Can not connect to airport time capsule

Here is what the current situation is:
I can setup the Airport Time Capsule (3GB) form my Mavericks 10.9.4 MacBookAir 2013 using AirPort Utility. However, after setup, I cannot connect to the time capsule using many of the standard ways. Trying both connections of wired and wireless. I have tried:
1. Connecting to the Time Capsule using Time Machine (which I can see the Time Capsule Drive as a selection), and I always get the error "There was a problem connecting to the server “XXXXXX”. Check the server name or IP address, and then try again. If you continue to have problems, contact your system administrator."
2. Using Finder side bar under Shared (which I can see the Time Capsule Drive as a selection), clicking on it, always says Connection Failed at the top of the window. Clicking the Connect As... button results in the same error message as #1.
3. Using Finder, connect to server option, entering the name of the time capsule with .local at the end, and using the ip address and it always returns the same error as #1.
Trying option #3 and looking at the Console for error messages always produces these two messages:
Date Time NetAuthSysAgent[1093]: ERROR: AFP_CreateSessionRef - AFPLoadModules failed 22
Date Time NetAuthSysAgent[1154]: NewAFPLoadModules: bootstrap_look_up failed Unknown service name
Any help would be much appreciated. My computer has security scripts run on it that my company wrote inhouse and not sure exactly what is locked down and not locked down. Thank you.

Using method 3.. try
SMB://TCname.local or SMB://TCIPaddress (I hope obvious you replace with actual name or actual IP).. Please use names that are SMB compatible.. ie short, no spaces and pure alphanumeric.
No luck try CIFS:// etc.
This forces it to SMB1.
No luck ping the TC in terminal.. does it respond??
Do you have ipv6 set ot link-local only in the computer??
Your company may have locked you out.. I would not be surprised. Are you running a vpn on the computer whilst trying to connect to the local network. That will fail and the ping test will show you why.
Date Time NetAuthSysAgent[1093]: ERROR: AFP_CreateSessionRef - AFPLoadModules failed 22
Date Time NetAuthSysAgent[1154]: NewAFPLoadModules: bootstrap_look_up failed Unknown service name
Interesting.. it is blocking AFP perhaps. AFP modules refused.. I do not know the errors well enough but if AFP fails there is a good chance TM won't work. So even if you can mount and access the disk I am not sure you can do TM backups.

Similar Messages

  • I purchased a new router and now I can not connect to my time capsule. What should I do?

    In the past, I have just used my time capsule to back up my macbook pro. It connected wirelessly and everything worked great. I recently purchased a new router and now I cannot connect to the time capsule. Please help!

    Is that other router the "main" one?  If so, you'll have to configure the Time Capsule to "join" the network created by that router.  The details of how to do that and whether it's possible may depend on the brand and model of that router, but I have no details on that.

  • I can not connect to my Time Capsule, rescaning for the device does not work.

    I used extra Len Cable to connect to my MacBook but still it can not find the Time Capsule.
    What are my other options to try reconect the Time Capsule again?

    Hard reset did the trick.
    I was able to finally see my Time Capsule after few minutes.

  • I can not start up airport time capsule.

    The problems seems to be internet connection. my modem is working properly, ethernet cable is connected from the modem to the WAP ethernet at the airport TC. I reset both systems to check compatibility nothing happens.

    Ok.. wifi is working so the basic TC is operating.
    What is the modem? If it is a cable modem did you power cycle it for at least 30min off.
    You cannot simply change devices on a cable modem.. the Cable system registers the first client and assigns it the public IP address. You MUST force the cable ISP to release this address so it can be assigned to the TC.
    Sometimes 15min is enough.. sometimes overnight is needed. Who is your ISP?
    Sometimes you will need to call your ISP and get them to reset the modem port.
    Some cable modems are a real pain.. eg SB6121 or 6141. That is why the model of the modem is important.
    Keep telling us more info..
    A screenshot of the TC settings for internet can also help.

  • How can i use the airport time capsule as a external hard drive?

    how can i use the airport time capsule as a external hard drive?

    Why do you recommend not place things like iTunes libraries or photo libraries on the drive? It was what I am looking for...
    I suggest that you ask the experts over in the iPhoto Support Community about their opinions on placing an iPhoto or Aperture library on the Time Capsule....even if you plan to use a wired connection for your Mac and the Time Capsule.
    But, if Terrence Devlin answers, be prepared for a lecture about why you should not ever do this.
    If you place the iTunes library on the Time Capsule, be prepared for iTunes to give you messages about not being able to find the library.
    In addtion, LaPastenague has the answer for you in a nutshell......corruption problems.
    Bottom line....the Time Capsule is for your backups.....not "everyday" files and especially not libraries.

  • I can't connect with the Time Capsule.

    Hello everyone,
    Some years ago, I bought a Time Capsule. Until now, I didn't want to use it as an extern HD.
    So I tried today.
    I am using it for a year now, as main router. Several computers and iDevices are using it.
    Because I had forgotten some things - and I hadn't wrote it down - I decided  to reset it and configure it again.
    Since then, the internet has become slower - and I my Macbook pro can't connect to the Time Capsule's disk.
    In Finder's everything fine. Left, under 'Shared', I can see the Time Capsule as a HD.
    When I click on it, I see: "No Connection". Then I select "Connect As", and I fill in the Time Capsule password.
    It tries to connect a few minutes, but then I get the message:
    "The backup disk could not be found. Make sure the backup disk is connected or open Time Machine preferences to select a different backup disk."
    In the Airport Utility, there's a green light.
    *My firmware has the newest updates
    *I am using Snow Leopard
    *I am using newest update of the Airport Utility
    *Since reset, internet's fine but a bit slower.
    Other Questions:
    *Can I use my Time Capsule for other things than only Time Machine (backup)?
    *Can I divide it in parts? (Backup, User)
    *Can I backup multiple devices on it? (Macbook Pro, iMac, Macbook Air etc.)
    Hope you can help me!
    iFallrise

    What actual model is the TC.. the A1xxx number from the rubber base mat???
    As they age they become unreliable. Some earlier and some at 3year mark.
    It greatly depends on the setup of the existing network.
    I would recommend a downgrade in the TC firmware.. as with Snow Leopard there is no advantage to you in the later firmware.
    Go to the airport utility and select firmware update.. hold down the option key when you make the selection and all the previous versions available for your model will come up. I recommend using 7.5.2
    Do another reset of the device. This time a full factory reset.. and start the configuration again.
    Ignore update to firmware requests.. turn off the reminder.
    Set all names to SMB standard. short, no spaces, pure alphanumeric. TC name, wireless names, hard disk name.
    For wireless I recommend you use wpa2 security with 8-12 character passkey.. pure alphanumeric.
    Set to manual for radio channels and test 1, 6, 11 in turn for the best.
    Depending on the broadband you use, the TC must be in router or bridge mode.. tell us more if you need help for this.
    If you think the TC is slowing you down, do a test with direct connection to the broadband modem and give us the speed comparison.. direct and via the TC ethernet or wireless.. tell us which though.. wireless will always be slower than ethernet.
    If you have issues still with the hard disk it might need some work.. older models the disk might need to be erased .. please open any time machine backup and run a verify.
    A5
    http://pondini.org/TM/Troubleshooting.html
    Other Questions:
    *Can I use my Time Capsule for other things than only Time Machine (backup)?
    Yes, but the TC is designed primarily for Time Machine.. if you store files, there is no method in the TC to back up those files.. do not make them the only store.
    *Can I divide it in parts? (Backup, User)
    You cannot partition a TC .. not without removing the disk. You can create a disk image.
    Q3 http://pondini.org/TM/Time_Capsule.html
    *Can I backup multiple devices on it? (Macbook Pro, iMac, Macbook Air etc.)
    You can use multiple devices with TM. Be aware you need lots of free space for this to be successful. So you need to add up the total you want to backup on each computer.. and at least double it.

  • External hard drive is not working on airport time capsule even after 7.7.2 firmware update.

    External hard drive is not working on airport time capsule even after 7.7.2 firmware update.
    I have the latest Airpor Time capsule 2gb. I specifically bought it so that I could have an external hardrive set up to wirelessly house my itunes library and movies. When i connect the drive, all i get is that the disk needs to be repaired.
    the drive can works fine when connected to the macbook pro and I have run the verify and repair features in disk utility. I have also reset the airport timecapsule as well following these changes and still no change.
    The 7.7.2 update says that it addressed the usb issue of not showing the drives but there are still problems as I cannot get it to appear.
    Please help.
    Thanks

    How is the hard drive formatted?
    Have you tried using a powered USB hub with the drive when it is connected to the Time Capsule?
    (The USB port on the Time Capsule is borderline as far as power is concerned....you may need to use a powered hub.....even if the hard drive has its own power supply)
    If the drive is formatted correctly....and....it has ample power, it will "show up" when you open AirPort Utility, click Edit, then click the Disks tab at the top of the next window.
    In the example below, my Time Capsule drive is named "Backups" and another drive named "WD Drive" is connected to the USB port on the Time Capsule.
    You should see the name of your Time Capsule drive (named "Data" unless you have changed the name) and the name of the USB drive if you perform the same check.
    What do you see?

  • Hello. My mac can't connect to my time capsule. There is no response and I can't put it back to the originals definitions because all my files are there and I can´t loose them. (sorry about my bad english, but I really need help!)

    Hello. My mac can't connect to my time capsule. There is no response and I can't put it back to the originals definitions because all my files are there and I can´t loose them. (sorry about my bad english, but I really need help!)

    Your files are unaffected by a reset.. no reset via the reset button on the TC harms, deletes or does anything to your files.
    The Factory Reset universal
    Unplug your TC/AE. Hold in reset. and power the TC/AE back on..  all without releasing reset and keep holding in for about 10sec. The time is not important.. it is the front LED rapid flashing that indicates you are in factory mode.
    Release reset.
    If it doesn’t flash rapidly you have released reset at some point and try again.
    Be Gentle! Feel the switch click on. It has a positive feel..  add no more pressure after that.
    TC/AE will reboot after a couple of minutes with default factory settings and will wipe out previous configurations.
    No files are deleted on the hard disk.. No reset of the TC deletes files.. to do that you use erase from the airport utility.
    Here is how to do a fully manual setup for TC which is sometimes necessary with Mavericks in particular.
    Airport Utility shows "unexpected error - please try again" when connecting to Time Capsule

  • Upgraded MobileMe to iCloud and now can't connect to my Time Capsule at home with Back to My Mac

    I upgraded my MobileMe account to iCloud yesterday and now I can't connect to my Time Capsule when I am away from my home network.  I had been able to using Back to My Mac with my MobileMe account.  Now the airport utility still only shows a mobileme option in the advanced settings.  Is there an update for the time capsule so that I can input my iCloud information?

    Apparently this isn't possible. This was never discussed publicly before the iCloud launch. All that was said was Back to my Mac would continue working. I looked everywhere and couldn't find anything, even after the iCloud launch. Made the switch, my AirPort started yelling at me because of MobileMe credentials. I've been waiting for an AirPort update but have still been digging. Just found this:
    http://support.apple.com/kb/HT4867
    Talk about a footnote. This should have its own article, not be like, "Oh everything will still work great! ... ... ...
    Except for AirPort disk sharing."
    I'm not too happy about this.

  • HT201250 What if Time Machine can't find my airport time capsule?

    I can't find my airport time capsule on my computer... I need help in order to reach documents saved on my airport time capsule used as an external hard drive... Please help!

    Is it listed in the sidebar of a Finder window, under SHARED?

  • My iPad 2 will not connect to my Time Capsule

    My iPad 2 will not connect to my Time Capsule. Both my Macbook and iPhone4 are connected. It finds the Wifi network, but will not log on. Any idea why?

    this worked fine up until last night, then all of a sudden its kicking just my iphone off the network. i am going to try to connect to other wifi's to see if i should do one of the following
    back up > full restore
    bring the phone back something went wrong with my phone

  • My iPad and iPhone are not seeing my airport time capsule

    MY iPad and iPhone are not seeing my airport time capsule.

    You cannot back up directly to a Time Capsule from an iPhone.
    iOS backups are done using either iCloud or iTunes as documented here:
    iOS: Back up and restore your iOS device with iCloud or iTunes

  • Can I connect and use Time Capsule with two printers?

    Can I connect and use Time Capsule with two printers?

    Sure, if the printers connect using the Ethernet port, you have 3 ports on the Time Capsule.
    If the printers connect using wireless only, the Time Capsule will support up to 50 connections.
    If your printers connect using USB, then you will need a powered USB hub. Something like this, for example:
    Dynex 4Port USB 2.0 Hub DX-THUB16 - Best Buy

  • I can't get my airport time capsule to connect to the internet

    I can't get my new airport time capsule to connect to the internet. It works fine with my linksys router

    We cannot help with that amount of info..
    What internet type and modem do you have? Exact modem make and model may help.
    Is the linksys router also the modem? You do know there is no modem in the TC?
    How is the Linksys authenticating if it is plugged into the modem??
    If cable did you shut down the cable modem for at least 20min to change the router.. this is always required with cable system.. often the time is longer.. one hour or overnight even.

  • Can I use the Airport Time Capsule Wirelessly without being connected to my router/mac by ethernet?

    Hey
    I've recently bought a 3TB Airport Time Capsule, with the sole intention of being able to perform wireless backups.
    Is it possible to perform these wireless backups without being connected by ethernet to my modem/existing router?  I don't want to use the time capsule as a replacement for my existing router (at this stage) - just for wireless backups of my Macs.
    If this is not possible, or practicable, are there other alternatives that I should explore? (non-cloud)
    Thanks in advance
    Steven
    PS
    Boring background:
    I'm in a rental property with a woefully inadequate number of plugs in practical places. In addition there is only one phone socket. The result being insufficient safe space to have the existing router, and the Airport TC along with the existing electrical items.

    Unfortunately, Apple designed the Time Capsule to connect to a modem or modem/router using an Ethernet connection.
    If you do this, you do have the option of turning off the wireless on the Time Capsule and using your existing wireless for backups. Backups will be automatic this way, in the background. The Time Capsule could be located anywhere an Ethernet cable will reach.....up to 300+ feet or about 100 meters.
    The other option.....not recommended and not convenient at all.....is to set up the Time Capsule......without an Ethernet connection and then have the Time Capsule provide a wireless network that would not have Internet access.
    So, when you wanted to back up, you would have to manually "switch" to the Time Capsule network for that process, then once the backup was done, manually "switch" back again to your normal wireless network for normal operations.  A real mess, not to mention the possibility of wireless interference between the networks that may create other issues.

Maybe you are looking for

  • Can DW CS5 automate the creation of a link based on the text in the link?

    Here's the situation.  I often find myself creating blocks of code like this: <a href="home?searchString=some text"><img src="..."></a> <a href="home?searchString=some text">some text</a> Is there a quick, painless way to type the "some text" part on

  • Connecting a Samsun Mini DV Camcorder VP-D381

    Hi there. I'm trying to capture footage from a Samsung Mini DV Camcorder Model VP-D381. I'm using Premiere Pro CS3. When I go into the capture window it says capture device offline. I'm using a IEEE 1394 Firewire connection on my Desktop PC, however

  • To fix the length of a textfield for user to enter date

    hi, i need to display a textfield for user to enter the date in the format MM/DD/YY.With the slash in between present and fixed and the possibility of entering only 2 digit figures for the month,day n' year.I am using JTextField .how can i acheive th

  • WPC Render Error

    There appear to be some similar errors to this one, but they were easily solved using XLST Helper settings.  This one is strange to me. I am getting the following error for any item that's running through an XSLT: Cannot render container : An error o

  • Geturl not working of ferris wheel effect

    Hi, Thanks to Rob i have managed to get the effect i want and he has kindly given me the code to add a geturl to each of the images on the ferris wheel effect. The only thing is that when i view it it does not work so maybe i am missing somthing, see