Can I use non-native VLAN for AP management (BVI100 vs. BVI1)

Owning AIR-AP1121G-E-K9 and AIR-AP1131AG-E-K9, with IOS 12.3.8JA2, want to migrate AP (wired) management from native VLAN1 to tagged VLAN100.
Management VLAN must not be accessed by WiFi devices.
Tried to configure fa0.100, bridge 100 and BVI 100 instead of fa0.1, bridge 0.1 and BVI1, reloaded and AP is working, but doesn't respond to management.
Tried to use simple L3 fa0.1, but int is not reachable from outside.
Any suggestions?
Thank you very much
Flavio Molinelli
[email protected]

The management VLAN must be the Native VLAN ... it doesn't have to be VLAN 1, but whichever VLAN you declare as Native will be the Management VLAN (at least as far as the AP is concerned) ...
Some switches / routers permit the management and Native VLANs to be different ... verify that both are configured and matching on both ends (AP and switch / router).
Good Luck
Scott

Similar Messages

  • Problems with associating with SSIDs using non-native VLANs

    Hello
    I have bought 2 Aironet 1300 that I intend to use as root-bridge and nonroot-bridge to a remote location. The plan is to have a trunk with 3-4 vlans.
    From what I have understood the way to do trunking on these is to set up 1 vlan to 1 ssid, up to a total of 16 vlans/SSIDs.
    I have now set up 2 vlans with one SSID each, with WEP encryption, and open/mac auth. 1 vlan is native.
    And now to the problem. If I have both SSIDs, the nonroot bridge wont associate, getting the error: "Interface Dot11Radio0, cannot associate: Rcvd response from xxxx.xxxx.xxxx". If I remove the SSID with the native vlan, I get the same error. If I remove the ssid with the nonnative vlan (keep the ssid with the native vlan) they associate just fine.
    So the question I am stuck on, is why wont it associate when i use SSIDs with non native vlans?

    I have come across this problem once before, you have to set one of the SSID's as the infrastructure SSID - this is the SSID that the AP's will associate over.
    Try setting one of them to the infrastrucuture SSID.
    "nfrastructure-ssid [optional]
    (Optional) Designate the SSID as the SSID that other access points and workgroup bridges use to associate to this access point. If you do not designate an SSID as the infrastructure SSID, infrastructure devices can associate to the access point using any SSID. If you designate an SSID as the infrastructure SSID, infrastructure devices must associate to the access point using that SSID unless you also enter the optional keyword. " taken from:-
    http://www.cisco.com/en/US/docs/wireless/access_point/12.2_15_JA/configuration/guide/s15ssid.html
    HTH.

  • Native vlan for a 3550XL swtich

    hello
    i have the follow dilemma. a 3550XL has a voice vlan 10 , a data vlan 20 and an management vlan 99. assinging the vlan 10 as native wil remove its tagg across the trunk ports. also cisco recomends native vlan not be the same as management vlan . but when i made the vlan 99 the vlan 1 goes in shutdown situation . so what is the best practice about tha native vlan into a voice switch ?
    thanks

    IEEE 802.1Q Configuration Considerations
    IEEE 802.1Q trunks impose these limitations on a network:
    In a network of Cisco switches connected through IEEE 802.1Q trunks, the switches maintain one instance of spanning tree for each VLAN allowed on the trunks. Non-Cisco devices might support one spanning-tree instance for all VLANs.
    When you connect a Cisco switch to a non-Cisco device through an IEEE 802.1Q trunk, the Cisco switch combines the spanning-tree instance of the VLAN of the trunk with the spanning-tree instance of the non-Cisco IEEE 802.1Q switch. However, spanning-tree information for each VLAN is maintained by Cisco switches separated by a cloud of non-Cisco IEEE 802.1Q switches. The non-Cisco IEEE 802.1Q cloud separating the Cisco switches is treated as a single trunk link between the switches.
    Make sure the native VLAN for an IEEE 802.1Q trunk is the same on both ends of the trunk link. If the native VLAN on one end of the trunk is different from the native VLAN on the other end, spanning-tree loops might result.
    Disabling spanning tree on the native VLAN of an IEEE 802.1Q trunk without disabling spanning tree on every VLAN in the network can potentially cause spanning-tree loops. We recommend that you leave spanning tree enabled on the native VLAN of an IEEE 802.1Q trunk or disable spanning tree on every VLAN in the network. Make sure your network is loop-free before disabling spanning tree.
    http://www.cisco.com/en/US/docs/switches/lan/catalyst3550/software/release/12.2_25_sec/configuration/guide/swvlan.html

  • Can I use non-apple notebook to connect AirPort Extreme?

    I
    Can I use non-apple notebook to connect AirPort Extreme?

    He might be trying to do so to promote his products or may be there was some misunderstanding.
    Airport Extreme will work as a wireless router supporting upto 50 systems including Mac computers, PCs, iPad, iPhone, iPod touch, Apple TV and virtually all 802.11a/b/g/n Wi-Fi wireless devices — all at the same time.
    for reference http://store.apple.com/us/product/MD031LL/A/AirPort-Extreme

  • How can I use srvctl command line for change "Failover type" and "F method"

    Hi all,
    I am using Oracle One Node (11.2.0.3), and I have a service:
    /u01/11.2.0/grid/bin/srvctl config service -d orcl
    Service name: orcldb
    Service is enabled
    Server pool: orcl
    Cardinality: 1
    Disconnect: false
    Service role: PRIMARY
    Management policy: AUTOMATIC
    DTP transaction: false
    AQ HA notifications: false
    Failover type: NONE
    Failover method: NONE
    TAF failover retries: 0
    TAF failover delay: 0
    Connection Load Balancing Goal: LONG
    Runtime Load Balancing Goal: NONE
    TAF policy specification: BASIC
    Edition:
    Preferred instances: orcl_1
    Available instances:
    I would like to change "Failover type" and "Failover method" to:
    Failover type: SELECT
    Failover method: BASIC
    How can I do that? Is there any graphical tool for it? Or, How can I use srvctl command line for change it?
    Thanks in advance.
    Leonardo.

    user10674190 wrote:
    Hi all,
    I am using Oracle One Node (11.2.0.3), and I have a service:
    /u01/11.2.0/grid/bin/srvctl config service -d orcl
    Service name: orcldb
    Service is enabled
    Server pool: orcl
    Cardinality: 1
    Disconnect: false
    Service role: PRIMARY
    Management policy: AUTOMATIC
    DTP transaction: false
    AQ HA notifications: false
    Failover type: NONE
    Failover method: NONE
    TAF failover retries: 0
    TAF failover delay: 0
    Connection Load Balancing Goal: LONG
    Runtime Load Balancing Goal: NONE
    TAF policy specification: BASIC
    Edition:
    Preferred instances: orcl_1
    Available instances:
    I would like to change "Failover type" and "Failover method" to:
    Failover type: SELECT
    Failover method: BASIC
    How can I do that? Is there any graphical tool for it? Or, How can I use srvctl command line for change it?
    Thanks in advance.
    Leonardo.srvctl modify service -d database_name -s orcldb -q TRUE -m BASIC -P BASIC -e SELECT -z 180 -w 5 -j LONG
    Also see
    11gR2(11.2) RAC TAF Configuration for Admin and Policy Managed Databases [ID 1312749.1]

  • Can i use free VMWare ESXi for commercial use.?

    Hi,
    I know that this question have come up before but I can't find any
    definitive answers. Can i use free VMWare ESXi for commercial use. We
    would like to host
    several customers on a machine running  VMWare ESXi. I want a clear answer so we can do it without any further discussion.
    Thank you all in advance,
    LNN

    If you plan on renting out a VM, then you need to look at the hosting programs - http://www.vmware.com/solutions/hosting/index.html.   The base EULA for ESX and ESXi do not allow for the rental of VMs but I believe it may be possible to get an exemption to that.
    http://communities.vmware.com/message/1016993#1016993
    VMware grants you a nonexclusive, non-transferable license, without rights to sublicense, to  install or have installed a single instance of the Software and each Licensed Additional Module on a single Server, unless permitted to have multiple instances on a single Server or to have multiple instances on multiple Servers by the payment of applicable license fees (whether such fees are based on a per Processor, a per Virtual Machine, a per user or any other VMware approved licensing model); (ii) use the Software and each Licensed Additional Module solely for information processing and computing purposes, including the hosting of computer application-based services from a Virtual Machine and provision of such services via an internal or external network, provided such services may not consist of services to a third party that provide primarily computing or processing power (such as utility computing or grid computing) or any computer application-based service that is traded, rented, leased or sold on a Virtual Machine basis; and (iii) use and reproduce the VMware Virtual Infrastructure Client Software or VMware WebAccess (in object code form only) for the purposes of installation and operation on an unlimited number of your own internal computers or terminals solely for the purpose of accessing the Server on which the Software is installed.

  • When will apple begin to use non us banks for apple pay?

    when will apple begin to use non us banks for apple pay?

    Apple have not announced any dates for non-US rollout of Apple Pay as yet. They have to negotiate agreements with local banks and local branches of credit card companies in multiple countries, ensure they are in compliance with local laws and many other things before this can happen. It is going to take months at the very least I'd guess before you will see it even in major EU countries and longer for places like Asia and the Middle East. It will probably be rolled out in stages over the next year or two (or more) until most of the world has Apple Pay available.
    It took 2+ years after its US debut for iTunes Music Store to spread to many other nations, and the video store was about 12-18 months plus as I recall. Apple Pay probably makes those negotiations look simple in comparison.

  • HT204053 i RECENTLY PURCHASED ANOTHER IPHONE.  MY INTERNET IS NOT WORKING.  I JUST CREATED AN APPLE ID.  WHAT'S NEXT?  I NOW HAVE TWO DIFFERENT ACCOUNTS WITH DIFFERENT USER NAMES.  HOW CAN I USE ONLY ONE ACCOUNT FOR ITUNES, ICLOUD APPLE ID ETC???

    I RECENTLY PURCHASED ANOTHER IPHONE.  MY INTERNET IS NOT WORKING.  I JUST CREATED AN APPLE ID.  WHAT'S NEXT?  I NOW HAVE TWO DIFFERENT ACCOUNTS WITH DIFFERENT USER NAMES.  HOW CAN I USE ONLY ONE ACCOUNT FOR ITUNES, ICLOUD APPLE ID ETC???

    Welcome to the Apple community.
    iTunes and iCloud and different accounts, you will need to delete both accounts from your device before adding the new details in their place.
    For iCloud go to settings > iCloud, scroll down and hit the delete button. You can then sign back in using your correct details. For iTunes go to settings >store, tap your account ID and then sign out, you can then sign back in using your correct Apple ID.

  • HT204053 Can I use one Apple ID for two Apple IPhones?

    Can I use one Apple ID for two Apple IPhones? I received an answer of yes.
    Now another question.  I have one ICloud Account, Two IPhones.  Can I use Find my IPhone via the one ICloud Account?  Can I see two IPhones on the map at the same time?  or do I need to view the second phone via some other method.
    Message was edited by: Hunter3D

    Yes.
    Cheers,
    GB

  • HT4436 My family has multiple iPhones.  Can we use one Apple ID for all of our phones?

    My family has multiple iPhones.  Can we use one Apple ID for all of our phones?

    If you use the same AppleID for iMessage and iCloud though, you will all be sharing the same message account and iCloud email account.  You can use a common AppleID for purchased content, but each create your own unique AppleID for iMessage and iCloud so you each have your own private accounts for those services.

  • How do we use if statement in labview?moreover can i use if statement inside for loop?

    how do we use if statement in labview?moreover can i use if statement inside for loop?

    The if statement in LabVIEW is the Case structure. You can find that on the Structures palette right next to the For Loop. If you're still on the same subject about terminating a for loop early, then what you do is enclose your functions inside the loop with a case statment and make one of the case's empty except for one or more constants that you might have to wire. Hopefully, the attached picture will explain what I mean. Also, as I mentioned in one of your other posts, I think this technique is not as good as using a while loop. The array in the attached example is the same size no matter what and you may have to handle stripping extra or invalid elements.
    Attachments:
    For_Loop_with_Case.jpg ‏21 KB

  • How many lines we can print using Non-alv report list ?

    Hi Experts,
    How many lines we can print using Non-alv report list ?
    regards
    vishnu

    Hi,
    It depends on the page size according to the page size we can set the no. of lines as follows,
    REPORT  program_name   NO STANDARD PAGE HEADING
    LINE-SIZE 290
    LINE-COUNT 65.
    Hope it helps you,
    Regards,
    Abhijit G. Borkar

  • Can I use one itunes account for multiple users and multiple devices

    Can I use one itunes account for multiple users and multiple devices?

    The iTunes EULA, as I understand it (I'm not an attorney )for Apps is basically that one person can use an App multiple devices, or multiple people can use an App one device..so one to many or many to one, but not many to many....

  • Can we use same program ID for more than one RFC scenarios

    Hi experts,
                I am working on a RFC to FILE scenario. I have created one TCP/IP connection in SM59 with a program ID. Can we use this program ID for more than one scenario. I have written code as below
    data: iquote type standard table of ZIQMD initial size 0,
          IPRODUCT type standard table of ZPMS initial size 0,
          wa_quote type ZIQMD,
          wa_PRODUCT type ZPMS.
    CALL FUNCTION 'Z_CBT_RFC_QUOTEMASTER'
      TABLES
        I_QUOTE       = iquote          .
    CALL FUNCTION 'Z_CBT_RFC_QUOTEMASTER' in background task DESTINATION
    'ID4'
      TABLES
        I_QUOTE       = iquote          .
      COMMIT WORK.
    CALL FUNCTION 'Z_CBT_RFC_PRODUCTMASTER'
      TABLES
        IPRODUCT       = IPRODUCT          .
    CALL FUNCTION 'Z_CBT_RFC_PRODUCTMASTER' in background task DESTINATION
    'ID4'
      TABLES
        IPRODUCT       = IPRODUCT          .
        COMMIT WORK.
    when i am executing the code like this. i am able to send the data to 'Z_CBT_RFC_QUOTEMASTER'  , but iam not getting data  for 'Z_CBT_RFC_PRODUCTMASTER'  interface. ID4 is the connection that i have created in SM59. with program ID as ABCD.
                  Can i use the same connection for all interfaces.Please help in this, if we can use same connection for all interfaces. then how to make changes in XI.
    Thanks in advance.
    Thanks & Regards,
    Poorna.

    Just tried this and I can confirm that my earlier understanding was correct!
    One of my colleagues confused me out and the conclusion is,
    1. You need a separate TCP IP Connection for every interface with a Unique program ID.
    Regards
    Bhavesh

  • How can I use my itunes library for iphoto slideshow?

    how can I use my itunes library for iphoto slideshow?

    Here's a possible workaround:
    Create the slideshow in Iphoto and add a theme and music.
    Install Picasa  and it will include the slideshow on it's indexed list.
    Upload the slideshow to PicasaWebAlbums and send the link to anyone you wish.
    The music and theme is preserved.
    Caveat: My playback pictures appear darker than usual but that could be just lousy photography...:)
    Example:https://picasaweb.google.com/mb2180/Kona2011?authuser=0&authkey=Gv1sRgCPGWz_qPrM XKZA&feat=directlink

Maybe you are looking for