Can I use two airport extreme base station on the same network

Here is my network setup:
D-Link DCM-202 simple cable modem (DOCSIS 2.0 compliant)
attached via ethernet to
5th generation AirPort Extreme Base Station - Main (Bought last week)
attached via ethernet to
4th generation AirPort Extreme Base Station - Remote (Bought about 11 months ago)
The main AEBS is set to:
AirPort Section:
Base Station Tab -> Allow setup over WAN is CHECKED
Wireless Tab -> Wireless Mode: Creat a Wireless Network, Radio Mode: 802.11a/n - 802.11b/g, Radio Channel Selection: Automatic, Wireless Security: WPA2 Personal
Internet Section:
Internet Connection Tab -> Connect Using: Ethernet, Ethernet WAN Port: Automatic (Default), Connection Sharing: Share a public IP address
TCP/IP Tab -> Configure IPv4: Using DHCP
DHCP Tab -> DHCP Beginning Address: 10.0.1.2, DHCP Ending Address: 10.0.1.200, DHCP Lease: 24 hrs
NAT Tab -> The box following 10.0.1. is left blank, Enable NAT Port Mapping Protocol box is CHECKED.
The remote AEBS is set to:
AirPort Section:
Base Station Tab -> Allow setup over WAN is CHECKED
Wireless Tab -> Wireless Mode: Creat a Wireless Network, Radio Mode: 802.11a/n - 802.11b/g, Radio Channel Selection: Automatic, Wireless Security: WPA2 Personal
Internet Section:
Internet Connection Tab -> Connect Using: Ethernet, Ethernet WAN Port: Automatic (Default), Connection Sharing: Off (Bridge Mode)
TCP/IP Tab -> Configure IPv4: Using DHCP, IP Address: 10.0.1.2, Subnet Mask: 255.255.255.0, Router Address: 10.0.1.1, DNS Server(s): 10.0.1.1 (Everything else under this tab is blank)
Hope this helps with info needed.

Similar Messages

Can I use an Airport Extreme Base Station from the USA in Europe ?

A friend of mine gave me an Airport Extreme Base Station from the USA to Germany. When I hook it up to my PB by ethernet cable the Computer can't find the Base Station at all. If I use my Sonnett Aria Extreme PCI card it finds the station but in the pop-up menu asking in which country I want to use the airport station it only offers North and South American countries. How do I go from here and why is my PB not finding the station when I'm using cables ? Has it something to do with different models for different countries ? Any idea ? Thanx

Here you go ...
Changing the Radio Channel on the AEBSn
Either connect to the AEBSn's wireless network, or temporarily connect your computer directly (using an Ethernet cable) to one of the LAN ports of the AEBSn, and then, using the AirPort Utility in Manual Setup, check these settings:
AirPort - Wireless
o Channel: <Use Automatic or select a preferred channel>

Connecting to multiple Airport Express base stations at the same time?

I want to be able to use wireless internet and stream music to my stereo at the same time, but I only have a single internet connection behind my stereo and it's connected to the Pay TV. My options seem to be getting a new line installed behind the stereo so I can insert this into the same Airport Express base station I use for my music, or buying a second Airport Express base station and connecting it to one of the other internet connections in the room, then connecting to both Airport Express base stations at the same time.
Is this possible? Are there other alternatives?
Many thanks

Nate, Welcome to the discussion area!
Once you have a network, you can connect multiple AirPort Express (AX) to that network (wirelessly or via Ethernet). When your computer joins that network it can access all the AX.
You could take your current internet connection and run it into an inexpensive router with multiple Ethernet ports (not the AX). If this is a wireless router then your AXs could be located elsewhere and connect as wireless clients to that network. Once you computer joined that network it could stream music to the AXs.

PS3 can't see new Airport Extreme base station

I replaced my old airport extreme with the latest one, but now my PS3, which is on another floor, cannot see the base station, and the new base station has a lot less range than the old one. With my old one I could sit out in the back yard with my laptop, and the PS3 picked it up right away over our wireless network, but now, nothing. My laptop connects okay, just can't go very far. Nothing has changed except the base station itself. Please help.

Hello Uri. Welcome to the Apple Discussions!
A few things I would suggest that you try to see if either or both help with the PS3's connectivity to the 802.11n AirPort Extreme Base Station (AEBSn):
o If currently enabled, disable the Guest Network.
o Use a separate Network Name for the 5 GHz radio. Make sure that the PS3 connects to the 2.4 GHz radio's wireless network.

Can I use an Airport extreme to extend my ATT wireless network?

Hi
I get my internet through an ATT DSL wireless router positioned up in my attic. I have a studio in my basement with 2 computers, a plotter, a laser printer and a fax/scanner/photo printer. I've run an ethernet cable down from the attic in to a central location in my basement. I've run ethernet cable from the three printers to that same location. I want to set up an unused Airport extreme base station in my studio to connect the plotter and two printers to my wireless network. One snag is that one of my computers has a bad airport card slot and needs to be connected to the network with an ethernet cable.
Can you help me solve this?

OK,
Got er done this weekend and I have extended the network to my studio. One problem though, My main computer keeps dropping off the wireless network. It connects for a second and then gone. I have solved this for the moment by disconnecting my scanner from the AEBS and connecting my main computer to the AEBS. I still have not connected my laser printer to the network, but will use its USB connection to connect it to the AEBS. I just need to go buy a longer cord.
Things work for now and I can work on some jobs this week. I plan to search the boards to solve the dropping off problem soon.
Thanks again for all of your help.

Airport extreme base station detecting someone elses network but not mine.

Sorry if this subject has already been discussed but I couldn't see it anywhere.
I have an airport extreme base station set up and it works fine but this morning i noticed that I had very little signal which has never happened before so upon further investigation I noticed that my computer was hooked up to a Netgear network amd not my own usual airport "home" network.
I got my own network back again and my signal is now full strength. The worrying thing is that my computer couldn't seem to find my airport "home" network when I searched for it. I had to start again from scratch and reset it.
Is there a way I can tell my computer to use only my airport network and no other? Someone obviously has an open network nearby.
Message was edited by: lispiers

Try the steps indicated in Mac OS X 10.4 Help: Choosing preferred AirPort networks.

Airport Extreme Base Station - Need to extend network for extra distance

The literature on this topic is sparse. I have an Airport Extreme base station. I will like to "extend the signal" so that it is stronger in part of house. I would like to buy a product that will do this. Questions:
I think this is called "bridging".
1. Can I do this with the Airport Express as a 2nd unit??
2. Does the Airport Extreme work with other WDS 2nd units like Netgear?
3. Is there a darned manual to tell you how to configure the settings on BOTH stations?
Thanks.

How new is your Extreme? I ask because if your Extreme supports 802.11n, the setup process will be greatly simplified.

Ibook G-3 with old airport card can't see New Airport Extreme Base Station

I have been trying for a week now to get my G-3 ibook set up on my Airport Extreme Network. No matter what I do, I can't sign on to the network. When I put in the password I get an error message 3151. I have no idea what this means. I have read everything, restarted base, changed network password, trashed all airport and prefs on G-3 and reinstalled. Although my network shows up in the control strip, it doesn't show in the setup assistant. Please help if you can, I'm about to go crazy! Thanks.
Power Mac G5 and ibook G3 Clamshell Mac OS X (10.4.9) ibook is running 9.2.2
Power Mac G5 and ibook G3 Clamshell Mac OS X (10.4.9) ibook is running 9.2.2
Power Mac G5 and ibook G3 Clamshell Mac OS X (10.4.9) ibook is running 9.2.2

Dear Duane, I did have 802.11b configured, but I had the WPA instead of WEP enabled. When I reconfigured my network, the clamshell was instantly able to join and use the network. I have many many questions about how to use the network to allow both computers to communicate, but I'll read up on it and I'm sure the answers will be there. You saved me $240.00 for the 1st hour and $160.00 for anything over that Techserve was going to charge me to come and set it up. I can't thank you enough. Everyone tells me not to waste money, but to save for a new ibook with System X, but I love my old clamshell and I'm going to get it a bigger hard drive so it can be upgraded to run OS X. It's the old 4 Gb one. I can't thank you enough for your solution! Now I can work on the laptop in my bedroom! I love Mac stuff and I knew the Extreme base station would work, regardless of what all the posters have been saying.
Power Mac G5 and ibook G3 Clamshell Mac OS X (10.4.10) ibook is running 9.2.2

Can I use an Airport Express Base Station to extend non-Apple router range?

We have a Netgear 802.11n router in our house. I just bought a MacBook Pro and now am accessing out wifi from the other end of the house along with my iPod Touch 4g. Both seem to show at best about half strength signal strength. House is small and nearly all devices on same floor.
Can I use the Apple Airport Express Base Station as a bridge to extend our wifi network giving me stronger signal for my Apple devices or will it only work with Apple routers? Netgear and others like Hawking make wifi range extenders and those are still under consideration.

It would be extremely unlikely that an AirPort Express would "extend" the wireless network produced by the Netgear router using wireless only. Apple's "extend" feature appears to be proprietary among Apple "n" routers. As far as we know, it does not work with any other manufacturer's products for the purpose of wireless only extension.
If you are planning to connect the AirPort Express to the Netgear using an ethernet connection, then it could be configured to extend that way.

Can't see my Airport Extreme base station

I wanted to upgrade my Base station's security to WPA2. So I went to the Airport Admin utility - But the base station does not appear there. My base station is set to be a close hidden network so I suppose that was the reason why it didn't appear.
So I decided to reset the base station. After pressing the reset button for 10sec
I went back to my PB and noticed that my wireless network name was changed to Apple Network ###### (which indicate that the Base station reset) BUT I still can't see my base station in my Airport Admin Utility.
1. Is there another way to reset the base station? did I do it right ?
2. Is there a way to see my hidden base station in the Airport Admin Utility ?
I know that I can log to a specific address (+password) but which one
should I use ?
Thanks
Eric

If you press and release the reset button on the base station, it will restart. If you unplug the power, then plug it back in, it will reboot. Holding the reset button like you did will cause the base station to revert to factory specs, meaning that you lost all of your customizations. So you have to re-configure the base station now.
If your PowerBook was connected to your network, you should see the base station in the Admin utility. Did you check to make sure you were connected to the network before you went into the Airport Admin Utility?
Doc

Using both Airport Extreme Base Station and Airport Express

I am using a Airport Extreme and a AX, my goal is to use the base unit on one floor of the home and they AX as an extender.
I have linked the AX unit to join the existing network, now how to do I enable WEP 128 bit?

Here are the WDS setup steps...
AEBSn - WDS Setup
(Note: To facilitate the WDS set up, place the base stations within near proximity of each other during the set up phase, and then relocate them to their desired locations when complete.)
Main Base Station Setup (AEBSn)
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as the main base station.
o Open AirPort Utility (located in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the main base station, and choose Manual Setup from the Base
Station menu, or double-click the base station to open the configuration in a separate window.
o Enter the base station password if necessary. If the base station is using the default password of public, you will not be prompted for a password.
o Click Wireless in the toolbar, and then choose “Participate in a WDS network” from the Wireless Mode pop-up menu.
o Click WDS and then choose “WDS main” from the WDS Mode pop-up menu.
o Select the “Allow wireless clients” checkbox if you want client computer to connect to this base station.
o Click the Add "+" button and enter the MAC address of the base stations you want to connect to this base station.
o Click Update to send the new settings to the base stations in the WDS.
Remote Base Station Setup (AX)
o Click the AirPort status menu in the menu bar and choose the wireless network created by the base station you want to set up as a remote base station.
o Open AirPort Utility (in the Utilities folder in the Applications folder on a Macintosh computer, or in Start > All Programs > AirPort on a computer using Windows).
o Select the remote base station, and choose Manual Setup from the Base Station menu.
o Enter the base station password, if necessary. If the base station is using the default password of public, you will not be prompted for a password.
o Enter the same network password as the main base station, if necessary.
o Click AirPort in the toolbar and click Wireless. Choose “Participate in a WDS network” from the Wireless Mode pop-up menu, and choose the same channel as the main base station from the Channel pop-up menu.
o Click WDS and choose “WDS remote” from the pop-up menu.
o Enter the MAC address of the main base station in the WDS Main field. The MAC address is also referred to as the AirPort ID and is printed on the label on the bottom of the base station.
o Click Update to transfer the settings to the base station.
(ref: Pages 41-45 of "Designing AirPort Extreme 802.11n Networks.

Why does my AirPort Extreme Base Station lose the internet when I unplug my printer Ethernet cable?

I just changed ISPs to Qwest from Speakeasy. New modem. Now my etherneted (from extreme base station) printer (Brother HL1870N) doesn't work.
And if I unplug the printer ethernet cable from the base station, the base station loses the internet connection.
Any help would be appreciated.
thanks

whats the version on your airport extreme and what renerations is it?

How do I make a wired connection to my Airport Extreme that will share the same network as any wireless connection to it?

Here's the set up.
I have a cable router into the house and then an Airport Extreme connected to it. Everything connects wirelessly to the Airport Extreme apart from one computer in the same room as it, which I wired into the AE with a cable (it's a gaming PC and has no wireless).
How can I get that wired machine to use the same network as all the other wireless devices? When I plug the cable into it, the gaming PC only picks up the network being created by the cable box which I don't use.

There is nothing stopping you connecting to the wireless computers if you have sharing turned on..
How can I get that wired machine to use the same network as all the other wireless devices? When I plug the cable into it, the gaming PC only picks up the network being created by the cable box which I don't use.
I don't quite follow this..
If the cable modem is a router.. the AE must be in bridge mode..
So all routing is handled by the cable modem router.. and the wireless clients will all be in the same IP range as the PC is.. please check that by opening the PC command window and type ipconfig /all
Then go to one of the wireless devices and check that it also has the same IP range.. eg,, 192.168.x.x and same router or gateway address eg 192.168.1.1 and same DNS.. which is the same as the router address..
Then in the command window of the PC use the command ping to see if the other devices respond.. ping it by name or by IPaddress.
If there is no response.. windows has decided it is in a public network.. and slammed up the firewalls.. make sure your network is set as home for location.. and make sure the firewalls .. you can have multiple if you have an internet security package are not blocking local network access.
Also remember PC and Mac in a network can take a bit of fiddling to see each other. But ping should always respond and in both directions.

I am trying to use share a Hitachi TourPro 2tb external hd using my Airport Extreme base station. I can't get the hd to appear in the disks section of the airport utility though.

I've tried using a powered and non-powered USB hub without success. Plugging the hd directly into the airport didn't work either. The hd functions fine when plugged into a USB port on 3 other computers so it doesn't appear to be a hd issue. I've reset the airport with and without the hd attached but no success in getting the hd to appear in the airport utility. I followed all of the instructions in Apple's Airport support section but no luck.
All my pc's are running on XP Pro (service pack3). The airport extreame is working flawlessly except for this one particular issue which, unfortunately, was one of the main reasons I purchased it. I've looked through numerous discussions already in the community and tried some suggestions such as attempting to map the drive using the airport's IP address but still no luck.
Does anyone have any suggestions or can tell me what I'm missing in the set-up process?

When trying to troubleshoot my problem I discovered a forum that was saying certain NTFS drives work just fine
Apple support says that an NTFS or exFAT drive cannot be used when connected to the AirPort Extreme.
I suppose it is possible that someone might have been using some type of special software on the drive that might perform a "conversion", but without more details, it is hard to know.
Note: ExFAT and NTFS formats aren't supported.
http://support.apple.com/kb/HT2426

Can I use 2 airport express base stations to extend my G and N networks?

I currently have my Time Capsule broadcasting an N only signal at 5ghz and use the router that came from the cable company to broadcast a G signal. Can I buy 2 expresses to repeat both networks?

Here's what I see when I try this. Your results may vary.
Depending on your connection quality, distance from the TC, etc., the speed will drop by approximately 40-50% if you change to the 2.4GHz compatible settings that you mention. In other words, if you were getting a Transfer Rate of 250-270 on 5GHz, the Transfer Rate will likely drop to 110-130.
This is assuming that there are only "n" devices active on the network. If you have a "g", or "b" device active on the network, the overall network speed will drop to "g" or "b" levels depending on the device that is active. If you have a "b" device active, the Transmit Rate will likely drop to the 25-30 range.
You can check the Transmit Rate on your Mac by holding down the "option" key while you click on the fan shaped Airport icon at the top of the screen.

Can I use two airport extreme base station on the same network

Similar Messages

Maybe you are looking for