Can I extend the range with an Airport Extreme?

Hi there,
Is it possible to extend a wireless network's range with an Airport Extreme (just like you can do with an Airport Express)? Currently I have a Billion wireless modem/router but need to extend the range so I can use my PS3 in my bedroom. I would rather get an Airport Extreme instead of an Express so I can take it with me when I move out. Just need to know if the Extreme will do this as it doesn't mention it on the website.
Thanks for your time.
Regards,
Daniel

Welcome to the discussions!
+Is it possible to extend a wireless network's range with an Airport Extreme (just like you can do with an Airport Express)?+
The AirPort Express, AirPort Extreme, and even the Time Capsule can "extend a wireless network", +but... they are only compatible if you have another Apple router as the main device.+
Sorry, but none of the Apple products would be compatible to extend the range of your Billion wireless router using wireless only. You might want to check to see if Billion has a "range extender" or similar compatible device.

Similar Messages

  • Can i extend the range of an airport extreme with another airport extreme and use the ports on the airport extreme i used to extend the network?

    That seems like a complicated question. 
    I have a Time Capsule (which the HD *****, but that is matter for another discussion) and want to extend the range with an Airport Extreme because I have 2 devices in one room that do not do wireless but have Ethernet ports.
    The room has iffy WiFy connectivity too.
    I want to know if the 3 ports on the Airport Extreme still work after configuring it as an extender rather than a router.

    The thing is that I want to know if I can put the Airport Extreme at the edge of the room where the existing Base does not reach.
    This will not work.
    Remember, an "extending" AirPort can only extend the quality of wireless signal that it receives. For that reason, it must be located where it can receive a strong wireless signal in order to work effectively.
    For example, let's say that your "main" router was on one end of the house and you want to extend the signal to reach the other end of the house.  In this case, you would locate the "extending" AirPort about half way between the main router and the other side of the house.

  • Can I extend the range of my Airport Extreme with 2 Airport Express units?

    I am using Airport Extreme as my basic router. I have connected 2 airport express units (all new since 12/09) to extend the network about 300 ft into another building to a PC. I am receiving about 65% signal and only one of the express units is extending the signal. Previously I was able to extend the network with a Netgear router and one D-Link extender and achieved 85%.
    I would like to use the 2nd express to extend the signal of the 1st express which is extending the Extreme.
    If this is not possible, can I use something other than an express with the extreme to extend the wireless network?

    Here are the basic steps in setting up a static WDS. Please compare them to what you have done to see if there are any differences. Hopefully, this will give you a clue on what to try.
    AEBSn - WDS Setup
    (Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete. Also, jot down the AirPort IDs (MAC addresses) for each of the base stations to be used in the WDS. The AirPort ID and is printed on the label on the bottom/side of the base station.)
    Main Base Station Setup
    o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
    o Open AirPort Utility (located in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
    o Select the main base station, and choose Manual Setup from the Base
    Station menu, or double-click the base station to open the configuration in a separate window.
    o Enter the base station password if necessary. If the base station is using the
    default password of public, you will not be prompted for a password.
    o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
    o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
    o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
    o Click the Add "+" button and enter the AirPort ID of the base station you want to connect to this base station.
    o Click Update to send the new settings to the base stations in the WDS.
    Remote Base Station Setup
    o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as a remote base station.
    o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
    o Select the remote base station, and choose Manual Setup from the Base Station menu.
    o Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
    o Enter the same network password as the main base station, if necessary.
    o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
    o Click WDS and choose “WDS remote” from the pop-up menu.
    o Enter the AirPort ID of the main base station in the WDS Main field.
    o Click Update to transfer the settings to the base station.
    Relay Base Station Setup
    o Click the AirPort status menu in the menu bar to join the wireless network created by the base station you want to set up as the relay base station.
    o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
    o Select the relay base station, and choose Manual Setup from the Base Station menu.
    o If the base station is using the default password of public, you will not be prompted for a password.
    o Enter the same network password as the main base station, if necessary.
    o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
    o Click WDS and choose “WDS relay” from the WDS Mode pop-up menu.
    o Enter the AirPort ID of the main base station in the Main AirPort ID field.
    o Click the Add "+" button and enter the AirPort ID of the remote base station this relay base station will connect to.
    o Click Update to transfer the new WDS settings to the relay and remote base stations.
    (ref: Pages 42-46 of "Designing AirPort Networks.)

  • I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

    I'm trying to extend the range of an Airport Extreme 802.11g by adding an Airport Express 802.11n. I set the Express up to join the existing network, but it does not make any difference in the range of the network. What's wrong?

    Let me see if I can help you with the basic WDS configuration steps:
    Note: To help facilitate the setup, temporarily connect the AXn directly to the AEBS LAN port using an Ethernet cable. Once the setup is complete, you can move the AXn to the desired location. For all configuration steps you will be using the AirPort Utility. Before starting, be sure to jot down the AppleIDs for both base stations.
    802.11g AirPort Extreme Base Station (AEBS) Configuration
    AirPort Utility > Select the AEBS > Manual Setup > Wireless tab
    Wireless Mode: Participate in a WDS network
    Manual Setup > WDS tab
    WDS Mode: WDS main
    Allow wireless clients (checked)
    WDS Remotes: <enter the AppleID for the AXn here>
    Click on Update and allow the base station to restart.
    802.11n AirPort Express Base Station (AXn) Configuration
    AirPort Utility > Select the AXn > Manual Setup > Wireless tab
    Wireless Mode: Participate in a WDS network (Note: You may have to hold down the Option (Mac) or Control (PC) key to see this option in the list.)
    Manual Setup > WDS tab
    WDS Mode: WDS remote
    Allow wireless clients (checked)
    WDS Main: <enter the AppleID for the AEBS here>
    Click on Update and allow the base station to restart.

  • External antenna to extend the range of an Airport Extreme 802.11g

    What is the best external antenna for extending the range of my Airport Extreme? My studio is in an old metal building and I want to send the single to my house which is about 50' away. The metal blocks the signal so I believe I need some kind of directional antenna. Any advise?

    Here are a few you can check out ...
    o Dr. Bott's ExtendAIR Direct Antenna
    o QuickerTek 27dBm Transceiver

  • How to extend the range of my Airport Extreme network by adding an Airport Express

    How to extend the range of my Airport Extreme network by adding an Airport Express?

    You have to make sure that the AirPort Express is in Factory Default Settings. If it is straight out of the box, it is ready to be configured.
    The instructions that I will provide are for using AirPort Utility 6.0, which you have.
    Locate the Express in the same room as the AirPort Extreme for the configuration. Power it up and allow a full minute for the Express to display a blinking amber light.
    Make sure that the wireless is turned on your Mac
    Open AirPort Utility 6.0 and look at the small rectangle in the upper left hand corner of the display. It should now read something like "Other AirPort Base Stations (1)"
    Click on the rectangle, and then click on the AirPort Express xxxxxx listing
    AirPort Utility will take a minute or two to analyze the settings on your network and then suggest that  the Express be configured to "Extend" your wireless network.
    Edit the Base Station name to your liking, then click Next in the lower right hand corner
    Allow a full minute or two let AirPort Utility do its work
    When you see Setup Complete, click Done at the lower right of the window.
    Now move the AirPort Express to a location that is approximately half way between the AirPort Extreme and the area that needs more wireless coverage.
    You should be in business.

  • I have an old airport that still works, can you use it the same way that one uses an airport express to extend the range of an airport extreme base station?

    It would save me a few bucks if I could use an old airport that I have to extend the range of a new airport extreme.  My concept would simply be to use the old Airport the same way I would use a newer Airport Express as a slave repeater.  Is this doable?

    Both the new AirPort Extreme and older AirPort Express will have to be configured using Apple's WDS settings to provide more wireless coverage. 
    Here are the downsides:
    WDS operates only at "g" wireless speeds, so you will lose all of the faster "n" wireless capability of the new AirPort Extreme
    WDS cuts the bandwidth on the entire network in half, so you will have a "g" wireless network running at half speed.
    WDS is difficult for most users to configure because it is easy to make a mistake and hard to recover without starting all over again
    Bottom line......Saving a few bucks will be very costly in terms of performance on your network.

  • Can I increase the range of an AirPort Extreme by a router other than AirPort Express?

    Im using an AirPort Extreme as my primary wireless router extended by an AirPort Express at home. We are primarily using macs at home and I'm overall satisfied with the quality of the product. However a lot of online reviews (including pcmag and cNet don't list the extreme or the express) amongst the list of top 10 wireless routers. The ones listed are much cheaper and has received very positive user reviews as well. However I need to setup a new network at my new office and I have some questions regarding setting up a wifi network in regard to AirPort Extreme:
    1) Can I extend the wireless network setup via AirPort Extreme Base Station by another wireless router other than Airport Express?
    2) I've heard of many cheaper alternatives (Cisco and NetGear being chief) to AirPort Extreme. I've also heard that the network set up by the AE is not as compatible with a windows based environment (which could be an issue as I'm going for an IBM server). In that case which would be the best wireless router for me?
    3) Any other specific reason for which I should prefer AE over any other wireless modem?
    Any help would be appreciated. Thanks.

    1) Can I extend the wireless network setup via AirPort Extreme Base Station by another wireless router other than Airport Express?
    Apple appears to have designed their "extend a wireless network" feature using proprietary software, so it would be extremely unlikely that a router from another manufacturer would work with the AirPort Extreme....if you are trying to extend wirelessly.
    In that case which would be the best wireless router for me?
    That depends on your requirements, and whether you are going strictly for specifications rather than features, or even ease of installation and use. In any case, I can't answer that question.
    If you subscribe to industry publications with test reports on products, there always seems to be a new "best" product, so expect that whatever you buy will be superceded by another "best" product within a month.
    As far as use with a PC, I've had no issues using several PCs with Apple routers.
    3) Any other specific reason for which I should prefer AE over any other wireless modem?
    Apple routers are for mom and pop at home. While the product would provide basic functionality in an office, the product was not designed, nor does it have the type of features that most businesses would require.
    For example, if I were using a business router, I would expect it use a high grade firewall for security purposes, and for the router to provide reports that track Internet use for each computer, along with a record of what Internet sites were being visited by each employee. Apple routers won't do that.

  • Can I extend a network with an AirPort Extreme Base Station Rather than with an Express?

    Topic title pretty well sums up the question.
    I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
    We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
    So, can the Extreme act as an "extender" only, in lieu of using an Express?

    pcbjr wrote:
    Topic title pretty well sums up the question.
    I have a TimeCapsule Base Station with two Expresses for extending the network through the house.
    We're doing a 3 room addition, and there is not a convenient place to put an Express in a wall outlet in the middle room of the addition, but there's a perfect place to put an Extreme on top of a piece of furniture.
    So, can the Extreme act as an "extender" only, in lieu of using an Express?
    Hiya.
    You can absolutely extend a network with an Extreme. I've got a 5th gen. Extreme extending a network created with a 3rd gen. Time Capsule. On the Extreme, you'll have the option to allow (or not) WiFi clients. I recommend having all units updated to the current firmware (7.6.1 as of this writing). Note that extending doesn't work in daisy-chain fashion, meaning that your Expresses or Extremes will each connect to and extend from the TC. As such, you'll want the TC to be in as central a location as possible to offer the best coverage.

  • What cables are needed to extend the range of my airport extreme with my time capsule

    I just purchased a new Time Capsule, and I want to install it and use my current Airport Extreme to extend our home's wireless network. What extra cables are needed, and is there a diagram for this setup? We currently have a broadband network.

    Apple's instructions to do this are here:
    http://support.apple.com/kb/HT4260
    You will need an Ethernet cable to connect your new Time Capsule to the AirPort Extreme.

  • Using an Airport Express to extend the range of my Airport Extreme.

    i've just bought an Airport Extreme and an Airport Express so i can connect my MacBook in my bedroom (second floor) to the DSL modem in the basement.
    i was able to configure the Extreme as a base station but cannot figure out how to configure the Express to use as a relay.
    no matter what i do, i cannot get the Express to show up in the Airport Utility, even when i have it powered in right beside the Extreme base station in the basement.
    please help!

    I have found that you need to have an Ethernet cord connecting the Airport Express to your Mac to set up the Express to work on WDS with your Extreme. Once it is set up, you should be able to see both the Extreme and the Express wirelessly, but for setup you need the wire to the Express.

  • Help! Im trying to extend the network on my Airport Extreme with an Express

    This is probably such a begginers question but it has truely boggled my mind for the last 24 Hours!
    I have brought an airport express to extend my airport extreme network. My Airport extreme is the base and is hooked up to my initial Home model from my ISP which works fine.
    I have been trying to connect my airport express and am having no luck. I have plugged the airport in but am having no luck locating it on my airport utility (only my actual Airport Extreme shows)
    Can someone please help me Ive been here for hours reading on forums trying to sort this out and Im gettin nowhere fast!
    The light on the express is flashing orange. I have tried to reset it but there still is nothing showing.
    any ideal on what i could do or follow step by step?

    Ok, the question is how can i extend the range with
    my airport extreme base,
    With an Airport Express or another Airport Extreme
    I have A netgear WNP802, it
    has a repeating feature.
    Which won't work with your Airport Extreme
    < But i am wanting to have the
    netgear and the apple airport extreme talk to each
    other so that i can put the net gear in a seperate
    room to extend the range of signal. </div>
    This is not possible.
    How can i do this?
    You can't.
    Netgear and Apple use different chips which means they won't and can't talk to each other when it comes to extending networks.

  • How to extend the range with a second Airport Express? Do I need a DSL cable?

    How to extend the range with a second Airport Express? Do I need a DSL cable?

    Thanks, now we need a bit more information, please, in order to provide you with the correct information that you need.
    I assume that you already have one AirPort Express.....either a model A1264 or A1392.....set up and operating OK, is that correct?
    If yes, you can extend the network either by using wireless or an Ethernet cable with a second AirPort Express.....either the A1264 or A1392 model. A wired connection is the way to go, if possible, since it provides better performance.  But, wireless might work OK for you if you want to try that.
    Let us know "how" you want to extend......wireless or wired?

  • I get a neighbor's wifi on my MacBook in my bedroom.  How can I extend the range to the MacMini in my living room?

    I get a neighbor's wifi on my MacBook in my bedroom.  How can I extend the range to the MacMini in my living room?

    You can't. It's not your network.

  • How can I extend the range of my chart?

    I've asked this question before on here, and found that shift-clicking for more cells has usually worked, but I have now run into a new problem...
    My chart used to cover the range B5:P50. However, since moving a column it now only covers the cell range H5:P50. My chart is on a separate sheet. Usually if I want to add more to the range it will be downwards, so I just click on the chart, then click on the Main Sheet and shift-click to add more cells. Unfortunately, because the range I want is to the left of the highlighted area this time, I can't use shift-click.
    How can I extend the range of my chart so it includes cells to the left of the currently selected range? In Excel I'd be able to just type the range in a box somewhere, rather than all this GUI-based clicking and dragging which is actually more difficult! Is there somewhere I can just type the range in that I want?
    Thanks!

    "I want to add some series that are missing from the chart. How do I do that?"
    Here's a two step process to do that:
    Select the chart to show the the data selection on the associated chart.
    Click in the leftmost column of the data, and drag left to change (move) the selection (blue arrow) for the result below:
    Grab the control handle (small circle) at the bottom right corner of the selection, and drag  right, as indicated by the blue arrow.
    Result shown below.
    Reassign colours and do other formatting as desired.
    Regards,
    Barry

Maybe you are looking for