Can i use cisco 2951 cme 9 router to connect different branch location ip phones together with different subnet?

hi all,
I want to do VoIP , with cisco 2951 router with cme 9.0. I just want to know can i connect differnt branch ip phone in differnt subnet in single centralized cme router 2951.
that is for differnt branch ip phone there is differnt dhcp pool and then interVlan routing or as such.
i have already done it for 1 location ,can i uses that single router to connect there all branch office?
thank you
regards,
vishakha

Yes that works. The phones get an IP from the local site with the info where to reach the TFTP-Server (which is typically the CME). From there the phones load a config file and learn the IP of the CME. The rest is pure routing from the phone to the CME.
I don't know where marin and thana is, just make sure that the delay and jitter between the sites is inside an accepted range of < 150ms (latency) and < 30 ms (jitter).
Don't stop after you've improved your network! Improve the world by lending money to the working poor:
http://www.kiva.org/invitedby/karsteni

Similar Messages

Can you use home share where there are 2 itunes on the same computer but under different user profiles?

Can you use 'Home Share' where there are 2 itunes on the same computer, but under different user profiles?

check out method one from this support article -> How to use multiple iPods, iPads, or iPhones with one computer

Can I use ipod touch 5th to mirror my screen on Apple TV via Airplay with out wifi connection?

Can I use ipod touch 5th to mirror my screen on Apple TV via Airplay with out wifi connection?

Welcome to the Apple Community.
Peer-to-peer AirPlay
With peer-to-peer AirPlay, your iOS device and Apple TV don't need to be on the same Wi-Fi network. If you have one of these products, you can use peer-to-peer AirPlay:
* iPhone 5 or later, iPad (3rd generation or later), iPad mini, or iPod touch (5th generation) using iOS 8 or later.
* Apple TV (3rd generation rev A, model A1469 or later) with Apple TV software 7.0 or later. Find out which Apple TV model you have.
To use peer-to-peer AirPlay, your iOS device needs to have both Wi-Fi and Bluetooth turned on.

HT204204 My phone crashed after updating it to IOS 8. I can't use it cause its stucked on the start up menu, the apple logo with black background.

Hi to all,
I hope someone can help me. My phone crashed after updating it to IOS 8.3. I can't use it cause its stucked on the start up menu, the apple logo with black background. Even when I restart my phone, it is still stuck on the start up menu, the black background with apple logo in the middle.

Slone,
I finally decided to turn this annoyance into an opportunity. After a lot of experimenting I found that my iPad was just fine under 7.1 if I simply restored it as new. I have a lot of time on my hands and I had 1424 apps on my iPad! This is why every attempt to restore took so long.
I decided to restore as new, spend a day restoring the apps I really used. Doing so gave me a quick iPad with only bout a quarter of the storage used.
Granted it was a pain in the arse, but I wrote it off as in the old days when you had to do this with windows 95 just to keep a stable system.
I DO have some data in a few files of the now unused backup but a quick google search finds a couple Mac programs out there that will allow you go extract audio recordings, app data files etc. from the backup. I'll do that someday if I even miss the files I've probably forgotten that are there.
Anyway, there was nothing wrong with my hardware. I think there were just some troublesome setup items that 7.1 didn't like. Once set up as new, the ipad was fine.
Good luck!

My router internet connection won't except googles 8.8.8.8. dns why can someone please help me, my router internet connection won't except googles 8.8.8.8. dns why can someone please help me

my router internet connection won't except googles 8.8.8.8. dns why can someone please help me, my router internet connection won't except googles 8.8.8.8. dns why can someone please help me

naaa didnt work if you or any body else has any other ideas im open cuase now im thining about just taking it into apple and getting a new one but my friend said that he recently did the exact same thing and the apple store declined him cuase it was jailbroken sooo i really dont know what to do ....the purpose of getting the knew ipod was to have imessge and the new facetime and know that it isent working i dont know what to do or how to do it the correct way...............but thnk u Eric Ross and llaass

I don't own a MAC. I can probably use one at the library. I am trying to publish my book with Apple's ibooks, etc. Since my files are in Word.doc or html; how can I format my book so as to publish it?

I don't own a MAC. I can probably use one at the library. I am trying to publish my book with Apple's ibooks, etc. Since my files are in Word.doc or html; how can I format my book so as to publish it?
www.amessageforthehumanrace.org

Use an aggregator and follow their instructions for formatting.

If I'm in Europe, can I use Skype on Droid Charge(via Wi-Fi) to call US phone numbers?

If I'm in Europe, can I use Skype on Droid Charge(via Wi-Fi) to call US phone numbers?
Obviously there's no voice or data roaming for Verizon 3G/4G/CDMA phones in Europe.... (or am I wrong?)
Thanks in advance!

Hello WCMack,
That was a great explanation on the situation. Just to confirm, Europe uses GSM for their wireless network. There are third party apps that will allow you to make calls via wi-fi on a wi-fi enabled device. This is largely due if wi-fi is available and if it's free.
From my experience, I was able to make wi-fi calls on my Iphone 4 in Greece without any problems last month. Since we don't own any towers in Europe, the service is hit or miss. Feel free to update us when you get back.
Enjoy your trip!...

Can I use Creative Cloud Applications on LINUX through Wine as It is possible now with box versions?

as in title:
Can I use Creative Cloud Applications on LINUX through Wine as It is possible now with box versions?
Are there any things to consider / do differently?

You are certainly welcome to try. We have not tested this environment in anyway and you may face difficulties with Adobe Creative applications that require heavy use of the CPU. I also would be surprised if Acrobat could be installed in this environment due to it's dependencies to system resources.

HT201311 Can I use personal hotspot as wifi to connect AirPrint printer?

Can I use personal hotspot as wifi to connect AirPrint printer and print?
Thanks. Appreciate your help.

Yes, that should work at least temporarily. Some printers are not constantly looking for WiFi networks, however, so you'll have to make sure the hotspot is setup and active every time you turn your printer on.

Can I use an OS X.3.x disk to test and repair a drive with OS X.2.x on it?

Can I use an OS X.3.x disk to test and repair a drive with OS X.2.x on it?
    I've recently got a used iMac G4 1GHz with X.2.x on it. I'd like to test and repair the HD on it, but It didn't come with any OS CDs.
    I have X.3.x install DVDs for an eMac. Can I boot the eMac OS 10.3.x disk from the iMac G4 and use it's Disk Utilities to check and repair the HD on the G4? I would be using an X.3.x disk to check the X.2.x drive.
Thanks for any info.
Joe

Niel wrote:
You actually don't need any disk. Restarting with the Shift key held down will silently run a check and repair utility.
(64877)
Thanks Niel for the info.
    Not sure what (64877) is. That number just gives this thread in the results, when I put it in the search box here.
    Anyway; after reading your reply, I did a yahoo search and found these pages confirming what you posted.
"Mac OS X: What is Safe Boot, Safe Mode?"
http://support.apple.com/kb/HT1564
"Safe Boot takes longer than normal startup"
http://support.apple.com/kb/TS1884
    I did the Safe Boot and it didn't take long at all, but then I don't have too much on the drive.
    After it booted I noticed the sound was not working, but one page did explain that not everything gets loaded in a Safe Boot. So after a restart, things seem to be working fine.
Thanks again for your answer.
Joe

Can I use a midi/usb cable to connect to garage band?

Can I use a midi/usb cable to connect to garage band? Or do I need to buy an interface such as M-Audio. I have the M-TRACK, but haven't connected it yet.

karbuckle10 wrote:
Do I need two cables back and forth between the M-TRACK or just one OUT from the piano and IN from the M-TRACK?
i must confess i haven't checked GBv10, but all previous versions (and i'm guessing GBv10 as well) have only supported MIDI-IN, so all you need is to run the keyboard's OUT to the interface's IN

Hey there! well i from india and i m facing problem connecting my debit card to the itune store ,as the very option is not there, can someone guide me how to get it connected , i have a mastercard debit card with me .please help me

hey there! well i from india and i m facing problem connecting my debit card to the itune store ,as the very option is not there, can someone guide me how to get it connected , i have a mastercard debit card with me .please help me

if you are signed in to iTunes with your AppleID, click on the AppleID > view account > payment information > enter in your information

Can I use Cisco Connect if I change the default router IP address?

I am adding my E3000 into an existing network behind a SonicWall firewall. I am using an address scheme of 192.168.168.xxx When I change the router address to 192.168.168.10 and disable DHCP in Cisco Connect, I am left with only being able to access the router through the web interface. This seems pretty lame; I've read other threads on Web vs. Cisco Connect. Is there a quick fix that will allow Cisco Connect to still find the router after I've made (just) these two changes?
--David C

Yes you still will be able to use the Cisco Connect software if you have changed the Routers IP address, But if you change the Router password of Wireless Security then you wont be able to use Cisco Connect software.

Can I use my WRT54G wireless router as a signal range extender?

Hello, I have a couple wireless routers in my home, and basically I guess I can only use one as the main wireless router.
I'd really like to know if I can use one, specifically my linksys WRT54G wireless G router as just a range extender for the wireless signal from the main wireless router. It would save me a bunch so that I wouldn't need to go buy an entirely new device for this. If there is ANY way.
please help
thank you

You can connect as many WRTs as you like to your network if you wire them together. They create a big roaming network then (or several different networks if you want that). You have to set up the "internal" WRTs as access points, though, i.e. you don't connect them through the Internet port to your network but through a numbered LAN port. Also make sure to turn off the DHCP server on the internal WRTs and to assign them a free LAN IP address in your LAN (usually 192.168.1.2,3,4 will work).
In a roaming network there is no main router. All wireless routers are the same in this respect. Your "main" router is only defined by the fact, that it hosts the internet connection. But from the side of the wireless is does not matter. For a roaming network, make sure to assign all access points the identical SSID and wireless security settings. The only difference in the wireless settings should be the channels, where you should use different ones if possible. 1,6, and 11 are non-overlapping and thus are best to be used.
O.K. This was with a wired connection. If you actually need a wireless bridge, i.e., connect to access points through a wireless connection without any wired connection between them, then you have two options:
1. Buy access points like the WAP54G or wireless bridges like the WET54G. They have can be configured for wireless bridging. A WRT54G with standard Linksys firmware does not have this capability.
2. Get a 3rd party firmware for your WRT54G if there is one available for your hardware version. I think not all hardware versions support 3rd party firmware. Check on the label underneath the router to see what hardware version you have. Search for "WRT54G" on wikipedia. You'll find an article about the different hardware versions, which 3rd party firmware projects exist and where to download it. 3rd party firmware usually adds functions like wireless bridging to a WRT. I know HyperWRT+Thibor works well on my WRT54Gv2. Remember, however, that uploading a 3rd party firmware will void your warrenty...

Can I use my WRV200 (VPN Router with Range Booster) as a Repeater?

Hello gurus
I have a unsecured wireless signal coming to my apartment. Can I use the above device to capture this signal and give me a wired port (to plug a network cable) for my VOIP phone?
Thanks
Fouwaaz

The Device doesnt have the functionality to be repeater. The device that you need is WET200 it is a wireless bridge that has a 4 ports on the back. Below is the Link for the Device http://www.cisco.com/en/US/products/ps10053/index.html

Can i use cisco 2951 cme 9 router to connect different branch location ip phones together with different subnet?

Similar Messages

Maybe you are looking for