Can I use my G5 Dual 2.7Ghz drives in a new Mac Pro?

I currently have 2 drives in G5 and would like to move them over to a new Mac Pro Tower, they being a WD 740GD SATA high speed drive as well as my boot up 700G SATA drive. Are they compatible and has anyone had issues? Cheers.

Actually, the drives might need to be reformatted because your G5 uses PowerPC processors, which need to be formatted using the Apple Partition Map.
Your Mac Pro is an Intel machine, so the drives will need to be formatted using the GUID partition; disk utility can take care of this for you.

Similar Messages

  • Possible to re-use G5 serial-ata drives in a new Mac Pro?

    I am getting ready to retire a Power Mac G5 Quad and am wondering whether I can take its two serial-ata internal hard drives and install directly into two of the empty slots I have in a new Mac Pro? Any issues that I should be aware of?
    Thanks in advance for your assistance.
    Brymer

    FWIW and just in case, guide to migrating.
    http://discussions.apple.com/thread.jspa?threadID=435350
    And the Quad G5 seemed to be the only G5 that could actually use GPT format (probably preparing for transition to the Mac Pro I'd guess). Was also able to use NCQ and some other SATA II (2.5) features and specs.

  • How to use hard drives with the new mac pro

    A few quick questions about upgrading to new Mac pro desktop
    I currently have 4 internal hard drives for a total of 8T
    What will the solution be to add storage to the new desktop?
    I assume it will be thunderbolt options?
    Lets say I wanted at least 8TB of storage to add to the computer
    and attached the storage via thunderbolt will it be as fast data throughput
    as the harddrives in my current computer hooked up to the external bus?
    I also have a pci card running my audio plugins for Universal Audio how will those pci
    cards work on the new mac pro?

    Also will the transfer rate with the pegas be as fast as if the drives were connected to the bus in the machines like the old mac pro?
    To answer that, think of this as a Bottleneck problem. The overall performance is as slow as the slowest device.
    At this writing typical rotating drives can produce a momentary burst at 125 MBytes/sec or 1,000 Mbits/sec. Only FireWire 800 is starting to be a limit for that -- EVERYTHING else is faster. Thunderbolt-1 is 10,000 Mbits/sec -- ten times faster.
    The best SSD can produce a burst at maybe 800 MBytes/sec or 6,400 Mbits/sec. There is not a big speed difference in an SSD RAID, because the latency is already low. But the 10,000 Mbits/sec of ThunderBolt-1 is still plenty fast enough for that as well.
    If ThunderBolt-2 devices really can run a single data stream at 20,000 Mbits/sec, that does not make ANYTHING faster -- it just moves the ceiling (potential bottleneck) a bit farther away.

  • Can I use my 24" iMac as a second monitor for my Mac Pro?

    I bought a Mac Pro with the 27" Cinema display and it's great. Now I want to use my old 24" iMac as a second monitor.
    How can I make this work?
    I appreciate all you support!
    Thanks

    By using ScreenRecycler and a network connection.
    (59150)

  • Can i use Airplay with other applications different to iTunes on my Mac Pro?

    Hi,
    I bought a Mac Pro 13' Retina Display two weeks ago and today i bought a Bose SoundTouch 20 and i connected both to my home network by ethernet cord. when i try to use applications like iTunes to send the sound of a song from mac to bose it work perfect, but when i try to do the same with spottily (i downloaded the app for my mac) simply doesn't work and don't know why. Another issue is that either can't send the sound of the movies and videos from mac to bose (i already try this using this configuration: send by airplay the movie to apple tv and from apple tv send the sound to bose, all work perfect because all was connected with ethernet cord).
    So the question is, Anyone know why the Airplay function only work with iTunes and with other applications simply doesn't?

    AirPlay only works with iTunes for Mac OS, iOS devices, and Apple TV.
    Not third party (non Apple) apps such as Spotify
    If the Bose Sound Touch supports Bluetooth, you may be able to stream music to the Mac or Apple TV. That's for sound, not video.

  • Can I use a bluetooth keyboard on a non-bluetooth enabled (Old)Mac Pro?

    Sorry, this seems like something I could easily find an answer to, but I haven't found the answer on the forums or in google searches.
    My quad core Mac Pro is not Bluetooth enabled.  I'm assuming I can just use a USB Bluetooth dongle to talk to the keyboard.  I thought I would double check before I start spending money.  I do have a Belkin Bluetooth dongle already, but I've seen some talk about some talk about some other options from the Mac Store.  I'm just hoping to hear what has worked for others.
    Thanks!

    At Amazon:
    http://www.amazon.com/Targus-USB-Bluetooth®-Adapter-ACB10US/dp/B0002K6RK0/ref=sr _1_2?ie=UTF8&qid=1407538734&sr=8-2&keywords=bluetooth++dongle+mac+osx
    http://www.amazon.com/Sabrent-Bluetooth-Wireless-Adapter-BT-USBX/dp/B006ZZKPY0/r ef=sr_1_4?ie=UTF8&qid=1407538972&sr=8-4&keywords=bluetooth++dongle+mac+osx
    work fine Amazon says.
    Or get Apple bluetooth module at eBay.
    http://www.ebay.com/sch/i.html?_odkw=bluetooth+adapter+for+mac+pro&_osacat=0&_fr om=R40&_trksid=p2045573.m570.l1313.TR0.TRC0.H0.Xbluetooth+module+for+mac+pro&_nk w=bluetooth+module+for+mac+pro&_sacat=0
    Apple Menu > About This Mac > More Info... > System Report... > Bluetooth says bluetooth is detected, it mean bluetooth dongle is woking with system bluetooth driver.

  • Can I use my iMac as a display for a G5 - New Mac User

    I am still a fairly new iMac user, I would like to know if I can use my exsisting iMac with someones elses G5, and use my iMac as a screen display for his G5. Im sorry if this topic does not belong in this forum, I did try searching thru other forums to post and read up on this info.
    Please direct me to the right place, or answer my question. Thanks in advance.

    Here's the scoop, if you want to use any iMac as an external display for a G5 Mac you have these options.
    1. Target Disk Mode, only available on iMacs with Firewire:
    http://docs.info.apple.com/article.html?artnum=58207
    This only gives you access to the data files of that Mac and basically treats it as an external hard disk.
    2. Networking via ethernet, wireless, or Firewire, you can setup Virtual Network Computing or Remote Desktop:
    http://www.macupdate.com/search.php?keywords=VNC&os=macosx
    http://www.macupdate.com/search.php?os=macosx&keywords=remote+desktop
    3. As others have suggested, somehow to remove the VGA cable from the logicboard of the iMac and connect it to the Mac externally.
    The external VGA port of iMacs only display what is on the Mac itself and as far I know can't be used in a reverse signal application.

  • How can i move all the song from my iPod to my new mac pro laptop?

    how can i move all the song from my ipod touch to my new macbook pro?

    Syncing to a "New" Computer or replacing a "crashed" Hard Drive: Apple Support Communities
      Recovering your iTunes library from your iPod or iOS device: Apple Support Communities

  • Can I use Lion Server to sync files from my MBP and Mac Pro tower?

    I have a 2008 Macbook Pro and a Mac Pro I'd like to sync files between. I also have a Mac Mini that I'm considering for an OS X Lion Server install if it could help sync all my files across computers. Any suggestions would be greatly appriciated!

    There is a simple way for unmanaged clients.
    To point an unmanaged client to your update server, enter the following command in terminal:
    sudo defaults write /Library/Preferences/com.apple.SoftwareUpdate CatalogURL http://<your_server>:8088/index-lion-snowleopard-leopard.merged-1.sucatalog
    (replace <your_server> with the dns name of your update server.  If the unmanaged client runs snowleopard or leopard, adjust the url accordingly. For snowleopard clients, remove the "lion-" part. For leopard clients, remove the "lion-snowleopard-" part

  • How do you get all 4TB out of an internal hard drive being used as an external hard drive on a new Mac Pro?

    Currently I am only able to access 1.8TB. I am sure the fix is easy. Pleae help. Using a startech USB device to mount.
    Thank you.

    I expect Kappy is correct. The controller in the enclosure is limiting the size.
    You may need to buy a more modern enclosure.

  • Why can I not play any CD's or programs on my new Mac Pro. The message this disk is not supported.

    Hello?
    anyone there? Apple is closed and I'm about to throw this computer against the wall.

    Ah, are they Windows or something?
    did you migrate and transfer programs from another computer?
    you are using OS X and support for older powerpc based programs won't run unless you insall Parallels and Snow Leopard in a VM. Or upgrade all the programs to be Lion compatible.

  • Can I run two 2560x1440 monitors (dual link DVI) on a new Mac Pro?

    I have two Monoprice Zero-G IPS monitors, which can run at resolutions of 2560x1440 using a dual-link DVI adapter.  This is what I am currently using on my old 2008 Mac Pro.
    If i get a new model Mac Pro, could I continue this arrangement at the max resolution by using two Thunderbolt/Minidisplay port to Dual link DVI adapters (and, I assume, using two of the USB ports as I do now)?
    Frankly, I dont need the power of a new Mac Pro but my old one is long in the tooth.  I'd get a retina Macbook and use it as my desktop, but I cant think of any way to run both monitors at full resolution on the Macbook Pro.  I dont want to run them at HDMI resolution.
    Thanks in advance!

    Adapters go from $9 to $54, the latter having heat-sink which is not needed in an open cMP.
    Some support both as in either or but not two at the same time, SATA interface on the PCIe afapter, or an M.2 type
    While other PCIe "solutions" exist they are not OS independent or machine, the XP941 suffers from none of those concerns as it is bootable in all Mac Pro 1,1 thru 5,1, and is the only one for 200-7 models (and 2008 are iffy) so you can 'take it with you' if you move to a new cMP.
    Old controller, you need two SSDs in RAID0 to get 900MB/sec writes.
    Does not appear to be any of the real issues of PCIe slot and bus master, outside of you would exclude the 1x slot in the 2006 of course!
    The hardest part? getting these tiny M.2 blades, which are ~ 1" x 3.25" and have a tiny screw,  on the PCIe adapter.
    250GB SSD today are ~$120 + many do want SATA III PCIe (to get 550MB/sec and allow continued use of 4 x SATA II drive bays) runs ~$80-299. In some cases you then need a 2nd SSD. So if you want speed (vs size) then $240 + $100 and the $300 for XP941 256GB isn't bad.
    Finally, look for an Apple blade on ebay if running Yosemite - they vary, some are 2x (slow) M.2s and you want 4x but any are probably 700MB/sec and cost $400-700. No need with Apple part to worry about TRIM.
    Comparing 128GB SATA II $83 + $15 adapter vs PCIe XP941 128GB $140 + $24 is a 'toss-up' in cost but not performance, and one frees up drive bay and uses PCIe slot. (Generally 250GB are faster and better, the 128GB use to have 135MB/sec writes and $40 extras for 550MB and double storage makes sense, you never want an SSD to get down to 20% free, and you want to have 11% set aside for over-provisioning).
    So in a way you can get 1000MB/sec like nMP for $175-300 in any Mac Pro, and new faster blades are on the horizon offering 1400MB/sec.
    Kind of amazing, that M.2 support is in that old EFI all along waiting

  • Can't burn Dual Layer DVD-R on new Mac Pro?

    Can't burn Dual Layer DVD-R on new Mac Pro?
    I have a new Mac Pro with Pioneer DVD burner built in. I've since found out that it only burns Dual Layer +R type, and not the -R type.
    My replication company need a Dual Layer -R type DVD as they can't get a glass-master off the +R type Dual Layer discs.
    Can anyone recommend/suggest a cheap way of being able to either master off a DVD to Dual Layer -R disc, or perhaps copy my Dual Layer +R to a Dual Layer -R ?
    Thanks guys.

    Everything I have ever read about the DVD-R DL discs says the layer break can't be chosen by the author. It is not a DVDSP issue; it is an issue with the media.
    This is actually listed in the DVDSP 4.1 Late Breaking News on page 15:
    "Using DVD-R Dual-Layer Media
    If your system contains a DVD drive that can write to the new DVD-R dual-layer media, you can burn your DVD project to it with DVD Studio Pro. However, there are several issues:
    Since there is no current way for DVD Studio Pro to identify DVD-R dual-layer media as having two layers, burning a dual-layer project to it results in a warning appearing telling you that the DVD media may have insufficient room to hold the project. This message is based on the assumption that the disc is single layer. Both layers of the disc will be written to as needed, however, when you click Continue.
    If you are burning a dual-layer project, the break point you set will not affect where the layer break actually occurs. Instead, the first layer is written to until filled, at which point the drive switches to writing to the second layer.
    The switch between layers is a seamless layer change not supported by some DVD players, which may stop playing the disc when the switch point is reached.
    Important: Do not use DVD-R dual-layer media unless these issues do not impact your project.
    You can use DVD+R double-layer media for burning your dual-layer projects. With DVD+R double-layer media, DVD Studio Pro places the layer break point and sets the switch point to be nonseamless as specified in your project."
    Can you tell us what drive you have and what firmware (revision) it is?

  • Can i use imac's internal CD/DVD drive to install windows 8.1 pro on macbook via ethernet or firewire or other than purchasing an external drive??

    can i use imac's internal CD/DVD drive to install windows 8.1 pro on macbook via ethernet or firewire or any method other than purchasing an external drive??

    Note: These types of discs or activities are not supported by DVD or CD sharing:
    DVD movies.
    Audio CDs.
    Copy protected discs such as game discs.
    Install discs for an operating system such as Microsoft Windows (for use with Boot Camp), or Mac OS X.
    Burn a CD or DVD

  • I dropped my macbook pro and the screen is broken can i still use it with an external monitor? Or can I or how do I transfer hard drive files to my mac mini?

    I dropped my 17" macbook pro and the screen is broken. Can I still use it with an external monitor? When I plugged it into a monitor I had used it with before, I'm not able to see anything on the macbook screen to control it. It came on but I just got the blue screen with nothing else after typing in my password. (Didn't see the password form just assumed it was there somewhere and it did go from space to blue screen but no desktop icons, files, dock strip at top or anything else, just blank blue screen) so I can't access the system preferences.
    Or can I / or how do I, transfer hard drive files to my mac mini? If not salvageable as is can I pull out the hard drive and make it an external harddrive? In otherwords is anything salvageable? It seems it's coming on I just can't access anything. BTW I was told it would cost aprox $1000 to replace the screen! I paid almost $4000 for this thing and it was running great - makes me sick to lose it!

    I'd like to promise you that everything will be fine if you just get the monitor going - but it's hard to know what the hardware damage might be. It might be the monitor, or the damage might be greater.
    Your best solution would be visit your local Apple Store and let them know what your situation is. They have access to diagnostics you don't, and they might be able to the best way to save your data and keep you computing. It's still not covered, but they can tell you what your current options are.
    Um, you might consider investing in a backup drive.
    And there other repair options, too. Powerbook Medic http://www.powerbookmedic.com/xcart1/pages.php?pageid=67 offers reliable repairs, and quotes prices well under Apple's.

Maybe you are looking for

  • All webmail folders do not appear in my new imac mail

    how can i configure my mac mail so that all my web based email folders will be displayed there?

  • IMac crash

    As of today my iMac has started randomly crashing. The screen instantly goes black and the music I am listening to just keeps playing the same second of audio over and over until I reset. Is my hardware on the way out :S I can't afford a new mac at t

  • Could Oracle 10g (in a server)  work with existing Oracle 9i client

    Hello! I am new in Oracle, and I was wondering if it's possible to use Oracle 10g in a server with clients using Oracle 9i. Would that work? Are they compatible?. Thanks!

  • Mr11 and f.13

    Hi, I would like to know when to use F.13 and MR11. 1) Example 1, I need to use F.13 whereas example 2(whether due to quantity or amount), i need to use MR11. Correct? 2) Why minor differences in example 2 can happen? even it is due to forex, during

  • Blank Page at the end of the report

    Hi In my report i did not have any pagebreak or section break. But some times i am getting extra blank page at the bottom of the report . How to avoid this .. Thanks in Advance Have a Nice day.