Can not install latest ATI mobility Radeon x1600 display driver for my Satellite A100

Hello,
my Satellite A100-704 PSAA9E is equipped with the ATI Mobility Radeon X1600 display graphic card, for which ATI provides a new driver, named Catalyst 8.3. My issue is that when I run the verification software I get a message telling me that driver is not suitable to be installed on my system.
Is that any information available about it? Can I still install the new Catalyst driver or it's better if I don't? Oh, the current driver I have running on my notebook is the one downloaded from the Toshiba site, 8.292 I believe.
Any information is appreciated. Thank you very much.

> Can I still install the new Catalyst driver or it's better if I don't?
I dont recommend the installation of any 3rd party graphic drivers. The fact is that such drivers are not tested and not certified and nobody knows how such driver would affect the notebooks hardware in worst case it could lead to the GPU overheating and damage
best regards

Similar Messages

  • Where do I get ATI mobility Radeon 9600/9700 Driver for Satellite M30?

    Hey ho, had to reinstall winxp now i cant get any drievrs for the graphic card, I tried ATI they got the ones i need, but say they dont support toshiba notebooks and i cant install or even download the driver i need.i looked everywhere . on this site in the drivers section i cant find any ati drivers or any graphic drivers at all...Anyone got a Link for me plz?
    Ati mobility Radeon 9600/9700 Driver for Satellite M30
    Hope this works somehow been looking all day long now :(

    Hi,
    its your lucky day my friend.
    Check this sites and download the drivers you need:
    http://www.laptopvideo2go.com/
    http://www.omegadrivers.net/
    The drivers are native Nvidia/ATI drivers but the *.inf files (the files where the hardware information and the settings for the cards are listed) were fitted for mobile systems. That means you can install them on your machine and by the way you will get the most actual drivers.
    Greets

  • ATI Mobility Radeon X1600 graphics card Windows 8 driver missing

    I just installed Windows 8 Enterprise Trial version on HP nx9420 laptop (2GHz dual core prosessor, 4gb memory, ATI Motility Radeon X1600 graphics card with 256mb own memory, 1680x1050 native display resolution) on second partition, side by side with existing
    Windows 7. 
    Installation succeeded perfect, except Windows 8 couldn't install, nor did find from Windows Update display driver for ATI Mobility Radeon X1600 graphics card. Only Microsoft generic display driver was installed and it offered maximum 1450x800 resolution,
    so not laptops native 1680x1050 screen resolution. 
    Windows 7 can install working ATI driver right from Windows Update for that graphics card (version 8.561.0.0 dated 1.12.2008). 
    Laptop manufacturer HP has latest, old driver for Vista (version 8.453.0.0 dated 22.1.2008), so I installed that, selecting compatibility mode Vista with setup-program in Windows 8. That installed, but seems to have some problems, telling of missing library,
    maybe with some ATI extra diplay manager software and C++ 2005 library, that it installed. 
    MY QUESTION: Is there some problems with Windows 8 and that ATI Mobility Radeon X1600 graphics card? Why isn't the Windows 7 -version of ATI mobility radeon X1600 display driver available in Windows Update for Windows 8 too? 

    Thank you all of your thanks. 
    I can confirm that this solution works with Windows 10 Technology/Insider preview too. And surely works with forthcoming Windows RTM too. 
    Windows 8.1 and Windows 10 TP work both like a charm with nearly 10 years old HP Compaq nx9420 laptop, with Intel Core 2 Duo and ATI Mobility Radeon X1600 display adapter. Nice co-operation of "old" hardware and very Modern Windows OS.
    So in brief:
    If you have laptop with ATI Mobility Radeon X1600 or other X1000-series display adapter and
    you want to install Windows 8, 8.1 or 10, do this:
    0) First just install Windows 8.x/10. It will install Microsoft Generic display driver, but that doesn't support full resolution of ATI Mobility Radeon X1000 -series - for example it may show maximum 1400x1050 -resolution, thus your laptop display and Radeon
    X1000 may support native 1650x1050, but you can't obtain that resolution with that Microsoft generic driver. So you need ATI-driver and you can get it this way: 
    1) With Internet Explorer (this doesn't work with other browsers) go to
    Microsoft Update -catalog:   http://catalog.update.microsoft.com/
    2) Search "ATI Mobility Radeon X1600"
      (or X1300, X1800 etc)
    3) Sort search results by date (last update -column), latest on top. You will see drivers for Windows 7
    - they will work with Windows 8.x and 10 too. There is certainly two of them; other is 32 bit only and other is 64 bit dirver.
    4) Select proper driver version of them, according your Windows 32 or 64 bit, so click Add
    5) At top-right click Show basket and then download those driver packages to your computer. They are cab-file
    -packages. 
    6) Obtain 7-zip -utility, install it and with it unpack that cab-driver package on folder with its package-name.
    7) On start of taskbar, right mouse button click Windows-Start and then select Hardware management. On
    Hardware management -window open Display adapter -section, then mouse right click Microsoft adapter and select Update driver. Then on next window, select search driver from computer. 
    8) Browse on folder, where you unpacked ATI driver (on stage 6 earlier) and select Next ... that updates
    driver, on the go and you don't need even to reboot Windows. 
    9) Now you have proper ATI Mobility Radeon -driver in use. It  surely sets automatically resolution
    according your laptop screen (so recommended native resolution of screen panel) or you can select that on diplay settings. 
    Extra: For that Windows 8.x/10 boot works fine too, do this too: 
    Seems that Windows 8.x (and Windows 10 too), with their hybrid-shutdown -functionality, require some support of the display adapter, that ATI Radeon Mobility x1000 -series don't have. 
    So the solution is to disable that Windows 8.x (or Windows 10) hybrid boot -functionality (that is quicker boot) and to use "normal boot". 
    You can fix that this way:
    - at end of Taskbar click battery/power icon and select Power settings
    - navigate to power and sleep settings
    - either at bottom of those settings, or in Win10 more power settings, select power buttons functionality/settings (so what power button, sleep button or closing laptop screen does)
    - at bottom of those settings is shutdown options (or with similar name). uncheck "use quick boot" -settings (for to uncheck that you may need to click first upper "changing disabled settings" (or similar name) at top or windows) 
    (I recommend to check Hibernate at the same time too, because that is usefull)
    - then Save settings and reboot Windows and you have got rid of that problem that Windows 8.x/10 don't show Lock screen, now it does.
    Boot takes just a little longer, so practically no problem. And if you need quicker boot with laptop, use Hibernate-state, so don't shut down your laptop, but instead put it into Hibernate-state (that is better than Sleep mode, because Hibernate-mode doesn't
    consume battery-power, like Sleep-mode does)

  • ATI Mobility Radeon X1600 compatible with Motion?

    Hi, is this card in the MacBook Pro and the version in the iMac compatible with running Motion?
    ATI Mobility Radeon X1600 or does it need a bit 'more'?
    thanks.

    Search is your friend:
    http://discussions.apple.com/thread.jspa?messageID=1809447&#1809447
    Patrick

  • Hi, i have question about my macBook pro.  I have a somehow managed to delete a driver or no, so I can not install new software updates. I have tried for several hours to fixe it on OS X tools-Disc Tools. anyone has a clue about this more than I have.

    I have a somehow managed to delete a driver or no, so I can not install new software updates. I have tried for several hours to fixe it on OS X tools-Disc Tools. anyone has a clue about this more than I have about Mac´crack that **** formatted and has really nothing to the HD. what do I do??
    <Edited by Host>

    Cami87,
    which model MacBook Pro do you have, and which version of OS X is installed on it?

  • I can not install the Apple Mobile Device

    I do not get completely install the iTunes 10.7, I have completely removed the previous version's instructions itunes support and after doing this several times always end up like me not install the Apple Mobile Device and iTunes so I recognized my devices. Can anyone help?. Thank you.

    Let's try a standalone Apple Mobile Device Support install. It still might not install, but fingers crossed any error messages will give us a better idea of the underlying cause of why it's not installing under normal conditions.
    Download and save a copy of the iTunesSetup.exe (or iTunes64setup.exe) installer file to your hard drive:
    http://www.apple.com/itunes/download/
    Download and install the free trial version of WinRAR:
    http://www.rarlab.com/
    Right-click the iTunesSetup.exe (or iTunes64setup.exe), and select "Extract to iTunesSetup" (or "Extract to iTunes64Setup"). WinRAR will expand the contents of the file into a folder called "iTunesSetup" (or "iTunes64Setup").
    Go into the folder and doubleclick the AppleMobileDeviceSupport.msi (or AppleMobileDeviceSupport64.msi) to do a standalone AMDS install.
    (If it offers you the choice to remove or repair, choose "Remove", and if the uninstall goes through successfully, see if you can reinstall by doubleclicking the AppleMobileDeviceSupport.msi again.)
    Does it install (or uninstall and then reinstall) properly for you? If so, can you get a normal iTunes install to go through properly now?
    If instead you get an error message during the install (or uninstall), let us know what it says. (Precise text, please.)

  • Can not installed mountain lion msg" macintosh hd is using for time machine back up" please help

    I downloaded mountain lion but can not install, msg" macintosh HD is using for time machine back up , how can I change that...thanks

    Somehow, a Backups.backupdb folder got created on your startup drive.
    You won't find it via a Spotlight or Finder search, so open your internal HD via the Finder.
    That folder is at the top level.  Just delete it.

  • Can Not  installed latest iTunes 10.5.2 for Windows XP

    To System support,
    I am having trouble installed latest iTunes 10.5.2 for Windows XP. When I start install the exe file, I got an error message:
    “There is problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor.”
    Could someone tell me why I can’t install iTunes 10.5.2?
    I even fellow the trouble shooting from iTunes page by uninstall the older version of iTunes. Now I can’t even link my iPhone or iPad now. Please advise me on what is missing in my computer for costing this issue. Thanks for all your supports.
    My computer inf:
    System:
    Microsoft Windows XP
    Professional
    Version 2002
    Service Pack 3
    Computer:
    Intell(R) Core 2 Duo CPU
    T7500 @ 2.20GHz
    2.19 GHz, 1.50 GB of RAM

    “There is problem with this Windows Installer package. A program run as part of the setup did not finish as expected. Contact your support personnel or package vendor.”
    Perhaps let's first try updating your Apple Software Update.
    Launch Apple Software Update ("Start > All Programs > Apple Software Update"). Does it launch and offer you a newer version of Apple Software Update? If so, choose to install just that update to Apple Software Update. (Deselect any other software offered at the same time.)
    If the ASU update goes through okay, try another iTunes install. Does it go through without the errors this time?

  • Can not find out Ethernet Controler & SM Bus Controller Driver for P 1000-1404TU Notebook PC

    Hi ;
    I just purchase a laptop as subject, i installed window 7 64bit and some drivers, but remain 2 drivers as bellow i can not find out in HP Website
    Ethernet Controler (wire LAN adapter)
    SM Bus Controller.
    Could some one help me ?
    Many thanks .
    This question was solved.
    View Solution.

    Hi,
    Please try:
    1. http://ftp.hp.com/pub/softpaq/sp52501-53000/sp52799.exe
    2.  http://ftp.hp.com/pub/softpaq/sp56501-57000/sp56517.exe
      & http://ftp.hp.com/pub/softpaq/sp46501-47000/sp46748.exe
    Regards.
    BH
    **Click the KUDOS thumb up on the left to say 'Thanks'**
    Make it easier for other people to find solutions by marking a Reply 'Accept as Solution' if it solves your problem.

  • ATI Mobility Radeon X1300 video driver update

    I updated my video driver using the Lenovo update.  The updated driver, 8.533.3.1-081110a-075168 79d177ww.exe is causing me to have extremely slow response time that I didn't experience previously. I am running with XP Professional (SP2).  Is there a way to go to a back-level driver?  Even typing this note is painfully slow. I have the latest BIOS and Presentation Manager.

    you could also download the Omega ATI catalyst driver, which works just as great and have some more features. 
    Regards,
    Jin Li
    May this year, be the year of 'DO'!
    I am a volunteer, and not a paid staff of Lenovo or Microsoft

  • Need new ATI Radeon 1400 display driver for Satellite A100-788 PSAA9E

    Hello ,
    I search for New drivers for my ATI radeon mobility 1400 because in toshiba.com the last date drivers is 13/09/07.
    Thx.

    Hi
    This seems to be a Toshiba European notebook series and therefore you should search on the Toshiba European driver page.
    The newest ATI driver on the European driver page is a version 8.31.100.3.2 fro Vista and v 8.292-038742C for Win XP
    Unfortunately newer driver is not available
    Greetings

  • T42p ATI Mobility Radeon Fire GL T2

    When I try to install the ATI Mobility Radeon Fire GL T2 driver from ATI's website, why does it not work? It claims the hardware is not present.
    Message Edited by rwing14 on 07-31-2008 12:30 PM

    Have you unpacked the driver from the correct directory after downloading it, it should be something like C>Drivers>Win>Video (or Monitor)?
    Cheers,
    George
    In daily use: R60F, R500F, T61, T410
    Collecting dust: T60
    Enjoying retirement: A31p, T42p,
    Non-ThinkPads: Panasonic CF-31 & CF-52, HP 8760W
    Starting Thursday, 08/14/2014 I'll be away from the forums until further notice. Please do NOT send private messages since I won't be able to read them. Thank you.

  • ATI Mobility Radeon Premium Graphics DirectX 11

    Please give a link for DirectX 11 download.

    Dear sir,
            Below mention system I Purchased from  Doha -QATAR
      I Need 
    ATI Mobility Radeon Premium Graphics DirectX11
                                               For 
                      Model No      :-  HP Pavilion dv3 4303se
                      Serial No.     :-  [edited by Moderator]
                      Product No.  :-  LE428EA#ABV
       Reply as soon as possible
    Thank you

  • Satellite A100 (PSAA9E) - Can't install display driver for Windows 7

    I have a problem with installing official Toshiba Windows 7 x32 ATI x1600 driver.
    After unpacking it should install.exe be executed, I believe, but it's not; nothing happens. Going to Setup.exe with manual install, then I don't see Catalyst Control Center & Display Driver in the list, just Catalyst install Manager & vcredist. After installation these components (CCC & DD) are not present.
    Any ideas?
    P.S. Same problem with official Toshiba Vista32 ATI x1600 driver.

    Hi mate,
    Have you already installed other drivers for the notebook? I mean the chipset driver, this driver must be installed first.
    And are you sure that you have ATI display driver? Some Satellite A100 models were delivered with nVidia graphic card as far as I know.
    By the way, what happens if you install the driver manual in device manager via advanced installation?

  • [Solved] ATI Mobility Radeon HD 2300 Problem - fglrx not loading

    I changed the currently unreliable GS 8600 nvidia card in my laptop to a compatible old ATI HD 2300 card from a similar model laptop but I can't get the Catalyst drivers to work with it. The open source driver xf86-video-ati works well with it for basic use, but is not so good for 3D. This card should work with an Amilo xi-2428 & has done for other people who have developed faulty nvidia cards.
    I have the legacy driver installed from AUR (Catalyst-total-hd234k) and have enabled Vi0L0's [xorg112] server properly in pacman.conf & downgraded to Xorg-server 1.12. I also tried downgrading to Xorg-server 1.11 & reinstalling the drivers from AUR. Plus I have enabled and tried Vi0L0's [catalyst-hd234k] repo in place of the AUR package each time too. Made no difference. I've blacklisted radeon too.
    When the laptop boots systemd-modules-load.service shows as failed.
    $ sudo systemctl --failed
    UNIT LOAD ACTIVE SUB DESCRIPTION
    systemd-modules-load.service loaded failed failed Load Kernel Modules
    LOAD = Reflects whether the unit definition was properly loaded.
    ACTIVE = The high-level unit activation state, i.e. generalization of SUB.
    SUB = The low-level unit activation state, values depend on unit type.
    1 loaded units listed. Pass --all to see loaded but inactive units, too.
    To show all installed unit files use 'systemctl list-unit-files'.
    [fyn@Finnix ~]$ systemctl status systemd-modules-load
    systemd-modules-load.service - Load Kernel Modules
    Loaded: loaded (/usr/lib/systemd/system/systemd-modules-load.service; static)
    Active: failed (Result: exit-code) since Wed, 2012-12-19 15:29:57 GMT; 7min ago
    Docs: man:systemd-modules-load.service(8)
    man:modules-load.d(5)
    Process: 121 ExecStart=/usr/lib/systemd/systemd-modules-load (code=exited, status=1/FAILURE)
    It is only the fglrx module which fails to load:-
    $ sudo journalctl -b _PID=121
    -- Logs begin at Fri, 2012-10-26 09:21:22 GMT, end at Wed, 2012-12-19 15:38:07 G
    Dec 19 15:29:56 Finnix systemd-modules-load[121]: Failed to insert 'fglrx': No such device
    Dec 19 15:29:56 Finnix systemd-modules-load[121]: Inserted module 'nfs'
    Dec 19 15:29:57 Finnix systemd-modules-load[121]: Inserted module 'vboxnetflt'
    I have no idea how to get fglrx to load & since it fails to load so early during boot I doubt the problem lies with my Xorg.conf. Likewise neither aticonfig or the ATI control center work.
    aticonfig: No supported adapters detected
    amdcccle just give this message
    "There was a problem initializing Catalyst Control Center Linux edition. It could be caused by the following.
    No AMD graphics driver is installed, or the AMD driver is not functioning properly.
    Please install the AMD driver appropriate for you AMD hardware, or configure using aticonfig."
    Graphic card info
    $ hwinfo --gfxcard
    27: PCI 100.0: 0300 VGA compatible controller (VGA)
    [Created at pci.319]
    Unique ID: VCu0.SZRyUClQNUF
    Parent ID: vSkL.rRA4AOLb3d5
    SysFS ID: /devices/pci0000:00/0000:00:01.0/0000:01:00.0
    SysFS BusID: 0000:01:00.0
    Hardware Class: graphics card
    Model: "ATI M71 [Mobility Radeon X2100]"
    Vendor: pci 0x1002 "ATI Technologies Inc"
    Device: pci 0x7210 "M71 [Mobility Radeon X2100]"
    SubVendor: pci 0x1734 "Fujitsu Technology Solutions"
    SubDevice: pci 0x1107
    Revision: 0xce
    Memory Range: 0xd0000000-0xdfffffff (ro,non-prefetchable)
    I/O Ports: 0x2000-0x2fff (rw)
    Memory Range: 0xcfef0000-0xcfefffff (rw,non-prefetchable)
    Memory Range: 0xcfe00000-0xcfe1ffff (ro,non-prefetchable,disabled)
    IRQ: 5 (no events)
    I/O Ports: 0x3c0-0x3df (rw)
    Module Alias: "pci:v00001002d00007210sv00001734sd00001107bc03sc00i00"
    Driver Info #0:
    Driver Status: radeon is not active
    Driver Activation Cmd: "modprobe radeon"
    Config Status: cfg=new, avail=yes, need=no, active=unknown
    Attached to: #8 (PCI bridge)
    Primary display adapter: #27
    my Xorg.conf derived mainly from a newly generated config using Xorg :0 -configure
    Section "ServerLayout"
    Identifier "Arch"
    Screen 0 "Screen0" 0 0
    Screen 1 "Screen1" RightOf "Screen0"
    InputDevice "Mouse0" "CorePointer"
    InputDevice "Keyboard0" "CoreKeyboard"
    EndSection
    Section "Files"
    ModulePath "/usr/lib/xorg/modules"
    FontPath "/usr/share/fonts/misc/"
    FontPath "/usr/share/fonts/TTF/"
    FontPath "/usr/share/fonts/OTF/"
    FontPath "/usr/share/fonts/Type1/"
    FontPath "/usr/share/fonts/100dpi/"
    FontPath "/usr/share/fonts/75dpi/"
    EndSection
    Section "Module"
    Load "glx"
    EndSection
    Section "InputDevice"
    Identifier "Keyboard0"
    Driver "kbd"
    EndSection
    Section "InputDevice"
    Identifier "Mouse0"
    Driver "mouse"
    Option "Protocol" "auto"
    Option "Device" "/dev/input/mice"
    Option "ZAxisMapping" "4 5 6 7"
    EndSection
    Section "Monitor"
    Identifier "Monitor0"
    VendorName "Monitor Vendor"
    ModelName "Monitor Model"
    EndSection
    Section "Monitor"
    Identifier "Monitor1"
    VendorName "Monitor Vendor"
    ModelName "Monitor Model"
    EndSection
    Section "Device"
    ### Available Driver options are:-
    ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
    ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
    ### <percent>: "<f>%"
    ### [arg]: arg optional
    #Option "NoAccel" # [<bool>]
    #Option "SWcursor" # [<bool>]
    #Option "EnablePageFlip" # [<bool>]
    #Option "AccelDFS" # [<bool>]
    #Option "IgnoreEDID" # [<bool>]
    #Option "ColorTiling" # [<bool>]
    #Option "ColorTiling2D" # [<bool>]
    #Option "RenderAccel" # [<bool>]
    #Option "SubPixelOrder" # [<str>]
    #Option "AccelMethod" # <str>
    #Option "DRI" # [<bool>]
    #Option "TVStandard" # <str>
    #Option "EXAVSync" # [<bool>]
    #Option "EXAPixmaps" # [<bool>]
    #Option "ZaphodHeads" # <str>
    #Option "EnablePageFlip" # [<bool>]
    #Option "SwapbuffersWait" # [<bool>]
    Identifier "Card0"
    Driver "fglrx" # Essential.
    # Driver "vesa"
    BusID "PCI:1:0:0" # Recommended if autodetect fails.
    Option "OpenGLOverlay" "0" ##
    Option "XAANoOffscreenPixmaps" "false" ##
    EndSection
    Section "Device"
    ### Available Driver options are:-
    ### Values: <i>: integer, <f>: float, <bool>: "True"/"False",
    ### <string>: "String", <freq>: "<f> Hz/kHz/MHz",
    ### <percent>: "<f>%"
    ### [arg]: arg optional
    #Option "ShadowFB" # [<bool>]
    #Option "DefaultRefresh" # [<bool>]
    #Option "ModeSetClearScreen" # [<bool>]
    Identifier "Card1"
    Driver "fglrx"
    # Driver "vesa"
    BusID "PCI:1:0:0"
    EndSection
    Section "Screen"
    Identifier "Screen0"
    Device "Card0"
    Monitor "Monitor0"
    DefaultDepth 24
    SubSection "Display"
    Viewport 0 0
    Depth 24 # Should not change from '24'
    Modes "1280x800" "1280x800" ## 1st value=default resolution, 2nd=maximum.
    Virtual 1664 1200 ## (x+64, y) to workaround potential OGL rect. artifacts/
    EndSubSection
    EndSection
    Section "Screen"
    Identifier "Screen1"
    Device "Card1"
    Monitor "Monitor1"
    SubSection "Display"
    Viewport 0 0
    Depth 1
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 4
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 8
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 15
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 16
    EndSubSection
    SubSection "Display"
    Viewport 0 0
    Depth 24
    EndSubSection
    EndSection
    Section "DRI"
    Mode 0666 # May help enable direct rendering.
    EndSection
    Xorg log
    [ 22.305]
    X.Org X Server 1.12.4
    Release Date: 2012-08-27
    [ 22.306] X Protocol Version 11, Revision 0
    [ 22.306] Build Operating System: Linux 3.4.8-1-ARCH x86_64
    [ 22.307] Current Operating System: Linux Finnix 3.6.10-1-ARCH #1 SMP PREEMPT Tue Dec 11 09:40:17 CET 2012 x86_64
    [ 22.307] Kernel command line: root=/dev/sda3 ro video=vesa:off vga=0x360 init=/usr/lib/systemd/systemd nomodeset
    [ 22.308] Build Date: 27 August 2012 08:04:39AM
    [ 22.308]
    [ 22.309] Current version of pixman: 0.28.2
    [ 22.309] Before reporting problems, check
    to make sure that you have the latest version.
    [ 22.310] Markers: (--) probed, (**) from config file, (==) default setting,
    (++) from command line, (!!) notice, (II) informational,
    (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
    [ 22.312] (==) Log file: "/var/log/Xorg.0.log", Time: Wed Dec 19 13:14:33 2012
    [ 22.312] (==) Using config file: "/etc/X11/xorg.conf"
    [ 22.313] (==) Using config directory: "/etc/X11/xorg.conf.d"
    [ 22.313] (==) ServerLayout "Arch"
    [ 22.313] (**) |-->Screen "Screen0" (0)
    [ 22.313] (**) | |-->Monitor "Monitor0"
    [ 22.313] (**) | |-->Device "Card0"
    [ 22.313] (**) |-->Screen "Screen1" (1)
    [ 22.313] (**) | |-->Monitor "Monitor1"
    [ 22.313] (**) | |-->Device "Card1"
    [ 22.313] (**) |-->Input Device "Mouse0"
    [ 22.313] (**) |-->Input Device "Keyboard0"
    [ 22.313] (==) Automatically adding devices
    [ 22.313] (==) Automatically enabling devices
    [ 22.313] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
    [ 22.313] Entry deleted from font path.
    [ 22.313] (WW) The directory "/usr/share/fonts/OTF/" does not exist.
    [ 22.313] Entry deleted from font path.
    [ 22.313] (**) FontPath set to:
    /usr/share/fonts/misc/,
    /usr/share/fonts/TTF/,
    /usr/share/fonts/Type1/,
    /usr/share/fonts/100dpi/,
    /usr/share/fonts/75dpi/,
    /usr/share/fonts/misc/,
    /usr/share/fonts/TTF/,
    /usr/share/fonts/Type1/,
    /usr/share/fonts/100dpi/,
    /usr/share/fonts/75dpi/
    [ 22.313] (**) ModulePath set to "/usr/lib/xorg/modules"
    [ 22.313] (WW) Hotplugging is on, devices using drivers 'kbd', 'mouse' or 'vmmouse' will be disabled.
    [ 22.313] (WW) Disabling Mouse0
    [ 22.314] (WW) Disabling Keyboard0
    [ 22.314] (II) Loader magic: 0x7c8b00
    [ 22.314] (II) Module ABI versions:
    [ 22.314] X.Org ANSI C Emulation: 0.4
    [ 22.314] X.Org Video Driver: 12.1
    [ 22.314] X.Org XInput driver : 16.0
    [ 22.314] X.Org Server Extension : 6.0
    [ 22.315] (--) PCI:*(0:1:0:0) 1002:7210:1734:1107 rev 206, Mem @ 0xd0000000/268435456, 0xcfef0000/65536, I/O @ 0x00002000/256, BIOS @ 0x????????/131072
    [ 22.315] (WW) Open ACPI failed (/var/run/acpid.socket) (No such file or directory)
    [ 22.315] (II) "extmod" will be loaded by default.
    [ 22.315] (II) "dbe" will be loaded by default.
    [ 22.315] (II) "glx" will be loaded. This was enabled by default and also specified in the config file.
    [ 22.315] (II) "record" will be loaded by default.
    [ 22.315] (II) "dri" will be loaded by default.
    [ 22.315] (II) "dri2" will be loaded by default.
    [ 22.315] (II) LoadModule: "glx"
    [ 22.315] (II) Loading /usr/lib/xorg/modules/extensions/libglx.so
    [ 22.315] (II) Module glx: vendor="Advanced Micro Devices, Inc."
    [ 22.315] compiled for 6.9.0, module version = 1.0.0
    [ 22.315] (II) Loading extension GLX
    [ 22.315] (II) LoadModule: "extmod"
    [ 22.315] (II) Loading /usr/lib/xorg/modules/extensions/libextmod.so
    [ 22.315] (II) Module extmod: vendor="X.Org Foundation"
    [ 22.315] compiled for 1.12.4, module version = 1.0.0
    [ 22.315] Module class: X.Org Server Extension
    [ 22.315] ABI class: X.Org Server Extension, version 6.0
    [ 22.315] (II) Loading extension MIT-SCREEN-SAVER
    [ 22.316] (II) Loading extension XFree86-VidModeExtension
    [ 22.316] (II) Loading extension XFree86-DGA
    [ 22.316] (II) Loading extension DPMS
    [ 22.316] (II) Loading extension XVideo
    [ 22.316] (II) Loading extension XVideo-MotionCompensation
    [ 22.316] (II) Loading extension X-Resource
    [ 22.316] (II) LoadModule: "dbe"
    [ 22.316] (II) Loading /usr/lib/xorg/modules/extensions/libdbe.so
    [ 22.316] (II) Module dbe: vendor="X.Org Foundation"
    [ 22.316] compiled for 1.12.4, module version = 1.0.0
    [ 22.316] Module class: X.Org Server Extension
    [ 22.316] ABI class: X.Org Server Extension, version 6.0
    [ 22.316] (II) Loading extension DOUBLE-BUFFER
    [ 22.316] (II) LoadModule: "record"
    [ 22.316] (II) Loading /usr/lib/xorg/modules/extensions/librecord.so
    [ 22.316] (II) Module record: vendor="X.Org Foundation"
    [ 22.316] compiled for 1.12.4, module version = 1.13.0
    [ 22.316] Module class: X.Org Server Extension
    [ 22.316] ABI class: X.Org Server Extension, version 6.0
    [ 22.316] (II) Loading extension RECORD
    [ 22.316] (II) LoadModule: "dri"
    [ 22.316] (II) Loading /usr/lib/xorg/modules/extensions/libdri.so
    [ 22.316] (II) Module dri: vendor="X.Org Foundation"
    [ 22.316] compiled for 1.12.4, module version = 1.0.0
    [ 22.316] ABI class: X.Org Server Extension, version 6.0
    [ 22.316] (II) Loading extension XFree86-DRI
    [ 22.316] (II) LoadModule: "dri2"
    [ 22.316] (II) Loading /usr/lib/xorg/modules/extensions/libdri2.so
    [ 22.317] (II) Module dri2: vendor="X.Org Foundation"
    [ 22.317] compiled for 1.12.4, module version = 1.2.0
    [ 22.317] ABI class: X.Org Server Extension, version 6.0
    [ 22.317] (II) Loading extension DRI2
    [ 22.317] (II) LoadModule: "fglrx"
    [ 22.317] (II) Loading /usr/lib/xorg/modules/drivers/fglrx_drv.so
    [ 22.333] (II) Module fglrx: vendor="FireGL - ATI Technologies Inc."
    [ 22.333] compiled for 1.4.99.906, module version = 8.97.2
    [ 22.333] Module class: X.Org Video Driver
    [ 22.333] (II) Loading sub module "fglrxdrm"
    [ 22.333] (II) LoadModule: "fglrxdrm"
    [ 22.333] (II) Loading /usr/lib/xorg/modules/linux/libfglrxdrm.so
    [ 22.333] (II) Module fglrxdrm: vendor="FireGL - ATI Technologies Inc."
    [ 22.333] compiled for 1.4.99.906, module version = 8.97.2
    [ 22.333] (II) ATI Proprietary Linux Driver Version Identifier:8.97.2
    [ 22.333] (II) ATI Proprietary Linux Driver Release Identifier: UNSUPPORTED-8.97.100.3
    [ 22.333] (II) ATI Proprietary Linux Driver Build Date: Jul 3 2012 23:56:30
    [ 22.333] (++) using VT number 1
    [ 22.334] (WW) Falling back to old probe method for fglrx
    [ 22.337] (II) Loading PCS database from /etc/ati/amdpcsdb
    [ 22.337] (EE) No supported AMD display adapters were found
    [ 22.337] (EE) No devices detected.
    [ 22.337]
    Fatal server error:
    [ 22.337] no screens found
    [ 22.337]
    Please consult the The X.Org Foundation support
    at
    for help.
    [ 22.337] Please also check the log file at "/var/log/Xorg.0.log" for additional information.
    [ 22.337]
    Solved. The  ATI Mobility Radeon HD 2300 was based on an earlier design & was not really one of the HD 2*** cards, even tho it was released as one (HD 2*** cards are R600 series while the HD 2300 is based on the R500 generation). So the offical drivers for it were relegated to legacy in 2009 with AMD's Catalyst 9.3 release & are no longer supported. Pretty crappy considering the HD 2300 was only on the market from 2007.
    To use the official catalyst drivers would require xorg 1.5.3 and kernel 2.6.29..... with no support for newer distros.
    Using open source drivers, cannot remember all the packages but have listed some below in case it helps anyone:-
    xf86-video-ati
    ati-dri
    lib32-ati-dri
    libtxc_dxtn
    lib32-libtxc_dxtn
    mesa
    lib32-mesa
    No xorg.conf needed for it using kms, but can make a config file to tweak if you like in the xorg.conf.d directory called 20-radeon.conf
    Last edited by Nixie (2012-12-24 17:21:29)

    Thanks for the response. It is not an obvious hardware issue. I would contact HP phone support to get the hardware addressed. You can utilize this website to learn how to contact HP appropriately, based on your region: Contact HP Worldwide
    Please let me know if you have any other questions or concerns. Thanks!
    Mario
    I worked on behalf of HP.

Maybe you are looking for

  • Complex JDOQL expression does not work. Or maybe I'm doing something stupid?

    Hi! I have several related objects: Customer, Contract and AccessKey. Each Customer has 1-to-many relationship with Contracts (so it can have several contracts) and each Contract has 1-to-many relationship with AccessKeys (so that contract can have s

  • My name appears with numbers in another user

    Hi I connected my Spotify account to Facebook and I have problem now with an user. My name appears with numbers in his account. I think that problem is because i had blocked this user in my Facebook :(Can you solve this please? I can´t speak with thi

  • Mac broke while trying to install Mountain Lion

    Well installing Mountain Lion turned out to be a disaster for me. After downloading the installer and opening it, the Macbook restarted and went into the installer program. After waiting for about 10 minutes it told me the disk needed to be repaired.

  • Trying to use a Microsoft C/C++ Header in LabWindows/CVI, will not work?

    Is there a way to get Microsoft based Header(s) files to compile in LabWIndows/CVI.  It appears that LabWindows/CVI does not like the words "BOOLEAN" or "HANDLE" in the header file for an example? Is there a switch that I need to set in LabWindows EN

  • Still can't connect to Exchange Calendar

    Problem started in Mavericks... My uni offers student email through Office365, it includes the calendar which works on every platform but the MacOS. (iOS, Outlook online, Android, etc.) The problem is that Calendar can't connect to the Exchange calen