Can I Stack Switches with differents Part Numbers? Is it possible??

Hi,
I have a doubt, I need to buy 4 Switches Cisco 3750-X, but 2 with UTP/RJ-45 Ports, and 2 with STP capability.
My question is, for example, Can I stack 2 WS-C3750X-48T-E and 2 WS-C3750X-24S-E??

Disclaimer
The Author of this posting offers the information contained within this posting without consideration and with the reader's understanding that there's no implied or expressed suitability or fitness for any purpose. Information provided is for informational purposes only and should not be construed as rendering professional advice of any kind. Usage of this posting's information is solely at reader's own risk.
Liability Disclaimer
In no event shall Author be liable for any damages whatsoever (including, without limitation, damages for loss of use, data or profit) arising out of the use or inability to use the posting's information even if Author has been advised of the possibility of such damage.
Posting
The only limitation of stacking different 3750X models is the feature set of the installed IOS.
I.e.: "The Cisco Catalyst 3750-X Series Switches with LAN Base feature set can only stack with other Cisco Catalyst 3750‑X Series LAN Base switches. A mixed stack of LAN Base switch with IP Base or IP Services features set is not supported."

Similar Messages

How to handle same product with different part numbers and pricing in SAP.

I am a new user and want to learn if the following scenario can be handled by SAP.
Our business buys a product from a supplier which has 2 different part numbers and prices. It is the same product. One is the primary product whilst the other is available only as an upgrade option with a different part number to a mainline product at a cheaper price .
Our issue is that we sometimes buy the upgrade option with a mainline product to get the better price even though these go into stock. Basically we need to have the items linked with both part numbers in SAP at different prices but inventory both in and out only going against the primary part number. Any ideas?

Thanks Jitin
I did give them different part numbers and then attached a Bom containing the primary part number against the upgrade option however I really need to have the secondary item as a sales and purchase item but non inventory so the stock comes from the primary part. Ideally if we receipt the goods in as the secondary number the inventory goes to the primary part. If the second number is an inventory item then I have the issue of the same part with different part numbers sitting in stock at different prices and having to rely on employees understanding the difference.
Sorry to be so confusing. I will do some more testing over the weekend and see if I can find a suitable solution.
Thanks
Martin

Can we invoke webservice with multiple parts in wsdl?

Can we invoke webservice with multiple parts in wsdl?
Thanks

Yes we can invoke a web service with multiple parts for the input message.
You just have to assign to the relevant parts of the partner link input variable before invoking.
Regards,
Shanmu.

Need help with licensing part numbers

Ok, here's the scenario:
I have abandoned my original plan to use an IAD2431 to run CUCME and gone with a 2901 instead, but after reading & searching and reading for hours, I can not make heads or tails of this licensing scheme. Can anyone please just review my environment description below and tell me what license part numbers to buy? Maybe I'm just an idiot, but I've never seen anything this ridiculously difficult to figure out.
(1) already installed 2901, with (1) VIC2-2FXO and (2)EHWIC-4ESG installed.
This router will do nothing at present other than run CUCME. I have obtained a 60 day UC evaluation license from Cisco, but I will need to replace this with a permanent license.
(8) 7975G's (spares - no license included)
(1) 7925G (spare - no license included)
I currently have two POTS lines coming into the residence and one external SIP trunk (dialin/dialout). I need for all three of these to be accessible to ephones on my system.
Router is running IOS 15.4(3)M and CME 10. Phones are all running latest (as of today) SCCP firmware.
So, in this scenario, what license part numbers do I need to purchase to make everything work?

Hi Darren,
U need to have feature license say FL-CME-SRST-100= [qty. depends] along with IP phone user license SW-CCME-UL-7925= [Depands on number of users]
Additionally, u need to have CUBE licenses for SIP Trunking[ FL-CUBEE-25]
U can also refer ordering guide for more details
http://www.cisco.com/en/US/partner/prod/collateral/voicesw/ps6788/vcallcon/ps4625/cme_ordering_guide.pdf
regds,
aman

Can I group charts with objects in Numbers 3.0?

In Numbers 2.1 I could group charts with objects and text. I can't get this to work in Numbers 3.0. The objects will group but not the charts.
I used this to create marked-up charts in Numbers and paste them into a Pages document.
(I just purchased a new iMac and don't have the old Numbers on it.)

The only way around this is to print to PDF and open in preview, then use the rectangular selection tool to select the are you want to add to pages, then copy, then paste into Pages.
You can post feedback to Apple using the menu item "Numbers > Provide Numbers Feedback"
There are several features that were dropped and may be added back in... see this link:
http://support.apple.com/kb/HT6049?viewlocale=en_US&locale=en_US

Merge with excel or numbers, is this possible

Is it possible to insert an excel file in pages so that I can make adres labels? Is it possible annyway to make adres labels in pages?

You can go to Avery.com and download templates. You have to register - give them your name and email - to be able to do this. I downloaded a blank template meant for Microsoft Word, which of course opens in Pages. Then you can save the Avery template as a Pages template, which you can re-use. It doesn't automate the process, but at least you can type in your own information, or copy/paste it.
Lots of people are writing about this problem. If we all leave feedback for Apple, maybe something will change in a future update.
Joan

Using 37xx stack switch can I send snmp messages as syslog ?

In my environment, we are having cisco 37xx stack switches, I want to know is it possible to use the switch config to send snmp traps as syslog messages to the Syslog-server.
In our case, we are using siem which has the ability to process syslog messages from different networking switches. What specific event I'm after is related to bandwidth utilization of the interface. It would have been great if there was existing syslog-event for exceeded bandwidth or increase in bandwidth beyond certain bps rate. The only place such information can be obtained is from snmp, but the siem station doesn't understand snmp, So I hope there are some setting which allows the conversion of snmp traps to syslog msg to be forwarded to destination.
Thanks.

The iPad cannot use your Android phone number at all so it will not in any way be associated with the device or your Apple ID. You will be using your Apple ID email address as your connect address to use Messages. If you want to look at it this way, your iPad/iMessages will be associated with your Apple account/Apple ID, not with the Android phone number.
Where some users get into problems is if they go from an iPhone number to an Android phone number. That is not what you are doing.

PowerBook G4 Aluminum 15" Keyboard Part Numbers

I'm replacing the keyboard on a 15" powerbook g4 aluminum.
There are two seemingly identical keyboards for this model with different part numbers on the ribbon cable: AEQ43PLU010 and AEQ16PLU039.
Are these two parts interchangeable, say as a result of different manufacturing sources or are there differences in the pin-out on the ribbons?
In other words, I'm replacing a AEQ16PLU039; can I use a AEQ43PLU010?
Thanks,
-Rob

Just a quick note. My 1.67 model was the last one before the switch to intel. The left shift key would sometime activate along with the option key, causing some really weird behavior. I took the thing apart and noticed the left shift key 'nipple' rubber had separated for more than 50% of the circumference. I patched it with some silicone caulk and it seems to be a little happier. Previous to that, I took apart an older 1.25ghz machine to swap keyboards, but the two are not compatible. The ribbon cables are different and the newer version also has cables that interface with the trackpad. Probably part of the multi-touch nature of the newer trackpads. Best of luck with your keyboard swap and all the tiny screws!

IPhone 3GS part numbers

We used to be able to check iphone 3G part numbers (MB048LL/A, etc...) and whether the part numbers are locked to carriers from this site. http://support.apple.com/kb/HT1937
Seems like the page has changed and we can't check part numbers anymore.
Is there any other way to check whether a 3GS part number is/isn't locked to a carrier?
Message was edited by: kisekioo
Message was edited by: kisekioo

Any luck with the part numbers for the country of origin. I have to say that you are correct that the page used to list the model # so you could confirm the phone was unlocked. When I bought my 3G last year I compared the country with the model # and could see that it was a factory unlock. Mine came from Italy which was on the unlocked list. No such luck this time as I am looking to confirm my next purchase of a 3GS 32G.

LMS and stacking switches

Hi everyone!
I was having a conversation with a friend and he assured that the LMS is stacking switches with up to 09 switches.
Anyone know if this is true? For all I know this is only done through the special interface stack (as in 3750 and 2960S).

LMS (and Cisco Network Assistant) manages Cisco switch stacks. And, yes, a stack is up to 9 switches.
I'm not sure what you're asking, though. Stacks are built by virtue of physically connecting the StackWise cables and that is independent of what, if anything, is used for network management.

NI CAN Boards compatibility with CANalyzer

Hi All, also me as Lvilla, I'am interesting to know if the NI CAN Board are compatible with the software CANalyzer.It's possible to test our cards with Vector's software?
Best Regards
Ben

I am also interested using NI CAN hardware with CANape.
I have asked/emailed people at NI and at Vector, but all replied with a hazy answer of "I dont think so..."
Please let me know if you hear more..

Exact Apple part numbers for original Discs that came with late G5 Quad?

If anyone happens to own a G5 Quad made 2006 and you still have the original Software Restore discs that came with it, I'd be much obliged if you would be kind enough to post the exact Apple part number(s) for said discs.
I have a Power Mac G5 Quad made in the third week of June, 2006, and it is my understanding that it originally came with either Tiger 10.4.2 or Tiger 10.4.4.
I'm very enthusiastic about this machine and very happy with its performance. I'd like to search through the stacks of gray OS discs at local second-hand electronics shops for a matching set of discs. It's more of a curiosity, as I do have retail Tiger and Leopard discs off of which the Quad boots just fine.
Thanks in advance.

Hi Ramon,
I actually have both sets of discs. I have the disc set which came with the G5 Quad I own and its 10.4.2 while I do have another disc set which is 10.4.4 and it has also a OS 9.2.2 disc of its own for classic. When I get home later today I can see what other discs I have.. I will post the part numbers for you when I get home.
Take care..
Romko

The background behind my pages has turned black, how do i get it to go back to grey? i have switched between preview, normal, bleed, slug and presentation and closed and opened in design and it is still black. I can't imagine layouts with the black backgr

the background behind my pages has turned black, how do i get it to go back to grey? i have switched between preview, normal, bleed, slug and presentation and closed and opened in design and it is still black. I can't imagine layouts with the black background please help!

or maybe the interface has been set to Dark?
Go to Preferences > Interface tab, choose Light from Color Theme dropdown on Apearance section (upper part of the window)

Where can we find the part numbers for Multisim and Ultiboard professional versi

I want to purchase Multisim an Ultiboard, professional version. We got a quotation with the following answer:
Part number: 852798-11J Upgrade, NI Academic site licence;Q3 2009 Department Teaching Circuit Design Software Option
Part Number:900798_11    NI academic Site Licence-Department Teaching Maintenance for Circuits Option Includes automatic SW upgrades for 1 year
I have no idea where I can find those part numbers on the NI web site and for me the qouotation reffers to the academic version not the professional.
Can anybody from NI clarify the mystery.
John

Johnnelu,
Thanks for your reply.   If you received a quotation, please email me directly with the quotation number and I will have someone update this for you. I am not sure why you would have received a quote on the educational version in place of the Professional version.
Specifically answering your PN questions... here are the current P/Ns for the Professional Design Suites (Multisim and Ultiboard).
NI Circuit Design Suite, Base ->          779930-09
NI Circuit Design Suite, Full ->            779928-09
NI Circuit Design Suite, PowerPro -> 779927-09
http://www.ni.com/multisim/professional.htm
You can get price information online - you will need to select the specific item on the left and
set your country code on the top.
Regards,
Patrick Noonan
Business Development Manager
National Instruments - Electronics Workbench Group
50 Market St 1-A
South Portland, ME 04106
Phone: 207 892-9130
Email: [email protected]

3850 switch stack upgrade with minimum downtime

I was wondering if it is possible to do an upgrade of the individual stack members one at a time?
Is it possible to go from one major release to another doing this?
Is it possible to do this going from one minor release to another?
Is it possible to upgrade one stack member at a time within the maintenance release?
Thanks

I was wondering if it is possible to do an upgrade of the individual stack members one at a time?
Ans: Yes you can, but the switch will leave the stack
Is it possible to go from one major release to another doing this?
Is it possible to do this going from one minor release to another?
Is it possible to upgrade one stack member at a time within the maintenance release?
Ans for all above 3: For Stack configuration to work properly, switches must have the exactly same ISO
Recommendation: If they're many switches in stack,
1. upload the IOS file in all the switches
2. change the boot order in running config by:
boot system flash: <new ios fiile name>
boot system flash: <old ios fiile name>
3. take the reload one by one & copy the running config
4. in this case, basically you would be making the new parallel switch stack by adding the reloaded switch with same config but with new IOS image

Can I Stack Switches with differents Part Numbers? Is it possible??

Similar Messages

Maybe you are looking for