Can I install a Lacie D2 Drive in my Mac Pro

newbie question, sorry!
I have a Lacie D2 500 gig external drive that has crapped out on me. I was told that it could be possible that the enclosure is the problem and not the drive itself. If I take the drive out of its enclosure can I install it in one of the Bays in the mac pro?
thanks

okaypaddy wrote:
newbie question, sorry!
I have a Lacie D2 500 gig external drive that has crapped out on me. I was told that it could be possible that the enclosure is the problem and not the drive itself. If I take the drive out of its enclosure can I install it in one of the Bays in the mac pro?
thanks
It could just be the dead/defective power adapter Lacie seems to be a known for. Before you crack the drive open, i would strongly recommend that you test it with a known, working power adapter. Perhaps a friend with the same drive? If you're lucky, i've seen some of the Lacie drives set up in Apple Retail Stores, and perhaps an employee might let you test your drive there. Worst case scenario, you could order a new adapter which will set you back $19.00.
http://www.lacie.com/us/products/range.htm?id=10030

Similar Messages

How can I install Windows7 -64BIT on a 1st Generation Mac Pro 2.66GHZ Quad?

Hi,
I posted this in Bootcamp but haven't received any replies so I am reposting it here where perhaps it really belongs.Is it possible to install Windows 7 64 bit on a 1st Generation Mac Pro 2.66Ghz?
Apple suggests that it's not possible and yet I've seen several Googled posts where the users have successfully installed 64 bit on a 1st Generation Mac Pro. The problem is that they've done this creating a bootable iso disk(whatever that is) using a Windows computer with imgburn and windows commands. I'm pretty good at following instructions but I haven't seen any instructions on how to install Windows 7 on this machine using a Mac based approach.
I'm using BootCamp and was able to partition the drive into NFTS and "proceed" with installation; however all the installations failed during setup and Windows would not boot; disk repair was not possible. Besides, from what I've gathered, 32 bit is problematic around memory issues.
When I try installing 64 bits, I never get past the "select cd rom 1 or 2" message where the keyboard won't work. It is at this point where others say they have successfully proceeded with moving forward by creating a bootable iso disk.
Problem is it's all Windows based with exe files and presupposes I already have Windows running.
I'm not sure I really understand how to create an iso disk, but I do have ROXIO TOAST 10 which is capable of burning "ISO" disks.Does anyone know how to do this and/or can you point me to a place where there are instructions on how to proceed?? While I realize Apple says that some mid 2006 mac pros aren't supported, there are multiple posts of windows 7 users successfully installing Windows 7 on a 1st Generation Mac Pro.
Thanks.
Mac Pro 2.66GHZ Quad Core

I have a March 2009 Mac Pro dual quad core running Win7 Pro 64 bit. I have Windows installed on a dedicated internal hard drive. There are no partitions, the entire drive is for Windows use.
Here's how I installed it, I did not start with BootCamp. Make sure the drive you're going to use for Windows doesn't have any important files on it because it will be formatted.
1. Update Snow Leopard
2. Place the Windows cd in the Super Drive
3. Shut down the computer
4. Remove all the hard drives except the one you want Windows installed on. Keep track of the order they are in and at the end replace them in the same order.
5. Boot the computer holding down the Option key
6. Boot to the Windows cd
7. Install Windows and format the drive to NTFS
8. When Windows needs to restart during installation you'll need to hold the Option key and boot to Windows, not the Windows cd.
9. After Windows installs, place your Snow Leopard disc in the Super Drive
10. The Drivers for Windows will be installed along with a Windows version of BootCamp.
11. Go to Start > All Programs > Apple Software Update
12. Update again until it's done.
13. You'll also find a BootCamp under Control Panel, check it out.
14. Shut down the computer and replace the hard drives in their original order
14. Now if you turn on the computer it will boot to Snow Leopard, but if you hold the Option key during boot you can select Windows or Mac.

Can I install a solid state disk in my Mac Pro Early 2009?

Can I install a solid state disk drive in my Mac Pro Early 2009? Is there an adaptor?

see here
http://macperformanceguide.com/Mac-InstallingSSD.html

Can I install an internal hard drive in i-mac intel 17" ?

Where can I get an internal hard drive compatible for intel i-mac? I need a larger hard drive, like 250gb or something. Can I install it myself?

You can go to a apple service center like CompUSA and have them install one for you. If you buy the drive from them, they will install it for free, otherwise it is like a 40 dollar charge. DO NOT attempt to install it yourself, not only will you void your warranty, the intel iMac is very difficult to open and work on and you will probably break something.
Glor

Can I install an additional hard drive to my Macbook Pro? (2 Hard drives)

I was wondering whether I could install a second hard drive to my 2011 Macbook Pro (2.0 GHz, 500GB HD 4GB Ram) making a total 1TB hard drive space?

There are third party solutions out there, however be warned they will most likely void any current warranty - as it involves removing your optical drive. I don't have details on them myself, but when my apple care expires I might consider that on a Late 09 model and push it to dual SSD's

4 Questions re installing a second Optical Drive in a Mac Pro (Harpertown)

For years I have owned and used a Sony DRX-810UL-T optical drive as an external unit with my Mac Pro "Harpertown" purchased on February 19, 2009. It was connected to the computer using the firewire cable and it worked correctly.
Some Background
Today it dawned on me I had an empty optical drive bay in the Mac Pro so I should move the Sony drive in there and eliminate a bit of the clutter on my computer desk. I read the section on installing optical drives in the little Apple manual that came with my computer but it only discussed a single drive installation.
Checked on line and found several sources describing how to do this and a couple of YouTube videos also showing how to do this. (Oddly only one of the videos mentioned the need for plugging in the power cable).
I made sure I plugged the cables into the proper units as both had helpful legends on them indicating which was for the top drive and which was for the bottom drive.
After installation I powered up and found neither drive would appear.
Checked the About this Mac item in the Apple menu and got confirmation that the system didn't see any drives. Opened the computer again and unplugged the Sony's power and data cables then closed the computer and fired up again.
The original Super Drive again appeared and worked correctly.
The Questions:
1. Since the Super drive came with the Mac Pro and was in the top space can I assume it needed to stay there and not get moved to the lower space?
2. Since the Sony DRX-810UL-T has the correct connectors does this indicate this drive can be used with the Harpertown Mac Pro?
3. If it can, did I miss setting some jumpers? I noticed both drives have one jumper in place but each appears to be in a slightly different spot than the other.
4. Since the Sony drive worked correctly with my current OS (10.6.6) using the firewire cable can I assume it does not need a firmware update to be used internally.
Wrap up
Since the original Super Drive is working properly I am sure I did no damage to it or the computer. It would be nice to be able to get the Sony DVD drive to work internally, however.
Thanks, in advance, to anyone who can offer some help with this situation.

hatter,
Thank you for this added information. Here's the current status of things.
Just to check that the Sony drive would work internally I disconnected the superdrive (ata cable and power cable) and made the Sony drive the only drive plugging it in as if it was the top drive. The jumper for it was set to cable select.
The Profiler found it and listed is in both the ATA section and the disc burner section.
I checked the jumper on the superdrive to be sure it was also set for cable select and plugged both drives back in using the top connections for the super drive and bottom connections for the Sony,
Again only the SuperDrive appears in the ATA list and and the disc burner list.
I am beginning to wonder it the problem may actually be with the ribbon cable that snakes back to the motherboard.
Since that cable has a set of dual outlets at the drive end and has them labeled for top and bottom, is it possible to plug in only one drive using the bottom connector as a test to see if data flows to the motherboard?
Is it possible some part of that cable has somehow become disconnected at the motherboard?

I want to install a second disc drive in my mac pro - which ones?

I have always had all-in-ones. I now have a mac pro, and I love it. I have many disc drives of varying sorts lying around my place, most from older windows towers, but one cd-rw drive from a round base imac. Since I could never do these types of expansion on my old macs, I have no clue what will hook up in my empty drive bay.
This drive from the apple is a... sony cd-r/rw drive unit crx170E/. can I put it in my mac pro's second slot?
If so or if not, can someone briefly explain the types of cd-r connections that would/would not work so i understand the concepts?

Oh alright. Here is the same drive someone put up for sale, just in case I was speaking wrong.
http://cgi.ebay.com/Sony-CRX170E-CD-R%2FRW-Drive--Internal_W0QQitemZ130167812083 QQcmdZViewItem
Do I need to do anything special? or will in function right as soon as I get it installed?

Installing a Blu-Ray Drive in my Mac Pro...

I am considering installing a Blu-Ray drive in my second drive location on my mac pro. The drive I am interested in is this one:
http://www.videoguys.com/bdr202.html
When I spoke with the gentlemen there, he advised me that he didn't believe it would fit in the Mac Pro. How could that be? Isn't there a standard size for all media drives like DVD, CD, and blu-ray drives? Anyone know for sure if this will fit?

It is a standard sized drive and WILL fit
Although you should always be mindful to be sure that you have remove ALL bezels which can interfere with the drive fitting else the drawer mechanism. The easy way to be sure is to make it look exactly like the SuperDrive. The one that is typically missed is the bezel that's right on the end of the drawer. It can be had to spot but it's there.

Can't install OSX 10.7 Lion on old Mac Pro...

i've got an old mac pro... i think it is 2007 or 2008 vintage... it is the 2.66mghzzz model...
it is so old it can't run OSx 10.8 and up... so I am stuck running 10.7xxx
anyway, system disk died recently...
made an OSX 10.7 install thingy on a 8gb USB drive using my new Macbook Pro...
problem is the install keeps hanging after starting the install... i've attached screenshots showing how far it gets...
i've let it sit for a few hours and no progress... i reckon it should normally finish installing of a USB stick in maybe 30 minutes or so?
is it possible that the 4tb SSHD drive i am installing onto is too big for this machine?
it has been using other 4tb drives so not sure this is an issue?
really stuck here... argh...
thanks

thanks for your reply...
yes, I realize it will only install on older macs... my Mac Pro is the 1,1 model... the 2.66mhz processor is from the 2006-2008 era....
i believe it shipped with 10.4 or 10.5 OSX...
it was previously running 10.7.5 which is the newest OSX that was allowed to be installed on it....
so it should allow 10.7 to be installed? Or do I have to start with the much older osx?
I downloaded Lion 10.7 from the mac app store and it of course wouldn't let me install it on anything, even the 4tb SSHD drive when I connected it via USB/SATA adapter to macbook pro as it is too old for running 10.7 install on this machine but I was apple to use SuperDuper app to make a boot drive of the 10.7 download form the mac app store onto a 8gb USB flash drive and make it bootable...
The 4tb SSHD drive appears to work on system as I can run disk utility and format it and mount it etc etc...
Perhaps there is something wrong with my install USB flash drive I made? I am really stuck here...
thanks for your help...

Install RAID and SAS drives in my Mac Pro

Hello,
I have a couple of Mac Pro machines and I want to install extra drives.
I want to install 2 extra SAS 300GB drives.
I take it I need to install a RAID card also.
Will the drives connect to the RAID?
I don't want them to mirror I simply want them as single drives that I can use for storage.
My main concern is will I be able to mouint and access these SAS RAID drives without having to reinstall the OSX System?
Thanks,
Dean

Not quiet sure I follow your plan here.
I want to install 2 extra SAS 300GB drives.
OK, no problem, assuming you have 2 spare bays.
I take it I need to install a RAID card also.
OK, no problem there, either, assuming you have a spare slot.
Will the drives connect to the RAID?
Umm, if you connect them, yes. It doesn't happen automatically
I don't want them to mirror I simply want them as single drives that I can use for storage.
This is what I don't understand - why use the RAID card if you're not planning on RAIDing the drives?
My main concern is will I be able to mouint and access these SAS RAID drives without having to reinstall the OSX System?
If these are additional drives it won't affect the existing system at all. They're completely separate.
If, on the other hand, you want to take the existing system and move it to a RAID volume then yes, you'll need to do some kind of work to preserve your data, but it's not clear that's what you're trying to do.

Can I move an SSD Boot Drive from a Mac Pro 1,1 to a newer 5,1?

I have a MacPro 1,1 (2 x dual core Xeon, 3.0 GHZ) with 8GB RAM and updated with an ATI 5770 video card, driving a 27" Cinema display; I'm running OSX 10.7.5. There's an SSD boot/OS/App drive, and the data is on a secondary hard drive with backup to the data on an identical third drive. Because it's time to update (I've had this flawless machine for nearly 4 years but need one with 64-bit capability) I've arranged to buy a 2010 Mac Pro 5,1, also with a 5770 card. I don't need the hard drives that are in that "new" one. I would like to just swap the three drives I have in the old one, and put them in the new box. Will I encounter any problems?

There are two types of base Systems:
a) "shipped in the box" with a specific model Mac. These will boot only that model, and software Update does not change that capability.
b) "Full Retail" or "Purchased" (even for $0). These will boot any appropriate Mac, because they contain "Drivers for every appropriate Mac."
Your 10.7 computer shipped with software much older, so I presume you purchased that 10.7, and would therefore expect it to boot any appropriate model Mac.
"A Mac can generally boot software no OLDER than what it originally shipped with."
This table shows the original shipping versions (some of which are custom builds) for these models:
Mac Pro
Date introduced
Original Mac OS X included
(see Tips 1 and 3)
Later Mac OS X included
(see Tip 1)
Mac OS X Build(s)
(see Tip 2)
Mac Pro (Late 2013)
Dec 2013
10.9
10.9.2, 10.9.4
13A4023, 13C64, 13E28
Mac Pro (Mid 2012)
Jun 2012
10.7.3
10.8, 10.8.3
11D2001, 12A269, 12D78
Mac Pro (Mid 2010)
Aug 2010
10.6.4
10.7, 10.7.2, 10.7.3
10F2521, 10F2554, 11A511a, 11C74, 11D2001
Mac Pro with Mac OS X Server (Mid 2010)
Aug 2010
10.6.4
10.7, 10.7.2, 10.7.3 (Server)
10F2522, 11A511a, 11C74, 11D2001 (Server)
Mac Pro (Early 2009)
Mar 2009
10.5.6
10.6
9G3553, 10A432
Mac Pro (Early 2008)
Jan 2008
10.5.1
10.5.2, 10.5.4
9B2117, 9C2031, 9E25
Mac Pro
Aug 2006
10.4.7
10.4.8, 10.4.9, 10.4.10, 10.5
8K1079, 8N1430, 8N1250, 8K1124, 8P4037, 8R3032, 8R3041, 9A581, 9A3129
Mac OS X versions (builds) for computers
This table show that any build after 10.6.4 (custom) should work to boot a Mac Pro 5,1 2010.
CAUTION: the last version shipped on a "Full Retail" DVD was 10.6.3, which will NOT boot that Mac directly.
NB> If staying with 10.7, you should check whether you are running 64-bit kernel. If not, a terminal command and a re-Boot will fix that.

Can I take the old hard drive from a Mac Pro G5 and put it into a Mac Pro Dual Xeon?

Hello,
I have an old Mac Pro G5 that still runs fine but the video card is bad so you can't see anything. Can I take the hard drive out of the G5 and put it into the Mac Pro Xeon without losing the data on it?
Thanks!

jenniferfromescanaba wrote:
Even if I go from the hard drive on the G5 to the next generation up from the G5 and put in that hard drive into that next generation up from the G5? Isn't the mounting nearly the same?
The storage bays are physically different from those in a G5. G5's had two bays in ther upper reat of the chassis, the Mac Pros have four slots running front-to-rear two thirds of the way up the chassis.
But as The Hatter says, you can use the G5 drives but may need to "manage" the data transfers.

Can I boot a pulled hard drive from a Mac Pro on an external dock?

I have a 2008ish Mac Pro that has a dead video card and a few other problems. Luckily, the hard drive is still functioning. Is it possible to pull the drive and boot it using an external dock in order to image the drive so I can use it on another computer?

Yes.
Clone using Restore Option of Disk Utility
1. Open Disk Utility in the Utilities folder.
2. Select the destination volume from the left side list.
3. Click on the Restore tab in the DU main window.
4. Select the destination volume from the left side list and drag
it to the Destination entry field.
5. Select the source volume from the left side list and drag it to
the Source entry field.
6. Double-check you got it right, then click on the Restore button.
Destination means an external drive. Source means the docked drive.

Can I install the ddr2 pc5300 memory from my Mac Pro 1,1 in a Mac Pro 3,1 that requires ddr2 pc6400?

I have replaced a Mac Pro 1,1 with a used Mac Pro 3,1. I am trying to canibalize as much as I can. Will the slower RAM from the 1,1 work in the 3,1? Dare I just stick it in and try, or might I cause damage?

I don't quite understand. I do plan to try installing the old ddr2 pc5300 667 from my Mac Pro 1,1 into my Mac Pro 3,1 one pair at a time, just to confirm each pair is in working order and happy in its new home. I have 8x2 GB of RAM I hope to move.
I am uncertain what you have said from there. Yes, the cost would be cheap, free in fact! Is this what you meant? You had suggested buying 667 from Amazon, or similar -- but I don't need. And you have made the point that 8 DIMMs is beneficial--which I will have covered. (great tip)
I think what I am most uncertain about is the comment about what will run cooler. Maybe you mean if I purchased newer memory, the design has become more efficient, so the expense is worth considering?
Thanks in advance!

Can't install my Mountain Lion again on my Mac Pro -- help please.

I can't install Mountain Lion again on my Mac Pro: got this message: This copy of the Install OS X Mountain Lion application can't be verified. It may have been corrupted or tampered with during downloading. Delete this copy of the application, and go to apple store ...

Well, the hard disk has been replaced and the Apple people replaced but innstalled the older OS (
X Lion 10.7)! So I tried to reinstall the newer OS which from App Store under Purchases but I had the problem I stated earlier: This copy of the Install OS X Mountain Lion application can't be verified. It may have been corrupted or tampered with during downloading. Delete this copy of the application, and go to apple store ... Hopefully, I can get this fixed! thanks!

Can I install a Lacie D2 Drive in my Mac Pro

Similar Messages

Maybe you are looking for