Can losing connection with an external drive lead to its failure?

My iTunes library is currently wireless, through my Airport Extreme, so I can use it both with my Macbook Air and my iMac. Of course the downside is only one computer can access it at a time and I'm limited by the range of the Airport, but it works for me... Since my library is too big for iTunes Match anyways and I live in a small appartment it's perfect.
Anyways, my problem is, this setup is fairly new, and a few times yesterday while I was working on adding new music to my library (ripping my CDs in lossless), I got the error message that connection was lost with my iTunes drive!
My internet didn't seem to flinch though, which is weird. But it doesn't seem to be the "the disk was not ejected properly" external disk error that's been going around, as I HAVE that **** problem with another of my drives... (connected via cable) and it's not the same error message.
This one is just saying the connection was lost... like Airport had the hiccups or something.
Time for me to click on "ignore" and I could go back to what I was doing.
Except twice, this happened WHILE a track was importing into iTunes!
The first time, I got an error message saying it was impossible to read or write to the device... I was scared... closed iTunes, re-opened... and it looked like nothing happened! Phew. Even the freshly imported tracks were there, up the to one that was importing when it lost connection, which of course wasn't imported.
But then it happened again... while it was, again, importing...
This time, restarting iTunes didn't cut it.
When I opened Airport Utility to check, I had yellow question mark, and a message saying the attached drive was failing, or corrupted, something like that (can't remember), to plug it directly in my computer and repair it!
I did that, opened Disk Utility... and the drive won't mount.
I tried the few tricks I know, still won't mount.
So now I'm in the middle of creating a disk image on one of my other external drives (it's been hours and only a third has been done, I'm crossing my fingers it doesn't just freeze, give me an error message or tell me there's not enough space... because I couldn't check how much space was used since it wouldn't mount... and it has been a while since I checked).
I'm also in the middle of checking for data recovery with my old StellarPhoenix app... not even sure what it could do or if it still works...
But all that to wonder : can a simple network disconnection be enough to do that???
If so, how come people rely on NAS, how come so many use Airport in conjunction with external drives?! It just doesn't make sense to me...
Maybe this was just a weird coincidence? Or maybe I'm taking the problem the wrong way, and the lost connection happened because the drive was failing? In that case I just find it weird that I didn't see any sign of that while it was connected directly to my iMac, right until a few days ago!
...Gee, I'm tired of buying external drives!
For the curious, this one is a 2TB Samsung (Iomega), bought in december 2010, so just 2 years old.

Thanks edex67!
Now the question would be, are numerous losses of connection in a day normal for Airport Extreme, or is mine failing?
Can't find a model number and the serial doesn't lead anywhere, but I'm pretty sure it dates back to 2008, the second generation.
A small update: Problem seems to definitely be just in the filesystem since after formatting all seems well, while I can't restore with my disk image, as after hours of scanning it, I now get the error message that Disk Utility can't scan it because of an internal error.
Now let's hope I can save the data, because even though I regularly did backups of that disk, I would still lose those hours of new imports and organization I had just done when it failed... 
I'l look for Gparted also... thanks!

Similar Messages

  • Time machine has losing contact with my external drive, connected via a USB port.

    Recently my Time Machine program has begun losing contact with my external drive, connected via a USB port. When I attempt to open Time Machine, it indicates there is no external hard drive.  When I click on "setting up time machine" it opens airport utility.   I've tried rebooting, run disk utility repairs for both hard discs, pulled and reconnected the USB cable, even completely shut down the system.    Eventually the two re-establish contact, but I'm not certain what I've done that causes this.  The lost contact appears to happen during the weekends.  The external hard drive is a MJaxtor OneTouch 4. What should I be doing to solve this problem once and for all?

    I use a little app named EasyFind - free at the App Store. It will allow you to search individual volumes or all volumes.
    Download it and see if it will help.
    Clinton

  • PC can't connect to AEB external drive, but Mac can.

    Until recently I was able to connect to the external hard drive I have attached to my 1 generation Airport Extreme base station, version 5.6.1, running firmware version 7.6.4. It just stopped showing up one day and it gives me errors when I try to connect saying credentials are wrong, but they're not. I've tried everything I could find, including changing some Windows settings, reverting firmware, resets and a lot more. It used to automatically connect at start up, and showed up as a 'Z' drive, and worked great. The drive is fine as well, that was my first concern. I just connected to it from the File Browser app from the app store, and my other Apple devices, MPB, Apple TV, both see it. Just not my Windows 7 pc. This was my last resort after many hours of troubleshooting. Any help would be greatly appreciated, thanks in advance.

    Standard network troubleshooting.
    1. If you are using wireless plug in by ethernet.. never trust wireless.
    2. If the computer gets an IP from the Extreme.. ping the extreme in a command window.. does it respond? It must respond before worrying about all the rest.. Windows can auto decide it is now in a public location and ram up the firewall. Make sure your network location is home.. and if necessary turn off the firewall.. the TC must respond at least by IP.. name as well would be good.
    3. Open the Control Panel admin tools and make sure bonjour is running as a service. If it has failed stop and restart it.
    4. Try mounting the hard disk directly by IP in windows explorer.
    \\10.0.1.1 (replace with the actual IP address).
    5. If it is only wireless that is the problem.. you probably had some sneaky windows security patch install and that ruined everything.. windows patches are often 2 steps forward.. 3 backwards.. you can no longer be attacked because you no longer have internet connection!!

  • Can't connect to FTP external drive - EA3500

    Trying to connect to my external hardrive using FTP app from my phone to test it.
    I uncheck the 'filter unwanted traffic box' and even tried switching the port from 21 to 4460.
    Can't seem to connect on my iphones brower I get 'server not responding' and any app I use cannot connect.
    Using UTF-8 encoding too.
    Heres what I type into the browser, "ftp server ip : port"
    Any help would be appreciated. 

    Shouldn't it be?
    ftp://192.168.1.1
    or
    ftp://192.168.1.1:4460
    Please remember to Kudo those that help you.
    Linksys
    Communities Technical Support

  • HP Officejet Pro 276dw MFP - can't connect with the printer driver (but web browser works)

    Hi,
    I used to own an 8500 pro which got replaced by the 276dw due to HW malfunctioning of the old model. I installed the driver (full set, win 8.1 64 bit) from the HP download area over the installed printer. I can access the printer using it's IP address. Ipad Airprint works well. The only problem is that I can't get the printer driver to connect to the printer, but the printer driver displays the printer with the correct address. Print and Scan doctor detects incomplete install and download 184MB, one bit at a time ... it will take more than an hour.
    I believe - due to a message that something needs to be stopped during the install (in order to get rid of the SW for the old printer) - that this thing is stil stopped, and I need to restart that (or if it is a service I need to reset it to automatic start).
    Any idea anyone?
    Thanks and with best regards,
    Holger

    update: The Print and Scan doctor did not help, but I finally added the printer using the default windows method. So I can print, but scan to PC obviously doesn't work, and neither does the Fax printer. Help still appreciated.

  • Why I can't connect to my external drive?

    Dear All,
    I'm a very new user to lion Os. I'm now not able to connect to my buffalo 500 gb ext drive. it's showing ' the device you inserted is not readable by this mechine'
    what should i do? Kindly please guide me.
    Best Regards,
    Win

    Not sure which Buffalo you have but a quick Google finds this page:
    http://www.buffalo-technology.com/knowledgebase/users/kb.php?id=10241&category_i d=0&sid2=
    where they have different drivers for Lion.
    Regards,
    Colin R.

  • Losing connection with external monitor

    Hi
    I have a MacPro G5 running FCE HD with firewire connection through a Sony DSR11 deck hooked up to a Sony Trinitron DV Pal external monitor. I was until recently using a brand new external drive shared over a network connection with a PowerMac G4 running FCP3 linked to DV/VHS combo deck and Trintron monitor. That shared drive has just failed and is awaiting replacement so I am back to using the internal drive on the MacPro - which is where I have recently encountered a very frustrating problem. One day the output to the external monitor is fine, the next day is has gone. I have tried two suggestions from this forum which have both worked - temporarily.
    1. Creating a new user account. 2. Trashing preferences. If this problem persists despite these short term fixes can anyone tell me if there is something else I should/could be considering. Also can I run FCE on the PowerMac ?
    Many thanks

    Tom
    Thanks for the reply. I will try a new cable if I keep losing the connection. The external drive (when I get it replaced) is shared over the ethernet. The external monitor problem I have is only with the set up running FCE on the Mac Pro. My external monitor connected to the Power Mac G4 with FCP3 has worked fine for 3 years now.

  • Using an external drive with shared files (iPhoto, iTunes), attached to a Time Capsule, can the contents of the external drive be backed-up to the internal Time Capsule drive? Perhaps a RAID1 mirror to a partition?

    Using an external drive with shared files (iPhoto, iTunes), attached to a Time Capsule, can the contents of the external drive be backed-up to the internal Time Capsule drive? Perhaps a RAID1 mirror to a partitioned Time Capsule? I understand that the Time Machine (software) cannot backup a networked drive (the external) and that Time Capsule (the router/wireless hard drive) does not have its own backup software... so it won't backup the connected drive. What I would like is an alternate solution for having an automated backup of a networked drive. A 2TB Time Capsule has more than enough space for Time Machine backups of my family of Macbooks, so I had hoped to mirror a 500GB external drive (with shared media files) to a portion of the Time Capsule internal hard drive. I assume this would require a partition of the Time Capsule drive. If not, would the sparse file from the various computers being backed up need to be copied to the external drive as part of the RAID1 setup? This seems like overkill for the Time Machine backup, but it would cover the media files.  

    The complexity with this idea is the software has to run from a Mac computer on your network.. so you need a Mac turned on, probably most of the day.
    It isn't possible to partition the TC although you can create a image area.
    The software would have to copy the material, that means all files to be copied, go from USB drive, back to the Mac, then back to the TC, and written to the drive. In other words you have just added Network congestion, although a proper incremental backup type software will not actually use a lot of capacity.
    Finally it will be slow.. network drives are slower than internal drives. Well USB connected drive is much slower than the same drive connected directly to the computer.. and if the drive is connected directly to a computer it can be shared with the network.
    http://www.anandtech.com/show/4577/airport-extreme-5th-gen-and-time-capsule-4th- gen-review-faster-wifi-/4
    Read carefully the speed of the USB drive plugged into the TC.

  • HT201250 If using Time Machine with an external drive, can I just use it occasionally for back up, say once per week and have it disconnected in between backups?

    When using TM with an external drive, can I connect and use it occasionally for backup and disconnect it between backups, say one backup per week?  Or does it need to be connected all the time when the computer is on?

    TimeMachine works better if it's nearly always connected.
    For addtional backup like what your needing, consider a bootable clone in addition to TM.
    Most commonly used backup methods

  • Can I use a 2tb external drive with Time Machine to backup my Mac Mini (256gbSSD + 2tbHDD)?

    Can I use a 2tb external drive with Time Machine to backup what I have on my Mac Mini?
    My Mac Mini has one 256 SSD and one 2tb HDD. I want to use Time Machine to do a backup of everything.
    Would an external 2tb My Passport Drive by Western Digital work for the backup?
    It seems like it would not work because the total storage on the Mac Mini is 2304 gigabytes (SSD + HDD).
    And the external Western Digital drive is only 2048 in gigabytes versus 2304 gigabytes the Mac Mini has.

    No. A Time Machine backup drive should have at least twice the capacity of the drive it backs up. You would need at least a 4 TB backup drive for Time Machine.
    Might I suggest as an alternative that you not use Time Machine but a third-party backup utility that simply overwrites older files with new ones such that the backup drive can be the same capacity as the drive backed up.
    Suggested Backup Software
      1. Carbon Copy Cloner
      2. Get Backup
      3. Deja Vu
      4. SuperDuper!
      5. Synk Pro
      6. Tri-Backup
    Others may be found at MacUpdate.
    Visit The XLab FAQs and read the FAQ on backup and restore.  Also read How to Back Up and Restore Your Files.

  • Can I boot from an external drive with a "Virtual CD"

    I just purchased a Hitachi LifeStudio external hard drive for use as my Time Machine backup. When I plugged it in to my MacBook running 10.6.4, I realized that it had one of those "Virtual CDs" that contained the manufacturers crapware, similar to Western Digital's MyWare or whatever its called. It shows up in disk utility as an actual separate disk and not just another partition that can be wiped.
    I reformatted the drive using GUID and and created 3 HFS+ Journaled partitions. One was going to be for the 10.6 installer, one for the 10.6 boot, and one for my time machine backup. I restored a 10.6 install dvd disk image I created using disk utility to the 10.6 installer partition (with erase destination checked) then option booted my mac and the partitions did not show up. The only thing I could see was my internal hard drive.
    I have done this many times before and it has always worked so Im trying to figure out what Im doing wrong. The only thing I can think of is that the "Virtual CD" that Hitachi put on this external drive is stopping the Mac from seeing the bootable partitions I created. I even went into system preferences>startup disk and blessed the 10.6 install partition. That didn't work either, the computer just booted to my internal drive.
    So my questions are. Is it because of this "Virtual CD" that I can't boot from my external drive? If so, is there a way around it? I already searched their web site and emailed their tech support asking for a firmware update to remove the virtual cd.
    Thanks in advance.

    Yes, it's a known issue. You've already referred to the issue with WD systems. WD has a long list of products that are either not compatible with Macs or won't boot a Mac.
    There are practically no problems with bare drives, but once installed in an enclosure there is no guarantee that the package will function as a bootable device. This is especially the case if the manufacturer uses some sort of "virtual" scheme intended for using the device as a sort of one button backup device.
    External drives don't have to specifically say anything about being Mac bootable or compatible. It's up to the consumer to verify compatibility and usability.

  • How to use Time Machine with an external drive?

    Hi…I’m new to this, I hope someone can help me=)
    I’m trying to back up my Macbook Pro 10.6.8 using Time Machine with an external drive Seagate Backplus Slim. I’ve tried several solutions that I’ve found through different forums but still wouldn’t work.
    Every time I opened Time Machine, it has this appearance:
    Then when I click “Select backup Disk”, it goes on like this:
    And after I click “Set Up Time Capsule”, it has this:
    It keeps saying that it couldn’t find AirPort wireless, even though I have good WIFI connection.
    Anyone know what I should do? Please help….Thanks everyone

    Ayuphie ~ In your Time Machine Preferences panel, slide the OFF-ON switch to the ON position:

  • Computer won't startup after Tiger install with Maxtor external drive

    I just upgraded to Tiger on my G4 Dual 450. The computer will not startup with my Maxtor 200 MB external hard drive connected. When it is connected I get a message to restart my computer. The computer starts up and runs with no problems when the Maxtor is not connected. When I connect the Maxtor after the computer is started I get a gray screen to restart my computer. I can connect the Maxtor to another G4 in my office with no problems. Does anyone have any ideas?
    G4 Dual 450 MHz   Mac OS X (10.4.8)  

    Hi, platteau1. Welcome to the Discussions.
    You wrote: "When it is connected I get a message to restart my computer."You are describing the following message:
    That indicates a kernel panic.
    1. First, I suggest you contact Maxtor as there may be a problem with the external drive or it may require a firmware update.
    2. Next, see my "General FireWire troubleshooting" FAQ for advice that may help you troubleshoot the FireWire drive. It may be as simple as a bad FireWire cable or FireWire port on your Mac.
    3. Finally, see also my "Resolving Kernel Panics" FAQ. This FAQ includes step-by-step instructions for identifying and resolving some of the most common causes of kernel panics. The FAQ is a roadmap: start at the beginning and work systematically through the end, i.e. the "If all else fails..." section.
    Good luck!
    Dr. Smoke
    Author: Troubleshooting Mac® OS X
    Note: The information provided in the link(s) above is freely available. However, because I own The X Lab™, a commercial Web site to which some of these links point, the Apple Discussions Terms of Use require I include the following disclosure statement with this post:
    I may receive some form of compensation, financial or otherwise, from my recommendation or link.

  • NVIDIA OpenGL driver lost connection with the display driver

    Alienware M14x Laptop
    Windows 7-pre 64-bit
    8gb ram
    3gb Video: NVIDIA GeForce GT 555M
    Intel i7 2760QM
    AE CS4
    AE keeps crashing. I get the following message while doing something as simple as scrubbing through the timeline, or changing opacity of a layer. in 1080p, I have a picture layer, a solid, some color corrections, and that's it. i just got this new computer and i have never had this problem on my old computer.
    this message appears after AE crashes."The NVIDIA OpenGL driver lost connection with the display driver and is unable to continue. The application must close."
    this message appears in the taskbar: "Display driver stopped responding and has recovered. Display driver NVIDIA Windows kernel Mode Driver, Version 267.21 stopped responding and has successfully recovered"
    any ideas on how to stop AE from causing my display driver to stop working?
    Thanks, Ramzi Rebeiz

    For anyone picking up this thread (it's probably too late for rrebeiz40 by now!) I have come across a simple but apparently very effective tip that has solved the 'OpenGL driver lost connection' issue for many people using various NVIDIA with various Adobe progs (incidentally a lot of these seem to crop up on Dell machines, especially Notebooks).
    (It fixed my issue with Premiere Pro CS4 - GeForce GT 555M on Win 7 Ultimate 64-bit, Dell XPSL702X).
    It's posted on http://forum-archive.developer.nvidia.com/index.php?showtopic=5331&st=40 (look for the last post, No 50) as follows:
    THIS FIX APPEARS TO WORK...found on an Adobe forum
    "This issue led me to this fix: go to NVIDIA Control Panel --> Manage 3D Settings --> Global Settings, and switch "Power Management Mode" to "Prefer Maximum Performance" (the default "Adaptive" setting seemed to be the culprit). And that's it! The key here is changing the "Global" setting, as my individual programs were already set to "Prefer Maximum Performance." I can cause the error to reoccur by changing back to "Adaptive."
    Otherwise lots more ideas on this site: http://www.instructables.com/id/How-to-Fix...Nvlddmkm-Error/
    My PC has been running for 2 days now. I only put the top fix in for now. Feel happier I have more options if need be though.
    Inserted from <http://forum-archive.developer.nvidia.com/index.php?showtopic=5331&st=40>
    It worked for me

  • JDBC receiver error Cannot establish connection with the registered driver

    Hi Expert,
    I am constructing a proxy to JDBC scenario. And I am getting error saying "
    Message processing failed. Cause: com.sap.engine.interfaces.messaging.api.exception.MessagingException: Error when attempting to get processing resources: com.sap.aii.af.lib.util.concurrent.ResourcePoolException: Unable to create new pooled resource: DriverManagerException: Cannot establish connection with the registered driver. oracle.jdbc.driver.OracleDriver returns: The Network Adapter could not establish the connection. : SQLException: The Network Adapter could not establish the connection"
    I can get into my Oracle database using TOAD with same IP address, user name and password. Could anybody tell me what should I do? Thanks a lot!
    Charles

    Hi,
    Check with your network team, network conenction between PI and Data base not working , Network team have to open Data base system ports inorder connect PI System.
    check with Basis team about network connectivty,like they are bale to ping Data base server ip or not.
    please go through below thread,
    SQLException: Io exception: The Network Adapter could not establish the con
    regards,
    ganesh.

Maybe you are looking for