Can not see the new appending fields in RSA6

Hi,
I add one appending structure to existing datasource, after that I can not see the new field in RSA6, RSO2. However I can see it from RSA2 and SE11 (for extract structure).
Any idea?
Thanks
Victor

Victor,
can you tell me how u have done this. you have a DS in RSA6 created from RSO2. then you created a append structure right? then click on your DS on the RSA6 screen. click on change icon on the application tool bar or function key CTRL + SHIFT +F1, maintain the datasource.
can you able to see the fields here or not (i'm asking for change mode)?
Nagesh.

Similar Messages

After partition using fdisk, i can not see the new device file (/dev/sdd1)

I used fdisk -l to partition /dev/sdd, use the entire disk as partition 1. it looks successful:
# fdisk -l /dev/sdd
Disk /dev/sdd: 10.7 GB, 10737418240 bytes
64 heads, 32 sectors/track, 10240 cylinders
Units = cylinders of 2048 * 512 = 1048576 bytes
Sector size (logical/physical): 512 bytes / 512 bytes
I/O size (minimum/optimal): 512 bytes / 512 bytes
Disk identifier: 0x35e3e2c4
Device Boot Start End Blocks Id System
/dev/sdd1 1 10240 10485744 83 Linux
the problem: i don't see the device file /dev/sdd1. tried to delete it and partition again, the same.
also tried
- mknod b 8 70 /dev/sdd1, to manually create it, but when i use oracleasm createdisk DISK2 /dev/sdd1, the command won't recognize manually crated /dev/sdd1.
- reboot the server,
- "partprobe" command, no luck.
in addition, cat /proc/partitions seems including /dev/sdd1:
cat /proc/partitions
major minor #blocks name
8 16 292935982 sdb
8 0 143338560 sda
8 1 512000 sda1
8 2 142825472 sda2
252 0 25608192 dm-0
252 1 25608192 dm-1
252 2 62423040 dm-2
252 3 35012608 dm-3
252 4 20480000 dm-4
252 5 10240000 dm-5
252 6 4096000 dm-6
8 32 10485760 sdc
8 33 10484736 sdc1
8 48 20971520 sdd
8 49 20971504 sdd1
8 64 10485760 sde
8 65 10485744 sde1
any advice?
Thanks as alwasy!
Edited by: 943714 on Apr 25, 2013 10:55 AM

After you create a new partition, always verify it:
# fdisk -l /path/to/diskOnce that confirms the new partition, you must tell the kernel to re-read the partition table. Several ways to do this, depending on what your storage connection is. This often works:
# partprobe /path/to/mydiskThen check if the kernel sees the partition:
# grep /proc/partitions mydiskIf it does, you are done.

I purchased an audio CD that I then imported into iTunes - I can find (and play) the new music from iTunes - however when I try and load it on my phone I can not see the new album as one that I can select in the music listings available for download.

It seems that recent additions to my iTunes library are not available for download to my (or my son's) iphone - other albums by the same artist are available.
Any help is appreciated...

Audiobooks (and ringtones) are currently a one-time only download from the store. If you don't have it on a backup of your downloads then you can try contacting iTunes support and see if they will grant you a re-download : http://www.apple.com/support/itunes/contact/ - click on Contact iTunes Store Support on the right-hand side of the page, then Purchases, Billing & Redemption

Can not see the menu of New Business Components Package in jdeveloper

I am just follow the developer guide.
and when I create the Business Components Package, the guide said that
========================================
In the JDeveloper Navigator, select the OA Project where you want to create your package.
From the main menu, choose File > New to open the New Object Gallery.
In the Categories tree, expand the Business Tier node, and select Business Components (BC4J).
In the Items list, select Business Components Package to open the Business Components Package Wizard. You can also right-click on the OA Project and select New Business Components Package to navigate directly to the Business Components Package Wizard.
=====================================
In fact I can not see the menu about Business Components (BC4J) in the File/new/buisness tier/Business Components (BC4J).
I can only see the File/new/buisness tier/ADF Business Components.
And can not find the "Business Components Package" under ADF Business Components either.
I am using the JDev Extension for OA (p5856648_R12_GENERIC.zip) and EBS 12.0.0.
And I create an OA Workspace and OA Project.
can anyone help?

James,
Use search facility on forum. Chk thread Re: OAF Toolbox Tutorial Help - Search
--Shiv

When I have video clips on my timeline, they do not play in the monitor screen. I hear the sound track but can not see the image. To test if my new files are somehow the problem, I went back and used video files that I used successfully a year ago, and th

When I have video clips on my timeline, they do not play in the monitor screen. I hear the sound track but can not see the image. To test if my new files are somehow the problem, I went back and used video files that I used successfully a year ago, and they no longer play in the monitor window. I hear the sound track, but do not see any video. Have I changed some setting that controls video playback in the monitor window?

Randy Ruttger
Thanks for the follow up.
Missing in this equation were the version of Premiere Elements that you were using and the computer operating system on which it was running. But...
The deed is done. But.....Until now and after you went ahead and moved to version 12, we now learn what version of Premiere Elements you were using. We still do not know the computer operating system involved.
You just said Premiere Elements 10. Premiere Elements 10 is hit by a serious known display issue if the computer uses a NVIDIA GeForce video card/graphics card. In this issue, the only remedy is to roll back the driver version to about May 2013. The description of the problem and how to do the roll back are described in one of the Announcements at the top of this forum. What video card/graphics card does your computer use?
On another front, Adobe will be releasing a new version of Premiere Elements any day now. No one but Adobe knows the feature set for the new version. That type of information is announced at the moment of release of the new version.
So the remedy to the problem that you presented in this thread could have been...
1. Rolling back the NVIDIA GeForce driver version to about May 2013 if possible (Windows 8 or 8.1 64 bit, may not be possible)
2. Move to another version of Premiere Elements (which you did)
I offer the above for consideration so that you can review your decisions. We are pleased to learn that Premiere Elements 12/12.1 works for you.
Please do not hesitate to ask questions and ask for clarifications, but remember that the answers are in the details.
Best wishes,
ATR

My iMac does not see the new Toshiba external drive in Finder or Disk Utility. How can I get it to see the drive?

My iMac does not see the new Toshiba external drive in Finder or Disk Utility. How can I get it to see the drive?

From the menu bar, select
 ▹ System Preferences ▹ Energy Saver ▹ Power Adapter
and uncheck the box labeled Put the hard disk(s) to sleep when possible, if it's checked.
If the drive has more than one interface (USB, FireWire, Thunderbolt, eSATA), try one of the other interfaces.
Check that the data cable is securely inserted at both ends.
Try a different cable.
If you're connecting the drive through a hub, connect it directly to a built-in port on the Mac.
If you're connecting it directly, try a different port.
Disconnect all other devices on the bus, or as many as possible.
Test the drive with another Mac. Test another drive with this Mac.
If the drive is bus-powered, but has an AC adapter, connect the adapter.
Start up in Recovery mode and launch Disk Utility. Is the drive recognized?
Start up in Safe Mode and test.
Reset the NVRAM.
Reset the System Management Controller.
If the drive doesn't work under any of the above conditions, and if another drive does work with the same Mac, then the drive is malfunctioning.

Brand New RD240 ThinkServer can not see the LSI 8708EM2 RAID Controller During Bootup

I have a brand new out the box RD240 ThinkServer that can not see the LSI 8708EM2 RAD Controller it came with. This RAID controller simply does not want to function. This RAID Cntroller does not show up during the boot up and I even tried putting in a different slot in the riser card, thinkn maybe it was a bad PCI-e slot, but made no difference. Also the Lenovo Easy Setup software does not find this controller either. So I'm wondering if there is an issue with the RAID Controller or is it a bad Riser card? Does anyone have any idea's on what can be done or what I may be missing?

For a list of Warranty Support contact numbers, please visit:
http://support.lenovo.com/en_US/feedback/detail.page?LegacyDocID=MIGR-76613
In the U.S. you can call: 1-800-426-7378

Jambox had no problem to connect with iPhone 4 S but my new iphone 6 can not see the jambox. Any solution known?

I used my jambox with the iPhone4S via bluetooth without problems. Now i changed to the new iPhone 6 and the new phone can not see the jambox. Is that known and what solution is available?

Hey rjdit,
Thanks for the question. After reviewing your post, it sounds like you are having trouble connecting to 3rd party devices. I would recommend that you read these articles, they may be able to help you resolve or isolate the issue.
iOS: Troubleshooting Bluetooth connections
iOS: Third-party Bluetooth accessories
Thanks for using Apple Support Communities.
Have a nice day,
Mario

Can not see the data in the grid

Hi,
nice to see the new features, but I can not see the the table inserts
in the data grid - the <data> rider is not clickable.
Regards

Hi annerose,
This problem has appeared in a few other threads. It's caused by installing Release 2 Raptor over Release 1 Raptor without first deinstalling Release 1 Raptor . So what you need to do is:
1) Back up any important Raptor files, e.g. connections etc.
2) Remove the existing Raptor Rel 1 installation folder
3) Install Raptor Rel 2
Hope this helps
ady

I bought an I pad 2 from us but I can not activate the Facetime in UAE(Dubai)as I can not see the country in the I pad's drop list, anyone has an idea as how to resolve this issue

I bought an I pad 2 from us but I can not activate the Facetime in UAE(Dubai)as I can not see the country in the I pad's drop list, anyone has an idea as to how to resolve this issue

I'm not that familiar with how FaceTime works. I know how to set It up but I don't use it. I just know that you can't activate in the UAE. I believe that you can activate in any country that permits it's use. Whether you will need a new ID or not, I can't confirm.
You can Google this and get all sorts of articles on workarounds. Apparently if you set up a VPN you can use it in the UAE. Here is one article that I found.
http://talkfree7.blogspot.com/2010/09/how-to-facetime-voip-call-from-uae.html
I Googled "workaround for FaceTime in UAE" to find this.

Can not see the report in report manager/admin tab

Hi,
in 8.49 on Win 2003 some users can not see the reports in report manager/admin tab. PS user can see them.
Should we add some grants in user profile ? Which ? Any query to compare that user profile with PS ?
Thank you.

On the administration page, you will be able to see "View Reports For" header on the top.
Under that header you will see the following fields:
User ID/Type/Last/Status/Folder /Instance
Above values will be used by PeopleSoft to filter and display the list of reports
If the user has selected Status as Processing and saved the page, PeopleSoft will only show reports which are in Processing status.
If user runs a report and it has been posted, it will not show up in report manager coz the filter value is set to Processing.
Hope this helps. I dont think Permissions has anything to do with this since user is able to view the page.

Can not see the device net Master Interface in my project.

Can not see the device net Master Interface in my existing project. Need to Modify exististing code. Can not recomiple and create exe file after making changes. Error says the vi's are broken. Tried re-installing industrial communications for device net but get an error saying a newer version is already installed. Do I need to plug my computer into the device net scanner to fix this?

Assume the installation disk is an OS X disk? If it's the original one that came with the system (grey-colored disk versus black retail disk) have you tried to hold the alt key down when you boot? This would allow you to choose the Apple hardware test. If you can do this, choose the Apple hardware test, click the arrow to the right, and when prompted choose the extended test. Does that give you any errors or messages about a hardware problem?
Are you able to hold the C key down when you reboot, to boot off the installation disk?

In Firefox can not see the Downloads window, in the jump in the boot to be seen - the download speed Downloaded much and now can not see how to fix it?

in Firefox can not see the Downloads window, in the jump in the boot to be seen - the download speed
Downloaded much and now can not see how to fix it?

I hate the new downloads-in-a-tab scheme. This was an unnecessary change in my book (if it aint broke, don't "fix it").
So in order to get it back, I performed the about:config browser.download.useToolkitUI change, but now all I get is a blank download window that pops up every time I download something.
Is there something else that I need to do? I've checked the change and it was saved, but it didn't resolve my issue as much as it just caused me a new issue.

Can not see the option Execution with Data Change in the infoprovider?

Hi team,
i am using query designer 3.x, when i go into my bex brodcaster settings and schedule my report
i can not see the option "Execution with Data Change in the infoprovider",
i can only see 2 options
Direct scheduling in background process
create new scheduling
periodic,
is there any setting which i would be able to see the option "Execution with Data Change in the infoprovider"?
kindly assist

Hi Blusky ,
check the below given link.
http://help.sap.com/saphelp_nw04/Helpdata/EN/ec/0d0e405c538f5ce10000000a155106/frameset.htm
Regards,
Rohit Garg

Why i can not see the columns of "Tax Category" in transaction code FS00

Dear Experts,
Why i can not see the columns of "Tax Category" and "Posting without tax allowed" in tab of "Control Data" transaction code FS00?
How can i add the columns of "Tax Category" and "Posting without tax allowed"?
Looking forward to your reply.
Best Regards,
Merry

Hi,
Go to transaction OBD4, and check whether the field "Tax category" is suppressed in group "Account control" for your GL account group.
If not, then go to OB26 and check the field status for the same field for create, change activity.
Regards,
Gaurav

Can not see the new appending fields in RSA6

Similar Messages

Maybe you are looking for