Can I use the connection capacity of FMIS to estimate the FMS Enterprise?

Hi,
Can I use the capacity of FMIS to estimate the maximum connection of FMS Enterprise?
Even bandwidth and latency of RTMFP are minimum. FMS Enterprise may still need to monitor each peer when using RTMFP connections.
So can I use the connection capacity of FMIS to estimate the FMS Enterprise?
Thanks.
Joseph

Bryan,
Smokerz was suggesting that you temporarily bring the Express upstairs, connect it & configure it, and then take it back down stairs again.
As for your desired setup:
Actually, if configured correctly, your Time Capsule should the source of your network and the Express should be the devise joining/extending it. This is the way I have it set up. However, you seem to want to configure it the other way around. Not very practical.
Take a look at the following thread for a discussion on this:
http://discussions.apple.com/click.jspa?searchID=-1&messageID=7997922
Particularly note the lengthy step-by-step provided by Tesserax.
Hope this helps

Similar Messages

Can i use the same socket to connect to more than one servers

hi,
I'm new to java. I want to know whether a socket created using Socket() constructor can be used to connect to multiple servers, not necessarily at a particular point of time. ie, i want to connect to various servers using a single socket and register some info abt them, possible using a loop, one by one. I use connect() method to connect to particular server.
In other words is Socket class is mutable.
Edited by: itsraja on Feb 25, 2008 5:50 AM

In short, I don't think so.
Setting the server name for a socket is in the constructor.
Socket s = new Socket("localhost", 501);I don't believe that there are any functions, such as:
s.setHost("localhost");
s.setPort(501);However, JavaDocs suggests that when you use the no-args constructor, your class becomes an automatic SocketImpl class, but you can't reach any of its variables unless you derive from the class, itself. But that's probably a bigger headache than it's worth.
Now TECHNICALY, if you didn't want to create a new variable, you could use:
Socket s = new Socket("localhost", 501);
s.close();
s = new Socket("remotehost", 502);
s.close();However, this is still creating a new instance and thus a new object in memory.
I hope this answers your question.
Let us know exactly what you're trying to do for a more exact answer.
~Derek

Wifi problems. I am using my ipad connected to a secure server. I keep having connection problems. My ipad shows I am connected, but I can't use the internet at all. I keep getting a not connected message. Help

I am using my ipad on a secure network. I have problems staying connected. It shows I'm connected with full bars but I can't use the internet. I turn the wireless off, reset the network and turned off the ipad, but this problem keeps happening. (Its been going on about 2 weeks) Any ideas?

Sayingyou went through all the steps of fixing provides us with little information see we do not know what step you tried.
- Have you reset your iPod:
Reset iPod touch: Press and hold the On/Off Sleep/Wake button and the Home
button at the same time for at least ten seconds, until the Apple logo appears.
- Powered off and then back on your router?
- The troubleshooting here:
iPhone and iPod touch: Troubleshooting Wi-Fi networks and connections-
- Configuring your router to use no encryption as a test. If OK, the try a simple password.

Can I use the HDMI out on a HP ALL IN ONE TOUCHSCREEN Desktop to connect a second monitor with HDMI

Can I use the HDMI out on a HP ALL IN ONE TOUCHSCREEN Desktop to connect a second monitor with HDMI in without any additional software or graphics adaptor. I have a 520-1070
HP - 23" Touch-Screen TouchSmart All-In-One Computer - 8GB Memory - 2TB Hard Drive ? I used a HDMI to HDMI cable and the monitor was not recognized.

Here are the specs for your HP TouchSmart 520-1070 Desktop Computer. As previously stated your computer Doesn't have a HDMI output, instead it has a HDMI input. This is designed to let you connect a game console, a DVD/Bluray player, etc. to use as a monitor.
If you wish to conect a second monitor to your computer, you will need to use a USB-to-video adapter such as the EVGA UV Plus+ UV39 or EVGA UV Plus+ UV19. Using an adapter like these with the touch feature of your computer may cause issues with pointer control and you may need to disable the touch feature to use "extended desktop".
Frank
{------------ Please click the "White Kudos" Thumbs Up to say THANKS for helping.
Please click the "Accept As Solution" on my post, if my assistance has solved your issue. ------------V
This is a user supported forum. I am a volunteer and I don't work for HP.
HP 15t-j100 (on loan from HP)
HP 13 Split x2 (on loan from HP)
HP Slate8 Pro (on loan from HP)
HP a1632x - Windows 7, 4GB RAM, AMD Radeon HD 6450
HP p6130y - Windows 7, 8GB RAM, AMD Radeon HD 6450
HP p6320y - Windows 7, 8GB RAM, NVIDIA GT 240
HP p7-1026 - Windows 7, 6GB RAM, AMD Radeon HD 6450
HP p6787c - Windows 7, 8GB RAM, NVIDIA GT 240

Need to connect to upgraded Oracle EBS R12 version from R11. The current ODI set up is pointing to R11, Can i use the same connection to point to R12? Please hele experts..

Need to connect to upgraded Oracle EBS R12 version from R11. The current ODI set up is pointing to R11, Can i use the same connection to point to R12? Please hele experts...
Rp

1. in physical connections part can i use the same work schema
2. Can i use same contexts created or do i need to create everything as new and then try?
Thanks,
Rp.
Hi,
As you mentioned that you just upgraded the database, so the data is same and schema is same you can connect with the same work schema.
Yes, you can use the same contexts , but need to do Reverse Engineering for your new database.
And about data server, i think you also have no need to create new data server, if hostname,sid and port etc are same as these were with R11(consult with your DBAs regarding it)

Can I use the Airport Express to connect to a Linksys Wireless Network and then use the Ethernet port on the Airport for a wired connection to a device for internet access? Would I be able to then also use that Ethernet pt to a Ntwk Hub for more wired c

Thanks for the help. Looked but not clear on what I am trying to do as being possible. Can I use an Airport Express to connect wireless to a Linksys Wireless Router, such that I can then use the Ethernet ports on the Airport to either connected to a PC wired, or even use a hub off the Airport Express to allow multiple wired connections to it?
I am not looking to have the Airport Express extend my wireless network, just connect to it and provide me wired connections in a different location from where my Linksys Route is located. Would prefer to replace Linksys with all Apple, but just not possible financially yet. Thanks for the help.

If the AirPort Express Base Station (AX) is an 802.11n model, then yes, you can reconfigure it as a wireless Ethernet bridge. In this configuration, the AX would join the wireless network provided by the Linksys router and its Ethernet port would be enabled for either a single wired device or for an Ethernet hub or switch for multiple devices.

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use?

I have an airport extreme and express, if I use the extreme as a base station connected to my old router can I use the express to extend the signal while also creating a new network that only I can use? Essentially having two wifi connection off the same network? If so how do I set this up?

Extending using a wireless connection always results in a performance compromise.
If the Express is going to extend using a wireless connection, then the Express will need to be located about half way between the AirPort Extreme and the general area where you need more wireless coverage. The more that you have line-of-sight between the Extreme and Express, the better the network will operate.
Remember......the Express can only "extend" the quality and signal speed that it receives, so it needs to be located where it can get a very good signal from the Extreme. Although Apple cleverly uses the term "extend", a more accurate term for the Express would be "repeater".
If the Express will extend by connecting to the Extreme using a permanent, wired Ethernet cable connection......highly recommended for best performance.....then the Express can be located exactly where you need more wireless coverage. There is no signal loss at all through the Ethernet cable, so the Express gets a full speed signal no matter where it might be located.
Post back to let us know which way to you want to go.

I have a Time Capsule with 2tb of storage, and an I-Mac with 500Gb. (which is at capacity) Can I use the Time Capsule to store data in addition to backing up the hard drive?

I have a Time Capsule with 2tb of storage, and an I-Mac with 500Gb. (which is at capacity) Can I use the Time Capsule to store data from my hard drive that I want to access later in addition to backing up the hard drive?

Can I use the Time Capsule to store data from my hard drive that I want to access later in addition to backing up the hard drive?
Yes, but if you move the "original" data on your iMac to the Time Capsule....then the "original" data is now on the Time Capsule disk.
When...not if...the Time Capsule disk has a problem, you have no backups for this data.
Perhaps a much safer plan might be to add an external hard drive attached directly to your iMac. Then, move the data to that drive from the iMac.
Now, Time Machine will back up both your iMac and the external hard drive so you have "originals" on one drive and backups on another. Would that plan work for you?

Can i use the airport express in my hotel with wired connection?

I'm going to be traveling quite a bit coming up and staying in hotels with wired internet connections in the room. Can i use the airport express to connect with the hotel's internet connection and then my ipad and/or iphone 4S? I'm new to Apple products so will certainly appreciate any info that may help. Thank you!

You will need to have AirPort Utility installed on the iPad and/or iPhone. It is free on the App Store
App Store - AirPort Utility
Connect the AirPort Express 802.11n to the hotel Ethernet jack using an Ethernet cable
Power up the AirPort Express and wait 40-45 seconds
Tap Settings, then tap Wi-Fi on the iPad
Tap the AirPort Express under the heading of Set up an AirPort Base Station
AirPort Utility will take a moment to to analyze the connection and then you can proceed with the easy guided setup
Once the AirPort Express is configured, you should not have to set it up again at the next hotel. But, you could if you want to.

I bought a second hand 4s iphone and I can't use the internet on 3g even though it looks like I'm connected ... can you help please?

I bought a second hand 4s iphone and I can't use the internet on 3g even though it looks like I'm connected ... can you help please?

Who's your carrier?
What country are you in?
Was it from a shop or a personal deal?
If your phone doesn't function on the cellular network, goto the carrier first

Can I use the optical digital audio cable to connect INSTEAD of the hdmi? My tv only has 2 hdmi ports, and they're both taken

Can I use the optical digital audio cable to connect INSTEAD of the hdmi? My tv only has 2 hdmi ports, and they're both taken

I'm afraid that's very misleading and inaccurate.
Firstly an adapter won't work, it would need to be a converter and then if it's a compliant converter it won't let you watch HDCP protected content such as that from netflix or from the iTunes Store.
Secondly, whilst I'm not going to debate whether component or HDMI is better, component is certainly not better if it's been converted from an HDMI signal. You can't make anything better by simply converting it to another type of signal.

What can be used to connect Panasonic Full HD SD/SDHC Camcorder to the iPod

I am thinking of buying the Panasonic Full HD SD/SDHC Camcorder which uses the new SDHC/SD Memory Card to store the movie clips. What I would like to know is there anything in the iPod accessories range, that I can connect to a Fifth Generation iPod so I can store all the clips from either the camcorder or the SDHC/SD Memory Card, so I can re-use the memory card. I understand that I will not be able view the moive clips on the iPod as the camcorder uses the AVCHD format.
All I want to do is use the iPod as a storage unit as I will be taking the camcorder on hoilday and I don't want to buy a lots of the 8Gb Memory cards nor take a portable hard drive with a card reader.

-I already read entirely those threads, but nothing about stereoscopic 3D AVCHD movies through USB port, on Panasonic TVPlasma3D.
(Also, Sony said me that is not possible to play 3D videos on your 3DTV through USB port).
I tried to made a H.264 videoclip, with .MP4 extension, at 960x1080p side-by-side layout, but nothing was displayed, and black screen.
I think that just the AVCHD movies, with .MTS extension, that comes from Panasonic consumer camcorder "HDC-SDT750", can play the 3D videos via HDMI cable, not USB port.
But not the exported videos from PremierePro via USB port.
I seen this tutorial from David K Helmly:
http://www.youtube.com/user/dhelmly#p/a/u/1/_YtF0c2bmkw
Dave export the video from PremiereProCS5 as "MPEG2-bluray" format with "Match Source Attributes (HighQuality)" Preset, and build the Bluray Disc in EncoreCS5, with the footage as MPEG2 with .m2v file extension:
1) Anyone tried to play correctly in 3D, those MPEG2-.m2v side-by-side files, in Panasonic3DTV, with BlurayDiscReader?
2) Why MPEG2.m2v side-by-side?
3) The official standard stereoscopic 3D format, is not the .MVC (MultiViewCoding) for Bluray3D Disc?
I am confused!
Help!
Horsepower0171.

Can I use the instrument I/O assistant express vi to communicate with a USB connected instrument ?

Can I use the instrument I/O assistant express vi to communicate with a USB connected instrument ? My PC is running Windows 2000 et Labview7 express.
where can I get information or examples on the assistant and USB communication ?

Yes you can - the Instrument I/O Assistant communicates with message-based instruments through VISA. VISA 3.0 supports USB instruments and VISA 3.0 is the version of VISA that installs with the Assistant.

After entering the Wlan password I can't use the „connect" button. The button is deactivated. Did somebody have a solution? I have an iPad 3 with IOS 8.0.2.

After entering the Wlan password I can’t use the „connect“ button. The button is
deactivated. Did somebody have a solution? I have an iPad 3 with IOS 8.0.2.

Your iPhone's iOS must be same or newer than the one in backups. In your case it is older so you need to update your iPhone and then recover it with backup.

My laptop is connected to company LAN on wire and I have another active wifi connection provided by a router. Can I use the wifi connection for mozilla connection and the wired for everything else? I'm on Win7.

I have 2 simultaneous active connections:
no1: wired connection to company lan; private IP 172.19..
no2: wireless connection to unrestricted traffic router; private IP: 192.168...
my question: can I use the wireless connection for mozilla traffic and the wired for everything else?
I'm on Windows7 Prof, all security updates installed.

Go to Control Panel > Network and Internet > Network and Sharing Center >
Click Change adapter settings from left panel > Open the network connection you want to change the DNS servers for by right click and select Properties > Select
Internet Protocol Version 4 (TCP/IPv4) and click Properties button > Choose the
Use the following DNS server addresses > enter the IP address for a
Preferred DNS server as well as an Alternate DNS server.
Primary DNS: 8.8.8.8
Secondary DNS: 8.8.4.4
This IP belongs to Google public DNS.
Note: Wired connections are usually labeled as Ethernet, while wireless ones are usually labeled as
Wi-Fi or Wireless Network Connection.
Uncheck Internet Protocol version 6
Mark as Answer if it's worked. Thanks. Balamurugan_Subramaniyan

Can I use the connection capacity of FMIS to estimate the FMS Enterprise?

Similar Messages

Maybe you are looking for