Can I use SRST for multiple sites wit separate 911 lines

Is it possible to use an SRST (like a 2911 CME/SRST) to support multiple sites. 
We have two sites next door to each other. They are connected by fiber with Cisco switches (vlans) at box sites.
Can I use a single SRST and have two separate 911 POTS lines setup so that each site has it's own unique 911 associated with it?
I can create two separate Voice vlans for the two sites and I could have both 29xx interfaces in use (one for each VLAN), but can I separate the dialing out function so that each vlan uses a unique POTS line this way?
Any other solutions other than two SRSTs?

We have to keep the 911 dialing the same at all sites since I already had an idea like that ...but we use 911, 9911 and 8911 for everyone to reach 911 so that they are not confused during an outage.
We will just have to bite the bullet and order 2901 SRSTs for all our small remote sites. 

Similar Messages

  • Using SPSiteDataQuery for multiple Site Collections

    Hi All,
    I would like to query five contact lists on multiple site collections. I can query the lists using SPSiteDataQuery if they are within the same site collection, but I can not query the lists over multiple site collections.
    Is there a method like SPSiteDataQuery that I can use to query lists over multiple Site Collections?
    Many Thanks,
    Colin

    Hi,
    As you have mentioned that: SPSiteDataQuery which can query multiple webs within the same site collection, but not across multiple site collections. You can't accomplish that easily.
    The solution evolves from first using the SPSiteDataQuery class to run a query upon each site collection and then aggregating the results.
    For detailed information, refer to the following article:
    https://oidatsmyleg.wordpress.com/2009/08/13/cross-site-collection-query-almost/
    Besides, here is a similar requirement post, you can take a look at:
    http://sharepoint.stackexchange.com/questions/114329/accessing-list-data-in-multiple-site-collections
    Best Regards,
    Lisa Chen
    TechNet Community Support
    Please remember to mark the replies as answers if they help, and unmark the answers if they provide no help. If you have feedback for TechNet Support, contact
    [email protected]

  • Can I use FCX for multiple users on the same machine?

    I have one mac pro, and two video cmpanies. I have two users on my machine and would like to set up two different final cut x workplatforms. Is that possible?

    Of course, you can use FCP X from two different user accounts on your machine. The question here, I believe, is how to separate the content that each user accesses.
    One obvious way to achieve that would be to store the content in the system disk - that would put events and projects in each user's Movies folder. But that is a bad option, for performance reasons, and more.
    You could have separate external disks for each user to store his content.
    Also, you could use different disk images which could, say, be all stored in the same internal (but not system) drive.

  • Can bookmarks be protable for multiple computers? Is it an option to log on and use my bookmarks with multiple computers and locations? Thanks

    Can bookmarks be protable for multiple computers? Is it an option to log on and use my bookmarks with multiple computers and locations? Thanks

    Profile is a folder which store all your personal data in a safe place
    * https://support.mozilla.com/en-US/kb/Profiles
    You can use this button to go to the current Firefox profile folder:
    * Help > Troubleshooting Information > Profile Directory: Open Containing Folder
    here explain how to backup profile
    * https://support.mozilla.com/en-US/kb/Backing%20up%20your%20information
    Here explain how to restore it
    *https://support.mozilla.com/en-US/kb/Recovering%20important%20data%20from%20an%20old%20profile

  • How to send right CallingNumber when Cisco CER is down for multiple sites

    Hi,
    Cisco ER 7.x system with centerized CUCM 7.1(x) cluster for multiple sites over WAN, where each site has local voice gateway (MGCP) with T1/PRI connected. All the phones are DIDs.
    When considering 911 calls redundancy when CER is down, Cisco ER administration guide recommends using Local Route Group for 10911 or something else route-pattern on CUCM which is used:
    http://www.cisco.com/en/US/partner/docs/voice_ip_comm/cer/7_1_1/english/administration/guide/e911plan.html#wp1062106
    To configure LRG, follow these steps:
    1. On Cisco Unified Communications Manager Administration, configure the LRG route pattern and route point for 911 emergency call routing.
    2. On Cisco Unified Communications Manager Administration, configure any destination route point that is being forwarded in the emergency call route point with the LRG route pattern.
    3. On Cisco ER Administration, configure the LRG route pattern as the default ERL.
    My question is:
    On the 10911 route-pattern using LRG, how can configure the each site ELIN number as the calling number on the route-pattern which is normally assigned on E911 partition only? or do I need change MGCP to H.323 in order to achieve this purpose?
    Do I miss something?
    Thanks,
    JJ

    Hi,
    I am not sure with in obiee it is possible? But third party tool we can do it.
    Site scope monitor tool is there, what this tool will do it will send the alert mail to respective team whenever services are down.
    For more information google it? You can get better idea.
    Thanks,
    Satya

  • LDAP design question for multiple sites

    LDAP design question for multiple sites
    I'm planning to implement the Sun Java System Directory Server 5.2 2005Q1 for replacing the NIS.
    Currently we have 3 sites with different NIS domains.
    Since the NFS over the WAN connection is very unreliable, I would like to implement as follows:
    1. 3 LDAP servers + replica for each sites.
    2. Single username and password for every end user cross those 3 sites.
    3. Different auto_master, auto_home and auto_local maps for three sites. So when user login to different site, the password is the same but the home directory is different (local).
    So the questions are
    1. Should I need to have 3 domains for LDAP?
    2. If yes for question 1, then how can I keep the username password sync for three domains? If no for question 1, then what is the DIT (Directory Infrastructure Tree) or directory structure I should use?
    3. How to make auto map work on LDAP as well as mount local home directory?
    I really appreciate that some LDAP experta can light me up on this project.

    Thanks for your information.
    My current environment has 3 sites with 3 different NIS domainname: SiteA: A.com, SiteB:B.A.com, SiteC:C.A.com (A.com is our company domainname).
    So everytime I add a new user account and I need to create on three NIS domains separately. Also, the password is out of sync if user change the password on one site.
    I would like to migrate NIS to LDAP.
    I want to have single username and password for each user on 3 sites. However, the home directory is on local NFS filer.
    Say for userA, his home directory is /user/userA in passwd file/map. On location X, his home directory will mount FilerX:/vol/user/userA,
    On location Y, userA's home directory will mount FilerY:/vol/user/userA.
    So the mount drive is determined by auto_user map in NIS.
    In other words, there will be 3 different auto_user maps in 3 different LDAP servers.
    So userA login hostX in location X will mount home directory on local FilerX, and login hostY in location Y will mount home directory on local FilerY.
    But the username and password will be the same on three sites.
    That'd my goal.
    Some LDAP expert suggest me the MMR (Multiple-Master-Replication). But I still no quite sure how to do MMR.
    It would be appreciated if some LDAP guru can give me some guideline at start point.
    Best wishes

  • Iweb 09_good for multiple site designs

    Hi!
    I am looking to upgrade to a better imac and iWeb 09 to create "microsites" for my current print design clients to help expand their marketing. Is this version of iWeb easy to use for that or does it to multiple sites at all? Basically I am asking is this version a good one for multiple site building? Ease of use for that purpose? Thanks!

    Welcome to the Apple Discussions. iWeb 09 can handle multiple sites quite easily. However, a lot depends on where you plan to host the sites and manage them. Will they each have a domain name for the site?
    On MobileMe you can have only one site with CNAME domain name forwarding to the same account. The others must use the standard html URL forwarding. AND they all must be created in the same Domain.sites2 file. That can be a problem.
    If you use the standard domain name forwarding with MMe for all the sites then you can have a separate domain file for each client and use Web Site Maestro to manage then them and select which one to open and work on.
    If each client will provide their own hosting server then it's possible that CNAME forwarding can be used for each client if they have a domain name and their server supports CNAME.
    I use iWebSites to manage over 75 individual sites. It lets me create multiple sites and multiple domain files.
    This lets me edit several sites and only republish the one I want.
    OT

  • I'm an American living on a timed (though long-term) assignment in Ireland. I have both American and Irish bank accounts and addresses. I have two Qs. 1. Can I use the US Adobe site when in Ireland? Or will my physical location prevent me from doing so? 2

    I'm an American living on a timed (though long-term) assignment in Ireland. I have both American and Irish bank accounts and addresses. I have two Qs. 1. Can I use the US Adobe site when in Ireland? Or will my physical location prevent me from doing so? 2. I am working for a not-for-profit organization. Is there a special pricing plan for non-profits, similar to the plans for students, small business, etc? Thanks for whatever help you can give me. (P.S. As a potential customer and past user of Adobe products for 15  years, I find it INCREDIBLY FRUSTRATING that I cannot speak with any Adobe representative, but am continually re-routed instead to a public forum to get what I hope will be accurate information. Not good, Adobe. Your products are amazing. Your customer service leaves a lot to be desired. I don't mean that with disrespect, but as honest feedback.)

    Hi bookchic
    Thanks for your feedback.
    Non-profit pricing is available to eligible institutions via the VIP program which is sold by resellers - see Eligibility guide
    For details of resellers please check here: Adobe Platinum Partners – Value Incentive Plan
    If you wish to purchase an individual plan via Adobe.com the country of your Adobe ID will determine which site you order from.
    Kind regards
    Bev

  • I am using MS Office 2010 and Windows XP Professional, can I use iCloud for backup of my files and documents?

    I am using MS Office 2010 and Windows XP Professional, can I use iCloud for backup of my files and documents? I am planning to transition to a Mac so using the iCloud seems to make the most sence.

    No, it is not a backup method at all.  If you delete a sync'd file on any device, you delete it permanently from iCloud.  That by its very essence is not a backup solution therefore.  A backup solution does not automatically and simultaneiously delete the file everywhere when it is deleted from the original source.
    iCloud is strictly a syncronization tool for using files on multiple internet connected devices.

  • Creating a PO Using BAPI For Multiple PLants Or Multiple Line Items

    Hi All
        Can you please suggest me how to create a Purchase Order Using BAPI_PO_Create1 for Multiple Plants Or for Multiple Line items. The Requirement is like the PO is for single material for single vendor but for mulple stores i.e plants
    NOte:  Suggest me the  Creation of PO for MUltiple Line items or for multiple plants Using BAPI . Hope you people will give me the needful.
    Regards
    Shivakumar Bandari

    Hi,
    Here is the sample code to do that...
    *---> po header data
      wa_poheader-vendor    =  your vendor..
      wa_poheader-doc_type  =  Your doc type..check with Functional contact....
      wa_poheader-purch_org =  Purchasing Org..
      wa_poheader-pur_group =  Purchasing Group
    *---> po header data (change toolbar)
      wa_poheaderx-vendor    =  'X'.
      wa_poheaderx-doc_type  =  'X'.
      wa_poheaderx-purch_org =  'X'.
      wa_poheaderx-pur_group =  'X'.
    *---> poitem data
    data: item like ekpo-ebelp.
    item = '0010'.
    loop at t_parts.
      it_poitem-po_item  =  '00010'.
      IT_POITEM-PLANT    =  Plant..
      IT_POITEM-STGE_LOC =  Sloc...
    *---> poitemx (item data change toolbar)
      it_poitemx-po_item  =  '0010'.
      it_poitemx-po_itemx  =  'X'.
      IT_POITEMX-PLANT    =  'X'.
      IT_POITEMX-STGE_LOC =  'X'.
    *---> add record's to internal table
      APPEND:  it_poitem,
             it_poitemx.
    endloop.
    *call bapi_po_create1
      CLEAR v_ebeln.
      CALL FUNCTION 'BAPI_PO_CREATE1'
        EXPORTING
          poheader         = wa_poheader
          poheaderx        = wa_poheaderx
        IMPORTING
          exppurchaseorder = v_ebeln
        TABLES
          return           = it_return
          poitem           = it_poitem
          poitemx          = it_poitemx.
    *---> check the return table for error message
      READ TABLE it_return WITH KEY type = 'E'.
      IF sy-subrc NE 0.
        CALL FUNCTION 'BAPI_TRANSACTION_COMMIT'
          EXPORTING
            wait = 'X'.
      endif.
    Thanks,
    Murali

  • IPv6 deployment problem for multiple site

    Dear Expert,
    I have a question about the deployment of IPv6 on two different site and the requirement is that client may need to auto switchover to another site while one of the ASR1002 is failure. I have using two different prefix on two sites with IPv6 stateless autoconfig like above diagram. Different prefix used for each site due to each site should use there own IPv6 prefix for Firewall Stateful(Default gateway point to local site firewall only). Client will retrieved two IPv6 addresses at the same time and it seems workable on Vista PC and Mac(Mac haven't select the High DRP one but work fine) and I haven’t try for other mobile device (have WiFi device for vlan100). Is it a valid solution? Any other solution for multiple site deploy IPv6 with Firewall no NAT enabled?
    Thank you very much!
    Regards,
    Kawaii

    One option would be to tweak the OS prefix policy table to prefer v4 to v6.  On Linux this is in /etc/gai.conf; on windows you'd run "netsh interface ipv6 set prefixpolicies ...".  The side effect would be that you'd only do v6 with the v6-only sites, not with the dual-stack sites.

  • Since using cloudflare for my site I'm having troubles with Firefox cache

    Hello,
    Since I'm using CloudFlare for my Site I'm having a weird trouble occurring only with Firefox (version 16.0.2 / Mac OsX.6.8), but not with Chrome or Safari.
    When I navigate from the main page of my Wordpress Site to a single post, then back to the main page, then to another single post and back again to the main page, the browser displays a binary file instead of the normal page. After emptying Firefox cache the page loads again properly.
    When I pause CloudFlare the trouble disappears.
    I just ask here because this does not happen with other browsers.
    The config of the site is : Wordpress 3.4.2 with W3 Total Cache Plugin and the browser caching enabled.
    If disabling the plugins the problem remains the same.
    Thanks in advance to anyone who could help.

    Hi,
    This is not a solution but one way you could try to troubleshoot this is through the [https://developer.mozilla.org/en-US/docs/Tools/Web_Console Web Console] opened via '''Tools''' ('''Alt''' + '''T''') > '''Web Developer'''. You need to have it open before loading/reloading etc. Clicking on GET, POST links provides detailed info including Content-Type, encoding etc. You can also right-click and select '''Log Request and Response Bodies''' to view the transferred data. Hopefully you would be able to find the cause and resolve it.
    [https://developer.mozilla.org/en-US/docs/Tools Firefox Tools]

  • Can w use rsync for Business Continuity for Oracle Applications Release12 ?

    Hi ,
    One of our customer has implemented Oracle EBS R12 (12.0.6) on HP-UX (IA).
    Database Tier on a Two Node Oracle Database 10g R2 RAC
    Application Tier on Two Node using Shared APPL_TOP with Load Balancer.
    They want to implement DR site using Oracle Data Guard (RAC to Non-RAC).
    I was referring to Note: 452056.1 +( Business Continuity for Oracle Applications Release 12 on Database Release 10gR2 - Single Instance and RAC )+.
    In this note its mentioned that:
    If you wish to synchronize your concurrent manager log and out files between production and standby, you need to create folders matching to the APPLCSF environment variables for each others......................... For example, set up an rsync job similar to the below example in cron, to run every few minutes.
    Can we use rsync for Production systems without any issues? Customer is concerned about using freeware on their Production systems.
    Rgds,
    Thiru.

    Thiru,
    Can we use rsync for Production systems without any issues? Customer is concerned about using freeware on their Production systems.You can use it with no issues. Or, you could use any other copy tool to copy those files.
    Thanks,
    Hussein

  • AP Payment for multiple sites

    Is there a way to pay more than one site for a supplier in the same payment?

    Hello All,
    Any solution for this situation ? We are on R12 and we would like to pay single payment for multiple sites for same supplier. Anyone has any idea how do we go about this ?
    Thanks in Advance
    Dinesh
    Edited by: Dinesh Chauhan on 11-May-2010 01:15

  • How can I use TopLink for querys that have two and more tables?

    I use TopLink today, and I can use one table to query, but how can I use TopLink for querys that have two and more tables?
    Thank you for see and answer this question.

    You can write a custom SQL query and map it to an object as needed. You can also use the Toplink query language "anyOf" or "get" commands to map two tables as long as you map them as one to one (get command) or one to many (anyOf command) in the toplink mapping workbench.
    Zev.
    check out oracle.toplink.expressions.Expression in the 10.1.3 API

Maybe you are looking for