Can I up grade my existing software on my I mac 9,1 to snow leopard & then to mountain lion software ?
Can I up grade my existing software on my I mac 9,1 to snow leopard & then to mountain lion software ?
Yes, you can do that according to specs yours is early 2009.
http://www.apple.com/osx/specs/
Note that 2 GB RAM is suggested as a minimum but 4 GB is more realistic for good performance.
EDIT: Also, check for compatibility with any third party apps.
http://roaringapps.com/apps:table
Similar Messages
-
Problem
High running Temperature
Specification
iMac 27 inch
Mac OS X Includes Software Snow Leopard upgraded to Mountain Lion OS X 10.8.03 (1278)
251 GB Flash Drive
2 TB Sata disk
Processor 3.4 Ghz Intel Core I7
Memory 16 GB 1333 MHz DDR3
Graphics AMD Radeon HD 6970 2048 MB
Video: Software Final Cut Pro X 10.0.8
I use the imac mainly for editing Video which when doing so it has reached temperatures of near to 60° C which causes the program to become unstable and needs to be cooled down to operate correctly.
An Apple technician (by phone) advised me to download an smcfancontrol. This allows each individual fan to increase speed and also advises the current temperature at °C. The smcfancontrol has been downloaded but this has not resolved the problem. By increasing the speed of the fan more heat is generated and creates additional noise.
I have since taken the iMac to an Apple Store for examination as suggested by APPLECARE when the fans were found to be working correctly. An Apple Store technician carried out a test, but not whilst working under the pressure of FINAL CUT PRO when the iMac generates a high temperature.
The Temperature Specification for this model is
Operating Temperature 20 °c to 35°C
Storage Temp.47°c
Clearly the temperature my iMac is operating at is excessive and could cause the computer to break down prematurely. Has anyone experienced this problem.
Frank HowellWhen was the last time you cleaned/vacuumed out all of your iMac's vents, slots and ports.
You need to do this with the iMac powered down, disconnected from power and everything disconnected.
Lay your iMac, screen down, on a soft surface, like a heavy towel. Use a small electronics vac, or portable or full size vac with hose and a crevice tool attachment and carefully and slowly vacuum every vent, slot and port on your iMac.
Then reconnect everything up, power up and download and install iStat Pro. Start working, then report the temps of your iMac after this has been done.
When using SMCFan Control, it is important not to run the fans at too high an RPM. This doesn't generate heat on its own, but will suck in more dust, lint and dirt into your iMac, and that will be the cause of additonal increases in heat.
I run my fans in the range of 1400-1600 RPMs. You can go as high as 1800 RPMs but it is important to keep the RPM range below either 1800 or below 2000 RPMs.
I, also, run a very small desktop fan pointed toward the upper back of my iMac to keep temps down even further. -
Updated from Leopard to Snow Leopard, then upgraded to Lion, now my system is freezing on startup. Can anyone help?
Try a Safe Boot: Restart holding down the shift key until you (hopefully) see a grey progress bar. Once booted restart as normal from the Apple menu. Any change?
How much RAM do you have installed? -
So my mac is pretty much useless becuase i can't install mountain lion after a restore of my mac.
I have an imac late 2008 which i bought second hand. It only had Leopard OS X. So I bought the Snow Leopard OS X discs and installed them. I then bought Mounain Lion Straight from the app store and downloaded that.
However I recently decided to restore it for extra space. So i restored it fine and then attempted to reinstall Mountain Lion. Then a message popped up saying that 'This Apple ID has not purchased Lion' meaning that i can't now install Mountain Lion.
I then inserted the Snow Leopard disc and then it would not give me the option to install it on my hard drive and there was a little yellow caution sign on the picture of the hard drive.
I am stumped for ideas now and REALLY NEED SOME HELP
Thanks,
FinIf you installed Leopard that is why you can't install Mt Lion. The system Must be running Snow Leopard 10.6.8 to upgrade to Lion or Mt Lion.
If you only erased the Macintosh HD partition then you left the Mt Lion Recovery HD partition in tact on that system. At startup hold down the Command+r keys to boot to the Recovery HD Partition. From there erase the Macintosh HD partition and then select Reinstall Mac OS X. It should then download Mt Lion and ask you for the Apple ID that was used to purchase Mt Lion.
The Reason Snow Leopard might not be installing is because of the Recovery HD partition. To get rid of that you must First Re-Partition the drive As One Partition. Then install Leopard then SL (Or Snow Leopard from the start) and then update it to 10.6.8. Once that is done you should be able to log on to the Mac App Store and Re-Download Mt Lion. -
I am currently in the process of upgrading the operating system on my girlfriend's MacBook Pro (Model Identifier: MacBookPro5,1). I have purchased and installed Snow Leopard successfully, however I would like to upgrade to the latest operating system, which to date is Moutain Lion.
Am I able to do this?
Is it wise to perform such an upgrade on this model of MacBook Pro (can it handle it)?
I have heard that I can upgrade straight from Snow Leopard to Mountain Lion. What are the advantages and disadvantages of doing this? Will I lose anything at all by not installing Lion before Mountain Lion?
Thanks for the help everyone. Hopefully I can get these questions answered soon.And the only way to figure that out would be verifying my disk using the Disk Utility?
Thank you for that. If I am not missing out on anything by skipping Lion then that will be my option. A few extra dollars in my pocket is always a good thing. -
i have tried to update the iPhoto in an iMac from 2010 ( in which i have updated the OS from SnowLeopard to Mountain Lion 10.8.3) but it doesnt work,why? Is my iPhoto too old to update do i have to buy and install a new version of i Photo ?
You may need to buy the newest version from the App Store. If you cannot update via the App Store then you are using the version from a DVD. Updates for that can be downloaded from support.apple.com/downloads/.
-
I have a MacBook pro version 10.6.7 with snow leopard. After an scheduled software upgrade I could not open Quicken (It said it could not open the files). Now I can only open it if I have my external drive on. Can you help?
All the information that I had input on Quicken is gone. I have to have the external hard drive that I use to back up to be able to use quicken now. It is as if it was erased from the laptop hardriveTry repairing permissions. My favorite way is with a utility called AppleJack. Info and download here. It's free. It only works when you boot in Single User Mode. When restarting or booting, hold down the Command key and S keys.
You will get a very different startup screen that looks like the Terminal app has hijacked the screen. Just let the lines of text scroll by. When that happens you will get a text entry prompt. Type in "AppleJack" without the quotation marks.
A DOS looking menu will appear. Choose 1 or d to run Disk Repair. If you get a message that Disk Repair found and corrected errors, run it again. Repeat until you get the "your disk appears to be ok" message. This rarely happens with my experience, though. This does the same thing as as booting from an external drive and running Disk Utility's repair. Only, no external drive is required!
Next, choose 2 or p to repair disk permissions. This will take a little while. AppleJack warns that it will take up to an half hour to run repair permissions. It'n never taken more than about ten minutes for my MacBook Pro.
As permissions are repaired, you will see each repair scroll on the screen. When done, the menu returns, choose q to quit. Then at the prompt, enter "exit" without the quotes. Your MacBook Pro should restart into Mac OS normally after this.
Hope this helps. -
I have apple macbok"core2duo" 2.4 13'black,08 mac osx 10.5.8
can i upgrade to mountainline software?First you must upgrade to Snow Leopard 10.6.8. Then you can download Mavericks, if your computer is compatible, or Lion if it is not. See below:
Upgrading to Snow Leopard
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.
Snow Leopard General Requirements
1. Mac computer with an Intel processor
2. 1GB of memory
3. 5GB of available disk space
4. DVD drive for installation
5. Some features require a compatible Internet service provider;
fees may apply.
6. Some features require Apple’s iCloud services; fees and
terms apply.
Upgrading from Snow Leopard to Lion or Mavericks
To upgrade to Mavericks you must have Snow Leopard 10.6.8, Lion, or Mountain Lion installed. Purchase and download Mavericks (Free) from the App Store. Sign in using your Apple ID. The file is quite large, over 5 GBs, so allow some time to download. It would be preferable to use Ethernet because it is nearly four times faster than wireless.
OS X Mavericks- System Requirements
Macs that can be upgraded to OS X Mavericks
1. iMac (Mid 2007 or newer) — Model Identifier 7,1 or later
2. MacBook (Late 2008 Aluminum, or Early 2009 or newer) —
Model Identifier 5,1 or later
3. MacBook Pro (Mid/Late 2007 or newer) — Model Identifier 3,1 or later
4. MacBook Air (Late 2008 or newer) — Model Identifier 2,1 or later
5. Mac mini (Early 2009 or newer) — Model Identifier 3,1 or later
6. Mac Pro (Early 2008 or newer) — Model Identifier 3,1 or later
7. Xserve (Early 2009) — Model Identifier 3,1 or later
To find the model identifier open System Profiler in the Utilities folder. It's displayed in the panel on the right.
Are my applications compatible?
See App Compatibility Table — RoaringApps.
Upgrading to Lion
If your computer does not meet the requirements to install Mavericks, it may still meet the requirements to install Lion.
You can purchase Lion by contacting Customer Service: Contacting Apple for support and service - this includes international calling numbers. The cost is $19.99 (as it was before) plus tax. It's a download. You will get an email containing a redemption code that you then use at the Mac App Store to download Lion. Save a copy of that installer to your Downloads folder because the installer deletes itself at the end of the installation.
Lion System Requirements
1. Mac computer with an Intel Core 2 Duo, Core i3, Core i5, Core i7,
or Xeon processor
2. 2GB of memory
3. OS X v10.6.6 or later (v10.6.8 recommended)
4. 7GB of available space
5. Some features require an Apple ID; terms apply. -
Is there any Mountain Lion software that can do what Appleworks could
Is there any Mountain Lion software that can do what Appleworks could like drawing, painting, etc.? I find that Pages is very limited compared to earlier software or am I missing something? If Pages doesn't have this capability, what software can I get that does????
Hi,
Windows has a function called Narrator. Narrator reads what is displayed on the screen, including the contents of the active window, menu options, or text that has been typed. Narrator is designed to work with Notepad, WordPad, Control Panel programs, Internet Explorer,
the Windows desktop, and some parts of Windows Setup, and may not read words aloud correctly in other programs.
For more information, please refer the following link:
Turn on and use Narrator
http://windows.microsoft.com/en-IN/windows-xp/help/use-narrator
In addition, based on my research, a kind of third party program named JAWS. You could know well it first, and then decide whether you want to buy it.
Karen Hu
TechNet Community Support -
I just bought a new macbook pro, i lost my receipt which had a website on it that i had to go to were i would receive a code which i can redeem for the new mountain lion software. What do i do?
See Apple - Free OS X Mountain Lion upgrade Program.
-
I can't download my mountain lion software
I bought the Mountain Lion software and I can't download it from the Mac App Store. It's in my list of purchases but when I press download nothing happens.
It is a very large download, 4+GB and takes awhile, based on your internet service. Many folks later reply that it was quietly downloading in the background when they thought nothing was happening.
-
I posted a question which was: Can anyone please tell me which version of Photoshop Elements will work with Mac 10.6.8 Snow Leopard. Then this window popped up saying mark this discussion with as a question and this window. I have no idea how this works. It already is a question and if I need to emphasize that, how does this window that looks like a Word editing window, help me do that?Downloading, Installing, Setting Up
You asked the question in the title area instead of the area where the body of your posting is intended to be. No fault of yours - they need to make the form clearer.
Check the system requirements for the various versions of Photoshop Elements and see which suits your system. Adobe only sells the most recent versions of their software, so if you need an older version you will need to find a vendor for it.
System requirements | Adobe Photoshop Elements -
I upgraded to lion and many software didn't work. Downgraded back to snow leopard and now my initial login page
Is asking for my password. I put it in, but it's not working. Possible I have forgotten the correct one considering in think the last time I logged
In was when I bought the computer. But I think it's right. I did read something about if ur password was 8 characters or more it won't work? Anyone know? Or know how I can reset my password?Try this http://osxdeveloper.wordpress.com/2011/07/27/reset-10-5-leopard-10-6-snow-leopar d-password/
Allan -
I have two macs in my house. One is newer and came with the os x mountain lion software and the other one needs to be upgraded. I was wondering if there is a way to take upgrade from one to the other? Should not have to buy this software again.
Welcome to Apple Support Communities
Buy it for the other computer. Mountain Lion is preinstalled on the new Mac, but you can only use it in the new one -
TA48312 How can I download Mac OSX 10.6 snow leopard
Hi ,
I use to Mac OS X v10.5.8 but I want to update to my MacBook and I need to Mac OSX v10.6 snow leopard... ???Welcome to Apple Support Communities
Mac OS X Snow Leopard is not free. It can be purchased in a DVD at the Apple Online Store > http://store.apple.com/us/product/MC573Z/A/mac-os-x-106-snow-leopard
Before upgrading, make a backup of your files onto an external drive with Time Machine. After upgrading, open > Software Update to install Mac OS X 10.6.8, so you will be able to install iTunes 11.1.4.
If you want to upgrade to OS X Mavericks, see > http://www.apple.com/osx/how-to-upgrade
Maybe you are looking for
-
Hey! recently my key board settings has changed and now my volume buttons are no longer F10 and F11, now if i want to change the volume i have to do it on the top bar of the screen! how do i change it back to work normally on my wireless keyboard?
-
I'm having trouble with my 2 column layout... The text in my side panel is wrapping badly in IE, but perfectly OK in Firefox/Safari. Image widths are unaffected. I've got a layout that needs to fit to a repeating background (Y tiling) structure. My l
-
RSA3 check generated datasource error, ODS data can't be updated into cube
Hi Experts, I create an ODS( T_ODA01 ), and loaded data from flat file into this ODS. Of course, I activated the ODS after the loading process. Now Created an Infocube( T_CUBE01 ) similiar with the ODS. Next I want to update the data from ODS T_ODS01
-
Hi everybody, i am getting error as below ADF_FACES-60096:Server Exception during PPR, #2 javax.el.PropertyNotFoundException: Target Unreachable, identifier 'row' resolved to null at com.sun.el.parser.AstValue.getTarget(Unknown Source) at c
-
Argh! Hit escape twice after capturing tape!!! Where did my footage go???
So yah... This has happened to be several time before... As soon as I finish capturing the full tape, I hit escape to stop capture... Sometimes it looks like the program did not realize I hit escape, so I hit it again... That is when the window opens