Can I use a second generation Airport Extreme to extend my Time Capsule network?

I have a second generation Airport Extreme (circa 2009?) and am thinking of buying a Time Capsule. Can I use the Extreme to extend my network?

Yes. Note; however, you won't be able to extend the 802.11ac mode of the new Time Capsule. Also be aware that the 2nd generation Extreme did not provide for simultaneous dual-band operation. That would mean that you will only be able to extend either the 2.4 or 5 GHz band, not both at the same time.
... so it can work in a limited fashion.

Similar Messages

How can I force my Second Generation Airport Extreme to use 2.4GHz when extending the network of my Fifth Generation Airport Extreme?

Hi,
Would be great if anyone can help. I have setup my Second Generation Airport Extreme to extend the network of the Fifth Generation Airport Extreme. The 2nd generation Airport extreme seems to automatically get set to use 5GHz vs 2.4GHz. I would like to force it to use 2.4GHz so my older devices can connect to it. Any help would be appreciated.
Thanks,
Mike.

Enable the option to assign a different name to the 5 GHz network on your 5th Gen AirPort Extreme.
Then, the 2nd Gen Extreme will only "see" the 2.4 GHz network, and extend that signal.
If you are not sure how to do this, post back to tell us what operating system you are using on your computer so we will know what version of AirPort Utility you are using....so we can provide the correct steps for the setup.

Using Airport Express to Extend a Time Capsule Network: Results (*Long*)

Thought I would share my recent (2 hours ago) experience with setting up an Airport Express to Extend a Time Capsule 802.11N 5Ghz Network. Basically I just followed the directions in the Apple Airport Utility, using the "Extend a Wireless Network" setting:
Time Capsule (TC) 802.11N 5Ghz: In computer room
Linksys (LNK) 802.11g configured as dual network router with TC, also in computer room.
Airport Express (AE): In living room, about 50' away, several old plaster walls in between.
According to iStumblr:
1) I get an 80% signal from my TC when my MacBook is practically sitting on top of it.
2) I get an 88% signal from my Linksys 802.11g sitting next to the TC
3) I get 35% signal from my TC when my MacBook is in the living room. This is NOT enough signal, for some reason, to maintain a decent internet connection.
4) I get a 46% signal from my LNK from the same location. This IS enough signal to connect to the network.
5) With the AE configured as "Extend a Wireless Network" to the TC, and placed in the living room (again, about 50' from the TC base station), I get a 55% signal from the AE (which shows up as the same name as the TC network, for obvious reasons) Again, enough signal to connect to the network.
I did some internet speed tests using SpeedTest (take these with a grain of salt, of course)
1) From computer room over TC: 18Mb/s~22Mb/s average over 2 days of testing
2) From computer room over LNK: 18Mb/s~22mb/s average over 2 days of testing
3) From living room over AE(extended network from TC): 5~7Mb/s average in the last 2 hours
4) From living room over LNK: 12~14Mb/s average over 2 days of testing
Preliminary conclusions:
1) Setting up an extended network is pretty straightforward, and works without issue.
2) My 802.11g network with my old Linksys is far superior than my new extended 802.11N 5Ghz network, at least for internet connection speed.
3) I feel a bit irritated buying this AE now to extend my 802.11N network, if its not going to give me any advantages over my ancient 802.11g network
4) File transfers may still be better over the 802.11N-I will test that out at some point.
5) I have not tried WDS instead of "Extend a Wireless Network"-not sure what the benefits would be.
Computer Notes:
MacBook Aluminum-MB(Al) 2.0 C2D (802.11n)
finds 8 wireless networks in my neighborhood (3 of them are mine)
MacBook White-MB(Wh) 1.83 CD (802.11g only)
finds 10 wireless networks in my neighborhood (3 of them are mine)
Oddly, the signal strength of my networks isn't that different between the two computers-between 2% and 5%, even though it can't see as many networks. The 2 networks the MB(Wh) CAN see are at around 21% and 25% signal-not sure why the MB(Al) can't see them at all.

Your biggest mistake is confusing signal strength with signal quality. The signal indicator indicates strength and nothing else. You need to be using iStumblr to look at SNR (Signal to noise ratio).

Can I boost the DSL signal using my 1st Generation Airport Extreme or Express? Also, can I get wireless printing?

Can I boost the DSL signal using my 1st Generation Airport Extreme or Express?
I just moved into a house where they have ATT DSL and it is really slow in my room. I am hoping that I don't have to purchase a booster and I might be able to use my Airport Extreme or Express to boost it. I don't think they want my Extreme as their router, though. They are PC.
I am also hoping that I can set up a wireless printing situation in my room using the Express or Extreme.
I am running 10.4.11 on my old MacBook Pro laptop, 10.5.something on my old desktop (MacMini).
Thanks for any help ahead of time,
Carole

Can I boost the DSL signal using my 1st Generation Airport Extreme or Express?
I just moved into a house where they have ATT DSL and it is really slow in my room. I am hoping that I don't have to purchase a booster and I might be able to use my Airport Extreme or Express to boost it.
Unfortunately, this won't work especially if you want the connection between the routers to be wireless. The two are just not compatible for configuring an extended network. However, it could work if you can have them interconnected by wire. In that case, you could configure them into a roaming network.
I don't think they want my Extreme as their router, though. They are PC.
This shouldn't be an issue as the AirPorts support wireless clients regardless of which operating system they are running.

Can I use my iPad with airport extreme to retrieve files from a USB connected hard drive?

Can I use my iPad with airport extreme to retrieve files from a USB connected hard drive?

Yes, I believe so. Please check out the NetPortal app. I don't have an iPad, but I use it on my iPod Touch to access files on my Time Capsule. It is available from the iTunes App Store.

Can multiple Airport Expresses be connected via ethernet to an Airport Extreme to extend a single WiFi Network?

I am a big fan of both the Airport Extreme and Airport Express. In my work environment, I need to create a good quality single wireless network around 2 large aircraft hangars and some offices at the perimeters. We have a good quality wired Cat5e ethernet network extended between the buildings and offices now. Is this possible and does it seem like a good practical solution? I think that 4 or 5 Airport expresses would easily provide good wireless coverage in the needed areas.

Can multiple AirPort Expresses be connected via ethernet to an AirPort Extreme to extend a single WiFi Network?
Yes, this will work just fine as long as any individual Ethernet cable run will not exceed much over 330 feet or about 100 meters.

How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly

I want to extend my wifi off my Time Capsule with an Airport Experess in a part of my house that has no data cable ran to it. How do I do this?
Thanks

No more meseges.
في ٢٦/٠٨/٢٠١٤، الساعة ٢١:٤٥، كتب Apple Support Communities Updates <[email protected]>:
New discussion activity
Bob Timmons has posted in the AirPort community.
How can I set up mhy Airport Express to extend my Time Capsule wifi wirelessly
Assuming that you have the model A1264 or A1392 version of the Express, it must be located where it can receive a strong wireless signal from the Time Capsule to be able to extend it correctly.
A good general location would be a point that is about half way between the Time Capsule and other area that needs more wireless coverage.
You will use AirPort Utility on your computer to configure the Express. An iPhone or iPad could be used as well.
We can provide more help....if you need it....but we'll need to know what version of AirPort Utility that you are using on your computer....or whether you want to use an iPhone or iPad to setup the Express.
https://discussions.apple.com/servlet/JiveServlet/downloadImage/2-26506753-46613 2/AboutAirPortUtility.png
To post a reply, go to the discussion in Apple Support Communities.
You are receiving this email from Apple Support Communities. You can change your email preferences in your Apple Support Communities Profile.
TM and copyright © 2014 Apple Inc. 1 Infinite Loop, MS 96-DM. Cupertino, CA 95014.
All Rights Reserved | Privacy Policy | Terms of Use | Apple Support

Can i use my old round airport extreme as a WiFi extension?

i have my new airport extreme plugged into the modem via ethernet and wish to extend its WiFi network in my house using the older round airport extreme.
is this possible, and if so how do i configure this?
thanks all - T

It will depend on if this "older round" AirPort is an 802.11b or 802.11g model. If it is an 802.11g version, then yes you could use it to create a WDS extended network.

Using an Older (802.11g) Airport Extreme as bridge with Time Capsule

Several people have inquired about the possibility of having older (802.11g) computers and devices connected through their Time Capsules without disturbing the 802.11n capabilities of their newer equipment.
The latest version of Designing AirPort Networks Using AirPort Utility --
http://manuals.info.apple.com/en/DesigningAirPort_Networks10.5-Windows.pdf -- explains (pp. 48-49) that one can configure a dual-band (2.4 GHz & 5 GHz) network of this type by setting up the "second device [i.e., the older Airport Extreme] as a bridge." What is lacking is a clear (at least to me) way of configuring the 2.4 GHz Extreme as such a bridge, although the text states that one need only follow instructions "earlier in this chapter" (which begins at p. 14). When I try to do this, the AirPort Extreme shows up as a separate network.
Obviously, I am doing something wrong. Can someone walk me through how to configure the AirPort Extreme as a bridge?
Thanks.

The MAC support people walked me through a solution to my question about using an older (802.11g) AirPort Extreme and a Time Capsule to form a dual network. The solution turns out to be pretty easy but I am posting it in case anyone else has a similar problem.
Here's what was involved:
N-capable equipment: MacBook Pro, IMac, Time Capsule.
B/G-capable equipment: AirPort Extreme (flying saucer 802.11g); Mac G4; older (802.11g) AirPort Express supporting a network printer; IBM ThinkPad running Windows XP (w/service pack 2).
Step 1: Using AirPort Utility (manual setup), I set the Time Capsule to run at 5 GHz (click on "Wireless" then "Radio Mode". Under the same "Wireless" tab, I assigned a 13-digit WPA2 password to this network (more about this latter). If you opt to use the 5GHz frequency, you have the choice of WPA2 or nothing. After saving your settings, exit out of the AirPort Utility; you are done with the Time Capsule.
Step 2: Reset the AirPort Extreme to its default settings by depressing the small reset button while the device is plugged in.
Step 3: I reopened AirPort Utility, accessed the Extreme and clicked manual setup. (You will loose your connection to the Time Capsule at this point, but this is okay.) At the top of the screen that opens in response to clicking "manual setup," click "internet" and set "connection sharing" to "Off (Bridge Mode)" Next click "AirPort" at the very top of the screen: under "Base Station" I named the Extreme as "G network" and set up a network password. Under "Wireless" I next set up a WEP 40 bit password which was identical to the WPA2 password I used for the Time Capsule. Using a WEP password was necessary, because some of the older computers were not WPA2 compatible. I kept the passwords identical simply as a matter of convenience.
Step 4: Connect the AirPort Extreme to the Time Capsule using an Ethernet cable between the WAN port of the Extreme, and one of the three LAN ports on the Time Capsule. There is a small, green LED recessed in the LAN port socket; if it lights up, you are in business.
Step 5: Using a pin, I reset the 802.11g AirPort Express to its default settings, opened AirPort Utility (no need for manual setup for this), named the Express "Printer" and added it to the G network in a conventional manner by following the setup prompts. (If anyone needs help with this, let me know). Exit out of AirPort Utility and reopen it to refresh; all wireless devices (3 in my case) should be visible and lighted green.
Step 6: I set up the MacBook Pro and the IMac to join the 5 GHz Time Capsule network, and everything else to run on the G network. At this point, everything appears to be working. I can, for example, print a document from my MacBook Pro (N-network) to the network printer which on the G-network. (Because the older computers belong to my daughters, I'll never know if file sharing across the networks is a possibility.)
I take no credit for any of this; it was all accomplished through the efforts of very patient MAC support people.
Carl

Extend present Time Capsule network with an Extreme

I currently have a wireless network in my house using a Time Capsule that is connected to the modem in the office. I bought a Blu-Ray player that is connected to my TV in the living room, and if I plug it directly in to a router using an ethernet cable, I can stream movies to my TV. Sooooo.....I found the old Airport Extreme I used before I bought the Time Capsule, and I would like to use it to extend my network to the living room. I have the Extreme plugged in right now by the BLu-Ray player, and the name I used for the old Extreme network is showing up on my laptop, as well as the new Time Capsule network. The Extreme is blinking amber. What do I need to do to just add this Extreme as an extension of my network so I can connect it to my Bu-Ray via a ethernet. Thanks.

Since you have the 802.11n AirPort Extreme Base Station (AEBSn), you can take advantage of the "extend a network" feature.
o If practical, place the base stations in near proximity to each other during the setup phase. Once done, move them to their desired locations.
o Open AirPort Utility and select the base station that will connect to the Internet.
o Choose Manual Setup from the Base Station menu, or double-click the base station to open the configuration in a separate window. Enter the base station password if necessary.
o Click AirPort in the toolbar, and then click Wireless.
o Choose “Create a wireless network” from the Wireless Mode pop-up menu, and then select the “Allow this network to be extended” checkbox.
o Next, select the base station that will extend this network, and choose Manual Setup from the Base Station menu, or double-click the base station to open its configuration in a separate window. Enter the base station password if necessary.
o Choose “Extend a wireless network” from the Wireless Mode pop-up menu, and then choose the network you want to extend from the Network Name pop-up menu.
o Enter the base station network and base station password is necessary.
o Click Update to update the base station with new network settings.
(ref: Page 46 of "Designing AirPort Networks Using AirPort Utility.)

Can I use an Airport extreme to extend my ATT wireless network?

Hi
I get my internet through an ATT DSL wireless router positioned up in my attic. I have a studio in my basement with 2 computers, a plotter, a laser printer and a fax/scanner/photo printer. I've run an ethernet cable down from the attic in to a central location in my basement. I've run ethernet cable from the three printers to that same location. I want to set up an unused Airport extreme base station in my studio to connect the plotter and two printers to my wireless network. One snag is that one of my computers has a bad airport card slot and needs to be connected to the network with an ethernet cable.
Can you help me solve this?

OK,
Got er done this weekend and I have extended the network to my studio. One problem though, My main computer keeps dropping off the wireless network. It connects for a second and then gone. I have solved this for the moment by disconnecting my scanner from the AEBS and connecting my main computer to the AEBS. I still have not connected my laser printer to the network, but will use its USB connection to connect it to the AEBS. I just need to go buy a longer cord.
Things work for now and I can work on some jobs this week. I plan to search the boards to solve the dropping off problem soon.
Thanks again for all of your help.

Can't update windows 7 service pack 1, can I use windows 8 for AirPort Extreme on my laptop?

I need help! I'm trying to set up AE with 3 laptops, a desk top, an ipad and two iPhones! Got the software downloaded onto all but one laptop. My laptop won't configure windows 7 service pack 1 so the AE software won't install. I've tried all Microsoft fixes and still nothing. Any ideas? Can I upgrade to windows 8 and proceed or can you tell me how to get this computer to configure properly?!

Hey Me little
You can set it up using the AirPort Utility app for iOS. It has the ability to set up the AirPort Extreme for you.
AirPort Utility
https://itunes.apple.com/us/app/airport-utility/id427276530?mt=8
Thanks for using Apple Support Communities.
Regards,
-Norm G.

Can i use more than one airport express to extend the airport extreme?

my house is too big, and i use one airport express to extend my network,but the other half of the house doesnt get access to the internet.The question is can i use another airport express, without any complications?

Yes, up to 255 if I remember correctly. But before you do that take a look at the products offered by QuickerTek to amplify the output power of a router and/or add gain antennae to help increase the router's range without the need for adding access points.

Using domestic power circuit airport extreme to extend a WiFi network

I use a Time Capsule as a WiFi device behind an ADSL router supporting MacBooks and iPhones 4 and 5. In parts of the house the devices struggle to find the WiFI so I want to extend the network into these dead spots. I have read that using WiFI to extend the network uses the 5GHz band and imagine that will have an effect on the overall performance as seen by the client devices.
Would there be any problems in using the power circuits with an airport extreme at a suitable location in the dead zone?
I don't think the problem I have is a configuration issue but is just the fact that there is a lot of potential interference in place e.g. satellite dish and antennae cables.

OK thanks. "Extending" a network using power line adapters obviates any question regarding interference affecting your wireless network, at least as connecting the Extreme to your Time Capsule is concerned.
Power line adapters use your house wiring as a substitute for the Ethernet cables that would normally connect network devices. Your AirPort Extreme and Time Capsule would be connected to one another through the adapters and your house wiring, instead of communicating with each other wirelessly. Both of them will still use their individual 2.4 and 5 GHz networks to communicate with your MacBooks and iPhones.
This is a potential solution for some people, but it involves the unknowns of premises wiring. Some devices work, some don't, and those that do might not work if they are relocated to different outlets even within the same home. Improper or substandard wiring is very common and almost certain to present a problem.
It's a compromise that may or may not work in your particular installation. All you can do is try it.

Using Airport Extreme as Bridge with Time Capsule

I recently replaced an Airport Extreme with a Time Capsule, which has been great. However, I would like to use the Airport Extreme in bridge mode to extend the range of my wireless network. I don't want to use WDS, so I've connected the two via ethernet. So, the setup is this:
Cable modem connected to Time Capsule WAN Port
Time Capsule creating 802.11N (b/g compatible) network
Airport Extreme connected to one of the Time Capsule's LAN ports
However, the Airport Extreme doesn't have an option for "Extend a wireless network" under Wireless Mode - it just has "Create a wireless network" and "Participate in a WDS network".
My goal is to have the Airport Extreme essentially acting as a remote antenna for the network being created by the Time Capsule. Is this not possible? Is it because of the difference in wireless speed (N vs. G)?

However, the Airport Extreme doesn't have an option for "Extend a wireless network" under Wireless Mode - it just has "Create a wireless network" and "Participate in a WDS network".
The "extend" option is only applicable to 802.11n capable devices. However this doesn't matter since the "extend" option and WDS are both used for wirelessly extending a network. Since you are not doing that, you will not use either of those.
You should configure the AirPort Extreme base station (AEBS) to create a wireless network. You would configure the AEBS to use the same SSID (Network name) as the Time Capsule as well as the same wireless encryption type/level/password. To reduce interference, you would configure the AEBS to use a channel as far from the one used by the Time Capsule as possible.

Can I use a second generation Airport Extreme to extend my Time Capsule network?

Similar Messages

Maybe you are looking for