Can I install Windows 8.1 on my mid-2010 MacBook Pro?

Can I do it or I will get an error saying that it is incompatible and cannot be installed?
I need to know before I buy. As far as I am concerned I does meet the minimum system requirements suggested by Microsoft by a long shot. Will boot camp allow it?
Regards.

try this:
http://store.apple.com/us/browse/guide/windows#topic-1

Similar Messages

  • Can I install Windows 7 System Builder Addition on a MacBook Pro?

    Can I install Windows 7 System Builder Addition on a MacBook Pro?

    rmsmac,
    do you mean Addition, or Edition? Is it a 32-bit version of Windows 7, or a 64-bit version of Windows 7?
    Why don’t you give it a try, and report back on whether you’re able to or not?

  • How to install Windows 8 or 7 on Mid 09 Macbook Pro (10.9 Mavericks)?

    hello fellows
         i have a macbookpro mid 2009 , i had installed windows 7 on 10.8 and using well .
        Two days earlier, i upgraded the ssd and installed the 10.9 on my laptop.  but i cross into trouble when  install the windows.
         i have follow the instructions that windows 8 installation on 10.9 by using a usb,  and i have a bootcamp partition. but the screen stay white after system reboot.
         did anyone have installed windows 7 or 8 on mid 09 with 10.9 Mavericks successful ?

    Welcome to Apple Support Communities
    Your MacBook Pro is not designed to install Windows through an USB drive, so do not use this option. You are getting a white screen because your MacBook cannot start up from the USB drive with Windows.
    Instead, use a DVD with Windows, so you will be able to install Windows. Follow these steps > http://manuals.info.apple.com/MANUALS/1000/MA1636/en_US/boot_camp_install-setup_ 10.8.pdf
    Mid 2009 MacBooks Pro do not support Windows 8 officially

  • HT3986 i can not install windows 7 with boot camp on my macbook pro 17-inch eairly 2011

    I have been trying to install windows 7 on my MacBook pro 17inch 2011, once i get to the step "burn a copy to a cd or DVD" the system runs and burns the information to the DVD but when the next step appears after I create the partition the program dose not recognize the DVD I created. when i save the copy to an external hard drive that is MS-DOS (FAT) formatted the same thing happens, the system just does not recognize the saved file. I have updated my computer and tired to check if I have any updates for the boot camp were available my current version is 4.0.1 (429). if there is anyone out there who can help, please do. 

    1st, you read the full guide, and you understand that you need to supply your own copy of Windows 7 (Home Premium preferably 64-bit).

  • I have a mid 2010 Macbook Pro, How can I install Windows 7 without an Optical Drive?

    For clarity:  I have a mid 2010, Macbook Pro.  I recently decided to upgrade to a Crucial SSD drive, double the ram (8 gigs), and remove the optical drive in favor of using my old drive as a back up.  I am also currently running Yosemite.
    I want to install Windows 7 onto my SSD, using bootcamp.  Unfortunately I no longer have an optical drive installed, which makes things difficult as Bootcamp does not even give me the option to create a bootable USB.
    Now, this is where things get kinda fuzzy:
    MId 2010 macbooks use EFI, and are quite capable of booting from USB.  How do I know?  Because I booted from a USB drive in order to do a fresh install of Yosemite on my SSD.
    I have read mutliple forums and threads with claims that folks have had no problems doing this on 2008 Macbook Pros running Snow Leopard.  However, what seemed to be required was some clever .plist modding.  I have used both text wrangler, and x-code to do this, unfortunately upon booting of bootcamp, bootcamp instantly crashes.  Naturally, I can restore bootcamp because I made backups of the .plist file.
    It would seem that modffying the .plist file assumes that the option to create a bootable USB device is grayed out.  In my case, it is non existent.
    I have also read that folks have had success using rEFIt, however rEFIt has been forked to rEFIned, and the developer of rEFIned made mention on his site that Yosemite handles booting differently than previous versions of OSX.
    WIth that, I was hoping that some kind person could explain to me whats going on, what I am missing, and what I can do to make this happen just shy of tearing down my MBP and reisntalling the Optical Drive and dusting off my Win 7 disc.
    Also, my Model Number/Bootrom is MBP 6,2.
    Thanks in advance!

    Thank you for your reply, and the information.  This is what I came up with:
    I added the strings as instructed, however when I went to sign the script in terminal, I was told:
    /Applications/Utilities/Boot Camp Assistant.app: replacing existing signature
    /Applications/Utilities/Boot Camp Assistant.app: code object is not signed at all
    In subcomponent: /Applications/Utilities/Boot Camp Assistant.app/Contents/info.plist
    Also, here are screen captures of the lines that I added.  Mine are the top string entries:
    Thank you for your help, thus far!

  • Problem install windows on mid 2010 MacBook Pro 13 with 10.9.1

    I run into problem install windows on mid 2010 MacBook Pro 13 with 10.9.1.  Boot Camp Assistant shows error "Can't install the software because it is not currently available from the Software Update server.".  So what is the problem and how can I work around it?  I also tried to only chose "Install Windows 7" option, but it could not recognize my windows dvd (which I created from ISO).  Any help is appreciated.

    I run into problem install windows on mid 2010 MacBook Pro 13 with 10.9.1.  Boot Camp Assistant shows error "Can't install the software because it is not currently available from the Software Update server.".  So what is the problem and how can I work around it?  I also tried to only chose "Install Windows 7" option, but it could not recognize my windows dvd (which I created from ISO).  Any help is appreciated.

  • HT1270 My mid 2010 MacBook Pro has the maximum 8 GB memory cards installed. Can it be upgraded to 16 GB? Are there compatible 8 GB cards available?

    My mid 2010 MacBook Pro has the maximum 8 GB memory cards installed. Can it be upgraded to 16 GB? Are there compatible 8 GB cards available?

    I have a similar question..  13" macbook pro, mid 2010- having problems with spinning beach ball..  like someone from Mars has taken over the computer..   - the specs are below..   would it help if I added more RAM?   If  yes, any suggestions where/ what to buy?  This only started after upgrade to Mountain Lion from SNL. 
    MacBook Pro 13 inch mid 2010
      Model Identifier:    MacBookPro7,1
      Processor Name:    Intel Core 2 Duo
      Processor Speed:    2.66 GHz
      Number of Processors:    1
      Total Number of Cores:    2
      L2 Cache:    3 MB
    Memory  4 GB 1067 MHz DDR3
      Bus Speed:    1.07 GHz
      Boot ROM Version:    MBP71.0039.B0E
      SMC Version (system):    1.62f7
    Graphics  NVIDIA GeForce 320M 256 MB
    BANK 0/DIMM0:
      Size:    2 GB
      Type:    DDR3
      Speed:    1067 MHz
      Status:    OK
      Manufacturer:    0x80AD
      Part Number:    0x484D54313235533654465238432D47372020
      Serial Number:    0x27A0B2F9
    BANK 1/DIMM0:
      Size:    2 GB
      Type:    DDR3
      Speed:    1067 MHz
      Status:    OK
      Manufacturer:    0x80AD
      Part Number:    0x484D54313235533654465238432D47372020
      Serial Number:    0x2740B300

  • I can't install my old logic 8 on my new macbook pro. It says it does not support powerpc applications anymore. what do i need to do?? this is ridiculous!!!

    I can't install my old logic 8 on my new macbook pro. It says it does not support powerpc applications anymore. what do i need to do?? this is ridiculous!!!

    Logic 8 will probably run on your new machine but the installation program contains some older PPC code for pre Intel Macs. This was not a problem as all OSX versions contained the "Rosetta" PPC emulation, that is, up until Lion when all PPC emulation was dropped.
    There are ways to do this however, try searching Google for:  Installing Logic 8 under Lion or Mountain Lion.

  • I can't install any softwares and any update to my Macbook Pro?

    I can't install any softwares and any update to my Macbook Pro?
    <Edited by Host>

    ttlmdy,
    which model MacBook Pro do you have?
    What exactly happens when you try to run a software installation or a software update?

  • Can i run windows xp(no virtualization software) in my macbook pro retina 15 inch mid 2012 . all the bootcamp compatible to my laptop support only win 7 or 8.

    can i run windows xp(no virtualization software) in my macbook pro retina 15 inch mid 2012 . all the bootcamp compatible to my laptop support only win 7 or 8.

    Not without using a VM. XP is no longer supported in Boot Camp or on newer Apple computers.

  • How to get bootcamp to install from USB on Mid 2010 Macbook Pro in Mavericks

    Ok, finally ran into my first problem with Mavericks. It's a doozy. Please if anyone has any advice, let me know.
    My bootcamp partition was acting a little buggy. I also wanted to make the partition larger, so I went ahead and erased it, made a larger partition and was getting ready to install windows 7.
    Unfortunately, little to my knowledge, bootcamp assistant is programmed to not allow installation of Windows via USB if your computer had an optical drive in it's factory delivered form.
    I have removed my optical drive in favor of a second hard drive and encased my original superdrive into an External USB hub.
    There apparently used to be a solution involving editing the plist.info text document to allow USB installation. However, as of MAVERICKS, this document is now locked and unable to be edited.
    I was running windows 7 fine until I scrapped it, and now I have no way to re-install windows short of going through a laborious process of re-installing my optical drive into my laptop, installing, and then re-installing my hard drive back in. The only reason is due to a software bias for my series of laptop because it "used to have" an optical drive.
    Does anyone know of any way that I can bypass this issue to get Windows Re-installed to a bootcamp partition on a mid-2010 macbook pro without using the optical drive?
    Thanks in advance!

    Remove the Boot Camp partition only with Boot Camp Assistant, not with Disk Utility.
    Install or Reinstall OS X from Scratch
    Be sure you backup your files to an external drive or second internal drive because the following procedure will remove everything from the hard drive.
    Boot to the Recovery HD:
    Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
    Erase the hard drive:
      1. Select Disk Utility from the main menu and click on the Continue button.
      2. After DU loads select your startup volume (usually Macintosh HD) from the
          left side list. Click on the Erase tab in the DU main window.
      3. Set the format type to Mac OS Extended (Journaled.) Optionally, click on
          the Security button and set the Zero Data option to one-pass. Click on
          the Erase button and wait until the process has completed.
      4. Quit DU and return to the main menu.
    Reinstall OS X: Select Reinstall OS X and click on the Install button.
    Note: You will need an active Internet connection. I suggest using Ethernet if possible
               because it is three times faster than wireless.

  • Why can't I use my mid 2010 macbook pro with 8GB memoir and NVIDIA GEForce GT 330M 256MB to run 3D in photoshop CC?

    Why can't I use my mid 2010 macbook pro with 8GB memoir and NVIDIA GEForce GT 330M 256MB to run 3D in photoshop CC?

    3-D is very memory intensive.
    System requirements | Photoshop
    Mac OS
    Multicore Intel processor with 64-bit support
    Mac OS X v10.7, v10.8, or v10.9
    2 GB of RAM (8 GB recommended)
    3.2 GB of available hard-disk space for installation; additional free space required during installation (cannot install on a volume that uses a case-sensitive file system or on removable flash storage devices)
    1024x768 display (1280x800 recommended) with 16-bit color and 512 MB of VRAM (1 GB recommended)**
    OpenGL 2.0–capable system
    Internet connection and registration are necessary for required software activation, membership validation, and access to online services.*
    ** 3D features are disabled and some Mercury Graphics Engine enhanced features may not work with less than 512 MB VRAM. Read the Help article.
    Bottom line, you don't have enough VRAM
    Nancy O.

  • I have a mid 2010 Macbook Pro running Snow Leopard and foolishly upgraded to Yosemite.  Is it possible to go back in time with Time Machine and reinstall Snow Leopard.  Then upgrade to Lion or Mavericks?  Any other ideas on how I can exit Yosemite?

    I have a mid 2010 Macbook Pro running Snow Leopard and foolishly upgraded to Yosemite. Now have numerous problems.  Is it possible to go back in time with Time Machine and reinstall Snow Leopard?  Then upgrade to Lion or Mavericks?  Any other ideas on how I can exit Yosemite?

    Once you get yourself back to Snow Leopard, if you still want to upgrade somewhat, I would suggest the following:
    1. Get an external hard drive that you can use for experiments with new OS versions. You could partition it into 2 or 3 partitions. You could then clone your existing Snow Leopard system to one partition using Carbon Copy Cloner (well worth $40) or SuperDuper ($25).
    2. Buy OS X Mountain Lion for $20, through the Apple online store (I don't think it's available through the App Store). Apple has decided to make it very difficult for anyone to get Mavericks unless they have already downloaded it.
    You will receive two e-mails from Apple, one containing a PDF with a redemption code, and one with the password you will need to unlock the PDF. Using the code, you will download Mountain Lion from the App Store, where it will appear among your Purchased items.
    After ML finishes downloading, its installer app will launch itself. When you see this launch screen, QUIT the install app immediately! Go to your applications folder, find the Install OS X Mountain Lion app, and copy it to a safe location outside of your Applications folder. Keeping one or more copies will allow you to reinstall without unnecessary aggravation if you later need or want to do that. At this point, you can re-launch the Installer in the Applications folder and let it run. You can install it on a clean partition on your external HD, or you can allow it to upgrade the Snow Leopard clone you created on your external drive, or you can do both. This should allow you to test how everything works for as long as you like.
    3. If you left yourself a free partition on your test drive, try a clean install of Yosemite and set everything up from scratch (do not migrate anything). This will allow you to see whether your problems with it were related to something in your Snow Leopard system.

  • HT201343 Can I upgrade my mid 2010 macbook pro to use airplay?

    Can I upgrade my mid 2010 macbook pro to use airplay?

    Unfortunately, no you can't.
    Just to be clear.  Your computer will support AirPlay it's just AirPlay Mirroring that requires newer hardware.
    Matt

  • Can I connect a blue ray player/burner to my mid 2010 MacBook Pro 17"?

    Can I connect a blue ray player/burner to my mid 2010 MacBook Pro 17"?

    Yes. Here are a couple:
    Blu-ray Player 2.8.2.1183
    iDeer Blu-ray Player 1.2.3.1183

Maybe you are looking for

  • How to Skip Print dialog window in smartforms

    Hi Experts, while printing the smartforms i dont want Print dialog window. I want as and when i pressed the print button it'll directly print with the specified printer. I tried with lot of option but it is not working for me . May be i missed some p

  • Centering a file in the browser vertically with CSS

    I remember there was an issue doing this with tables and I am wondering if this is also hard to to with CSS. I would like to center a flash file, both vertically and horizontally. I have it centered horizontally but not vertically. This is what I hav

  • E66 organizer

    I recently bought a Nokia E66 business phone. Fantastic phone, but I am quite disappointed with the organizer (calendar). I had a Nokia 6234. It had the capability that one could "move" a meeting to another date by using the month view of the calenda

  • Request Download for Master Data from ECC to CRM resulting in "Wait" Status in R3AR3

    Hi All, I have created request download in R3AR2 transaction to download master data for a particular Business Partner from ECC to CRM. But after I execute the request in R3AR4 transaction and check its status in R3AR3 transaction, it always states a

  • IconItemRenderer with alternating icon existence

    Hello, I have an IconItemRenderer in which some rows have icons (and decorators) and some do not. The ones that do not, align the labelDisplay as if they would and I wanted it to be left aligned. Is there something I'm missing, shouldn't a null icon