Can i replace media player with blu ray. dv7-4285dx win7 -64 bit. thanks.

i have an cd drive i would like to change to blu-ray? is this posible? can you give advice? thanks for your time jrblair.

Hi,
Do you really want to run Blu-ray content on a monitor that is only 1600 by 900?  Typical Blu-ray is 1920 by 1080.
HP DV9700, t9300, Nvidia 8600, 4GB, Crucial C300 128GB SSD
HP Photosmart Premium C309G, HP Photosmart 6520
HP Touchpad, HP Chromebook 11
Custom i7-4770k,Z-87, 8GB, Vertex 3 SSD, Samsung EVO SSD, Corsair HX650,GTX 760
Custom i7-4790k,Z-97, 16GB, Vertex 3 SSD, Plextor M.2 SSD, Samsung EVO SSD, Corsair HX650, GTX 660TI
Windows 7/8 UEFI/Legacy mode, MBR/GPT

Similar Messages

  • Replace dvd reader with blu ray in my brand new hp envy 17 leap motion se

    Hello everyone . For a month now I have this nice hp laptop which I installed an SSD .
    The only thing I do not like is the flexible keyboard but calling hp , they told me that it's okay for them and they can not do anything. I find it outrageous for a computer that cost me 1200 euro .
    Anyway I wanted to change the internal dvd player with a blue ray player. I link my laptop :
    http://h10025.www1.hp.com/ewfrf/wc/document?docname=c04010241&cc=it&dlc=it&lc=it&jumpid=reg_r1002_it...
    Can you tell me how should I do to replace it? Which player should I buy? I don't need to burn the blu ray but only read them well
    I write from Italy and I would serve you indicate to me that the precise pattern making examples that refer to stores like amazon or ebay, at least I understand better . Obviously, the Italian version then Amazon.it or ebay.it
    Then less important , I wanted to replace the two sticks of 4 gb ram with 2 of 8 to get to 16 gb. I checked and the model is a micron technology DDR3L . On the Internet I could not find the exact same model in version 8 gb then ask you which model is compatible with my laptop and if you could kindly always link me the article on amazon.it or ebay.it
    thank you very much

    Here's the jest I am going on the basis that your OD is a Sata interface and you will have to look for a Bluray Writer OD that is for Sata laptop drive not a Desktop drive. I give some examples but this is from the US sides and you can use it for references...this comes from eBay...
    Here's a link of my search
    http://www.ebay.com/sch/i.html?_sacat=0&_nkw=Sata+Bluray+burner&_sop=15
    Make sure you save your faceplate and swap it out with the one that came with the drive unless it doesn't have one but change the face plate to yours so it fits. You just have to make sure all the parts attached the original drive is put the same onto the replacement drive then you should be back in business. The Bluray burners from what I can tell are more expensive and the Panasonic Uj240 is a burner should you need one but there could be others but Panasonic Uj240 seems to one I find that I can tell are burners from the specs.
    I am a Volunteer to help others on here-not a HP employee.
    Replies aren't online 24/7 because of Time Zone differences.
    Remember in this Day and Age of Computing the Internet is Knowledge at your fingertips if you choose understand it. -2015-

  • Replacing Media Player with another player

    I've had a couple issues with my RoboHelp project's media
    files autostarting on some Macs. So, I tried replacing RoboHelps
    default Windows Media Player code with Quicktime code. But, in
    RoboHelp, when I leave the "HTML" disply and re-enter the "Design"
    display, RoboHelp deletes my Quicktime code and replaces it with
    its default Windows Media Code. Does anyone know how to over-ride
    this?
    -Greg

    Hello Greg -
    I don't use the RH find/replace function - I use stand-alone
    software and do the search/replace on the generated files (the
    files we publish). Look into your generated code for those
    references to Windows Media, copy the string as your "find" and
    write your desired string as the "replace" then do "replace all".
    There are a number of these programs available and have been
    mentioned many times in this forum. One popular tool is FAR from
    www.helpware.net but a search will bring up others.
    In our situation, I need to replace a couple generated files
    (files that are created by RH every time the project is generated).
    I took a gen'ed file then modified it and saved it to a separate
    project folder. After gen'ing a project we copy the saved/modified
    files into the generated project folder then publish.
    Regards,
    GEWB

  • How can I use Microsoft Media Player with my new iPod Nano?

    I do not like the iTunes player.  I want to use the Microsoft Media Player with my iPod Nano.  I dislike the iTunes player so much that if I don't get this resolved I will have to return the iPod Nano.

    Michelle,
    You can download media components for QuickTime which will enable you to play WMA files through QuickTime on your Mac:
    http://windows.microsoft.com/en-gb/windows/windows-media-components-quicktime
    Alternatively, Get the free VLC player for Mac, which will play almost all media types:
    http://vlc-media-player.en.softonic.com/mac
    If the interview requires Windows Media Player to be running to conduct the interview, then I fear you may be stuck, there is not a version of Windows Media Player for Mac - It is for Windows.  Your options in this case would be to borrow a Windows PC or install a valid copy of Windows on your MacBook under BootCamp.

  • Menu Problem with Blu Ray

    Can anyone help? I've created a project that contains 2 edited movies. I have added a main menu, and given both movies a main menu marker, and an end marker. Normally on DVD's this would send you back to the main menu when each of the films were completed, but I cannot get this to work with Blu Ray. Am I missing something here? What happens in this case is that the Disc starts with the menu, but if you pick the first item, the film will play OK, but instead of reverting back to the main menu, it carries on and shows the next .. and on completion, just terminates - does not go to the menu. The same if you select the second item. it just plays through and terminates. It seems that the End markers are being ignored. Has anyone got any ideas ??

    You can see how this product works by going to http://Muvipix.com and typing "DVD Architect" in the product search box. This will bring up a free 3-part Basic Training tutorial series where you can see the product demonstrated.
    You can also see more and learn about my book here.

  • I am in need of a new dvd player HD Blu-Ray and best buy is telling me that I need at least 10Mbps.

    Hi Niel, I am in need of a new dvd player HD Blu-Ray and best buy is telling me that I need at least 10Mbps. Where can I find this at my computer before I purchase this item.
    I hope you can help me. I have the 24 inch iMac.
    Denise
    <Subject Edited by Host>

    If you mean Ethernet, your computer already has it. If you're referring to something else, what is it?
    (125558)

  • Satellite L775-119 - Upgrade with blu-ray drive?

    Had my L775-119 for a few weeks, and it's going great, really pleased but am just wondering if it's possible, sometime in the future to upgrade the DVD RW Drive to a Blu ray re-writer?

    Hello
    Im not Satellite L775 owner but I think it should be possible because some L770/L775 models are delivered with blu-ray drive so generally speaking it seems that the notebook support such drives.
    But you can get an exact answer from an authorized service provider. The guys can order a compatible drive for you and install it if you are not familiar with notebook part exchange.
    Do you know how to contact an authorized service provider?

  • Sync Problem with Blu Ray

    I have a sync problem when using Premiere Pro CS5 to burn Blu Ray DVDs and wondered if anyone has had similar problems and has found a simple solution. 
    Equipment:  Panasonic HMC-150 (AVCHD), shot at 59.94 fps, 720.  MacPro with operating system up to date, quad core, 16 GB RAM, Nvidia Quadro 4000. PP CS5 also has all current updates downloaded.
    When the AVCHD files are imported, they tend to be out of sync by 8 to 22 frames.  I manually resync and edit.  Then burn a Blu Ray DVD using Encore and end up out of sync again.  I must be doing something wrong but can't figure it out.  At this point, the only solution I can think of is to try to figure out how far out of sync I am once the DVD is burned and offset the audio that amount before transcoding.
    Has anyone encountered this problem before?  Any suggestions? 
    Thanks. 

    I have done some more tests and have determined that the problem only exists with Blu-ray.  When I burn a non blu-ray dvd, video and audio remain in sync. I attempted to export to Final Cut Pro 7 using the export xml feature, but it doesn't work.  I brought the original footage into FCP and burned a portion of it to blu-ray using the Share feature and there was no sync problem.  So I guess my only alternative at this point is to re-edit the entire video in FCP.
    In Premiere Pro I've checked to make sure that both the camera and the intake were set for no drop frame and they were.  I've tried double checking the audio sync using the audio line out from the Mac rather than the firewire out to the Mackie Mixer, just in case there was a latency problem, which didn't seem logical and there wasn't any difference.  It can't be a problem with the blu-ray burner since it works in FCP7.  I'm running out of ideas of things I can tweak in Premiere, other than guessing just how far out of sync the program pushes the audio and then unlinking audio and pushing it the same number of frames the other direction before burning the blu-ray, but that will be hit and miss and it will start getting expensive throwing away blu-ray disks. 
    Any other ideas would be appreciated.  Thanks.  Jon

  • Does the Mac pro DVD player play Blu-ray discs?

    I suspect the answer is no, because the only DVD's that don't work in my player are blu-ray. But if someone can confirm this for me that would be great. If I need to download software to make my DVD player Blu-ray please direct me to the right site.
    S. Walker

    You can use a third-party BD drive to read and write data discs. However, there is no built-in software to play video BD's, even if you have a drive that can read them. I don't know whether there is now any third-party software that can play those discs; the last time I remember checking, there was not. It's technically (but not legally) possible to convert BD's to a format that can play natively on the Mac, but that subject can't be discussed within the terms of use of this site.
    The copy protection on BD's won't allow them to be played at full resolution on an external display without end-to-end hardware copy protection (HDCP) in the graphics subsystem.

  • Strobe media player with aspnet

    I want to use strobe media player with my aspnet application. Can I access it on server side. I want to read one video at one time and display using strobe media player. Also I want to control current position of the video from server side. Truly it feels like I want to use Strobe media player as Windows media player in visual studio. Can anyone has some idea..please.

    You can control SMP via JavaScript, so if your app can dynamically write values to the JavaScript used in the app, then you should be fine.

  • Can I replace InDesign CS6 with InDesign CS6 ME version?

    Can I replace InDesign CS6 with InDesign CS6 ME version? And does the ME version interface in English or Arabic?
    I have a translator who sends me InDesign files using the Sultan font, but when I open it, a lot of the font shows up as math symbols. I have the correct font installed, but I'm wondering if I need the additional features of the ME version of InDesign to make the type correct on my end.

    I don't believe my CS6 is from a Creative Cloud subscription. It was installed by my IT department, so I will ask them.
    When I receive the files from the translator, they send both an InDesign file and a PDF, so I can see it as they see it. However, the InDesign file looks like this:
    But the PDF file looks like this:
    They sent me the font file, so I'm assuming I have the right font and the issue is on my end. Or perhaps not?

  • IMac with Blu-Ray or HD-DVD drive. When?

    Is there any info about when iMacs with Blu-Ray or HD-DVD drive will be available?

    Apple sits officially in the Blu-Ray camp so HD-DVD is less likely. 
    A slot-loading drive exists but only Apple know when and if they choose to use it in the iMac.
    At this time even the Mac Pro doesn't have it as an option (unless you install yourself for $700, although that does inc Toast Ti).
    mrtotes

  • How can i make audio player with osmf??

    i want to know how can i make audio player with osmf and flex4.5 ?

    Thanks again...I suppose I'd just like it louder in case the radio is on when the directions are given. The difference between the iPhone & Nokia is like night & day!
    BTW, do you know if the Maps program is using data from my cell phone plan as we drive? Or are the corresponding maps downloaded into the phone once for the trip?
    Thanks again!!

  • Macs or mac mini work with blu ray external drives even XL DISC CAPACITIES

    macs or mac mini work with blu ray external drives (BURNERS) even XL DISC CAPACITIES like 128GB?

    https://discussions.apple.com/docs/DOC-2881

  • Can we replace OTR text with Images?

    Hi All,
    I just wanted to know can we replace OTR text with Images?
    or
    Can we define an image as an OTR text? so that it can be placed in the page where OTR text is used.
    regards...
    Ravi

    Hi Ravi,
    it is possible to replace an OTR Text with an image.
    You first have to define the Link in the OTR Text where your image is located. This can be everywhere in the Internet or better on a secured intranet server which everyone can reach easily without permission problems. Maybe in the DMZ.
    You can even link it into the MIME Repository of your SAP System as well.
    Then you have to put that OTR Text into a
    <htmlb:textview> Tag and ensure that the switch
    " encode = "TRUE" is enabled.
    Well thats all.
    Keep in mind that the a different language, set in the Internet Explorer or other viewing instances, disables the link if it not "translated" into that language.
    This can also be an advantage if you got multilingual fixed pictures with drawn text in it.
    I suggest you put all your links ( with a Value Field and at least a name field) into a seperate table into the repository for easy maintaining.
    Greetings,
    Dominik
    Edited by: Dominik Lemke on Dec 19, 2007 12:02 PM

Maybe you are looking for