Can my iMac OSX 10.8.5 connect to my Canon PIXMA 452 wirelessly

My iMac doesnot connect to my Canon Pixma 452 Printer when it has for the last 3 months?

Hello there, lbaer.
The following Knowledge Base article offers up some great recommendations for troubleshooting printer issues:
Troubleshooting printer issues in OS X
http://support.apple.com/kb/ts3147
Thanks for reaching out to Apple Support Communities.
Cheers,
Pedro.

Similar Messages

My new Canon Pixma 7250 wireless printer can no longer find my wireless network. My MAC is, Yosemite 10.10.2. I've run diagnostics and Canon LAN printer setup routine many time. Is there a solution? Can anyone help?

My new Canon Pixma 7250 wireless printercan no longer find my wireless network. (It worked fine until recently) I have a Yosemite 10.10.2. I've run diagnostics and the Canon LAN printer setup routine many times. Is there a solution? Can anyone help?

Turn of the MG and unplug the power cord. Leave it off for about a minute and then reconnect the power cord and turn the power back on. Wait while the device attempts to reconnect to your wireless network - the blue wifi symbol on the MG will flash and then stay on once it has connected. If it keeps flashing then you will have to reconnect the MG to your wireless access point via the control panel on the MG.

Canon Pixma MG6120 Wireless printer - can't get to work with AirportExtreme

Canon Pixma MG6120 Wireless printer - can't install mg6100swin104ejs.exe 64 bit wirelss driver on Windows 7 64bit when printer is registered to 10.0.1.X Airport Extreme. Even if I enable Advanced Port Mapping, Printer Sharing the Canon software doesn't recognize the printer if it is registered wirelessly to the Airport Extreme. Canon senior tech support and Apple senior tech support don't know how to help. Any advice for someone who was able to get a Canon Pixma Printer to work with their Airport Extreme from a Windows 7 64bit PC also connected to 10.0.1.X subnet? Your advice is greatly appreciated. The printer once online is pingable at 10.0.1.9 and I can see SD cards and browse photo's just can't get the Canon software to wirelessly activate/install.

To print from an iPAD using the Lexmark S300 series,you need to download the LexPrint app from this link: LexPrint
Hope this helps.

Please help me, How to connect my printer Canon pixma MP160 to my mac OS X Yosemite?

please help me, How to connect my printer Canon pixma MP160 to my mac OS X Yosemite?

You do not need the Setup Assistant; in fact, you do not need any software on an external hard drive. I have two LaCie's; I erased the drive as soon as I plugged it in. You will need to format it anyway because most hard drives come Windows formatted. So, if you only want to use it with the Mac, highlight it in Disk Utility and choose Mac OS Extended (Journaled) as the format and the GUID Partition scheme under Options. While doing that, it will erase the drive (and get rid of the LaCie software) - once finished, your drive is ready to use for Time Machine or any other backup plans you have for it.

My Dell Inspiron 1525 is USB connected to my Canon Pixma MX 392 printer, but is "not detecting".

My Dell Inspiron 1525 laptop is USB connected to my Canon Pixma MX392 multifunction printer. Though the
printer is functioning properly in all respects, a message is showing that my laptop "cannot detect" the printer.
At the same time I'm receiving a message (wizard?) "Found New Hardware - Windows Needs to Install Driver
Software for Your Universal Serial Bus (USB) Controller". My Printer folder shows my Canon is "ready",
and the Port is shown as "USB..Virtual printer port for Canon MX390 series Printer". My Device Manager
folder lists the Canon printer and fax under "Printers", and under "Universal Serial Bus (USB) Controllers"
are listed: MX390 series (1 time); Universal Serial Bus (USB) Controller (7 times); Unknown device (7 times);
USB Printing Support (2 times). I've tried unistalling and re- installing everything associated with the printer,
but get the same results. As I've stated the printer is functioning fine, but the "incessant" appearing of the
message, "Found New Hardware, etc." is extremely annoying. When I follow the "wizard's" instructions to,
"locate and install driver software (recommended)", I'm finally told to" insert the disc that came with your Universal Serial Bus (USB) Controller". I don't have any discs that came with either the printer or laptop. Is
anyone able to make any sense of this...and, hopefully, offer help in getting rid of the "Found New Hardware"
message. Many thanks!

I'm not sure the error is related to your printer.
http://www.tomshardware.com/s/install+driver+universal+serial+bus+usb+controller/
Have you tried going to the Windows Update software program and seeing if there are any udates related to your message?
John Hoffman
Conway, NH
1D Mark IV, Rebel T5i, Pixma PRO-100, MX472

I need to connect my Chromebook to my Canon PIXMA MG3520 wireless printer

I'm having problems connecting my Chromebook to my Canon PIXMA MG3520 wireless printer. Because of the Chrome OS, it will not connect like Windows or Mac. I need help before retire, please.

Hello Bama-85,
You are correct, printers do not install the same way on Chrome OS. I looked on the Google Cloud Print site and your Canon printer is indeed supported. Follow this link to setup your cloud ready printer.
I haven't setup a Canon printer via Google Cloud Print, but I assume it's as easy as setting up HP's printers on the print service.
Miles
HP Employee

Cannot get my iMac OSX 10.5.2 to print on canon mf4412

Hi All,
I cannot get my iMac OSX 10.5.2 to connect and print on canon mf4412. I installed UFRII_V224_MacOSX_uk_EN driver but to no avail. iMac doesn't recongnize the printer and throws client connect error. I tried the printer on Win XP & works fine.
Can somebody please help me resolve this issue?
Thanks!

I'm having the exact same problem. Have downloaded the drivers from both the singapore and uk websites of canon and yet it doesnt print.

How can i connect my printer canon pixma mg7150

Hello,
I don't find the good driver for my printer CANON PIXMA MG7150, and i use a usb cable.
Is it good ?
Thanks

I have been setting up the same printer this week, with a USB cable to my iMac. I have taken Mac printer drivers from the Canon site. Here is a link that I used.
http://www.canon.co.uk/Support/Consumer_Products/products/Fax__Multifunctionals/ InkJet/PIXMA_MG_series/PIXMA_MG7150.aspx?type=download&softwaredetailid=tcm:14-1 091005&os=OS%20X%20v10.9&language=EN
Apple have notified that they have newly updated printer drivers for this printer, which you can download if you have the other drivers in place.
Hope this helps.

IPad connecting to a Canon PIXMA MG6220 printer?

I have a first gen iPad that I want to connect to a printer. I purchased a Canon PIXMA MG6220 "all in one" printer. I can print photos from the iPad by selecting the "print" option on the photo page. But I cannot print emails or email attachments. When I select the "print" option on the email page, the iPad tells me that it cannot find an AirPrint printer. Clearly, the iPad can find the Canon (an AirPrint printer) from the photo page. Has any one else had this problem with a Canon? How do I print emails and email attachments? Thanks. Hobbes from CO

Update the firmware on the printer.

Problem connecting Canon Pixma IP5200R wirelessly

Hello
My problem is this: I have successfully set up my IP5200R printer to print wirelessly in conjunction with my iMac and Airport Extreme. However, if I temporarily 'switch off' the network's WEP protection which I have to do from time to time to allow a pesky laptop PC to use the wireless network, when I later reactivate the WEP protection the printer is no longer detected and I get an error 306 when I try to print anything. I then have to reinstall the printer using the USB cable to get it back on the wireless network which is very annoying. Is it possible to toggle between WEP off and WEP on without having to reinstall the printer each time?
Many thanks, and apologies for any clumsy descriptive terms used to describe this problem. I hope you get the general idea!

Modesto:
I have a Pixma 800 and I assume setting up yours is the same as mine. You have to connect the printer to the computer via USB cable directly and set it up wired with the setup disc that came with the printer. After you've done this disconnect the USB cable from the computer and connect it to the USB port of your router. In my case, it is the Airport Extreme station. I'm not sure after this but I would go to System Preferences under the Apple and then click on printer and Fax. If you do not find the printer there, click on the "+" and after a time, the printer should show up because the printer driver has been downloaded. I don't know if your printer driver has been downloaded with the Apple OS software. Then click on the Pixma 800 which should show up and then click add. I'm not sure about the rest but you must first make a direct USB connection between the printer and the computer. I hope this starts you on the way.

The computer is not seeing the usb connection to my canon Pixma IP 90 the USB port states Generic US

my computer shows generic usb hub and does not recognize my canon Pixma IP 90 printer when pluged into the usb port how to configure the usb port

you're in HP forum ....hehehe
not Canon...
Although I am working on behalf of HP, I am speaking for myself and not for HP.
Love Kudos! If you feel my post has helped you please click the White Kudos! Star just below my name : )
If you feel my answer has fixed your problem please click 'Mark As Solution' and make it easier for others to find help quickly : )
Happy Troubleshooting : )

Two 1st Generation iMacs using 1 Broadband Cable connection - Best way?

Hi guys,
I have a snow iMac (600Mhz) running 10.2.8 - I have it set up with Virgin Cable Broadband (formerly Telewest/NTL using a Motorola Surfboard Cable Modem), my mum has passed us her old Tangerine iMac (400Mhz) also running 10.2.8 - I currently have both set up in one of our bedrooms, they are about 2 metres apart on seperate desks.
I have asked this to quite a few people but am getting different answers all the time so I am hoping you guys here can help in giving me a definitive answer:
What's the best way for me to get both of these iMacs on via by Cable connection? - I don't want wireless, I just want wired ethernet.
Some people are insisting I need a wired router similar to this:
http://www.broadbandstuff.co.uk/productinfo.php?productsid=225
Whilst others are saying that I just need a switch device similar to this:
http://www.broadbandstuff.co.uk/productinfo.php?productsid=113&osCsid=7b23b40476276b3714287fcad8b20a38
Can anyone confirm please?
Thanks

I know I have closed this thread off, but wanted to
ask Alan one more question...
Did you have to recontact NTL when you got your
router to supply them with the new code on the router
before it would work?- A guy at my work has said I
will need to do this, is this correct?
Hello IntelMacMini,
No I did not contact NTL about anything. I think you may have to do this if this is the first time you have made any connection to the internet.
I presume you already have one computer connected to the broadband modem as I had.
All I did was unplug the ethernet cable from the modem to the computer and plugged it into the internet port on router and then ran an ethernet patch cable from one of the numbered ports to the computer. Then I switched on the router and followed the instructions that came with the router until it was up and working and connected with the internet.
Then I connected a patch cable to another numbered port on the router and plugged it into the ethernet port on the second computer.
Next switched off both computers, the router and the modem in that order.
Then switched on the modem waited until all was working ( lights steady ), then the router until all the right lights were steady, then the first computer and checked that it connected to the internet, and finally the second computer and checked the connection.
With the third old g3 powerbook OS 9.2.2 I just set the TCP/IP to connect via ethernet and configure using DHCP server and plugged it in without switching anything off and it worked first time.
It sounds a bit complicated but if an old technophobe like me can do it anyone can.
Hope this helps,
Alan
Message was edited by: Alan Bishop2

HT4600 where can I find the WPS button on Time Capsule (for connecting to a Canon printer)?

I can´t find the WPS button for connecting to a Canon printer wireless. Somebody who can help me?

There is no WPS button on the Time Capsule.
You might be able to get the printer to connect using the following method:
Open Macintosh HD > Applications > Utilities > AirPort Utility
Click the Time Capsule icon, then click Edit
Click the Base Station menu at the very top of the computer screen. Do not click the Base Station tab in the center of the screen.
Click Add Printer and then select the First Attempt method, then click Continue
The Time Capsule will search for you printer. If it finds it, click Done
If this method does not work for your pinter, you will need to follow the manufacturer's instructions for manually connecting the printer to the wireless network.

IMac + Canon pixma mp 500

Hi, I cannot get my IMac to connect to my Canon Pixma MP500. I went to the canon site and it says:
There is no driver for the OS Version you selected. The driver may be included in your OS or you may not need a driver.
And the options my Mac provides does not include the one I need. Does this mean I need to get a new printer?!!!
http://www.usa.canon.com/cusa/support/consumer/printers_multifunction/pixma_mp_s eries/pixma_mp500#DriversAndSoftware
Has anyone had luck using other driver to get your canon to print???

Hi PAHU!
Thank you so much for your recommendation. I was able to get my printer to print. Finally! Unfortunately, the scanning options are not responding.
If you know how I could also get it to scan, please let me know. For now, I'm just greatful to be printing.
Take are,
Sarita

Can a canon pixma MG6120 be used wirelessly with an ipad 3

Apologies if this is a naive question, but I'm totally new to the iPad / Apple environment & am having a hard time finding out a) if my new iPad 3 (Wi-Fi & 3G) will connect with My Canon Pixma MG6120 printer that is set up with my PC desktop computer; &, if it will - b) where can a decidedly non-techie AOP find simple step-by-step instructions to walk me through the procedure?

Below are some of the Apps which would support printing for non-Airprint support printers.
I have used ePrint, is quiet ok. But still using third party app is a pain
Air Sharing HD
ePrint
PrintCentral for iPad
Print Magic HD
PrinterShare Mobile

Can my iMac OSX 10.8.5 connect to my Canon PIXMA 452 wirelessly

Similar Messages

Maybe you are looking for