Can MXE 3500 stream MPEG2 directly to DMP4310?

I have a TCS intergrated with MXE 3500. I'm trying to use the IPstream Distribution profile to stream MPEG2 to DMP4310.
I utilize the following encoder in MXE 3500 ( H.264 and MPEG), use the following Distribution - IPStream (multicast IP address) and Output (MPG). Out Distriburion is working well, except the IPStream Distribution to DMP4310 is not working. I tested the multicast with my existing AS8100 to make sure it not the multicast setup.
Anybody has the same set up in your enviroment?
Many thanks.

This thread is Answered.
Create a job profile and use H264 Encoder -IP_Streaming, create a distribution profile under IP_Stream (multicast IP and port)
Test IP capture by installing VLC in MXE3500.MXE3500 cannot capture multicast TS streaming,so I decided to run a TCS Unicast Streaming.
Lastly, create a live event.
Run VLC, open network stream, enter udp://@MulticastIPAddress:port
There you go.....

Similar Messages

MXE 3500 Integration with DMS VMware

Can MXE 3500 integrates with Show and Share 5.3.0 Vmware setup?
Is there any chalanges for integration?

Hi Nicolas,
Thanks for the update..
We are trying to integrate TCS and SNS with MXE.
We are refering the below document from SNS with MXE..
http://www.cisco.com/en/US/docs/video/mxe/3500/sw/3_x/3_3/integration/note/integ_mxe33_sns.html
and the below document for TCS with MXE.
http://www.cisco.com/en/US/docs/video/mxe/3500/sw/3_x/3_4/cxs_solution/configuration/guide/cxs_config_guide.html
We have tried to upload one video in SNS and its went to MXE for convertion, MXE has converted this video successfully and sent this video to SNS. This is working without any issues.
But we are trying with TCS, there we are facing one issue.
TCS is recording video and sending it to MXE, we can see this particular video in Job status monitor in MXE but its not converting succesfully, the job status is showing "fail" as a status.
What will be the issue and how we should troubleshoot?
Regards,
Nishant

Can I stream music directly from my Ipod Touch 4g to my airport express?

Can I stream music directly from my Ipod Touch 4g to my airport express?

If Airplay is avaialble on your iPod Touch and it should be, and your AE is connected to a stereo system or to some speakers, yes.

Can I stream things directly from the time capsule to my AppleTv without using my computer?

I have an older MacBook and I'm worried about the storage so I want to get things moved to a Time Capsule. I was just wondering if I can stream things directly from the Time Capsule to the AppleTV without having to store them in iTunes on my computer and play them off of there.

You cannot stream from a TC .. it is not a media device.. you can store movie files on the TC but you still need to run the computer to play them.
Depending on how you connect this can cause dramatic slowdowns.
A WD Live TV can play raw movie files from a TC.. because it is not a media streamer which is all the ATV is, it is a full media player.

IMac (on Ethernet) Can No Longer Stream to Airport Express (on WiFi)

After years of reliable service, all of a sudden I cannot stream music from iTunes on my iMac, via my Airport Express, to my stereo system.
First, a bit about my configuration:
   * iMac connected via Ethernet to a wireless router (D-Link DIR-655).
   * iMac Airport (WiFi) is turned off.
   * D-Link sets up a wireless network, and Airport Express joins the network.
   * Airport Express does not set up its own network, it's simply a client of the existing D-Link wireless network.
   * iTunes "sees" the Airport Express, and can stream audio via AirPlay.
   * iPad also joins the wireless network, and also can stream to the Airport Express via AirPlay.
   * iMac running 10.6.8, with all software updates applied.
   * Airport Express running latest firmware (7.6.1).
Well, that was a few days ago, when "it just worked". But for some unknown reason iTunes could no longer "see" the Airport Express.
So I took my Airport Express to the Apple Store and they did a Factory Reset, but it did not solve the problem. I figured my rather old Airport Express was failing, so today I bought a new one. The symptoms have changed a bit, but even after spending an hour on the phone with AppleCare, it doesn't work properly.
Now, the only way the iMac can stream to the Airport Express is if the iMac also joins the wireless network. In fact, now with Airport turned OFF on the iMac, the Airport Utility cannot see the Airport Express. But here's another weird thing: when I use the IP address of the Airport Express, the Airport Utility CAN connect with and manage the Airport Express, even with Airport turned OFF on the iMac!
I should also mention, the iPad has no issues whatsoever connecting to the D-Link's wireless network and streaming music to the Airport Express.
This all seems like something might have changed on the D-Link wireless router. But for the life of me, I cannot figure out what setting(s) on the router might allow the iMac - over Ethernet - to stream audio to the Airport Express.
Another thing. When I have Airport turned on on the iMac, it can "see" and stream to the Airport Express, but the music has very frequent drop-outs. Could this be related to the fact that the iMac has two IP addresses (one on Ethernet, one on WiFi)?
My goal is to get things "back to normal", where I can turn off Airport on the iMac, and all LAN and WAN traffic from the iMac goes over Ethernet. I have a few questions (for now :-)
   * Since my iMac has two connections to my LAN using two IP addresses (Ethernet & WiFi), is that likely to cause any issues?
   * When two computers join the same wireless LAN, can they effectively talk directly to one another, or does the wireless router need to be involved every time one computer sends a TCP or UDP packet to the other?
   * Do routers (or the DIR-655 in particular) tend to have any firewalls or policies that control connections on the LAN between Ethernet and WiFi clients?
   * Since AirPlay uses TCP port 3689 and UDP port 5353, would the DIR-655 need any special configuration to "open these ports" so an Ethernet client can connect with a WiFi client?
So, any help would be most appreciated!
Thanks!
Jim

I am having a very similar issue. I use my Airport Express (AX) to stream music from the computers on my network to my stereo via Airplay. I have AX set up to wirelessly join my existing wireless network, which uses a D-Link DIR-655 router hooked to a Time Warner cable modem. I can succesfully connect all of my wireless devices via Airplay, through iTunes to my AX, including two laptops and an iPhone. However, my primary desktop PC, which does not have a wireless card is linked directly via ethernet cable to my D-Link router, and it is not able to see my AX. Similar to your case, I can see the Airport Express from my PC through my Airport Utility by directly typing in the IP address. Note that the AX set-up option to allow Ethernet clients is checked. I also noticed that my laptops will stop detecting AX if I directly connect them to my D-Link router via Ethernet and turn off their wireless cards. They will resume detecting AX when I turn their wireless connections back on. I have tried every conceivable setting of my D-Link router to no avail.

Cisco MXE 3500 Cluster Help

Hello
i need help for my Cisco MXE cluster . I have already installed RM license and RN licesnses and all are installed successfully. I need to know what are the next steps?. I have 1 X RM and 4 X RM , how can i add my 4 X RN to my cluster to can see RM successfully?.
Thank you

Hello Mohamed,
The main step needed after licenses are properly applied is to add each RN as a host in the RM GUI Administration.
You can actually follow the full MXE configuration tasks as documented at:
http://www.cisco.com/en/US/docs/video/mxe/3500/sw/3_x/3_3/admin/guide/tasks.html
This document is also valid for standalone deployments, but you will notice that any extra step or different step needed in clustered deployment will be added in a note starting like:
"Note In a clustered deployment..."
I hope this helps,
Marco

MXE 3500 Reporting

Hi,
We have an MXE3500 installed. There is a reporting requirement and the focus is on 3 prime areas -
(1) How much activity is flowing through the service
-Total number of Jobs per day
- total processing hours per day
(ii) What is the Peak traffic profile
- Peak volume of jobs at any point during the day
- Maximum wait time for a job during the day
(iii) Service Outages
-Number of service outages during the day
-Number of job failures during the day
I looked the Reporting eature available on the MXE webui (Job Custom Report & Task Custom Report). ITs not giving the desired results(Or maybe I dont understand it correctly). Can anyone suggest a way I can pull a report which will give me the above details? Many thanks
Zeeshan

Hi Nicolas,
Thanks for the update..
We are trying to integrate TCS and SNS with MXE.
We are refering the below document from SNS with MXE..
http://www.cisco.com/en/US/docs/video/mxe/3500/sw/3_x/3_3/integration/note/integ_mxe33_sns.html
and the below document for TCS with MXE.
http://www.cisco.com/en/US/docs/video/mxe/3500/sw/3_x/3_4/cxs_solution/configuration/guide/cxs_config_guide.html
We have tried to upload one video in SNS and its went to MXE for convertion, MXE has converted this video successfully and sent this video to SNS. This is working without any issues.
But we are trying with TCS, there we are facing one issue.
TCS is recording video and sending it to MXE, we can see this particular video in Job status monitor in MXE but its not converting succesfully, the job status is showing "fail" as a status.
What will be the issue and how we should troubleshoot?
Regards,
Nishant

MXE 3500 v3.3 admin user role

Hi,
I am currently work with a MXE 3500 v.3.3. When I loged into the system using GUI, I don't get the Administration role in toolbox. My user is admin. So please help me, how can I give admin user the admin role permission.
Please see the attached file for details.

You were probably trying to define multiple domain indexes on the same column using identical indextypes. How many indexes you have on table_colum?

MXE 3500 v3.3 Host ID changed

Hi,
I am working with MXE 3500 v3.3. Earlier I have installed the server and after that I have received the license file base on the "HOST ID" from cisco. But I have to install the server again and now I have noticed that the "HOST ID" has been changed. So the earlier license file shows invalid for the same server. I can not request for the license file to cisco again as it has the same PAK. So please help me, if there is any work around to install the license on the same server.

I had the same issue after upgrading from 10.7.2 to 10.7.3 and changing my main SSL cert.
The solution was to make sure the correct cert was listed in:
/etc/openldap/slapd.conf
as well as:
/etc/openldap/slapd.d/cn=config.ldif
It looks as though the slapd.conf file gets updated properly when you select an SSL cert in the Server Admin app, but the cn=config.ldif does not. That is the one that was hanging my server up.
Hope this helps!

Orarrp can't print pdf file directly to printer

oracle remote print utility (orarrp) can't print pdf file directly to printer.
we expect orarrp utility can handle ".rrpa" file (i.e. pdf file generated on the application server) by directly print the file to the client's printer, i.e. invoke the acrobat reader on the client side, display the the printer selection dialogue, after confirmation print the pdf file, then the acrobat reader close automatically nicely.
However we are disappointed as the acrobat reader startup and display the pdf file content but does not print and does not close.
After testing the problem several times, there are some findings:-
Finding (A):-
(a) for the success of direct printing of pdf file, a physical path must be provided; we have tried 2 methods:
1) using drag & drop to copy the pdf file directly to the browser
2) open pdf file in the browser directly using browser menu-->File-->Open.
(b) for the failure of direct printing, a virtual path is involved and we have also tried 2 methods:
1) when web.show_document() is used
2) enter the url to the URL bar of the browser,
eg. http://appsvr.com:7777/report/test_printout/APPSVR1094707.rrpa (this is a virtual path/url)
Finding (B):-
(a)when the physical path is used, a temporary pdf file is generated in the same directory where the rrpa file exists in the application server,
e.g. in application server: d:/printout/yyy.pdf is generated for d:/printout/xxx.rrpa when direct print occurs
(b) however when the virtual path is used, there is no such temp "pdf" file generated and direct print failed.
May be when virtual path is used, orarrp utility don't know where to generate the temp "pdf" so direct print doesn't occur.
So, anyone has similar experience or further queries or has solutions, please join.
Thanks for your attention.

Hi,
It is really late to give response this post. But still who ever refering to this post for the same issue this solution is useful for achieving same in background:
Even same can be used in smartforms, for getting spool request in PDF format as well which will decrease the size of file when printing in SAP printer.
ct_tline is PDF output:
DATA: lv_pdfsource TYPE xstring.
FIELD-SYMBOLS:<p> TYPE x. " <p> type any.
LOOP AT ct_tline INTO cs_tline.
ASSIGN cs_tline TO <p> CASTING TYPE x.
CONCATENATE lv_pdfsource <p> INTO lv_pdfsource IN BYTE MODE.
ENDLOOP.
* ->Create spool request in PDF format
CALL FUNCTION 'ADS_CREATE_PDF_SPOOLJOB'
EXPORTING
    printer = 'LOCL'            "Printer name supporting PDF device type
*   DEST     =
    pages    = 1
    pdf_data = lv_pdfsource        "XSTRING internal table
*   NAME     =
*   SUFFIX1 =
*   SUFFIX2 =
*   COPIES   =
*   PRIO     =
    IMMEDIATE_PRINT         = 'X'
*   AUTO_DELETE             =
*   TITLELINE               =
*   RECEIVER =
*   DIVISION =
*   AUTHORITY               =
*   LIFETIME = '0'
* IMPORTING
*   SPOOLID =
* EXCEPTIONS
*   NO_DATA = 1
*   NOT_PDF = 2
*   WRONG_DEVTYPE           = 3
*   OPERATION_FAILED        = 4
*   CANNOT_WRITE_FILE       = 5
*   DEVICE_MISSING          = 6
*   NO_SUCH_DEVICE          = 7
*   OTHERS   = 8
IF sy-subrc <> 0.
* Implement suitable error handling here
ENDIF.

Can I cut and paste directions obtained via maps into a word doc or something so I can see them if I can't connect to the internet

Can I cut and paste directions form maps into a word doc - or save it somewhere on my iPad so I can access it when I can't access the Internet?

Take a screen short.
Simultaneously press the Sleep and Home button. You will notice an on-screen flash. If you have sound enabled, you will hear a camera click.
The screen shot is stored in Camera Roll.

How can I transfer photos from my comp to my ipad2.I have the connection kit and can transfer photos that are direct from camera BUT if I transfer photos from comp to card it will not recognize them ????

how can I transfer photos from my comp to my ipad2.I have the connection kit and can transfer photos that are direct from camera BUT if I transfer photos from comp to card it will not recognize them ????

To sync photos from a Mac or Windows PC to your device using photo applications
Make sure you have the latest version of iTunes installed.
In iTunes, select your device's icon in the Devices list on the left.
Click the Photos tab.
Choose "Sync photos from."
On a Mac, choose iPhoto or Aperture from the pop-up menu.
On a Windows PC, choose Photoshop Album or Photoshop Elements from the pop-up menu.
Note: Some versions of Photoshop Album and Photoshop Elements don't support collections. You can still use them to sync all your photos.
If you want to sync all your photos, enable the option for "All photos, albums, events, and faces." If you want to sync photos from only some albums, events, or faces, enable the option for "Selected albums, events, and faces" and then select the albums you want. If syncing on a Mac with iPhoto version 6.0.6 or later, you may enable the option to "Include videos" to sync videos directly from iPhoto to your device. (Requires iOS 3.0 or later).
Click Apply.
To sync photos from a folder on your hard disk to your device
Drag the images you want into a folder on your computer. If you want images to appear in separate photo albums on your device, create folders inside the main folder and drag images into the new folders.
In iTunes, select the device icon in the Devices list on the left.
Choose "Sync photos from."
Select Choose Folder from the pop-up menu and choose your main image folder.
Click Apply.

I can no longer purchase music directly from the Apple TV. I can still buy TV shows and movies but no music.....

I can no longer purchase music directly from the Apple TV. I can still buy TV shows and movies but no music.....my iTunes match is there.

Welcome to the Apple Community.
Have you tried restarting the router, the Apple TV and iTunes.

HT4363 I can no longer stream my iTunes into my Apple TV. Help!

I can no longer stream my iTunes into my Apple TV. It has worked before, but Apple TV is not recognizing my iTunes library any longer. It keeps telling me to make sure it's turned on on my computer. It is. And yes, the accounts match, etc. But it no longer recognizes my iTunes library. I can play all the stuff purchased through iTunes fine. I just can stream my main library any longer. Very very frustrated.

Welcome to the Apple Community.
Have you tried restarting the router, the Apple TV and iTunes.

5th generation ipod not detected by my windows xp. works fine on other pc. performed necessary steps to remove and reinstall itunes but having same issue. is there a driver i can download to pc then direct to that specific location when installing?

5th generation ipod not detected by my windows xp. works fine on other pc. performed necessary steps to remove and reinstall itunes but having same issue. is there a driver i can download to pc then direct to that specific location when installing?

I have a similar issue - my iPod nano connects and is visible in Device Manager yet invisible in My Computer and iTunes. I've tried everything I can possibly think of to try and solve this myself, all in vain.
Mine is a nano 4G. I've been using it for quite some time without the slightest problem. I have been using WINAMP instead of iTunes to manage my darling nano.
Then, one fine day I bought a new computer and the nano would not show up in My Computer, though the nano display shows "Do not disconnect". On my old computer it worked (and still works) absolutely fine with win XP as well as with win7 (the later I currently use on my new/problematic computer, which I bought last summer and that's how long I've had this problem).
Of course, after several first attempts I gave up and installed iTunes. I've tried using the Apple support article "iPod not recognized in 'My Computer' and in iTunes for Windows":
- reset
- fully charged,
- cable works fine on two other computers
- in normal or disk mode makes no difference
- tried to find anything useful in the diagnostics mode
- reinstalled iTunes several different times since then to the latest version
- I've unplugged every other USB device except for my mouse and keyboard and tried several different USB ports on my motherboard (USB 3.0 and conventional), as well as trying different USB- related options in my BIOS.
- I've never used any Mac with this ipod
- I've tried fiddling with the win7 Services by stopping and restarting them and of course
- uninstalling the iPod drivers in Device Manager. After such an uninstall the ipod would automatically be recognised and "ready for use", i.e. being invisible in My Computer.
- Attempted to find any possible third-party conflict with msconfig or the possibility that my ipod is being confused for a network drive (for which I've disconnected my HDD, leaving only my SSD with the OS).
Sometimes, iTunes would note that iPod service (or something, can't remember exactly) failed to install properly and asked to try and repair it. I would click YES! and voila - no change! The ipod would rarely show up in iTunes on my problematic computer like this:
iTunes would warn me that the nano would need restoring so I would try and do it on my haunted machine upon which iTunes would freeze like you seen in the picture.
Despite this, I've updated and restored the nano on my father's computer to the latest version without any problems. This though, did not solve my problem in any way.
I can load music to my nano through my old computer (which for me is a real pain and hassle) and the gadget works normally in terms of its disconnected functionality.
I've taken my nano to the local service for repair and they said it was fine. Mercifully, they didn't charge for the diagnostics service (gee, thanks for not ripping me off!).
Here are two screengrabs from my Device Manager
and Devices and Printers screens on my comp:
That is my sad story as far as I can remember. It's most likely something with the drivers or something along those lines though I'm out of ideas at this point.
If you think you have any idea PLEASR HELP, I'M DESPERATE!

Can MXE 3500 stream MPEG2 directly to DMP4310?

Similar Messages

Maybe you are looking for