 How can I extend a wireless network from a 2Wire modem by usingan Airport Express? Years ago I could do this just by plugging in the (old) Airport Express. TIA Travelmonger

         How can I extend a wirelss network from a 2Wire modem using an Airport Express? Some years ago using the old Express I was able to do so simply by plugging on the Express witha minimum of tweaking. Still the same?
    TIA
    Travelmonger

    Still the same?
    Unfortunately, no.
    Apple's newer "Extend a wireless network" feature was designed to only work with other Apple products, so it would be extremely unlikely that it would work with a 2-Wire device if you plan to extend using wireless only.
    If you plan to connect the AirPort Express to the 2-Wire device using a wired Ethernet connection, the Express can be configured to provide more wireless coverage that way.

Maybe you are looking for