Can not enable HDD Protection

When I open the HDD Protection the window opens but it is grayed out and "OFF" is selected, why is it grayed out? How to I activate it? Please & Thankyou.

Hi
> I installed most of tools and utillites
What tools have you installed exactly?
For the Toshiba tools you have to install Common Modules first. Its necessary for all other tools. Check this!
Furthermore are you sure that Satellite Pro U200 is equipped with HDD protection?

Similar Messages

Can not find HDD protection service

Hello,
I have Satellite pro u 200. I have instaled new system (windows xp professional service pack 3). I installed most of tools and utillites and all work ok, but I have a problem with HDD protection. I doesn't start with the system. When I try to open it or open settings windows pops and it says
TOSHIBA HDD Protection - Setting Utility
Can not find HDD Protection Service.
OK
What can I do?

Hi
> I installed most of tools and utillites
What tools have you installed exactly?
For the Toshiba tools you have to install Common Modules first. Its necessary for all other tools. Check this!
Furthermore are you sure that Satellite Pro U200 is equipped with HDD protection?

My iPhone 4s, I can not enable the wifi

The same problem presents me with my iPhone 4, I can not enable the wifi, and the operator said that my warranty expired and I refuse to think that Apple just build these modern devices to last exactly one year, whom I am very grateful can help with this problem, I need to know who I can contact my mail [email protected] regards

See if this helps
http://support.apple.com/kb/TS1559
If doesn't, you are looking at hardware failure.

Since updating to Firefox 3.6.15, I can no longer print coupons from SmartSource. The error message is that Java is not detected. The check box is longer showing in the Options/Content of this version of Firefox, so I can not enable it.

# Question
Since updating to Firefox 3.6.15, I can no longer print coupons from SmartSource. The error message is that Java is not detected. The check box is longer showing in the Options/Content of this version of Firefox, so I can not enable it.

Same PC as I used to post the question. When I go to the "plug in check" page, it shows I am up to date and it is not disabled.
Java(TM) Platform SE 6 U24
Next Generation Java Plug-in 1.6.0_24 for Mozilla browsers 1.6.0.24

I have a problem with my iPhone 5 stopped working the sleep / power and simultaneously refused to obey the HOME button. I can not use either one or the other. I can not enable or disable the device, display lights up when you plug the charger. same displa

I have a problem with my iPhone 5 stopped working the sleep / power and simultaneously refused to obey the HOME button. I can not use either one or the other. I can not enable or disable the device, display lights up when you plug the charger. same display works fine as it is surprising. or maybe someone knows what is the reason for this? is there any way to solve this problem?

More than likely its a hardware issue, I have never encountered such a problem and best bet is to just go get it replaced. If you have insurance on your device apple will replace it as long as there was no water damage, if you dont have insurance they will charge $200 more or less. Hope you get it fixed

Can not enable fonts for User library in Font Book

Hi all,
For some reason I can not enable the user library in the font book using the options in the font book. This means that the User Library is "off". I have tried the following but none of them have worked:
* Reboot.
* Delete the Font preferance file.
* Undo the font book via booting in safe mode and then rebooting in normal mode. Delete the trash which contains the font cache.
* Manually insert fonts into User>Library>Fonts and restart.
* Manually empty user fonts folder and re-insert fonts back in.
* Delete the user fonts folder and re-create it and insert all fonts back in
Have also tried a few combinations of the above but none of them have worked. I do not want to use the system library fonts folder as this machine is on a network and the users should not have admin rights to their machines.
I have also checked the user rights to the user fonts folder and all seems ok there.
Does anyone know how to solve this problem so that I can enable the User font library?
Any help would be much appreciated.
Thanks
Slack

I have found that for me, on both a PowerMac G5 and an Intel iMac, both running 10.4.8 with all updates, turning on FileVault reliably causes the problem. I.E., if FontBook is working fine on an account which does not have FileVault turned on and I turn on FileVault, then the User collection in FontBook is greyed out and Enable "User" doesn't work. If FileVault is on, none of the suggested work-arounds that I have read about in these discussions or in Apple's support articles help.
Sometimes, turning off FileVault is sufficient. Other times, I must turn off FileVault and follow the work-around in http://docs.info.apple.com/article.html?artnum=302551 . Sometimes, I must turn off FileVault, throw away the FontBook preferences and restart.

I can not enable bluetooth on Iphone 4

I can not enable bluetooth on Iphone 4. Attempt enabled in settings, bluetooth and awaits income. (not displayed tab)

qfyerko wrote:
Attempt enabled in settings, bluetooth and awaits income.
Then pay it.
What is the real issue? Post in your native language if you have problems communicating in English.

Can not enable wi-fi on ipad 2. Any suggestions?

I can not enable wi-fi on my new ipad 2. I have tried resetting network settings & restoring settings, but wi-fi remains greyed out under settings and is listed as N/A under settings-about. Any suggestions?

have you tried to see if a reboot fix it?
http://support.apple.com/kb/ht1430

HT4236 I can not enable selected photos to sync to my iphone 5. It is greyed out. I do not want to sync my entire iPhoto library.. help!

I can not enable selected photos to sync to my iphone 5. It is greyed out. I do not want to sync my entire iPhoto library.. help!

Guys, I found another user and what he said to do worked!!! I have copied the information below:
This was 1 of the things that happend to me too, the other one was that at the bottom of the itunes page were it says all the memory info, it marked that I had over 3gb of other memory wich I didn't.
Anyways what I did was to unmark the calendar, contacts etc. ( so that they wont sync with the computer ), pressed apply, then I marked all of them again, apply again and for last I pressed Sync wich is at the bottom right coner by the apply botton.
I'm not sure that had anything to do with it but it worked, my music appeard both of my itunes playlists and the ones I bought in itunes. Also the other memory dissapeard and it's all good.
I'm not sure this will help you but thats my 5 cents, if the problem continues its better to call customer service and ask for a technician.
Hope your problem gets solved. Have a nice day.

Can not enable tag-switching on the router

Good day for all,
i have 7206 g1 router with 7200 Software (C7200-JK9S-M), Version 12.3(4)T4 (enterprise)
and i can not enable mpls.
Router(config)#int gigabitEthernet 0/2.102
Router(config-subif)#mpls ip
% Tag switching not supported on interface GigabitEthernet0/2.102
this error on all interfaces
what is the problem? (cef enable)
Thank You

I have 2 identical 7206VXR, same IOS, same PAs
And one of em allows tag-switching on FasteEthernet 0/0.30 (dot1q), other - doesnt :(
--- rtr 1 ----
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-P-M), Version 12.2(18)S5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Sat 08-May-04 10:43 by nmasa
Image text-base: 0x60008FE0, data-base: 0x6151E000
ROM: System Bootstrap, Version 12.0(19990210:195103) [12.0XE 105], DEVELOPMENT SOFTWARE
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(18)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TV3 uptime is 3 weeks, 14 hours, 28 minutes
System returned to ROM by reload at 23:02:24 EEST Thu Aug 12 2004
System image file is "slot0:c7200-p-mz.122-18.S5.bin"
Last reload reason: Reload command
cisco 7206VXR (NPE300) processor (revision D) with 229376K/65536K bytes of memory.
Processor board ID 21265679
R7000 CPU at 262Mhz, Implementation 39, Rev 2.1, 256KB L2 Cache
6 slot VXR midplane, Version 2.0
Last reset from power-on
Channelized E1, Version 1.0.
X.25 software, Version 3.0.0.
Bridging software.
Primary Rate ISDN software, Version 1.1.
PCI bus mb0_mb1 has 200 bandwidth points
PCI bus mb2 has 0 bandwidth points
1 FastEthernet/IEEE 802.3 interface(s)
53 Serial network interface(s)
48 Channelized E1/PRI port(s)
125K bytes of non-volatile configuration memory.
20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x2112
--- rtr 2 ---
Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-P-M), Version 12.2(18)S5, RELEASE SOFTWARE (fc1)
Technical Support: http://www.cisco.com/techsupport
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Sat 08-May-04 10:43 by nmasa
Image text-base: 0x60008FE0, data-base: 0x6151E000
ROM: System Bootstrap, Version 12.0(19990210:195103) [12.0XE 105], DEVELOPMENT SOFTWARE
BOOTLDR: 7200 Software (C7200-BOOT-M), Version 12.0(9)S, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TV1 uptime is 3 weeks, 14 hours, 39 minutes
System returned to ROM by reload at 22:51:22 EEST Thu Aug 12 2004
System restarted at 22:53:54 EEST Thu Aug 12 2004
System image file is "slot0:c7200-p-mz.122-18.S5.bin"
Last reload reason: Reload command
cisco 7206VXR (NPE300) processor (revision D) with 229376K/65536K bytes of memory.
Processor board ID 18285647
R7000 CPU at 262Mhz, Implementation 39, Rev 1.0, 256KB L2 Cache
6 slot VXR midplane, Version 2.0
Last reset from power-on
Channelized E1, Version 1.0.
X.25 software, Version 3.0.0.
Bridging software.
Primary Rate ISDN software, Version 1.1.
PCI bus mb0_mb1 has 200 bandwidth points
PCI bus mb2 has 0 bandwidth points
1 FastEthernet/IEEE 802.3 interface(s)
68 Serial network interface(s)
48 Channelized E1/PRI port(s)
125K bytes of non-volatile configuration memory.
20480K bytes of Flash PCMCIA card at slot 0 (Sector size 128K).
4096K bytes of Flash internal SIMM (Sector size 256K).
Configuration register is 0x102
TV3(config)#in fas 0/0.30
TV3(config-subif)#tag ip
% Tag switching not supported on interface FastEthernet0/0.30

Can't enable HDD write caching

I recently upgraded my PC. I am using Vista x64 on a MSI P35 mobo and a Seagate SATA II 250GB drive and a 36GB Raptor (SATA I). It has the newest 1.8 BIOS and newest Intel AHCI drivers.
The problem is this: I can't enable write caching on either hard drive in the Device Manager. It is there to check but below it it says something like "This device does not support write caching."
Now I am not dumb, and the Raptor used to have write caching enabled on my old nForce4 mobo in Vista. I have AHCI enabled in the mobo BIOS too. Does anybody kno what is causing this?
Also, does anybody knw of any good utilities that will tell me the fatures that are enabled (NCQ, SATA 3.0, etc..) that doesn't require an install? I just like to execute utilities and get results without installing stuff (like CPU-Z and GPU-Z).

Hi,
By default, write caching is disabled on a disk that contains the Active Directory database (Ntds.dit). Also, write caching is disabled on a disk that contains the Active Directory log files. By doing this, you enhance the reliability of the Active
Directory files.
Thus if it is a DC, try to move the Active Directory database and the Active Directory log files off of a disk in which you need to enable write caching.
If you have any feedback on our support, please send to [email protected]

Can not "Enable disk use" on second computer

We have two computers. One was our main system (and had all my downloaded music) and a newer laptop with nothing but loaded CD's.
I am now attempting to transfer everything onto my laptop, (This is my primary computer.) but when I select "Options" the "Enable Disk Use" is checked but greyed out and can not be accessed.
Everything else works fine. The outlook syncs up and I can organize music. I just can't utilize the disk.
Any advise?
Windows XP Pro

I can relate...sort of! My iTunes doesn't even HAVE that option. Can you believe it??? It's a brand new (although outdated) 40gb HP iPod, and I'm running HP version of iTunes 6. The manual says how I should enable (configure) the iTunes for use as hard disk--but it failed to tell me that no freaking icon would appear in that little corner. FRUSTRATED
Sigh.

Microsoft office 2011 under Mavericks: can not open password protected files

I think that it all started with the installation of Mavericks.
I have a few Microsoft office 2011 files (excel and word) that are passord protected. Now, it's telling me that the file can not be opened due to an encrytion sheme that is not available in this country (I'm in Canada).
I've re-installed Microsoft Office, but that did not solve the problem.
Thanks

Same problem for me, I had two password-protected Word files and both won't open now. It started after i tried to add support for an additional language (spanish), but removing it afterwards did not fix the problem.
OS 10.9, Office mac 2008 AND 2011 wont open the files BUT Preview can open it! (BTW this saved me)

Can not enable web services. printer on the network. default ip not connecting using auto ip

B210 - have tried resetting defaults . default IP address will not connect to network with auto IP had to set IP addrtess manually something similiar to the properties on the verzion hot spot. can not disable web services - never enabled.
no Primary or secondary DNS server. not sure if this is problem. can print ok thru network.
This question was solved.
View Solution.

Hey bobupton!
Try going into the printer's EWS and using Google's public DNS servers (8.8.8.8 and 8.8.4.4). It sounds like you know what you're doing so I skipped a few steps on how to get there but if you need more help with it let me know!
If I have solved your issue, please feel free to provide kudos and make sure you mark this thread as solution provided!
Although I work for HP, my posts and replies are my own opinion and not those of HP.

Re: Satellite Pro U200 - Can't install HDD protection Utility?

hi
Knows somwonw why I cannot install:
18/08/08
HDD Protection Utility
Toshiba Windows Vista 32 Bit 2.0.0.7 World Wide
on my Satellite Pro U200 PLUA1E-02802QS4 with Vista Business 32-bit?

All Toshiba stuff available on download page is the same as in recovery image.
All tools are tested and I don't see any reason why you should not be able to install this utility.
Is some error message shown?

Can not enable HDD Protection

Similar Messages

Maybe you are looking for