"can i set up a Actiontec GT704WGB Gateway and a Actiontec GT704WG Gateway behind as a bridge ?

i want more wireless power in my other room..and i was thinking about buying a bridge .then i though why not see if its possible too set up the704wg behind the the 704wgb as a wireless bridge. before i go out and blow 50 to 100 bucks... alienware p2 750i .os vista ultimate. core intel q9550 duel quad core @ 2.83. if this helps im new at this so plz bare with me .Thanks Kirk 

The ActionTec GT704WGB and the GT704WG don't support WDS or Client Bridge mode via Wireless, so they will not act as a repeater. They can act as access points if you run an Ethernet cable to them however. They just need to be set up to operate as such.
So for this issue, unless relocating the router or antennas improves signal quality you are most likely looking at running CAT5/CAT6 cabling, using MoCa or Powerline or setting up another access point nearby. I would suggest against repeating as anything going through the repeater has half the usable bandwidth, which makes a difference if you send a lot of data back and fouth or are on anything higher than 7.1Mbps for DSL service.
========
The first to bring me 1Gbps Fiber for $30/m wins!

Similar Messages

  • How can I set my WebI filters to Null and not Null

    Folks,
    I have created a report in WebI and now I am to set up some filters as Null and some Not Null.
    How can I set my WebI filters to Null and not Null?
    Regards,
    Bashir Awan

    Hi,
    As you said you could do it at the report level and also at the universe level.
    One more way is to create the filters in the universe levele and add them in thequery filter.
    Ex: in the filter you need to write :
    Column1 is null and and column 2 is not null etc.
    Hope this will help.
    If this did't  solve your problem then please explain it in detail.
    Cheers,
    Ravichandra K

  • HT204053 Hi, how can I set up icloud for my ipad and iphone5? I missed tout he initial setup step and now want to have both the devices under icloud. Please help...thank you!

    Hi, how can I set up icloud for my ipad and iphone5? I missed tout he initial setup step and now want to have both the devices under icloud. Please help...thank you!

    Go to Settings>iCloud and sign in with your Apple ID to create the account.  Then turn on the data you wish to sync with iCloud.  See http://www.apple.com/icloud/setup/ios.html.

  • HT204053 can i set up a new icloud account and transfer files

    I have gotten divorced and really need to change my email address which is linked to icloud and has all my diary/itune/ibook purchases linked to it.  I understand i CANNOT change my email so this forces me to have to create a new icloud account.  How do i do this and can i set up the new icloud account to inherit my former accounts purchases?

    Go to www.icloud.com, go to the mail module, acess the settings (small gear wheel, on the right), choose Preferences>Accounts and create an alias in the lefthand panel.

  • Can U set breakpoint within a batch job and look at variables?

    Hello friends,
    I am trying to solve a problem that occurs within a program / transaction which can only be executed in background. The transaction in question is FPCOPARA and apparently this program cannot be executed in foreground.
    If I understand well, we cannot set breakpoints within a background job and as a result we cannot inspect variable etc. during job execution. So the question is how to achieve the same goal within a batch job? How did you do it? As this is a standard SAP transacrtion, no program modification can be applied.
    Your help is greatly appreciated.

    Hi......
    After u have executed ur batch job..
    go to sm37 >>select ur job using checkbox>>enter 'JDBG' in transaction box and press enter
    now debugger will start ..initial it will go through system code..after after a while the debugger will reach to your code and den you can debug the remaining report....
    all the best
    regards
    vivek

  • Can I set up my own domain email and FTP with iCloud?

    Hi,
    I have my own domain name and I would like to have my own domain email using iCloud. Is that possible?
    Also, if I buy storage, can I set up a FTP so I can share files with working clients?
    I noticed Google Apps let you do these things but since I am a Mac guy I am wondering if iCloud would be easier to set up and manage it.
    Thanks for any feedback.

    You cannot use your own domain name with iCloud email - it handles only its own email. The only thing you can do is forward email from your domain's email account to iCloud, but then you can't answer using it as you can only send using iCloud's outgoing server with the iCloud address as the 'From' address.

  • How can I set up itunes with one ipod and two laptops?

    My boyfriend gave me an ipod a few months ago and he let me set up itunes on his laptop so everything is there. now that i have my own laptop i want everything thats on his laptop on mine. The itunes part i mean. but i don't know how can anyone help me?

    Do as this article says:
    Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities
    That will make your iPod the syncing computer.
    You can only have one syncing computer/iTunes library for apps. and photos. You can however, manually sync music and vides from multiple computer/library if you sync manually. See that topic of:
    iTunes 11 for Windows: Set up syncing for iPod, iPhone, or iPad

  • How can I set up FaceTime between an touch and iPad 2 when they are both registered to same iTunes account ??

    My son has iPod touch and husband iPad 2. They would like to FaceTime each other but both devices are registered to the same apple Id on the same email address.( my son is only 8 so not his own email address)  clearly as FaceTime uses email address they can,t FaceTime the same email. So how do we do this. Can we have 2 email addresses on the same apple I'd. Really not vey technical, but son is desperate to do this so he can talk to daddy at work.
    Thanks

    First set up FT with the same Apple ID.  Then for one of the devices, add another email address as the calling address and delete the Apple ID as the calling address on that device.

  • Tax codes - can you set up default value for rows and freight? HELP!

    Hello - I have two issues with tax codes:
    1. When adding  a sales order if any of the rows do not have a value for "Tax Code"  I will get an error "Row without tax was found".
    - How can I get all rows on my sales orders, documents, etc to default to a specific tax code? Or will users ALWAYS have to enter the tax code?
    2. When addring a sales order with Freight, if the order is added without adding a tax code to the freight I will get an error "Expense with tax was found"
    - How can I get the tax code have a default value? We always use the same tax code, so it is redundant to have to enter this information.
    Any suggestions?

    Hi Jhon,
    this is the simplest and best way to make a Tax Code default is Go to
    Answer for Question 1
    Administration -> Setup -> Financial ->  Tax -> Tax Code Determination (Click on this)
    in that screen you can set a default tax code for both sales as well as Purchase.
    If you want to set Tax Code based on Vendors or Customers or Items separately then you can use the Key Fields.
    Answer for Question 2
    Once you enter the Tax Code in the freight i think it takes the Tax Code itself, I'm not so sure about this one though.
    Hope this helps you out
    regards,
    Shreyas

  • Can't set File Hosting Locations on Show and Share

    Hi,
         I'm currently using Show and Share 5.2. I have it peered with the DMM and everything for the most part seems to be working fine. The problem that I'm having is that I can't seem to set and save the File Hosting Locations. I set it to store locally and it shows a valid password, but it will not save the setings. I've tried this in multiple browser: the latest firefox and IE. Any ideas?

    Are you using the Actual Appliances or are you testing with VMware images?
    Please gather and upload the following screenshots:
    * Go to the AAI interfaces for BOTH the DMM & the SnS.  Please provide a screen capture
      of the Pairing status screens for each appliance.
    * Go to the DMM --> Admin Module and get a screenshot of the services for the DMM & the SnS.
    Is there any error when trying to save settings?  Please provide the screen shot
    of that..
    Thanks
    T.

  • How Can I set Specific RingTone for one person and general ringtone for all?

    Hello All,
    I have a problem with ringtone. I want to set specific ringtone for manager in my 99 series ip phone. Customer needs to know when manager calls him, that is why he told me that he wants to set specific ringtone for Manager.
    Thanks a lot
    Bahlul

    Hi Bahlul,
    I don't see such a feature on CUCM where you can have a separate ringtone for a Directory number based on the calling party number. Even to have separate ringtones for different lines on the same IP phone you need to play with Distinctiveringlist.xml , but that too does not fit your requirement as it will always be the same ringtone for all the calls on that line. You may probably get this feature through some third party solution but i am not sure if it would be worth it for applying it on one phone only.
    HTH
    Manish

  • How can I set my background so it repeats and the background is then square next to square?

    Hard to explain but basically like that...

    Do you have a Pop or IMAP mail account?
    Pop mail accounts can only connect to server and see the Inbox. Emails are downloaded from server Inbox to mail account Inbox.
    re: 'For example If I create a folder and move some of my mails there,'
    Did you create the folder in Thunderbird or in webmail?
    Do you have this setting? View > Folders > All

  • How can I set my privacy tighter with Siri and Dictation?

    OK First of all, Apple needs to stop with the restriction of what you can say in posts. They keep deleting my stuff without allowing my QUESTION to be answered.
    First of all, when did this massive invasion of my privacy happen? Did it happen with the latest update to iOS 8.1? I know I did not have these pop ups until this update happened this week.
    I would like to know how to use Siri and Dictation WITHOUT such a massive invasion of my privacy?
    Did I ever have such privacy prior to iOS 8.1?
    I went to dictate a text message to my husband today and I get a pop up telling me that ALL my information is going to be shared. There is a "learn more" link and I click that and it has this long diatribe on how
    Apple takes the things I say and dictate and records them and sent to them to process my requests. My device will also send Apple other information, such as my name and nickname; the names, nicknames, and relationship with me (e.g. "my dad") of my address book contacts, song names in my collection, and HomeKit-enabled devices in my home (e.g., "living room lights") (collectively, your "User Data"). All of this data is used to help Siri and Dictation understand me better and recognize  what I say. It is not linked to other data that Apple may have from my use of other Apple services...
    there is a lot more but suffice it to say, it does NOT 'match' what is said about Siri and Dictation on the Apple privacy page. The phone privacy contract description has MORE things listed that are being recorded, used and stored.

    It only matches what I quoted. There is a lot more in the phone.
    I also had a lot more in my original post but Apple censored and then deleted it because they decided it was a rant.
    Apple's policy in my phone's privacy policy says a lot more.
    Apparently from your answer I am stuck with a massive invasion of my privacy? Are you so very comfortable with having everything you say recorded? What if you worked in a high security industry?
    I also asked if this was in effect prior to this latest update or not.
    What I had to omit. Check your phone's privacy page and compare to apple's web page I linked ( Settings > General > Keyboard >Dictation & Settings > General > Siri) and click on the About Siri or Dictation privacy...
    It goes on to tell me I can restrict Siri's and Dictation's ability completely by turning it off.
    It tells me that my personal information, voice recording and other things collected may be retained for a period of time to generally improve Siri, Dictation an functionality in other Apple products and services. <-- this right here contradicts the paragraph I quoted  by saying it indeed DOES use it for other Apple things. Also, HOW LONG is this "period of time"?
    If I want to 'erase' this information I can simply turn off then on Siri and or Dictation and lose what I have had recorded on me. THIS fully restarts the "learning" process all over again and in turn NEGATES all the stuff it learned in the past. The KICKER is that since apple "retains what it collects for a period of time" HOW does turning the services off truly "erase" what was taken in the past?
    Why can't the learning process be done directly on the phone itself without it being RECORDED and STORED by Apple?
    Now, before you go off and say how Apple respects my privacy, I know all of that. I just don't believe or trust it since all this iCloud hacking has been happening lately AND I am VERY conscious of what I put "out there" for all to see and take. I don't use social networking either due to the massive invasion of my privacy. Plus I find it silly. I will not be reduced to a low level of conversation where the simple "like" is the equivalent of a reply.

  • How can I set the parameters of global channels and tasks previously created inside my applicatio​n?

    Hi everyone !
    Before proceeding to the description below I think it´s important to say that I´m using NI USB-6008 as DAQ device and the driver used is DAQmx 7.5.
    I´m currently developing an application into which I intend to be able to have complete control of the DAQ device being used, i.e, I´ll be able to create, delete and change the configuration of global channels and tasks previously created, among other things.
    To achieve the ends specified above I´ve already developed two vis, one to create global channels and the other to create tasks, and these two are doing a fine job. After this, I thought I came to the easy part ... I think I couldn´t be far for the truth! I thought that everything I should do was to specify which channel or task I´d like to configure and then use a property node to get the results I wanted, but it´s not working ...there are some DAQmx property nodes I thought I could use to do it  but I didn´t find a way to change the configuration of the global channels, and none of these property nodes seemed to work, i.e, although the simple vis used to test them ran the chosen parameters didn´t alter at all, after each execution I used MAX to see if they had changed, and to my chagrin they hadn´t.
    Can anybody lend me a hand with this problem? As always, any help would be deeply appreciated !    

    Hi Giovani,
    There is a developer zone tutorial that discussus some advanced data acquisition features including programmatic saves of NI-DAQmx tasks, global channels, and scales.  This tutorial also includes an example program.
    I wrote a short program that creates tasks in MAX. Whenever I wanted to change a part of the task, I would just change that feature in the example program. Take a look at the examples and please let me know if you have any further questions.
    Regards,
    Hal L.
    Attachments:
    create task example.vi ‏33 KB

  • How can i set page zoom level using css and javascript in firefox.

    i have problem to set zoom level in firefox.
    document.body.style.zoom = 150%; is worked in IE and Crome but not working in firefox so pls. i want to know a alise property that are provide a same functionality to me.

    Currently there is now way of retaining zoom level across pages in Single Page Mode. We have noted down your request and this might get implemented in one of  our future releases. Thanks for the feedback.
    - Adobe Reader Team

Maybe you are looking for