Can no longer print to ethernet printer on Airport Extreme network

I have a Mac/Windows home network with two airport extreme base stations. One is connected to my dsl modem. The other is used wirelessly to extend the network, and I have a Xerox Phaser 5500 connected to one of its lan ports. Until recently, all computers, connected wirelessly could share the internet connection and print to the Phaser. Due to a power failure, I have to reset both the Airport base stations, and now I can not print from any of the computers.
The print monitor says the network host is busy, but the IP address it gives for the printer is the same assigned to my MacBook.
Any help would be greatly appreciated.

There are some differences in sharing but it will work. I have a G4 that I use as a server, too.
First, tell me what printer model. There are driver differences, too.
At the heart, CUPS (the print control subsystem) uses IPP as the print sharing protocol. That part hasn't changed. So I recommend, for troubleshooting, setting up the printer on the client using IP printer > IPP protocol.
Here's a guide:
1) On the 10.5 print server, use a browser and point it at the CUPS admin web page athttp://localhost:631
Go to Printers list and find the queue name from the left side of the page next to the printer you want. Also note the IP address of the server Mac.
2) On a client, Add the printer as an IP printer > IPP protocol, and enter the IP address and queue name you noted above.
3) Select the generic postscript driver (on client Mac)
(after reading your second post, I want to remind you to set the server to use the correct driver.)
Finish and try it.

Similar Messages

  • Time machine can no longer see USB drive connected to airport extreme

    According to what I read, as of March, a year ago March, with update 7.3.1 Time Machine will see the USB hard drive connected to the Airport Extreme. This was working fine. It no longer does. I had the latest airport extreme software and firmware updates. I tried going back to 7.3.1.
    Does any one have any idea how to make Time Machine work again when connected to my airport extreme?

    bradleydad wrote:
    According to what I read, as of March, a year ago March, with update 7.3.1 Time Machine will see the USB hard drive connected to the Airport Extreme. This was working fine. It no longer does. I had the latest airport extreme software and firmware updates. I tried going back to 7.3.1.
    Does any one have any idea how to make Time Machine work again when connected to my airport extreme?
    what exactly do you mean when you say that TM doesn't see the drive? do you mean you can not choose it as the destination TM drive in TM system preferences? do you see the airport drive mounted in finder? if yes, connect it directly to your mac and repair the disk (not permissions) with disk utility. then move it back to AEBS. see if that helps. if not try the following terminal command
    defaults write com.apple.systempreferences TMShowUnsupportedNetworkVolumes 1
    it should not be necessary with drives connected to AEBS but it might work.

  • I can no longer connect to the internet via Airport Extreme.  HELP!

    Over the weekend my Macbook told me that my Airport extreme firmware needed to be updated, so I did that, now I have no internet connection from the Airport. I have no problem connecting to the Airport itself, but I have no actual internet connection. The connection is fine when I plug an ethernet cable directly into the computer.
    I really hope someone can help with this!

    Hi DaveX83 and welcome to the discussions.
    A few things to try.
    Press the reset button once on the back of your Extreme and let it restart. Check for proper operation.
    If no help there, keep the ethernet cable connected, and open Airport Utility. Click on Manual Setup near the bottom of the pane. On the next screen click the Airport icon at the upper left of the pane, then click Wireless in the line just below that reads Summary - Time Capsule - Wireless - Access.
    Check to see that your wireless is set up, security set up, passwords, etc. You may need to reconfigure your wireless settings again and update the Extreme to store them and restart.
    Hope this helps.

  • Printing to Ethernet Printers Using Airport Extreme Base Station 802.11n

    I don't want anything extraordinary. I think what I have to set up is pretty simple.
    I have a PowerMac G5 tower and an Airport Network with an older 802.11g AExBS connected to my cable modem. I just acquired an AExBS 802.11n. While I'm sure that people would tell me to ditch the older one an just use the newer one, that is not today's task.
    All I would like to do is to use the AExBS for my 3 Ethernet printers. The printers are:
    Brother HL-2070N
    Brother MFC-420CN
    HP Color Laserjet CP2025dn
    Each printer is plugged into each of the 3 ethernet ports and not the WAN port. I didn't have any problems using my Netgear WGT624 wireless router, so I don't know why the AExBS is giving me such a headache. Is there something simply I'm missing in the instructions? Can anybody tell me if I'm missing something here?

    Now I have managed to delete all but my directly connected USB printers in the Print & Fax area of my System Preferences. What gives?
    I thought this was going to be straight forward. They don't even address hooking up ethernet printers in the manual. I've looked over the web and see other people having the same problem, but their original setup appears to be different and/or more difficult.

  • WARNING: NEW-PAGE PRINT can no longer be used to print dialog box

    i am getting a warning as 'NEW-PAGE PRINT can no longer be used to print dialog box'. Please suggest what method can i use otherwise

    Please create a screenshot of the problem you're seeing by following the guide mentioned at [[How do I create a screenshot of my problem?]].
    Once you've done this, attach the saved screenshot file to your forum post by clicking the '''Browse...''' button below the ''Post your reply'' box. This will help us to visualize the problem.
    '''Try the Firefox Safe Mode''' to see how it works there. The Safe Mode is a troubleshooting mode, which disables most add-ons.''
    ''(If you're not using it, switch to the Default theme.)''
    * You can open the Firefox 4.0+ Safe Mode by holding the '''Shift''' key when you use the Firefox desktop or Start menu shortcut.
    * Or use the Help menu item and click on the '''Restart with Add-ons Disabled...''' menu item while Firefox is running.
    ''Don't select anything right now, just use "'Start in Safe Mode"''
    ''To exit the Firefox Safe Mode, just close Firefox and wait a few seconds before using the Firefox shortcut (without the Shift key) to open it again.''
    '''''If it is good in the Firefox Safe Mode''''', your problem is probably caused by an extension, and you need to figure out which one.
    Please follow the [[Troubleshooting extensions and themes]] article for that.
    ''When you figure out what's causing your issues, please let us know. It might help other users who have the same problem.''

  • Can I print from my iPad using airport extreme?

    Can I print from my iPad using airport extreme 802.11n ?

    iOS devices use AirPrint to print directly to a printer. That would require a printer that is AirPrint-ready. Unfortunately, just connecting a non-AirPrint-ready printer to the USB or Ethernet ports of the AirPort Extreme Base Station (AEBS), will NOT enable it for AirPrint.

  • Can multiple Airport Expresses be connected via ethernet to an Airport Extreme to extend a single WiFi Network?

    I am a big fan of both the Airport Extreme and Airport Express.  In my work environment, I need to create a good quality single wireless network around 2 large aircraft hangars and some offices at the perimeters.  We have a good quality wired Cat5e ethernet network extended between the buildings and offices now.  Is this possible and does it seem like a good practical solution?  I think that 4 or 5 Airport expresses would easily provide good wireless coverage in the needed areas. 

    Can multiple AirPort Expresses be connected via ethernet to an AirPort Extreme to extend a single WiFi Network?
    Yes, this will work just fine as long as any individual Ethernet cable run will not exceed much over 330 feet or about 100 meters.

  • Setting up PC to print on Airport Extreme Network

    I just purchased an iMac and Airport Extreme. I've set up my printer on the Airport Extreme Network and can print from the iMac. While I've got the PC on the network, I'm having troubles setting up the printer. When I try to "Add a Printer" I'm not sure how to find the network and correctly setup the printer. This has to be any easy thing to do... Any suggestions?

    Hello Jklink. Welcome to the Apple Discussions!
    If not already, be sure to install Bonjour for Windows to facilitate printing to an AirPort base station.
    (ref: Printing to an AirPort Extreme Base Station from Windows XP & Printing to a printer on a Mac running 10.4.x from a Windows PC using Bonjour for Windows)

  • I'm trying to setup a printer go wireless through my airport extreme, but every time I try to print the printing file gets paused. I'm in loop. PLEASE HELP! (The printer is a Brother 7020  monochrome)

    I'm trying to setup a printer go wireless through my airport extreme, but every time I try to print the printing file gets paused. I'm in loop. PLEASE HELP! (The printer is a Brother 7020  monochrome)

    I had the exact same problem
    It turns out I was using a 20 foot USB cable between the printer and the Airport Extreme and the signal had become to weak to work. Try using nothing more than a 6 foot cable or try a new cable

  • 17" flat panel Mac can no longer get on my Airport Extreme network

    My 17" G4 flat panel iMac can't get on my Airport Extreme network. It has been on the network for years. All of a sudden I can't get on my own network. The Airport extreme uses a WAP2 Security password. Everything else in my home is on this network ie. Blu-Ray players, Wii, Nintendo DS's, MacBook, Apple TV. The G4 doesn't even have WAP2 as an option! Where did the option go? I really don't wanna set up the network again with a WEP password(That's an option on the G4) and have to reset everything. What happened?

    There were two 17" flat-panel G4 iMacs. The earlier of the two (Part# M8812LL/A) had an optional AirPort Card. This card only supports 802.11b and either the WEP or WPA security standards. It does not WPA2. This may be the reason the G4 is not able to connect to your wireless network if you have it configured for WPA2 Personal.
    You will need to reconfigure the AirPort to use the "WPA/WPA2 Personal" option.

  • How can I add an additional ethernet connection to my existing network?

    Greetings:
    What follows is a question from a newbie, so please forgive my ignorance:-)
    I have been trying to connect Logitech's google tv unit to my existing Airport Extreme network via an ethernet Cat-5e cable. The Logitech unit's ethernet port is blinking, but the AP Extreme's LAN port does not. I'm sure I have to re-configure my Extreme and have searched, but have not found anything that has worked. I'm sure this is a simple matter, but like I said...newbie:-)
    My setup is as follows:
    Time Warner Cable modem–to–AP Extreme via WAN–to–Apple IMAC via ethernet.(This set-up works fine to provide internet to my computer as well three other wireless devices) The set-up to the Logitech is: AP Extreme via LAN ethernet port–to–Logitech ethernet port with a CAT-5e ethernet cable.
    Any help would be most welcome and greatly appreciated.
    Thank you in advance.

    Hello bardlight. Welcome to the Apple Discussions!
    Based on your configuration description, the Logitech TV is physically connected properly to the 802.11n AirPort Extreme Base Station (AEBSn). You do want it connected to one of the available LAN ports on the AEBSn.
    By default, the AEBSn, is performing as a DHCP server. Also, by default, most computing devices are configured as DHCP clients. What this means is that the AEBSn should be providing the proper IP addresses to any connected (wired or wireless) in order for that device to access both the network and on to the Internet.
    It sounds like that Logitech TV is just not configured properly as a DHCP client.

  • How can i access my hdd hooked to my airport extreme base station at home, from another place,office,school..?

    i have an airport extreme base station ,i conneted a hdd and i want to acces the hdd with my macbook from another place ...office...school....

    I would appreciate if someone could tell me how the AirPort Extreme differs from any regular router.
    The AirPort Extreme is a combination router, wireless access point, and Ethernet switch. It also provides both external USB hard drive and printer sharing. So, it is not much different than most other routers on the market today. The one main difference is how you administer it. Unlike most other routers that employ a web-based administration interface, the AirPorts use a dedicated utility, called the AirPort Utility.
    I do not have any OS X devices, but I have a lot of iOS devices.  If my understanding is correct, I can set up the AirPort from an iOS device.
    Yes. There are versions of the AirPort Utility for OS X, Windows, or iOS devices.
    Also, I need to know how I would connect my Synology NAS system to the AirPort Extreme network via an Ethernet cable.  I would need to be able to acces the files on the NAS through Windows clients.  My Synology NAS currently has a web interface....would I still be able to access that web interface with the AirPort?
    Your Synology NAS would connect to the AirPort Extreme pretty much the same as for any other manufacturer's routers. That is, you would connect it to one of the available LAN (opposing arrows) ports on the Extreme. You would still use the same web-based interface as before.
    Note: When connected to an Ethernet port, the NAS would still function as usual. The AirPort Extreme would not provide any file sharing functionality when connected in this manner. All file sharing features would be the responsibility of the NAS device.

  • Where can I find the MAC Address of a Airport Extreme ?

    Where can I find the MAC Address of a Airport Extreme ?
    I need this to extend the wi fi range in my home. I'm using a Motorola Cable modem and to extend with Airport Extreme, I need to set up inside Motorola the MAC Address of the Airport Extreme.
    Message was edited by: JPA3003

    There are actually 3 MAC Addresses on an AirPort Extreme......1 for Ethernet, 1 for 2.4 GHz wireless and 1 for 5 GHz wireless.
    You can normally see them by using AirPort Utility. The rub here is that the AirPort needs to be setup and working to be accessed by AirPort Utility.
    The other approach is to look on the bottom of the AirPort. The newer AirPorts usually have this information in very small print, so a magnifying glass will probably be required. Other versions embed the numbers in the foam mat.
    Note.....Apple uses proprietary settings for the their wireless "extend" feature.....designed to only allow other Apple devices to connect. So, it is extremely unlikely that the AirPort would be compatible with a 3rd party router if you are trying to use the AirPort to wirelessly extend the network.
    Let us know if you are able to do this.

  • Can I use non-apple notebook to connect AirPort Extreme?

    I
    Can I use non-apple notebook to connect AirPort Extreme?

    He might be trying to do so to promote his products or may be there was some misunderstanding.
    Airport Extreme will work as a wireless router supporting upto 50 systems including Mac computers, PCs, iPad, iPhone, iPod touch, Apple TV and virtually all 802.11a/b/g/n Wi-Fi wireless devices — all at the same time.
    for reference http://store.apple.com/us/product/MD031LL/A/AirPort-Extreme

  • I can see my airport extreme network, but none of my devices (vista, ipad, iphone, ipod) can connect to it. Why?

    I have set up my apple aiport extreme after moving and I can see the airport extreme light is green and I can see the airport extreme network name, but when I select the network, the device cannot connect to it. No error message appears, the device simply is in a constant state of trying to connect to the network.
    I can easily connect to the non Airport Extreme network.
    Can anyone help?

    Try factory resetting, it often helps when changing location.

  • I changed my Airport Extreme network name and password, now I can't access my Airport Express speakers.  Help please.

    I changed the network name and password associated with my Airport Extreme and now my system is not recognizing my Airport Express speakers.
    Can someone help me get my speakers and sound system back online?
    Thanks in advance for any assistance.

    You will need to think in reverse here.
    Change the network name and password back to where it was on the AirPort Extreme and get things working that way.
    Then, change the name and password on one AirPort Express, then the second. Both Expresses will be blinking amber at this time. Power them off.
    Now, change the name and password on the AirPort Extreme.
    Power up both Expresses and they will now join the AirPort Extreme network correctly since you have programmed them with the new network name and password.

Maybe you are looking for