Can not access FWSM via session command in cisco 6513 (VSS enabled)

Dear All,
              Today i received FWSM from cisco (RMA), I need to configure it as standby unit for existing FWSM active/standby setup.
IOS on RMAed FWSM is 2.3.4 and cisco VSS supports FWSM IOS 4.0.4 and later.
My issue is, I cannot access FWSM (IOS 2.3.4) via session command from cisco 6513 but could successfully consoled it without any problem. I have reloaded it twice and also tried to disable and enable power on it.
VSS#sh module switch 2
Switch Number:     2   Role: Virtual Switch Standby
Mod Ports Card Type                              Model              Serial No.
   2    6 Firewall Module                        WS-SVC-FWM-1 -----------
Mod MAC addresses                       Hw    Fw           Sw           Status
2 0034.2fd7.3b04 to 0019.2fa7.3b0b   4.2   7.2(1)       2.3(4)       Ok
Mod Online Diag Status
2 Pass
VSS#session switch 2 slot 2 pro 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
Trying 127.0.1.21 ...
% Connection timed out; remote host not responding
Can someone please let me know why I cannot access FWSM through session command ?
Whether this is because of older IOS ? If yes then how to upgrade its IOS ?
Is it possible to upgrade IOS via FWSM console ? if yes, please let me know.
Do i need to test on different slot ?
Look forward to hearing from someone.
Thanks & Regards
Ahmed...

There is a limitation that FWSM running version older than 4.0.4 will not accept session from the switch if the FWSM is not seated into switch 1 AND if switch 1 is not active.
So to upgrade the FWSM you either need to use the console or put the FWSM physically in switch 1.
Thanks,
Jeroen

Similar Messages

Can not access internet via wired connection, wireless working OK

Background information,Came home from vacation turned on PC to access email.Emails started downloading then stoped,started getting messages that firefox stopped working and Thunderbird quit working and others.My desktop is attached to a verizon router.all my other devices are wireless and are working fine through the same router.I connected my laptop to the lan connection, turned off wifi and accessed the internet via lan connection.Using device manager, checked drivers, says up to date, also says that it is working properly.I have gone to the command line and can ping google.com.I can ping the loop around. ping127.0.0.1I have done the ipconfig/release,ipconfig/renew, and ipconfig/flushdnsipconfig/all indcates that it is there and enabledMy Lan connection is part of the mother board.can not access internet via wiredconnection.Not sure what to do next.Help Please

Reply: I spent about an hour last night doing all the things that you suggested including moving the lan cable from my desktop to my laptop which worked fine. When I hoover over the connection it says; Network3 Internet Access no error messages.When I unplug the cable at the router a red x covers that connection icon.Plug it back in red x goes away.It is seeing the router, just does not appear to be providing selected web page info.Computer thinks it is working fine.

Security photo - does not show any apps that have requested access. I can not access photos via apps. How to fix it?

Apps can not access photos.
Apps never asked if they could access photos.
Security>Photos - there are no apps on the list.
I have restarted.
Backed up, restored.
No improvement.
Thanks.
ps my iphone allows access, so I know 'how' to do it usually.

Found the answer:
Go to settings/general/restrictions/photos and allow the apps to have access to photos

Can not access DTR via NetWeaver Developer Studio

Hi all,
I'm able to access DTR in the browser with this URL : http://<servername>:50000/dtr
That's good.
Now ... I specified the same DTR server URL when creating a new DTR client in NWDS.
When I tried to log on it says :
Ping on server http://<servername>:50000/dtr/ returned: 401 Unauthorized
User not authorized for server http://<servername>:50000/dtr/
Howcome I can login via the browser but not via NetWeaver Developer Studio ?
Can anyone help me with this issue plz ?
Kind regards,
Abjuh

Hi Slava,
Thx for your answer.
Indeed my user & paswords where different on some systems.
Now I made sure that all usernames & paswords are the same on every system.
Issue solved !
Thx & regards,
Abjuh.

Can not access DVR or program DVR to record via web or apps

I can not access my DVR remotely via a PC or via the apps. I get a message that says cannot connect to your DVR right now, try again later. It has been like this for weeks. I called tech and they reset all the boxes, the ONT, I removed the COAX etc. rebooted and cleared router. The box can be seen online though just not the DVR. Also, on screen caller id does not work and the fix application does not fix it either.

It seems like I lose web access to the DVR every week.
I either have to unplug the DVR or have Verizon send a reboot signal. Even that doesn't work every time. It is a really annoying and inconvenient problem.

Can not access home network via ipod touch, password entered not accepted

Can not access home network via ipod touch, password entered not accepted
Trying to help my son set up his ipod touch to connect to the network and the password I entered is not accepted.
1. Which password is required? I entered the password I use for logging into my router
2. The home network is recognized, when selected it requires a password to be entered, but I am just not sure what password it is looking for to connect.
I have not been able to find any information on this subject

jersey0904, Welcome to the discussion area!
You need to enter the wireless encryption password... not the administrative password for the router.

HT4906 I have upgraded my OS to Mountain Lion and updated Iphoto to latest, however, I still can not access photos sent to me via photo stream. what else do I need to do? I'm $30 into this effort, and no results!

I have upgraded my OS to Mountain Lion and updated Iphoto to latest, however, I still can not access photos sent to me via photo stream. what else do I need to do? I'm $30 into this effort, and no results!

Log out of iCloud in the System/iCloud preference pane and disable Photo Stream in iPhoto's Photo Share preference pane. Then log back in and re-enable, respectively. That should jump start Photo Stream.
OT

Can not Access disk drive attached to WRT350N via an FTP client

Background
I have a WRT350N v1 running the most current firmware. I have a static IP address for the WRT350N and I can ping it over the internet. I have a disk drive attached to the 350N with a FAT32 partition that has been set up for shared access for a selected group and user. I have worked with cicso/linksys support to verify the linksys350N is set up correctly (?).
Problem
I can not access the disk drive attached to the WRT350N via an FTP client. I have tried the following FTP Clients: Transmit and Filezilla. I get a "Connection established, waiting for welcome message...' message on the FTP client. Then it says Connect timeout, Can not connect to server. I CAN connect to other FTP sites so its not the FTP client software.
What I have done so far
1. deleted the old and added a new FTP group and user
2. unplugged and reconnected my WRT350N and my cable modem
3. Contacted Cisco/linksys support on-line and they verified my setup and can ping my 350N but thats as far as they are willing to help
I haven' a clue as to what to do next. Any and all help is greatly appreciated.

Access your router set-up and make sure you have :
1. Enabled FTP Server and Internet Access under the FTP Server subtab under Storage...
2. Reduced the MTU size to 1300 under SetUp...
3. Unchecked Filter Anonymous Internet Requests...
If you have done all this and nothing works, then, you need to upgrade your router's firmware and re-configure your router and then enter the settings...
Download Firmware 3.23 MB...
Follow these steps to upgrade the firmware on the device : -
Open an Internet Explorer browser page on a computer hard wired to the router...
In the address bar type - 192.168.1.1...Leave the username blank & in password use admin in lower case...
Click on the 'Administration' tab- Then click on the 'Firmware Upgrade' sub tab- Here click on 'Browse' and browse the .bin firmware file and click on "Upgrade"...
Wait for few seconds until it shows that "Upgrade is successful" After the firmware upgrade, click on "Reboot" and you will be returned back to the same page OR it will say "Page cannot be displayed".
Now reset your router :
Press and hold the reset button for 30 seconds...Release the reset button...Unplug the power cable from your router, wait for 30 seconds and re-connect the power cable...Now re-configure your router...
1. Enable FTP Server and Internet Access under the FTP Server subtab under Storage...
2. Reduce the MTU size to 1300 under SetUp...3. Uncheck Filter Anonymous Internet Requests...See if this works for you...

Unable to connect to wism2 module via session command

Hi There,
I installed two wism2 modules in our cat6509.
After basic configuration the modules comes up and I can connect via ssh/https to the controller.
For first configuration of the wism modules, I opened a session directly from the cat6509.
Now after 24 hours, there is no way to make a connection via session command from cat6509.
cat6509#session slot 9 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
Trying 192.168.12.100 ...
% Connection refused by remote host
cat6509#session slot 2 processor 1
The default escape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
Trying 192.168.12.101 ...
% Connection timed out; remote host not responding
Has anybody an idea why I can not open a session to wism2 module?
Thanks
Bjoern

You can load the software via the command line interface. Configuration via WebUI is not available at this point since the Management Interface on the wireless controller is not configured yet. The controller should be configured to operate properly on your network and configured with the IP addresses of your working subnets. You can configure the wireless controller by directly attaching it to the console ports on the WiSM2 controller or opening a console session to the controller module from the Catalyst interface as shown here.
Note: You can access the WiSM2 through a session command directly now.
CAT6504-MA#session slot 3 processor 1
The default excape character is Ctrl-^, then x.
You can also type 'exit' at the remote prompt to end the session
Trying 192.168.2.21 ... Open
(WiSM-slot3-1)
User: admin
Password:*******
(WiSM-slot3-1) >

Can not access the media card files Blackberry 8310 - HELP

Can not access the media card files Blackberry 8310.
I had a battery drain problem. The unit would only last 16 hours before completely drained. Purchased a new battery with the same result. I figured that I should try a complete reset so I did a hard wipe. Once that was done and I loaded the unit back up and returned online, the battery drain problem was resolved but now I can not access the media card.
Here are the messages:
“A media card has been inserted that contains encrypted content which will be unaccessible by this device”
I can see the files. I have transferred them to my PC via the SD card but I can not open them. Here are the settings:
Media card support – ON
Encryption Mode: - Security Password & Device
Encrypt Media Files – YES
Mass Storage Mode Support – OFF
Please note – I can not change the encryption mode since it is set by policy
Security Options – General Settings – Content Protection – Disabled
The version of Desktop Manage I am using is 4.2.1.8. When I try to use the Media Manager to move the files, I get an error message and can’t move the file. If I access the file on the card and try to display it, I get:
Unable to display file /media card/ pictures/ing000000xx.jpg.rem
Here is what I have tried (from the advice on this board):
1)     Read the files directly off the media card – No good
2)     Create a “new” folder on the media card and move a file into it then try to read it – No good
3)     Email the file then read it – No good
4)     Reset Encryption mode to off then try – Can’t do it – IT Policy setting
5)     Be sure that the password was set the same as before the wipe (setting is password & device) – Can’t do it – The Blackberry prevents me from using an old password.
So I think I can’t read the files because I can’t replicate the encryption key. Could that be right? My problem is that I do not understand why this would be the case. It is still the same device and since it knows what the old password was (because it would prevent me from using it again), why would it not generate a key to access the files?
All I am trying to get off the card are pictures on my 6 year old … some are priceless. Can someone help me do this? One would think that this should not be this hard but from all the postings I have found, it seems that it is. And yes, shame on me for not moving the files before I did the reset (THAT will never happen again!) but this being unrecoverable is unconscionable given how many seem to find themselves in this situation.
Thanks for any help you can offer!

Not sure why you couldn't see them using mass storage mode. Did you have the pics stored on your media card? Try going to media-menu-explore-media card-blackberry-pictures See what the extension is on your pics. If any have the extension such as .jpg.rem they are encrypted.
IrwinII
Please remember to "Accept as Solution" the post which solved your thread. If I or someone else have helped you, please tell us you "Like" what we had to say at the bottom right of the post.

After install Crystal Report Server 2011, can not access control tools

Afte install Crystal Report Server 2011, can not access control tools from web or from application.
My server OS is Windows 2008 R2 SP1. I follow the default setting. How to fix it?
Error message is above.

Is Tomcat started? On your Start menu you should have an option to get to "Tomcat Configuration" or, under the CRS menu you can run the "Central Configuration Manager" to start Tomcat.
What URL are you using to connect to the web app? By default Tomcat runs on port 8080 so your URL should look something like this: "http://<servername>:8080/BOE/CMC" or "http://<servername>:8080/BOE/BI".
If Tomcat is running and you're trying to access it from another computer, check to see if the Windows Firewall is turned on for the server - if it is, turn it off for "Domain" access.
If Tomcat won't start, go to the folder where Tomcat is installed and then look in the "logs" folder. There should be a file called "stderr.log" which you can open in Notepad to see what types of errors might be occurring (you can ignore any errors having to do with "persisted sessions".) If there are other errors, post in the BI Platform space to get assistance.
-Dell

I accidentally deleted some drivers from my macbook air and now i can not access app store and system preferences as it says the following message (You can't open the application System Preferences because it may be damaged or incomplete)

i accidentally deleted some drivers from my macbook air and now i can not access app store and system preferences as it says the following message (You can't open the application System Preferences because it may be damaged or incomplete)

Repair the Hard Drive and Permissions - Lion/Mountain Lion
Boot to the Recovery HD:
Restart the computer and after the chime press and hold down the COMMAND and R keys until the menu screen appears. Alternatively, restart the computer and after the chime press and hold down the OPTION key until the boot manager screen appears. Select the Recovery HD and click on the downward pointing arrow button.
Repair
When the recovery menu appears select Disk Utility. After DU loads select your hard drive entry (mfgr.'s ID and drive size) from the the left side list. In the DU status area you will see an entry for the S.M.A.R.T. status of the hard drive. If it does not say "Verified" then the hard drive is failing or failed. (SMART status is not reported on external Firewire or USB drives.) If the drive is "Verified" then select your OS X volume from the list on the left (sub-entry below the drive entry,) click on the First Aid tab, then click on the Repair Disk button. If DU reports any errors that have been fixed, then re-run Repair Disk until no errors are reported. If no errors are reported then click on the Repair Permissions button. When the process is completed, then quit DU and return to the main menu. Select Restart from the Apple menu.

TS3798 I get this error message"your operation could not be completed" I need help figuring out why I can not access the web page.

I get this error message"your operation could not be completed" I need help figuring out why I can not access the web page.

amarilysfl wrote:
"Your disk could not be partitioned. An error occurred while partitioning the disk".
https://www.apple.com/support/bootcamp/
If you were using Apple's BootCamp and received this message, quit it and open Disk Uility in your Applicaitons/Utilities folder.
Select the Macintosh HD partition on the left and select Erase and Erase Free Space > Zero option and let it complete (important) this will check the spare space for bad sectors that can cause issues formatting partitions.
Once it's completed, try creating a partiton again in BootCamp.
If that doesn't work, then hold command option r keys down while connected to a fast internet connection, Internet Recovery should load (spinning globe) and then in that Disk Utility, select your entire internal drive and click > First Aid > Repair Disk and Permissions.
reboot and attempt Bootcamp again.
If you still get a error, it might be that you have OS X data on the bottom area where BootCamp partition needs to go. This would occur if you had the drive or computer for a long time or wrote a large amount of files to the drive and nearly filling it up and then reduced some, but it left traces in the area BootCamp needs to go.
To fix this
BootCamp: "This disc can not be partitioned/impossible to move files."
How to safely defrag a Mac's hard drive

Can Not Access Apps?

I can not access the App store? I have tried everything even update and all I get is a grey Apps screen?

Launch the Console application in any of the following ways:
☞ Enter the first few letters of its name into a Spotlight search. Select it in the results (it should be at the top.)
☞ In the Finder, select Go ▹ Utilities from the menu bar, or press the key combination shift-command-U. The application is in the folder that opens.
☞ Open LaunchPad. Click Utilities, then Console in the icon grid.
Make sure the title of the Console window is All Messages. If it isn't, select All Messages from the SYSTEM LOG QUERIES menu on the left. If you don't see that menu, select
View ▹ Show Log List
from the menu bar.
Click the Clear Display icon in the toolbar. Then try the action that you're having trouble with again. Select any messages that appear in the Console window. Copy them to the Clipboard by pressing the key combination command-C. Paste into a reply to this message (command-V).
When posting a log extract, be selective. In most cases, a few dozen lines are more than enough.
Please do not indiscriminately dump thousands of lines from the log into this discussion.
Important: Some private information, such as your name, may appear in the log. Anonymize before posting.

Can not access a website but everyone else is doing well and the old computer with the same internet coming in on that side.

Can not access a website but everyone else is doing well and the old computer with the same internet coming in on that side. side is www.miun.se

You can remove all data stored in Firefox from a specific domain via "Forget About This Site" in the right-click context menu of an history entry ("History > Show All History" or "View > Sidebar > History") or via the about:permissions page.
Using "Forget About This Site" will remove all data stored in Firefox from that domain like bookmarks, cookies, passwords, cache, history, and exceptions, so be cautious and if you have a password or other data from that domain that you do not want to lose then make a note of those passwords and bookmarks.
You can't recover from this 'forget' unless you have a backup of the involved files.
It doesn't have any lasting effect, so if you revisit such a 'forgotten' website then data from that website will be saved once again.

Can not access FWSM via session command in cisco 6513 (VSS enabled)

Similar Messages

Maybe you are looking for