Can i take SFM2 out from my 6500 core

Hi,
I have two core 6500 switches pls see the below commands
CORE1#sh fabric utilization
slot channel Ingress % Egress %
1 0 0 1
3 0 0 0
3 1 1 0
CORE1#sh mod
Mod Ports Card Type Model Serial No.
1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-S2U-MSFC2 SAL0607J3K8
3 16 Pure SFM-mode 16 port 1000mb GBIC WS-X6816-GBIC SAL06090G2R
5 0 Switching Fabric Module-136 (Active) WS-X6500-SFM2 SAD060705EJ
Mod MAC addresses Hw Fw Sw Status
1 0006.d65a.876c to 0006.d65a.876d 3.4 6.1(3) 7.2(0.35) Ok
3 0009.11e0.0cd0 to 0009.11e0.0cdf 1.3 12.1(5r) 12.1(11b) Ok
5 0001.0002.0003 to 0001.0002.0003 1.1 6.1(3) 7.2(0.35) Ok
Mod Sub-Module Model Serial Hw Status
1 Policy Feature Card 2 WS-F6K-PFC2 SAL06090FF3 3.0 Ok
1 Cat6k MSFC 2 daughterboard WS-F6K-MSFC2 SAL0551FG9K 2.0 Ok
3 Distributed Forwarding Card WS-F6K-DFC SAL0607J9KX 2.0 Ok
the traffic is always like this is it recommended to take out SFM2 from the switch as there is no as such load on the switch . What is the rough cost of this SFM2 module ...
rgds
sandeep

dear Amit,
do i need sfm2 in the below case also ??
1 2 Catalyst 6000 supervisor 2 (Active) WS-X6K-SUP2-2GE SAD04500K94
2 2 Catalyst 6000 supervisor 2 (Standby) WS-X6K-SUP2-2GE SAD04490KLW
3 16 SFM-capable 16 port 1000mb GBIC WS-X6516-GBIC SAD061100EJ
4 16 SFM-capable 16 port 1000mb GBIC WS-X6516-GBIC SAD061100GC
5 16 SFM-capable 16 port 10/100/1000mb RJ45 WS-X6516-GE-TX SAD06110108
7 0 Switching Fabric Module-136 (Active) WS-X6500-SFM2 SAD061506TP
9 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45 SAD060904S2
10 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45 SAD0604045L
11 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45 SAD06060427
12 48 SFM-capable 48-port 10/100 Mbps RJ45 WS-X6548-RJ-45 SAD060904R8

Similar Messages

Hi Guys, Im getting a secnond-hand Iphone 4S and im going to use it as an ipod. How will i set it up if i dont want a SIM Card?? And if i use a SIM card for the activation then can i take it out??

Hi Guys, so im getting an iphone 4S as a hamy-down and im gonna use it as an ipod without a SIM Card. Im going to put my backup data on it from my old device. How will I activate it? Can i use my family members SIM (SIM that has been used in an iPhone before) to activate it, then can i take it out and use it without a SIM.
Regards, PulseSol

You can't activate any GSM iPhone without a valid sim card installed. So, yes, you'll need a sim card to activate the phone. The sim itself need not be activated, but it must be valid & present. While you can remove it, after the phone is activated, I recommend you don't. If you ever need to restore the phone, or update the iOS, you'll need a sim card installed to do so.
Make sure whoever is furnishing the phone to you, follows the directions here, before you get the phone:
http://support.apple.com/kb/ht5661

Can i take live video from TV tuner? how? urgent help is needed

can i take live video from TV tuner? how?
i have downloaded this code for a web cam how can i adjust it to take live video from TV tuner
* WebcamPlayer.java
* Created on November 22, 2004, 4:09 PM
import javax.media.Player;
import javax.media.CaptureDeviceInfo;
import javax.media.MediaLocator;
import javax.media.CaptureDeviceManager;
import javax.media.Manager;
import javax.media.format.VideoFormat;
import java.awt.Component;
import java.applet.*;
import java.util.Vector;
* @author Administrator
public class WebcamPlayer extends Applet
private CaptureDeviceInfo device; // Contains the device properties
private MediaLocator ml; // Contains the location of the media comming from the webcam
private Player player; // the player
private Component videoScreen; // Component that is capable to show the player's visual component
public void init()
try
{ //gets a list of devices how support the given videoformat
Vector deviceList = CaptureDeviceManager.getDeviceList(new VideoFormat(VideoFormat.MJPG) );
//device = CaptureDeviceManager.getDevice("vfw:Creative WebCam NX Pro (VFW):0");
//gets the first device from the deviceList
device = (CaptureDeviceInfo) deviceList.firstElement();
System.out.println("Chosen device: "+device.getName());
//String str1 = "vfw:Creative WebCam NX Pro (VFW):0";
// de webcam indentifiseren
//device = CaptureDeviceManager.getDevice(str1);
//gets the location of the device, is needed for player
ml = device.getLocator();
// makes player and gives the streaming video location (that is locate in the MediaLocator)
// this oparation is blocking until Manager has made a player that is realized.
player = Manager.createRealizedPlayer(ml);
//starts the play
player.start();
//Gets a component from the player that can show the actual streaming from the
//webcam.
videoScreen = player.getVisualComponent();
//adds the component that displays the streaming to the applet.
add(videoScreen);
// Now the user can see the steam that is from the webcam in the applet
catch(Exception e)
System.out.println("no device");
thanks here is my mail if any wants to mail me [email protected]

just visit
http://javasolution.blogspot.com/2007/04/java-tv-api-overview.html

Can I take a frame from my project and use it as a custom menu background with CS4 and its Encore

My project is edited in CS4.
I moved it to Encore CS4.
I don't want to use any of the supplied menu templates in CS4 Encore.
I was hoping CS4 would be all I needed to create custom menus using scenes from my project.
My question is: Can I take a frame from my project and use it as a custom menu background with CS4 and its built in Encore or do I need some other element from the Adobe catalog to make these custom chapter menus and sub-menus?
Thanks Jim

OK, I'm back. Here are my steps for creating Custom Menus with PS, En and PrPro:
In PrPro, move the CTI (Current Time Indicator) to the desired Frame. Check Frames on either side, with the Program Monitor’s Magnification to 100%, or maybe even 200% (you’ll need to scroll, but get a really clear picture). You want the clearest Frame in that area. With AME, in CS4, you’ll want to Export that Frame as .TIFF, or .BMP. I use .TIFF for this.
Now, for a caveat. When you Import this Exported Frame into Photoshop, be sure to check the specs., especially the PAR. You may have to use Image>PAR to adjust this to match your Project’s specs. Or, all might be perfect - just check this out.
Now, at this point, I choose the Library Menu, Blank, so that everything is setup. One can create the Menu from scratch, but careful attention needs to be paid to the exact naming conventions. At the very least, unless you’ve done this dozens of times before, use that Blank Menu, or similar as a guide, so you get things done, as they must be done.
Using that Blank Menu, just drag the Layer from your Exported Frame to your Menu image. It will appear above the black Background.
Add, or manipulate your Button Layer Sets, as is required, keeping them together. Remember that Button #1 will be the Button Layer Set, that is lower down in the Layers Palette. This can play a roll with Button Routing, back in Encore. Lower Button Layer Sets will have lower Button numbers.
Now, I always rename my Button Layer Sets, keeping the required characters - just changing the name. I also do all of my Button text in PS, and make sure to turn OFF Sync Button Names.
When done, Save_As .PSD, and then Import_As_Menu into Encore. Note: if you start with the Blank Menu, you can choose Edit in Photoshop, and then when done in PS, you just need to Save, and it will update in Encore. This is a personal workflow choice. I do the Edit in Photoshop route, but it is not necessary. One just needs to Import the resulting .PSD into Encore with Import_As_Menu, so that Encore does all the things that it needs to and recognizes the .PSD as a Menu.
When deciding what to base your Menu on, remember that you can "populate" your Menu with Buttons from the Functional Content. I’d suggest studying these Assets, and picking the ones that work best for you. You can still alter/edit those back in PS, so you just need to "get close."
Pay special attention to the required naming conventions. You cannot deviate from those first characters in the Button Layer Sets. They MUST be followed.
If you have any questions, do not hesitate to ask.
Good luck,
Hunt

I am a small woman with huge wrist circumference, 177.6mm. If I order the black men's stainless steel watch how can I take links out if needed?

I am a small woman with huge wrist circumference, 177.6mm. If I order the black men's stainless steel watch how can I take links out if needed?

We are just users here, so we have no way of knowing...
I am sure that any question that is not easily found at or from the Watch Store page > http://store.apple.com/us/watch < can be answered by this method (from the bottom of that page)
Chat with a Specialist
Get all your Apple Watch questions
answered or get help finding the
right watch. Call 1-800-MY-APPLE
ÇÇÇ

How can i take Better pictures from my Sony Cybershot DSC-HX9V like DSLR?Kindly Best Settings...

How can i take Better pictures from my Sony Cybershot DSC-HX9V like DSLR?Kindly Best Settings...

Taking better pictures on an HX9v isn't something you can just 'do'. It takes learning and creativity.
Understanding how the camera works, and having a good imagination to use it.
Look at phone cameras for example, amazing photos.
If you're talking about image quality, that is, less noise, crisp sharp photos, etc, compact cameras in general just won't match the DSLR.
If you're talking about photos that look stunning, again, learn how to use the camera, and be imaginative (creative)
I have a couple of articles to understand the basics to a camera (I really need to find the time to add more) on my website:
http://d3studio.com.au/
One thing I'm definitely lacking on there is composition, and that's something you can learn on YouTube - compositions in a photo is very important when you're first starting out.
Put your 9v onto M (manual) mode, and try out the different things - learn how the camera works, think about what you want to shoot, and then do it.
Good luck.

HT1454 why i can not get video out from my ipod touch after i did the upgrade

why i can not get video out from my ipod touch after i did the upgrade

why i can not get video out from my ipod touch after i did the upgrade

HT1454 Can not get video out from my ipod touch 3rd gen. Any ideas? It should nt be diffiicult to do this on the 21 st century, or not?

After having spent EUR 130 on cables from apple, i still can not get video out from my ipod touch 3rd gen. Any ideas? It should nt be diffiicult to do this on the 21 st century, or not?

Backing up an iOS device will copy some data to a backup file within iTunes, but this excludes all media. You can also transfer iTunes Store purchases from the iDevice to iTunes but, without using a third-party tool, nothing else. As long as you do not sync the iPod with your new library, the media that's on it will remain ... for as long as it keeps functioning, is not lost, stolen, eaten by the dog, ...
You may also have an option to recover your previous library from your old laptop; as long as its hard drive isn't fried, a computer repair store or technician may be able to extract the drive, mount it in an external enclosure, and copy your data to another PC. Whatever you choose, there is no real alternative to having all your media on your computer, managed by iTunes, and regularly backed up to another device/location.

How can i take the pictures from my old ipod and transfer them onto my computer without deleting anything

How can I take the pics from my old ipod and transfer them onto my computer without deleting anything?

Pictures on an iPod are stored in a special format, optimized for the iPod's small lower resolution screen, to save storage space. iTunes puts them into that format when syncing. There is setting in iTunes, on the iPod's Photos screen (where you set up syncing of photos) for Include full resolution photos. If that checkbox was checked when you synced the photos to the iPod, THEN you can Enable disk use and find those photo files on the iPod in the Photos folder.
Otherwise, you cannot get your photos back, using iTunes. There may be third-party utilities that can extract individual photos from the iPod, but they will still be lower-resolution versions of the original photo.

How can I take an item from one image and move it to another image?

How can I take an item from one image and add it to another image, and rotate it to fit?

Carefully select the objects of interest in one image and then copy, scale and position them into the other image. Then touch up the composite.
Have to Love Photoshop for Retouching Images!

HT4623 when i finished downloading a usb cable and itunes logo appered so i plugged it in the itunes and it said i should take it out from recovery by restoring it.it took 3 hours but at last it didnt download what should i do?

when i finished downloading a usb cable and itunes logo appered so i plugged it in the itunes and it said i should take it out from recovery by restoring it.it took 3 hours but at last it didnt download what should i do?

Try holding the home and lock buttons until the iPad reboots. If it does not start up normally, then you will have to restore. To avoid any longer downloads, go to here: http://www.ipswdownloader.com/download-ipad-ipsw-files.php
and look for your iPad and download the latest firmware. When done downloading, make sure the file is in a easy place to get to. Then, go on iTunes and connect your iPad. Hold your shift key, and press restore. Locate the .ipsw firmware and restore. Make sure no programs are open during the restore proccess as it may interfere.

How can I convert/read out from a string Hex (8-bit), the bit 0 length 1

How can I convert/read out from Hex (8-bit), the bit 0 length 1 (string subset!!??) and convert it to decimal.
With respect to one complement and two complement ?

Just like Jeff, purely guessing here.
It almost sounds like you just need to Read from Binary File?
AND the 8-bit number with 1?
Need more details. What exactly do you have to start with? What exactly are you trying to get out of it? Examples help.
There are only two ways to tell somebody thanks: Kudos and Marked Solutions
Unofficial Forum Rules and Guidelines

Can I take a song from my iTunes library and make it a ringtone on my iPhone 4? If so how. Thanks

Can I take a song from my iTunes library and make it a ringtone for my iPhone 4 if so how thanks

http://osxdaily.com/2010/09/04/make-free-iphone-ringtones-in-itunes-10/

How can I get HDMI out from my macbook air(2011)?

How can I get HDMI out from my macbook air(2011)?

It's rather simple. Buy a Mini DisplayPort to HDMI adapter. And then a HDMI cable long enough to link your computer the distance between both devices.
Adapter
http://store.apple.com/us/product/H1824ZM/A/Moshi_Mini_DisplayPort_to_HDMI_Adapt er?mco=MTY3ODQ5OTY
Example Cable (buy longer one, if needed) You can these practically anwhere that sells HP TV's
http://store.apple.com/us/product/MC838ZM/A?mco=MTY3ODQ5OTY

How can I get hdmi out from 2006 macbook pro?

How can I get hdmi out from 2006 macbook pro?

You will need something like this:
http://www.amazon.com/DVI-HDMI-Cable-6ft-Male-Male/dp/B0002CZHN6/ref=sr_1_3?ie=U TF8&qid=1363820878&sr=8-3&keywords=dvi+hdmi
Ciao.

Can i take SFM2 out from my 6500 core

Similar Messages

Maybe you are looking for