Can I use ip address and hostname to establish Site 2 Site VPN?

Is it possible to use both; hostname or ip address while trying to setup an ipsec tunnel?
The scenario we have is that there is a customer who has one central site and 10 remote sites. Each site exists for a period of 3 to 6 months and then the staff moves to another location as a result the router/firewall and other IT resources are moved too. This requires me to setup and tear down tunnels from the head office as well as remote sites. To avoid this, i was thinking of using dynamic DNS which would save me a lot of work. Is it possible that I can setup VPN tunnels by either method i.e. hostname and ip address or do I have to stick with any one method only? As a reference the command used to identify peers is
"isakmp identity {address | hostname}"
The firewall version is 7.0(5)

Hi,
If you want to use IP addresses also then you could probably configure dynamic L2L VPN connections so that even if the IP address etc of the remote site changes, it is able to connect to the central site without making any change on the central device. For the remote sites that have the static public IPs, you can create static L2L VPN connections.
HTH,
Please rate if helps,
Regards,
Kamal

Similar Messages

How to configure IP address and hostname?

May I know any method to configure IP address and Hostname? besides change it from /etc/hosts and /etc/inet/hosts.
any other method?
Any command to change?

May I know any method to configure IP address and
Hostname? besides change it from /etc/hosts and
/etc/inet/hosts.
any other method?
Any command to change?Yes, to do it temperiorly you can use ifconfig command, but after the reboot, these things will go off.
The syntax is:
ifconfig <interface> <ip addr> netmask <input based on your nwt> broadcast <> up.
ex:
ifconfig ce3 180.144.67.40 netmask 255.255.0.0 broadcast 180.144.255 255
HTH,
Prabu.S

How to change IP address and hostname in solaris 9

Hi experts,
I want to change IP address and hostname of the server , Plese give steps, or any precise document .
Thanks
Mohan
Message was edited by:
mohan_sr

did you already change your ip and host?
if not, do the following instructions:
* verify your hostname
- uname -a
- cat /etc/nodename
both should show your hostname
* alter your hostname
- uname -S newname
* verify the hostname
- uname -a
- cat /etc/nodename
both should show your newname
* edit /etc/hostname.ce0 (type ce0 depends on your net device)
- echo 'newname' > /etc/hostname.ce0
* verify /etc/hostname.ce0
- cat /etc/hostname.ce0
should show your newname
* edit the following files
- /etc/net/ticlts/hosts
- /etc/net/ticots/hosts
- /etc/net/ticotsord/hosts
replace old with new hostname
* edit /etc/inet/hosts
replace ip and hostname
* you have to look for
- /etc/inet/networks
- /etc/inet/netmask
fit yout data
After doing all changes you have to reboot your system.
Use ipconfig to verify network data

Can't use "Insert addresses" in Yahoo mail.

I can't use "Insert addresses" in Yahoo mail using Firefox. Nothing happens at all when I click on it. However, I can using Internet Explorer and it also works in Linux so it must be a problem with Firefox only! I have rebooted many times and even started up in "Debugging Mode". No luck so far with anything. Help PLEASE!

Yahoo may want to make their site work with Firefox. Please contact Yahoo for further assistance. Or check your plug-ins.
Please check if all your plugins are up-to-date. To do this, go to the [http://mozilla.com/plugincheck Mozilla Plugin Check site].
Once you're there, the site will check if all your plugins have the latest versions.
If you see plugins in the list that have a yellow ''Update'' button or a red ''Update now'' button, please update these immediately.
To do so, please click each red or yellow button. Then you should see a site that allows you to download the latest version. Double-click the downloaded file to start the installation and follow the steps mentioned in the installation procedure.

Can not use ip address to access dynamics crm page

Hi All,
I can't use ip address in url to access or call my crm page from client computer browser, instead of use computer name.
these are my troubleshoot steps:
1. ping from client computer to crm application server with ip address (OK)
2. turn off all windows firewall (domain network, home or work, public network)
please advise.
thanks.

You will need to provide some additional detail about your setup.
Version of CRM?
Is IDF and/or ADFS setup?
Some basic things to check:
From the client computer, does a nslookup of the CRM server name resolve? If not, it may be a DNS issue.
Is the CRM site in IIS listening to all IP addresses? Or set to listen to only one?
Was a host header set up in IIS for the CRM site?
What error do you get when you use the CRM server name from the client machine? Only IP addresses working is a sign of a kerberos issue. Check that you have the correct SPN's created for a non machine account running the CRM app pool in IIS.
Jason Peterson

How can I use the "Copy and paste" tool in order get stamps in the same position in different pages (Acrobat XI for PC)?

With Acrobat 6.0 I was able to copy a stamp in the same position (I mean "exactly" the same one) of different pages just by using the "copy/past" tool.
Now I am using Acrobat XI and it seems like it is not possible anymore: I am copying a stamp and I am trying to past it in anoter page, but it appears in the center of the page (or wherever it wants to...).
Does anyone have a solution?
Thanks in advance.

Thank you very much. I'll be waiting for you message.
Messaggio originale----
Da: [email protected]
Data: 26/01/2015 17.56
A: "Umberto Gangi"<[email protected]>
Ogg: How can I use the "Copy and paste" tool in order get stamps in the same position in different pages (Acrobat XI for PC)?
    How can I use the "Copy and paste" tool in order get stamps in the same position in different pages (Acrobat XI for PC)?
    created by Gilad D (try67) in Creating, Editing & Exporting PDFs - View the full discussion
Well, I was in the same situation so I've developed a tool that allows one to do it. I will send you some additional information about it in a private message.
     If the reply above answers your question, please take a moment to mark this answer as correct by visiting: https://forums.adobe.com/message/7132586#7132586 and clicking ‘Correct’ below the answer
     Replies to this message go to everyone subscribed to this thread, not directly to the person who posted the message. To post a reply, either reply to this email or visit the message page:
Please note that the Adobe Forums do not accept email attachments. If you want to embed an image in your message please visit the thread in the forum and click the camera icon: https://forums.adobe.com/message/7132586#7132586
     To unsubscribe from this thread, please visit the message page at , click "Following" at the top right, & "Stop Following"
     Start a new discussion in Creating, Editing & Exporting PDFs by email or at Adobe Community
For more information about maintaining your forum email notifications please go to https://forums.adobe.com/thread/1516624.

1. I have an iPod which has purchases synced with I tunes with an apple ID. I now have an iPad with a new ID for cloud. I have cloud storage capacity of 5gb which came with the iPad. How can I use one ID and store my existing music in cloud?

1. I have an iPod which has purchases synced with I tunes with an apple ID. I now have an iPad with a new ID for cloud. I have cloud storage capacity of 5gb which came with the iPad. How can I use one ID and store my existing music in cloud?

HI Frostyfrog
CHeck out iTunes Match which has an annual fee of £21 or thereabouts. You can store a maximum of 25,000 songs there and they all become available on your other kit, iPhone, iPad and iPod. I know it works as I have over 23000 songs uploaded of which only a few we're bought through iTunes.
it works by comparing your music to the whole iTunes music dadata base so you access the same tunes that you could get from iTunes. If you have obscure stuff, it uploads your own music to the cloud as a copy.
I Find it incredible that on my iPhone with its 16gb memory I can view almost 200 gb of music (ie my 23000 songs) and play any of them. Anything I add to iTunes becomes available via the cloud fairly quickly from a few minutes or a little longer if adding a lot.
The first time you use it it will take quite a while to match your music if you have a lot, but after that it is all automatic. Read the stuff on the apple site. Your PC needs to be at least running Vista. I recommend it and at less than 50p a week it's good value.
Good luck

Can I use an iPad and a ipad2 with the same iTunes in my computer? I want to use both

Can I use an iPad and a ipad2 with the same iTunes in my computer? I want to use both. Want to give one to wife.do I need to open a new iTunes account for her?

bashepard wrote:
Can I use an iPad and a ipad2 with the same iTunes in my computer? I want to use both.
Yes, No problem at all.
Want to give one to wife.do I need to open a new iTunes account for her?
No - you can share the same iTunes account (my wife and I share the same account). But when you sync the iPads, just remember to select the correct content for her iPad and the correct content for your iPad.

Can i use this download and install on multiple computers?

Can i use this download and install on multiple computers?

I assume you're talking about the Lion installer? If so, yes, you're allowed to use it on any machines authorized with your Apple ID (which I believe means a maximum of five machines). This is, of course, meant for family use... I'm not sure about business use, but I'd suspect you need one copy per machine at a business. If you're in that situation, you may want to wait for the $69 Lion flash drive Apple will be releasing next month sometime, as that won't be tied to an Apple ID. But check with Apple to be sure on that.

When I sync my iphone 4S using iTunes it only syncs 8.5GB of music, not the entore library as specified. Is there a capcity default limit of the amount of storage that can be used for music and if so how do I change it?

When I sync my iphone 4S using iTunes it only syncs 8.5GB of music, not the entore library as specified. Is there a capcity default limit of the amount of storage that can be used for music and if so how do I change it?

The only limit is that of the device. No restrictions on how much of it you can use for music. Is part of your music library unchecked?
tt2

Can I use Adobe Premiere and Photoshop (with cloud license) on more thn one computer.

Can I use Adobe Premiere and Photoshop (with cloud license) on more than one computer? WHen on the oroad I would like to use it n my laptop, while I installed on the desktop.

Hi Kasiah,
As per the EULA accepted while you launch Adobe applications you can download & install on 2 systems but can use on one at the same time.
Source:http://www.adobe.com/in/products/creativecloud/faq.html
Let me know if you have any questions on this.
Cheers~!
-Mandhir

I have a macbook pro with 10.6.8 on it but I need to do a clean re install and my CD is 10.4.6. Can I use the CD and then are my OS updates to 10.6.8 free?

I have a macbook pro with 10.6.8 on it but I need to do a clean re install and my CD is 10.4.6. Can I use the CD and then are my OS updates to 10.6.8 free?
Also can I use iMac OS install disks on a MacBookPro?

You will have to buy Snow Leopard:
You can purchase Snow Leopard through the Apple Store: Mac OS X 10.6 Snow Leopard - Apple Store (U.S.). The price is $19.99 plus tax. You will be sent physical media by mail after placing your order. You also should find it at your local Apple retailers.
After you install Snow Leopard you will have to download and install the Mac OS X 10.6.8 Update Combo v1.1 to update Snow Leopard to 10.6.8 and give you access to the App Store. Access to the App Store enables you to download Mountain Lion if your computer meets the requirements.

How can i use this sript and loade another movie?

Hi there, i used the following script to load a movie from the server;
var request:URLRequest = new URLRequest("url string");
var loader:Loader = new Loader()
loader.load(request);
addChild(loader);
How can i use this sript and loade another movie? Can someone help me please?
[edited by moderator]

Sir, I changed it from:
var request:URLRequest = new URLRequest("http://agusandelsur.gov.ph/downloads/pdrrmo/agusan_del_sur/StaJosefa/Movies/Dir.swf");
var loader:Loader = new Loader()
loader.load(request);
addChild(loader);
to
var request:URLRequest = new URLRequest("http://agusandelsur.gov.ph/downloads/pdrrmo/agusan_del_sur/StaJosefa/Movies/Warning.swf");
var loader:Loader = new Loader()
loader.load(request);
addChild(loader);
When i expord the movie i get the following error.....
Scene 1, Layer 'Layer 3', Frame 1, Line 6 1151: A conflict exists with definition request in namespace internal.

Can I use a select and update statement in a single jsp file?

I want to update the BUY table everytime I would add a SELL transaction.....I want to minus the stocks that I sold to those that Ive bought before.....
note: I used a seperate table in BUY and SELL transaction
After I Have added a transaction, I want to update the buy table. This is my problem, can I used both SELECT and UPDATE statement at the same time in a single jsp file for example like this:
select * from test, test1;
update test
set total_shares=total_shares-Stotal;
where stock_code=Scode AND name_broker=Sbroker;
Can i have both of these statements in the same jsp file in oder to update the buy table?
Or can anyone suggest how can process that update?THANKS!
--------------------

Can i have both of these statements in the same jsp file in oder to update the buy table?Yes. But wouldn't it have been easier just to try it?

Can I use Time Capsule and LaCie at the same time?

Can I use Time Capsule and LaCie at the same time?

stephaniefromarlington wrote:
Before I answer your questions, let me first just say thank you so much for your amazing patience and helpfulness. Whether or not we get to the bottom of this, I am very, very grateful to you.
We will get to the bottom of it, and you're quite welcome. Don't feel you ought to know all this stuff -- none of us were born with it!
By the way, in answer to your original question, yes, you can use the Time Capsule while backups are running. There's no conflict at all.
1) Estimated size of full backup: 205.94 GB
2) My LaCie has available: 11.04 GB of 359.95 GB
That's part of the problem right there; 360 GB is a bit small to back up 206 GB. Ordinarily, a Time Machine drive should be 2-3 times the size of the data it's backing-up, so Time Machine can keep a reasonable "depth" of old backups for you.
It looks like Time Machine is trying to do a fairly large backup, and there just isn't enough room for it.
But something doesn't quite add up. Time Machine should have deleted all but your most recent backup, trying to make room for the new one. But that would mean there should only be a bit less than 206 GB on the disk, not 360.
A clue may be lurking in your logs. Use the widget in #1 of Time Machine - Troubleshooting to display the backup messages from your logs. Locate the backup in question, then copy and post all the messages here.

Can I use ip address and hostname to establish Site 2 Site VPN?

Similar Messages

Maybe you are looking for