Can I restore settings after upgrade?

I just upgraged to Mac 10.4. I had an awsome library with all the songs rated and varied playlists. How do I restore my settings on the new system. The old system has been archived so i do have access to the old preference files.

Hi,
Ratings, playlists, playcounts, etc. are stored in a file called "iTunes Library" in (home)/Music/iTunes (not in the preferences).
Have you restored your music files to your comptuer already? If so, now bring the library file over from your archive and put it in the same place.
Let us know how it goes or if you have any other questions.
Sara.

Similar Messages

HT201250 How to restore all my mac book pro (mid 2009) files, data, Mavericks and settings after upgrading HD (250 to 500GB) from my Time Capsule?

Hi everyone!
Please, I need a big help from you!
Do you know how to restore from Time Capsule all my mac book pro (mid 2009) files, data, Mavericks and settings after upgrading HD (250 to 500GB)?
Thank you very much!
Best regards,
Marcio

Recover your entire system
See 14.
Time Machine FAQ

I can't use firefox after upgrading to 4.0. I get the message I have to restart my computer for upgrading, but ik doesn't start. I get the message over and over

I can't open firefox after upgrading to 4.0
I get the message over and over again that i have to restart my computer for upgrading to firefox.
I tried new installation. But i got problems on all my accounts

Start your '''Computer''' in safe mode. Then start Firefox. Try '''Safe''' web sites.
Starting The Computer In Safe Mode;
If running, turn your computer off.
Remove any disks and thumb drives that are in your hard drives or ports.
Now start your computer but also;
'''Windows; '''Press the <F8> key repeatedly.
'''Mac: '''Hold down the Shift key.
'''Linux; '''Using the command line, Linux/Unix computers can be booted
into various run levels that determine which resources are loaded.
For example, "runlevel 1" is typically the equivalent to Windows and
Mac safe modes.
* Source; '''[http://encyclopedia2.thefreedictionary.com/Linux+Safe+Mode Safe Mode; Free Online Encyclopedia]'''
When the '''Boot''' menu is displayed, release the key you were pressing.
You must now choose what mode to use. The most used are;
* Safe Mode; The computer runs with only a minimum set of programs.
* Safe Mode '''With '''Networking; Same as above, but with internet access.

Can't launch color after upgrading to OS 10.5

I can't launch color after upgrading to OS 10.5. The message shows " Unable to initialize OpenGL. Make sure Video Desktop is disable." Can anyone help please?

Click here and follow the instructions.
(46092)

Can´t open LR after upgrade to 5.3 without entering a licens key

Can´t open LR after upgrade to 5.3 without entering a licens key

I have seen comments from someone who indicated that every time they started Lightroom they were prompted for the serial number, even though they had already entered it. Is this your situation? I can't remember what the solution is, but I have seen that problem mentioned in the past.

Can't open Pages after upgrading to snow leopard on 10.6.8

Can't open Pages after upgrading to snow leopard on 10.6.8

Has Spotlight finished its indexing? Check in the upper right. If you get just the search field, it has, if it says its indexing, you have to wait before you can use anything.

I have an Epson Perfection V100 scanner and can no longer scan after upgrading to Mountain Lion and Creative Suite 5.5. Any suggestions?

I have an Epson Perfection V100 scanner and can no longer scan after upgrading to Mountain Lion and Creative Suite 5.5. Any suggestions?

Check the Epson web site for updates to drivers and Epson scan software.

WiSM can't function normally after upgrading from vesion 6.0.182 to 7.0.220.

I have a WiSM installed in WS-6504E, vesion 6.0.182. It can't function normally after upgrading to version7.0.220.
When it was unstable, I found three strange condition
1. A lot of log looks like this
*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-FILE_OPEN_FAILED: osapi_file.c:370 Failed to open the file : /proc/1059/stat.(erno 24)
*osapiReaper: Mar 10 14:53:39.282: %OSAPI-3-TASK_GETTIME_FAILED: osapi_task.c:3431 Failed to retrieve statistics (/proc/<pid>/stats) for task 'fmcHsTask'
2. Internal Temperature was showed "sensor failed"
3. CPU User load is Zero
Anybody can tell me what wrong with the wireless controller ?

Could be a hardware failure.

3014 error i can't restore ipad after firmware update attempt

3014 error i can't restore ipad after firmware update attempt

See this thread with the same question.
https://discussions.apple.com/thread/5045573?tstart=0

I can't load modules after upgrade

I can't load modules after upgrade xfree 4.4.0-2, gcc 3.4.0-1, perl 5.8.4-1 and kernel 2.6.5-3.I don't have even access to the internet from Arch.System says that modules have invalid version.
What can I do now?

You were right robot5x. After command lilo I have got modules loaded properly.Thanks.

HT3669 I have an Epson Perfection V100 and can no longer scan after upgrading to Mountain Lion and Creative Suite 5.5. Any suggestions?

I have an Epson Perfection V100 and can no longer scan after upgrading to Mountain Lion and Creative Suite 5.5. Any suggestions?

Check the Epson web site for updates to drivers and Epson scan software.

Can not print print after upgrade to Mac OS 10.8 Mountain Lion

Hi all,
I just upgrade Macbook air to Mountain Lion, but after upgrade it can not print due to "hold for Authentication" error. Mac asking for User name and password, I tried to enter my mac User name and password but can not help.
I change to other type of printer but still same problem
I also try to reinstall Mac Mountain Lion from start(not update from Lion) but still face off same problem.
Is there anybody can help me for this? I was in big trouble for this problem for over the week.
Thank you so much

hi . I had the simalar problems of my HP b209a-m printer not being seen on my wireless network> I found this post on HP Discussion Board and it worked!
1. On the printer navigate to the Wireless or Network menu.
2. Select Restore Defaults.
3. On your computer look for a wireless network named 'hpsetup' and connect to it.
4. Print a Wireless Network Test from the front of the printer to see its IP address. (on my b209a-m Printer the IP info was found by pressing the Wireless Icon)
5. Type the IP address into the address bar of a web browser to see the printer's internal settings.
6. Click on the Network tab and look for the Wireless Setup Wizard and run it.
7. The Passphrase is the password you use on your wireless connection.
8. Now change the network name on your computer back to your wireless network.
The printer will now be connected to your network. Connect the computer back to the network and re-add the printer from System Preferences.
Hope this works--- it did for me.
Jim

Cannot restore settings after updating to iOS 5

I have upgraded successfully to iOS 5, well almost, because just after the upgrade finished, I wen't through the settings (language, country, WI-FI) and was then given a choice to set as a new device or restore from backup. Since my backup is on my computer I chose restore from iTunes.
But restoring fails, and this happens for both my iPhone 4 and iPad 2. I've been given a number of errors (-19 or -50) and sometimes it just says "iTunes cannot restore iPad because the backup session failed".
This happens on both my iPad and iPhone no matter which backup file I choose.
With the iPhone I've tried to put it in recovery mode and reset to factory settings, but I still can't restore it.
Anyone else with this problem, and does anyone know what to do?

READ THIS!!!!!
For anybody having these issues here is what I did.
First of all, BACKUP your original backup, yes a backup of a backup. First of all make hidden files visible, at your explorer go to tools>folderoptions>view and show hidden files and folders. If you cant find the tools at your window press alt and a toolbar will appear. The file is located in C/users/YOURACCOUNT/appdata/roaming/applecomputer/mobilesync/backup.
Again this is just a precaution.
Now if you some sort of anitvirus program, ESPECIALLY if it is AVAST. Turn it off! For some reason it is conflicting with restoring with the backup.
Restart Itunes and plugin your iphone, it will probably still come up with the (-50) error. Ignore this! Now right click your iphone under devices at the left side of itunes. Then choose then do restore from backup and wait. Hopefully your Iphone screen will say restore in progress!
Now I just hope this helps someone as I was freaking out because I was updating my bros iphone. And he had a lot of saves and photos etc.
If you have ANY questions please ask as I know how frustrating this error is.

I5 can not connect wifi after upgraded to IOS 6.1.2

i5 can not connect to my laptop share-wifi after upgraded to IOS 6.1.2, while it's ok before upgrade. How can I solve it?

FIXED!!!!
I have iPhone 4s running 6.1.2 Everything worked great before the lovely update. My wifi did the same thing that everyone else's seems to be doing. It would not recognize my home router.
Evidently, in the update, Apple changed how the "Ask to Join Networks" button operates. Previously, I didn't have to have the button toggled to on, my phone would just automatically lock onto my router. I have fought and fought with this update. I have done several "network settings resets". I have even restored my phone twice. I have tried every crackpot, and not so crackpot, suggestion on these forums and NOTHING has worked. I could go to settings and connect to the router each time I used the phone, but it would only stay connected for a few minutes.
Today, I toggled the "Ask to Join Networks" button to "on", then opened Safari. My phone then asked if I wanted to join the network, I responded with "join". My phone has been on wifi all day! I left home and came back several hours later, and FINALLY... my phone locks on automatically.
Go to settings>, Wi-Fi>, toggle "Ask to Join Networks" button to "on". Then click on your router/network in the list.
I realize that everyone's problems are not the exact problems I had, but maybe this will help some of you having problems.
Good Luck!

Can't restore iPod after seeing the "Exclamation point folder icon"

My iPod showed me the "Exclamation point folder icon" out of the blue... i tried resetting, restoring (upgraded to 7.1 in the process) but when i connect the ipod to my computer it still shows me the icon, then the Apple sign, then "Do not disconnect" (while charging) and then the ipod itself starts clicking...
any help would be GREATLY appreciated!! very furstrated over here...

Hello,
If a sad iPod icon or an exclamation point and folder icon appears on your iPod’s screen, or with sounds of clicking or HD whirring, it is usually the sign of a hard drive problem and you have the power to do something about it now. Your silver bullet of resolving your iPod issue – is to restore your iPod to factory settings.
http://docs.info.apple.com/article.html?artnum=60983
If you're having trouble, try these steps at different levels one at a time until the issue is resolved. These steps will often whip your iPod back into shape.
Make sure you do all the following “TRYs”
A. Try to wait 30 minutes while iPod is charging.
B. Try another FireWire or USB through Dock Connector cable.
C. Try another FireWire or USB port on your computer .
D. Try to disconnect all devices from your computer's FireWire and USB ports.
E. Try to download and install the latest version of iPod software and iTunes
http://www.apple.com/itunes/download/
For old and other versions of iPod updater for window you can get here
http://www.ipodwizard.net/showthread.php?t=7369
F. Try these five steps (known as the five Rs) and it would conquer most iPod issues.
http://www.apple.com/support/ipod/five_rs/
G. Try to put the iPod into Disk Mode if it fails to appear on the desktop
http://docs.info.apple.com/article.html?artnum=93651
If none of these steps address the issue, you may need to go to Intermediate level listed below in logical order. Check from the top of the lists to see if that is what keeping iPod from appearing on your computer in order for doing the Restore.
Intermediate Level
A. Try to connect your iPod with another computer with the iPod updater pre-installed.
B. Still can’t see your iPod, put it in Disk Mode and connect with a computer, instead of doing a Restore on iPod Updater. Go and format the iPod instead.
For Mac computer
1. Open the disk utility, hope your iPod appears there (left hand side), highlight it
2. Go to Tab “Partition”, click either “Delete” or “Partition”, if fails, skip this step and go to 3
3. Go to Tab “Erase” , choose Volume Format as “MAC OS Extended (Journaled), and click Erase, again if fails, skip it and go to 4
4. Same as step 3, but open the “Security Options....” and choose “Zero Out Data” before click Erase. It will take 1 to 2 hours to complete.
5. Eject your iPod and do a Reset
6. Open the iTunes 7 and click “Restore”
For Window computer
Go to folder “My Computer”
Hope you can see your iPod there and right click on the iPod
Choose “Format”. Ensure the settings are at “Default” and that “Quick Format” is not checked
Now select “Format”
Eject your iPod and do a Reset
Open the iTunes 7 and click “Restore”
In case you do not manage to do a “Format” on a window computer, try to use some 3rd party disk utility software, e.g.“HP USB Disk Storage Format Tool”.
http://discussions.apple.com/thread.jspa?threadID=501330&tstart=0
C. Windows users having trouble with their iPods should locate a Mac user. In many cases when an iPod won't show up on a PC that it will show up on the Mac. Then it can be restored. When the PC user returns to his computer the iPod will be recognized by the PC, reformatted for the PC, and usable again. By the way, it works in reverse too. A Mac user often can get his iPod back by connecting it to a PC and restoring it.
Tips
a. It does not matter whether the format is completed or not, the key is to erase (or partly) the corrupted firmware files on the Hard Drive of the iPod. After that, when the iPod re-connected with a computer, it will be recognized as an fresh external hard drive, it will show up on the iTunes 7.
b. It is not a difficult issue for a Mac user to find a window base computer, for a PC user, if they can’t find any Mac user, they can go to a nearest Apple Shop for a favor.
c. You may need to switch around the PC and Mac, try to do several attempts between “Format” and “Restore”
http://discussions.apple.com/thread.jspa?messageID=2364921&#2364921
Advance Level
A. Diagnostic mode solution
If you have tried trouble shooting your iPod to no avail after all the steps above, chances are your iPod has a hardware problem. The iPod's built-in Diagnostic Mode is a quick and easy way to determine if you have a "bad" iPod.
You need to restart your iPod before putting it into Diagnostic Mode. Check that your hold switch is off by sliding the switch away from the headphone jack. Toggle it on and off to be safe.
Press and hold the following combination of buttons simultaneously for approximately 10 seconds to reset the iPod.
iPod 1G to 3G: "Menu" and "Play/Pause"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Menu" and "Select"
The Apple logo will appear and you should feel the hard drive spinning up. Press and hold the following sequence of buttons:
iPod 1G to 3G: "REW", "FFW" and "Select"
iPod 4G+ (includes Photo, Nano, Video, and Mini): "Back" and "Select"
You will hear an audible chirp sound (3G models and higher) and the Apple logo should appear backwards. You are now in Diagnostic Mode. Navigate the list of tests using "REW" and "FFW". The scroll wheel will not function while in diagnostic mode. For further details on Diagnostic mode can be found at http://www.methodshop.com/mp3/ipodsupport/diagnosticmode/
Try to do the 5in1, HDD R/W and HDD scan tests. Some successful cases have been reported after the running the few tests under the Diagnostic mode. In case it does not work in your case, and the scan tests reports show some errors then it proves your iPod has a hardware problem and it needs a repairing service.
B. Format your iPod with a start disk
I have not tried this solution myself, I heard that there were few successful cases that the users managed to get their iPod (you must put your iPod in disk mode before connecting with a computer) mounted by the computer, which was booted by a system startup disk. For Mac, you can use the Disk Utility (on the Tiger OS system disk), for PC user, you can use the window OS system disk. Try to find a way to reformat your iPod, again it does not matter which format (FAT32, NTFS or HFS+) you choose, the key is to erase the corrupted system files on the iPod. Then eject your iPod and do a Reset to switch out from Disk Mode. Reboot your computer at the normal way, connect your iPod back with it, open the iPod updater, and hopefully your iPod will appear there for the Restore.
If none of these steps address the issue, your iPod may need to be repaired.
Consider setting up a mail-in repair for your iPod http://depot.info.apple.com/ipod/
Or visit your local Apple Retail Store http://www.apple.com/retail/
In case your iPod is no longer covered by the warranty and you want to find a second repairing company, you can try iPodResQ at your own risk
http://www.ipodresq.com/index.php
Just in case that you are at the following situation
Your iPod warranty is expired
You don’t want to pay any service charges
You are prepared to buy a new one
You can’t accept the re-sell value of your broken iPod
Rather than leave your iPod as paper-weight or throw it away.
You can try the following, but again, only do it as your last resort and at your own risk.
Warning !!!! – It may or may not manage to solve your problem, and with a risk that you may further damage your iPod, which end up as an expensive paper weight or you need to pay more higher repairing cost. Therefore, please re-consider again whether you want to try the next level
Last Resort Level
1. . Disconnecting the Hard Drive and battery inside the iPod – Warning !! Your iPod warranty will be waived once you open the iPod.
In Hong Kong there are some electronic shops offering an iPod service for Sad iPod, the first thing they do is to open up the iPod’s case and disconnecting the battery and the Hard Drive from the main board of the iPod. Wait for 5-10 minutes and reconnecting them back. The reason behind which I can think of is to do a fully reset of a processor of the iPod. In case you want do it itself and you believe that you are good on fixing the electronics devices and have experience to deal with small bits of electronic parts, then you can read the following of how to open the iPod case for battery and HDD replacement (with Quicktimes)
http://eshop.macsales.com/tech_center/index.cfm?page=Video/directory.html
2.Press the reset button on the Hard Drive inside the iPod – Suggestion from Kill8joy
http://discussions.apple.com/thread.jspa?messageID=2438774#2438774
Have I tried these myself? No, I am afraid to do it myself as I am squeamish about tinkering inside electronic devices, I have few experiences that either I broke the parts (which are normally tiny or fragile) or failed to put the parts back to the main case. Therefore, I agree with suggestion to have it fixed by a Pro.
2. Do a search on Google and some topics on this discussion forum about “Sad iPod”
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=3597173#3597173
Exclamation point and folder and nothing else
http://discussions.apple.com/thread.jspa?messageID=2831962#2831962
What should I do with my iPod? Send it or keep it?
http://discussions.apple.com/thread.jspa?threadID=469080&tstart=0
Strange error on iPod (probably death)
http://discussions.apple.com/thread.jspa?threadID=435160&start=0&tstart=0
Sad Face on iPod for no apparent reason
http://discussions.apple.com/thread.jspa?threadID=336342&start=0&tstart=0
Meeting the Sad iPod icon
http://askpang.typepad.com/relevanthistory/2004/11/meeting_thesad.html#comment-10519524
Sad faced iPod, but my computer won’t recognize it?
http://discussions.apple.com/thread.jspa?messageID=2236095#2236095
iPod Photo: unhappy icon + warranty question
http://discussions.apple.com/thread.jspa?messageID=2233746#2233746
4th Gen iPod Users - are we all having the same problem?
http://discussions.apple.com/message.jspa?messageID=2235623#2235623
Low Battery, and clicking sounds
http://discussions.apple.com/thread.jspa?messageID=2237714#2237714
Sad faced iPod, but my computer won’t recognize it
http://discussions.apple.com/thread.jspa?messageID=2242018#2242018
Sad iPod solution
http://discussions.apple.com/thread.jspa?threadID=412033&tstart=0
Re: try to restore ipod and it says "can't mount ipod"
http://discussions.apple.com/thread.jspa?threadID=443659&tstart=30
iPod making clicking noise and is frozen
http://discussions.apple.com/thread.jspa?messageID=2420150#2420150
Cant put it into disk mode
http://discussions.apple.com/thread.jspa?messageID=3786084#3786084
I think my iPod just died its final death
http://discussions.apple.com/thread.jspa?messageID=3813051
Apple logo & monochrome battery stay
http://discussions.apple.com/thread.jspa?messageID=3827167#3827167
I am not suggesting that you should follow as well, but just read them as your reference. You are the person to make the call.
Finally, I read a fair comments from dwb, regarding of slapping the back of the iPod multiple times
Quote “This has been discussed numerous times as a 'fix'. It does work, at least for a while. In fact I remember using the same basic trick to revive Seagate and Quantam drives back in the mid to late 1980's. Why these tiny hard drives go bad I don't know - could be the actuator gets stuck in place or misaligned. Could be the platter gets stuck or the motor gets stuck. 'Stiction' was a problem for drives back in the 80's. Unfortunately the fix can cause damage to the platter so we temporarily fix one problem by creating another. But I know of two instances where a little slap onto the table revived the iPods and they are still worked a year or more later.”UnQuote

Can I restore settings after upgrade?

Similar Messages

Maybe you are looking for