Can I run a 2560x1440 monitor with HP Pro 3381 MT

I have a Desktop 27 inch which has model "HP Pro 3381 MT" and monitor`s resolution is 1366*768 .
My OS is IOS hackingtosh.
I want to run with my PC as IMAC with 2560*1440 resolution.
Can I solve this problem?

Hi,
It does nit say much from the following information:
http://browser.primatelabs.com/geekbench2/2432849
Looks like it is an old machine it may not be able to drive a high resolution monitor. And you need a monitor first.
Regards.
BH
**Click the KUDOS thumb up on the left to say 'Thanks'**
Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

Similar Messages

Can I run a 2560x1440 monitor with the envy dv7t 7300

Can I run a 27" WQHD 2560x1440 ips monitor at full res with my Envy DV7t 7300. I7 quad 2.6 GHz, GT650m 2gb ?
Thanks, Cesar

Hi linacjsdad,
Thank you for your query, I will do my best to help.
If you connect the monitor with a HDMI connection it will support the highest resolution.
Your HD 7670M DDR# graphic card will support resolutions of 2560x1600 which is higher then the monitor, therefore you should not have an issue. Specifications of the AMD Radeon HD 7670M DDR3 GPU
HP ENVY dv7 Notebook PC Maintenance and Service Guide Please note chapter 2 pages 3 and 4.
Sparkles1
I work on behalf of HP
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom right to say “Thanks” for helping!

M6 pavilion 1006tx, Can I run a 2560x1440 monitor

Can I run a dell u2713h 27" WQHD 2560x1440 ips monitor at full res with my M6 pavilion 1006tx. I7 3612qm 2.1 GHz, AMD HD7670M DDR3?
M6 pavilion 1006tx HDMI can support 2560 x 1440?
Monitor- Dell u2713h
M6 pavilion 1006tx
i7 3612qm 2.1ghz
amd hd7670m ddr3 2gb
HDIM cable connet
thanks!
This question was solved.
View Solution.

Hi @TONYOOI ,
Thank you for visiting the HP Support Forums and Welcome. I have looked into your issue about your HP Pavilion m6-1006tx Entertainment Notebook PC and running a monitor with a HDMI cable. Here is a document on changing the HDMI display settings to fit your Screen and to check your settings and to troubleshoot specific problems.
Hope this helps.
Thanks.
Please click “Accept as Solution ” if you feel my post solved your issue, it will help others find the solution.
Click the “Kudos, Thumbs Up" on the bottom to say “Thanks” for helping!

Can I run two 2560x1440 monitors (dual link DVI) on a new Mac Pro?

I have two Monoprice Zero-G IPS monitors, which can run at resolutions of 2560x1440 using a dual-link DVI adapter. This is what I am currently using on my old 2008 Mac Pro.
If i get a new model Mac Pro, could I continue this arrangement at the max resolution by using two Thunderbolt/Minidisplay port to Dual link DVI adapters (and, I assume, using two of the USB ports as I do now)?
Frankly, I dont need the power of a new Mac Pro but my old one is long in the tooth. I'd get a retina Macbook and use it as my desktop, but I cant think of any way to run both monitors at full resolution on the Macbook Pro. I dont want to run them at HDMI resolution.
Thanks in advance!

Adapters go from $9 to $54, the latter having heat-sink which is not needed in an open cMP.
Some support both as in either or but not two at the same time, SATA interface on the PCIe afapter, or an M.2 type
While other PCIe "solutions" exist they are not OS independent or machine, the XP941 suffers from none of those concerns as it is bootable in all Mac Pro 1,1 thru 5,1, and is the only one for 200-7 models (and 2008 are iffy) so you can 'take it with you' if you move to a new cMP.
Old controller, you need two SSDs in RAID0 to get 900MB/sec writes.
Does not appear to be any of the real issues of PCIe slot and bus master, outside of you would exclude the 1x slot in the 2006 of course!
The hardest part? getting these tiny M.2 blades, which are ~ 1" x 3.25" and have a tiny screw, on the PCIe adapter.
250GB SSD today are ~$120 + many do want SATA III PCIe (to get 550MB/sec and allow continued use of 4 x SATA II drive bays) runs ~$80-299. In some cases you then need a 2nd SSD. So if you want speed (vs size) then $240 + $100 and the $300 for XP941 256GB isn't bad.
Finally, look for an Apple blade on ebay if running Yosemite - they vary, some are 2x (slow) M.2s and you want 4x but any are probably 700MB/sec and cost $400-700. No need with Apple part to worry about TRIM.
Comparing 128GB SATA II $83 + $15 adapter vs PCIe XP941 128GB $140 + $24 is a 'toss-up' in cost but not performance, and one frees up drive bay and uses PCIe slot. (Generally 250GB are faster and better, the 128GB use to have 135MB/sec writes and $40 extras for 550MB and double storage makes sense, you never want an SSD to get down to 20% free, and you want to have 11% set aside for over-provisioning).
So in a way you can get 1000MB/sec like nMP for $175-300 in any Mac Pro, and new faster blades are on the horizon offering 1400MB/sec.
Kind of amazing, that M.2 support is in that old EFI all along waiting

Any advice about running a 24" monitor with Macbook Pro?

In a far city, 3,000 miles from my tower and Apple Cinema screens. I have to edit a film from a little MacBook Pro laptop (2.16 GHz Intel Core Duo, max 2 GB 667 MHz DDR2 SDRAM).
I borrowed a 24" Acer, plugged it in. Seems to look okay for editing. But panning and any movement is generating mild breakup, like a thin slash through the image. I'm wondering if there is some way I can set up the laptop to more efficiently drive the external monitor?
So far all I've done is plugged it in, and set it up as the playback screen for Final Cut Pro.
Any suggestions would be most appreciated...
Ben

According to the Apple spec sheet, your external monitor port should support up to 2560 by 1600 pixels on a MacBook Pro 2,2, which I think you have. You could try setting the external to smaller res numbers and see if that helps.
My 22" LCD monitor has a maximum res of 1680x1050 and I suspect the native res on your 24" external is less than the 2560x1600 that the MBP is supposed to support.
Are you in spanning mode or mirrored mode? Might try both and see if one works better.

Can a macbook pro 13" retina (mid-2014) run 2 external monitors with 2560x1440 resolution?

Can a macbook pro 13" retina (mid-2014) run 2 external monitors with 2560x1440 resolution? If not what if I turn off the macbook internal display? I

Yes.
http://support.apple.com/en-us/HT204154
Ciao.

How do i run an external monitor with my macbook and change settings so that when i close the lid the signal to the monitor is not lost and i can continue using the mac with a mouse and a wireless keyboard?

How do i run an external monitor with my macbook and change settings so that when i close the lid the signal to the monitor is not lost and i can continue using the mac with a mouse and a wireless keyboard?

No, nothing will prevent the computer from going to sleep when you close its display except third-party hacks that are designed to do exactly that. I strongly advise against using any of those, as they may interfere with successful entry into clamshell mode (and they carry other downside risks as well). Just wait until the computer is asleep (with its sleep light pulsing), then press any key on the keyboard. It sounds as though your setup is working as it's designed to do.

I have a MB Pro that is running Lion; I also have two external DVI monitors and a DVI splitter in hopes that I could run the two monitors with my MB Pro. This actually works fine, but I am unable to "extend" the desktop. Any insights?

I have a MB Pro that is running Lion; I also have two external DVI monitors and a DVI splitter in hopes that I could run the two monitors with my MB Pro. This actually works fine, but I am unable to "extend" the desktop. Any insights?

You cannot have a extended desktop using a splitter. All that does is mirror the pair attached to the splitter.
You can do this however using a Matrox DualHead2Go.
Other solution would be to attach one monitor to your video out as you do the splitter and attach the other via USB (assuming the adapter supports the monitor's resolution).
Newer Technology USB to DVI / HDMI / VGA HD Video Display Adapter

Can I run 2 different domains with same name but on 2 different machines?

I am trying to setup 2 domains with same name (sharedcds1) on 2 different machines (Machine1 and Machine2).
          When I start the weblogic managed server 1 (sharedcds1managedserver1) on Machine2, it throws an error saying it has some conflicts with the managed server 1 running on Machine1. How did the managed server of one machine know about the other server. Can I run 2 different domains with same name but on 2 different machines?
          Here is the error in the log -
          <Jun 14, 2005 10:53:29 AM EDT> <Error> <Cluster> <BEA-000123> <Conflict start: You tried to bind an
          object under the name weblogic.transaction.coordinators.sharedcds1managedserver1 in the JNDI tree.
          The object from 4596206652609838848S:130.170.61.153:[9505,9505,-1,-1,9505,-1,-1,0,0]:sharedcds1:s
          haredcds1managedserver1 is non-clusterable, and you have tried to bind more than once from two or m
          ore servers. Such objects can only be deployed from one server.>
          <Jun 14, 2005 10:53:29 AM EDT> <Error> <Cluster> <BEA-000123> <Conflict start: You tried to bind an
          object under the name weblogic.transaction.coordinators.sharedcds1managedserver1 in the JNDI tree.
          The object from 8842351474821025197S:130.170.61.154:[9505,9505,-1,-1,9505,-1,-1,0,0]:sharedcds1:s
          haredcds1managedserver1 is non-clusterable, and you have tried to bind more than once from two or m
          ore servers. Such objects can only be deployed from one server.>
          Thanks
          Satish

Yes you can. Make sure that domains configured to use different multicast address. WLS uses multicast for communications between nodes in domain.
          although your configuration will work, you could have troubles if you going to execute inter-domain calls between domains/servers with the same names.

How can I run a vga monitor and projector together on my Mac Pro 15"??

How can I run a vga monitor and projector together on my Mac Pro OSX 15"?

You can upgrade to Snow Leopard, Lion or Mountain Lion (coming next month), but you need Snow Leopard to upgrade to Lion or Mountain Lion. Check this web to know how to add memory to your computer and the memory that it supports (probably, 3 GB).

How can I run a vi developed with 7 Express?

How can I run a vi developed with LabView 7 Express on another machine ? Do runtime versions exist ?

Apparently, you want to run it on a machine that does not have LabVIEW installed.
To make a standalone executable of your LabVIEW program, you need to have the Application builder (included in LabVIEW professional and higher, avaliable as an add-on for base and full).
To run the application, the target system need to have the LabVIEW 7.0 runtime installed (available as a free download).
There is also the LabVIEW Player. In this case you need to digitally sign your VIs and there are a few limitations. It is meant for for sharing code ideas and is not a viable substitute for the appl
ication builder.
Of course you could also get a second copy of LabVIEW.
Some other options that would work in a very narrow set of situations: Read your LabVIEW license agreement. Under certain conditions you are allowed to install a second copy of LabVIEW on your home computer. If this is for personal educational use only and you qualify, you could also buy the LabVIEW student edition.
LabVIEW Champion . Do more with less code and in less time .

I can't use my Philips monitor with Mac mini

I can't use my Philips monitor with Mac mini, I am using a HDMI to VGA cable to connect them. But no signal on my Philips monitor.
My Mac mini is in a good condition, it can connect with my HDTV, the BENQ monitor at my office, but I can't make it connect with my Philips monitor.
I dun know what happen.
Please help!
Thanks!

The two are incompatible, HDMI is a digital signal and VGA is an analog signal. You need a monitor with a HDMI port or a DVI-I port, these are both digital signals. DVI-I gives the best output.

Can I use a 2nd monitor with my HP TouchSmart 310-1020?

can I use a 2nd monitor with my HP TouchSmart 310-1020?

http://h30434.www3.hp.com/t5/TouchSmart-PC/how-to-hook-up-a-second-monitor-on-an-hp-touchsmart-compu...
Kate has some great information in answer to this question.
Take a look.
GeorgeFN
GeorgeFN
I work on behalf of HP.

Hello, I have a MacBook pro retina 13" early 2013, and i am not sure if I can use a 4k2k display Monitor with my Macbook, please help!

Hello, I have a MacBook pro retina 13" early 2013, 2,6 GHz Intel Core i5 and Intel HD Graphics 4000 1024MB,
and i am not sure if I can use a 4k2k display Monitor with my Macbook, please help!

Hello, Righten.
Thank you for visiting Apple Support Communities.
I understand that you want to know if your MacBook Pro will support a 4k display. Here is an article that will answer your question.
Using 4K displays and Ultra HD TVs with your Mac
Cheers,
Jason H.

How can i run Lightroom 3.6 with RAW files from Canon 650D?

How can i run Lightroom 3.6 with RAW files from Canon 650D?

Download the newest DNG converter from Adobe, convert your RAW photos to DNG, and then Import into Lightroom.

Can I run a 2560x1440 monitor with HP Pro 3381 MT

Similar Messages

Maybe you are looking for