Can Keyboard be configured to a port?

Can we configure keyboard to a port and use socket program to read data from that port...

please....This is not an elaboration of your requirement!

Similar Messages

Can't configure both WAN ports on 1811 with SDM

Hi,
We recently procured an 1811 router to replace a SOHO linksys at a store we service. We needed redundant WAN interfaces to use the DSL as a backup to the main cable connection, and a Linksys RV082, while doing the job when it actually worked, died repeatedly. We decided after looking at the 1811's feature set to just get the Cisco and be done with it and not monkey with SOHO gear anymore.
Where I'm having difficulty is SDM won't let me configure both WAN interfaces from the GUI, it only allows me to configure one. I have it configured, and the router is working nicely in the test lab but I need to get that other interface configured and failover enabled before I can put this thing into production.
What am I doing wrong? Do I need to suck it up and learn IOS?
Thanks,
Todd Phipps
Certco, Inc.

I ended up figuring out the IOS commands to enable one fastethernet port as a primary and the other one as a backup (running both cable and DSL for redundancy; it's a grocery store that runs electronic transactions over IP so 100% availability is a must).
The trouble I was running into in SDM is that while it would allow me to configure one WAN port through the GUI, the config options for the second one were grayed out. Now that both are configured through IOS the edit buttons for both WAN interfaces appear normally in SDM. It's almost as if Cisco didn't want users to be able to configure both interfaces graphically for initial setup.
Now just to test it at the site before the store opens to see if the failover works...
Todd

Can you configure a static port to use with certsrv.msc?

I am trying to use certsrv.msc to connect from my workstation to the CA for administration purposes. Workstation is Win7, CA is 2008 R2 Enterprise running Enterprise Subordinate on a dedicated box.
I configured a static DCOM port for certsvc by following this article, including bouncing the service and also rebooting the CA box:
http://social.technet.microsoft.com/wiki/contents/articles/1559.how-to-configure-a-static-dcom-port-for-ad-cs.aspx
The static port was opened in the firewall from my workstation to the CA. We also found that TCP 445 was required, so that has been opened as well, port 135 & other ports normally needed for autoenrollment should be open. Sniffing the firewall
showed that a random high numbered port that is not the static dcom port is being attempted - this is the only port showing dropped packets & no traffic on the static port.
I am wondering if there is a way to configure a static port for this high-level random port to use with certsrv.msc as I was able to do with the certsvc dcom port? I am trying to avoid having tens of thousands of network ports wide open going to my
CA... Thanks in advance!

Hi Steve,
I am sorry that I wasn’t able to find references about restricting certificate services only use one port in the random port range.
However, we can configure RPC dynamic ports allocation to restrict port range. In the meantime, we should keep at least 100 ports open to keep necessary system services running.
More information for you:
How to configure RPC dynamic port allocation to work with firewalls
http://support.microsoft.com/kb/154596/en-us
Service overview and network port requirements for Windows
http://support.microsoft.com/kb/832017/en-au
Firewall Rules for Active Directory Certificate Services
http://blogs.technet.com/b/pki/archive/2010/06/25/firewall-roles-for-active-directory-certificate-services.aspx
Best Regards,
Amy Wang

Pa-mc-8te1 can i use this a ethernet POrt how to configure it ...

pa-mc-8te1 can i use this a ethernet POrt how to configure it ...

Hi Venkat,
Please ask this question in routing/switching forum. As far as i know you can only configure pa-mc-8te1 as E1 or T1 ports. For more details please visit the below link.
http://www.cisco.com/c/en/us/td/docs/interfaces_modules/port_adapters/install_upgrade/multichannel_serial/8-port_multichannel_t1-ei_8pri_install_config/8port_t1/2738ovr.html
Regards,
Kanwal
Note: Please mark answers if they are helpful

Can't configure tacacs-server port

We're unable to configure a specific port, which is required for our customer for the tacacs-server. One of the devices is a 7604 router running this image -
c7600rsp72043-adventerprisek9-mz.122-33.SRD6.bin. The other device is a 2960 switch with the following image - c2960-lanbasek9-mz.122-35.SE5.bin.
We don't get the option to add a port after the tacacs-server host x.x.x.x command.
Any ideas would be greatly appreciated!
Regards..

Hi
Please go through this link, this will be helpful regarding TCSACS Authentication and Fortigate configuration:
http://www.cisco.com/en/US/docs/net_mgmt/cisco_secure_access_control_system/5.2/user/guide/acsuserguide.html

Can I simultaneously configure a device to more than one task?

Can I simultaneously configure a device to more than one task? I am trying to trigger on some of the input data. When I tried to configure the same device to more than one task, I get an error:
Error -10408 occurred at Digital Group Config.
Possible reasons:
NI-DAQ LV: The specified channel is in use.
I have attached a copy of my VI. In the first and second sequences I am using device 1.
Attachments:
Can_I_simultaneously_configure_a_device.doc ‏19 KB

Hello;
The best way to have multiple tasks running on the same DAQ device is by syncronizing those in the hardware level. What I mean by that is, to use the same clock pulse train to clock the different tasks.
For instance, in case you want to do Analog Input and Analo Output at the same time, you can use the AI Start Scan (which is the clock pulse train that will clock the analog input task) to be routed to the AO Update clock (which is the clock that controls the Analog Output tasks of your device). You can extend that idea for counter operations as well.
For digital operations, if you are not using one of the digital boards that support strobed operations, such as the 653x ones, you won't be able to synchronize the digital tasks with the analg tasks, s
ince the digital ports updates through Software calls only.
You are probably getting that error because you are trying to use the Digital Group Config.vi (or some other VI that calls the Digital Config.vi) with a board that doesn't support handshaking operations, such as the MIO ones.
Hope this helps.
Filipe A.
Applications Engineer
National Instruments

How to configure the eth1 port of NIcRIO 9024 to another IP address and subnet mask

Hi ,
I am using cRIO 9024 and am planning to configure it to be an MMS server that interacts with a client which is in another network with different IP and subnetmask. I want to run the server VIs from the host computer via the eth0 port and want to communicate the MMS messages through the eth1 port. the eth0 port is configured as a static IP as shown in the screenshot attached and would like to assign a separate IP and subnet mask to the other port . But when I try to save the configuration I get the error "Could not save your changes tot he target.The subnet mask for eth1 is invalid" .
I have already directly cross connected the Crio and have disabled the firewalls and still am not able to configure it.
1) is it possible to configure the ethernet ports to have separate IPs corresponding to different networks and thus the subnet masks?
2) If its possible then what is the mistake i am doing while configuring it ?
I would be extremaly grateful to have a reply on this as its pretty desperate to spend a lot of time just to set up the IP configurations..!!!!!
Regards
Abhinav

Dear Abhinav,
I'm sorry but what you are tryining to do is not suported by the Second Ethrnet Port on any cRIO and so you getting this error meeage.
Here a abstract out ouf the KnowledgeBase How do I Configure the Dual Ethernet Ports on Real-Time Controllers?:
Ethernet port 2 is currently not supported to communicate outside its own subnet. There is no capability of configuring the Default Gateway for Ethernet port 2 and therefore cannot connect to a large isolated intranet. However, there appears to be a common misconception that this port can only be used for communication between NI products: this is not the case, though any communication through the secondary port must be within the same subnet.
Kind Regards,
SG3 | Applications Engineering | National Instruments | NIG |

PLEASE I JUST NEED TO CONFIGURE TO OPEN PORT 22

Very sorry for the redundant post. I am in a desperate situation where the RAID on my NAS has been lost and I need remote tech analysis ASAP.
Can anyone out there please help me configure so that Port 22 is open???
I have a Thecus N5200 and an brand new Airport Extreme.

bevatore wrote:
Do I use the same Private IP address or do I use the Remote Management IP from Sharing in the computer's Preferences.
The "Remote Management" IP address should be the LAN IP address that your router gives to your computer. That should be the same as a "private IP address".
Also, do I need to to configure a DHCP Reservation for this IP in AirPort Utility?
If you don't do that, the IP address of your computer could change between restarts, causing the mapping to fail. If you only have one wireless client, that's probably unlikely. However, reserving an IP address will guarantee that your computer always has the same IP address.

Change/Configure Host and Port for the Web Service Proxy with Server

Hi,
Is there a way to configure Host and Port in generated proxy for Web service depending upon server. (ADF 11g)
Scenario:
We are consuming Credit Card web service from a service provider and have different Host and Port details for development, QA and Prod.
So we created proxy classes using wsdl for development and things work fine, but when deploying code to QA or Prod we need to change the Host
and Port details.
Is their a way we could user variable's for Host and Port which looks to some configuration file to evaluate their values
based on server.
I am a bit new to this web service .. will appreciate if someone could provide an example.
Thanks.

Are you using Web Service Proxy or Web Service Data Control?
If you are using Web Service Proxy. Right click on your Proxy --> Properties --> Port Endpoints. Here you can change the IP & Port details for each port.
Venkat

How can ftp service on non-standard port be load balanced using Cisco ACE.

How can ftp service on non-standard port be load balanced using Cisco ACE.For example ftp service required on tcp 2000 port

Hi Samarjit,
you can do this by specifying the port number in the class map that you create . Please find the below mentioend config guide where you can specify the tcp/udp port , range or ports or even the wild card to match the port.
http://www.cisco.com/en/US/docs/interfaces_modules/services_modules/ace/v3.00_A1/configuration/administration/guide/mapolcy.html#wp1318826
Regards
Abijith

LC Configuration Manager problem, port 8080 still in use?

I'm installing a trial version of the Adobe LiveCycle ES server using JBoss on my system for some development. I'm running Windows Vista Ultimate 64-bit. I did a turnkey installation. That goes fine. When I run the configuration manager, it gets to the deployment step and the "Verifying ports required by service JBoss for Adobe LiveCycle ES are available" step, and I get this error:
"The following ports required by JBoss for Adobe LiveCycle ES are still in use 8080.
Another instance may be running or another application may be using some of the required ports."
Nothing has port 8080 bound. I've checked with a netstat -a -o command. I can run tomcat and it binds port 8080 just fine. I've disabled UAC (I'm logged in as an administrator), disabled windows firewall, and even uninstalled and reinstalled livecycle. One thing that happens if I restart my computer and try again is that it fails for a different error about being unable to stop the JBoss service. If I stop the service manually and retry, it just reverts to the port error above.
This error is really confusing and I can't seem to figure out how to fix it. I need to get this up and running so I can develop and test my application. Anyone have any insights or suggestions?
-Sam Fahmie

I have the same problem trying to install on Vista64. Perhaps it only works on XP and 2003?
"Chances are that the installer is failing at the stage where it tries to create a Windows service for JBoss and fails"
This isn't the installer, it's the configuration manager that runs after the installer.
The installer creates the service just fine. It's when the manager tries to start the service that it fails. If you manually start jboss then run the configuration manager again then it stops at the same point complaining that an instance of jboss is already running. If jboss is already running, why doesn't the installer just skip that stage and continue?
I've found that after starting jboss manually I can connect to the 8080/adminui page (took a very long time to respond the first time I connected), but the default login doesn't work. I assume some extra steps haven't been done. Is there any way to bypass the starting of jboss in the config manager in order to complete the other steps?
I've also tried launching the configuration manager bat file from an administrator mode console, but it fails at the same point.
2 days screwing around with this software, both turnkey and manual on Linux and I haven't managed to get it to work. Quality. Next step will be to see if I can get a copy of XP from the museum and a find machine to run it on.

Can I use a mini display port to VGA adapter and then a VGA to av adapter to connect my MacBook pro to my standard definition tv?

Can I use a mini display port to VGA adapter and then a VGA to av adapter to connect my MacBook pro to my standard definition tv?

No. You need a converter box like this to go with your MDP-VGA adapter:
http://www.amazon.com/PC-To-TV-Video-Converter/dp/B001CJOLBW/ref=pd_cp_e_2

How can i wrote configuration file in Log4j

iam new log4j .i have seen one small programme in log4j examples folder ..i e. shown below
Sort.java
=====
package examples;
import org.apache.log4j.PropertyConfigurator;
import org.apache.log4j.Logger;
import org.apache.log4j.Priority;
Example code for log4j to viewed in conjunction with the {@link
examples.SortAlgo SortAlgo} class.
This program expects a configuration file name as its first
argument, and the size of the array to sort as the second and last
argument. See its source
code for more details.
Play around with different values in the configuration file and
watch the changing behavior.
Example configuration files can be found in <a
href="doc-files/sort1.properties">sort1.properties</a>, <a
href="doc-files/sort2.properties">sort2.properties</a>, <a
href="doc-files/sort3.properties">sort3.properties</a> and <a
href="doc-files/sort4.properties">sort4.properties</a> are supplied with the
package.
If you are also interested in logging performance, then have
look at the {@link org.apache.log4j.performance.Logging} class.
@author Ceki Gülcü */
public class Sort {
static Logger logger = Logger.getLogger(Sort.class.getName());
public static void main(String[] args) {
 if(args.length != 2) {
 usage("Incorrect number of parameters.");
 int arraySize = -1;
try {
 arraySize = Integer.valueOf(args[1]).intValue();
 if(arraySize <= 0)
 usage("Negative array size.");
catch(java.lang.NumberFormatException e) {
usage("Could not number format ["+args[1]+"].");
PropertyConfigurator.configure(args[0]);
int[] intArray = new int[arraySize];
logger.info("Populating an array of " + arraySize + " elements in" +" reverse order.");
for(int i = arraySize -1 ; i >= 0; i--) {
 intArray[i] = arraySize - i - 1;
SortAlgo sa1 = new SortAlgo(intArray);
sa1.bubbleSort();
sa1.dump();
// We intentionally initilize sa2 with null.
SortAlgo sa2 = new SortAlgo(null);
logger.info("The next log statement should be an error message.");
sa2.dump();
logger.info("Exiting main method.");
static void usage(String errMsg) {
 System.err.println(errMsg);
 System.err.println("\nUsage: java org.apache.examples.Sort " + "configFile ARRAY_SIZE\n"+
"where configFile is a configuration file\n"+" ARRAY_SIZE is a positive integer.\n");
System.exit(1);
and
SortAlgo.java
==========
package examples;
import org.apache.log4j.Category;
import org.apache.log4j.NDC;
Example code for log4j to viewed in conjunction with the {@link
examples.Sort Sort} class.
SortAlgo uses the bubble sort algorithm to sort an integer
array. See also its source
code.
@author Ceki Gülcü */
public class SortAlgo {
final static String className = SortAlgo.class.getName();
final static Category CAT = Category.getInstance(className);
final static Category OUTER = Category.getInstance(className + ".OUTER");
final static Category INNER = Category.getInstance(className + ".INNER");
final static Category DUMP = Category.getInstance(className + ".DUMP");
final static Category SWAP = Category.getInstance(className + ".SWAP");
int[] intArray;
SortAlgo(int[] intArray) {
this.intArray = intArray;
void bubbleSort() {
CAT.info( "Entered the sort method.");
for(int i = intArray.length -1; i >= 0 ; i--) {
NDC.push("i=" + i);
OUTER.debug("in outer loop.");
for(int j = 0; j < i; j++) {
 NDC.push("j=" + j);
 // It is poor practice to ship code with log staments in tight loops.
 // We do it anyway in this example.
 INNER.debug( "in inner loop.");
if(intArray[j] > intArray[j+1])
 swap(j, j+1);
 NDC.pop();
NDC.pop();
void dump() {
if(! (this.intArray instanceof int[])) {
DUMP.error("Tried to dump an uninitialized array.");
return;
DUMP.info("Dump of integer array:");
for(int i = 0; i < this.intArray.length; i++) {
DUMP.info("Element [" + i + "]=" + this.intArray);
void swap(int l, int r) {
// It is poor practice to ship code with log staments in tight
// loops or code called potentially millions of times.
SWAP.debug( "Swapping intArray["+l+"]=" + intArray[l] +
 " and intArray["+r+"]=" + intArray[r]);
int temp = this.intArray[l];
this.intArray[l] = this.intArray[r];
this.intArray[r] = temp;
This program expects a configuration file name as its first
argument, and the size of the array to sort as the second and last
argument. See its source
code for more details.
please help me how can write that configuration file
thanks

Hi bala,
check that log4j manual I pointed to in yer previous thread.
This is a pot-boiler config file... Copy it into some file say "props.conf" and use it.
# Set root logger level to DEBUG and its only appender to A1.
log4j.rootLogger=DEBUG, A1
# A1 is set to be a ConsoleAppender.
log4j.appender.A1=org.apache.log4j.ConsoleAppender
# A1 uses PatternLayout.
log4j.appender.A1.layout=org.apache.log4j.PatternLayout
log4j.appender.A1.layout.ConversionPattern=%-4r [%t] %-5p %c %x - %m%nCheers,

Can there be more than one port for the same logical system

Can we have more than one TRFC port for tranferring data from one logical system to another?
The requirement is to transfer same basic idoc type from one logical system to another through two different ports. Is it possible?
For eg. some specific data (country specific) for the same basic idoc type can be sent through a separate port and the other data through a different port inorder to distinguish between the two.

Hi Shital,
I don't think so. Because of that what i told you. There would be a dirty trick (back routing) to solve your issue. But its quite difficult and not standard. You create two http receiver services and two http sender services. You route your message depending on payload to the one or the other http receiver channel. The receiver is in both cases: THE XI! Now you have a second message, which you can route to IDoc adapter. But in this case you have different sender and in the receiver determination you can put the sender, so you will be able to use different communication channnels and so different ports / destinations.
Advantage: Your task would run, no performance problem (http: very good, asynchron)
Handicap: You see every message double in the monitoring, the scenario is not easy to understand and it is a big task 4 other people to change it.
Regards,
Udo

What are the different types of bind that we can use to configure COREid?

Hi
What are the different types of LDAP bind that we can use to configure COREid?
Thanks for your input.

(http://download-west.oracle.com/docs/cd/B28196_01/idmanage.1014/b25343/idconfig.htm#BABGAECB)
7.5.2 Creating an LDAP Directory Server Profile

Can Keyboard be configured to a port?

Similar Messages

Maybe you are looking for