Can not stay connected to Airport express

I have an airport exress that is less then 9 months old.  I have my internet provide wirlessely so my macbook pro picks up the signal and i share it with the airport exress.  With the AE set to bridge mode.  This was all working fine for the last 3 months, but now for some reason I can not stay connected with any of my devices wirelessly with the AE.  I try to connect with my Iphone 4s and when i click on the network to connect i never recieve a check mark on the left all it does is give me the moving circle.  I try to search the web on the phone and it will work for a second then not work for who know how long then work for a second ect.... i have hard rebooted the AE, reset network settings in my phone, reset smc and pram.  when i access the ae through airport utility on my mac the internet shows green and the AE show amber becuase it says it does not have a valid ip address.  I access the AE from my phone and the AE shows the same and the internet will go from green to amber and back.  Also it will not stay connected to the AE i try to change setting on the AE through my phone and as long as i do it quickly it works fine, but if i wait anylonger then 10-30 seconds the phone drops the AE and i have to start over even though it will pick it up again with in  a second or two.  this is the same for ipad, three iphones, dell computer, and a android phone. 

Simply reconfigure your Airport Express to either use for airtunes only or to extend the range of the existing network. This effectively connects the Airport Express to your main wireless router as a basic access node rather than a separate router creating its own network.
If you consult the User Guide that came with your Airport Express you'll find additional information on how to setup an Express to simply extend a local wireless network rather than function independently.
Why reward points?(Quoted from Discussions Terms of Use.)
The reward system helps to increase community participation. When a community member gives you (or another member) a reward for providing helpful advice or a solution to their question, your accumulated points will increase your status level within the community.
Members may reward you with 5 points if they deem that your reply is helpful and 10 points if you post a solution to their issue. Likewise, when you mark a reply as Helpful or Solved in your own created topic, you will be awarding the respondent with the same point values.

Similar Messages

  • Itunes will not stay connected to Airport Express with any Yosemite update.

    Since installing Yosemite (original and updates) my itunes will no longer stay connected to Airport Express on my iMac. Any ideas?
    I have no probblem at all when using ipad or other devices.
    Matt

    Hello mtvessell,
    If you are having issues connecting to the iTunes Store, then start with the article below for some general troubleshooting to get it sorted out. If it continues, then take a look at the second article for additional support. 
    Can't connect to the iTunes Store
    http://support.apple.com/en-us/TS1368
    iTunes: Advanced iTunes Store troubleshooting
    http://support.apple.com/en-us/TS3297
    Regards,
    -Norm G.  

  • G5 & PC NOT STAYING CONNECTED VIA AIRPORT EXPRESS!

    I've got a G5 and a PC - Hoped that Airport Express would allow both to access internet (via cable modem).
    The connection drops after a little while. Everything says its working but obviously it's not.
    ANY HELP??!!!
    Thx!

    reinis wrote:
    I have white Macbook (802.11g capable) and Airport Express (802.11g capable).
    I have a LAN internet connection, which is pretty fast. When I connect the cable to my ethernet and try to download something (for instance, speedtest.net) then the download speed is 33Mbit/sec, and upload is 20Mbit/sec.
    I also have an Airport Express router - the 802.11g to be specific. So in the Airport Utility, under Wireless I selected "802.11g ONLY" and selected 24Mbit/sec Multicast rate.
    When I tried to download something when conected to my Airport Express router - what actually happened, is that my computer is 2 m away from the Airport Express and the max download speed approximately should be ~24 Mbit/sec, but it turns out that the down speed is ONLY 14 Mbit/sec and the upload speed is 11 Mbit/sec.
    So it means, that the Airport Express actually cannot deliver the 24 Mbit/speed.
    I am actually pretty dissapointed, because I was kind of okay with the fact that I will loose those ~10 Mbit/sec from my actual internet sped when connected via Airport express, but I did not expect that it would be halved.
    Any solutions?
    According to one source, the maximum throughput of 802.11g is 25 Mbps. That assumes ideal conditions. To learn more about those conditions in your case, launch AirPort Utility, double-click on your AirPort station to enter "Manual Setup" mode, select the "Advanced" panel, click on the "Logs and Statistics" button, then click on the "Wireless Clients" tab. There you will see values for signal and noise. The closer those two numbers are together, the worse throughput you can expect.
    If the value for noise is high, you might try setting your AirPort unit to a different channel.
    All the above is based on your having no other Wi-Fi equipment.

  • PowerBooks will not automatically connect to Airport Express

    Recently purchased iPhone and changed my Airport Express password to something easier to spell on iPhone keyboard. Since then, two PowerBooks I own (early G4 and later G4) will not automatically connect to Airport Express Network. I have to manually go to Airport icon in menu bar and join network. Any advice on this small annoyance is greatly appreciated.

    Went to the Sys Pref and edited the profile of the AE. Now loads fine.

  • Airport Utility can not see my 2 airport express.

    It does see my airport extreme but it has stopped seeing the 2 express stations.  I have had this set up for years and play iTunes to stereo systems in 2 different rooms in the house.  But it just crashed and lost the connections to all three base stations.  I have been able to reset the Airport Extreme but Airport utility now will not find the 2 Airport Express units that I have.  These units are 802.11g capatible.

    I have been able to reset the Airport Extreme but Airport utility now will not find the 2 Airport Express units that I have.
    Suggest that you perform a Factory Default Reset on each AirPort Express (AX) and then reconfigure them to "join" the wireless network that is being provided by the AirPort Extreme.
    Power down the AX for a moment
    Hold in the reset button and keep holding the reset button in while you plug the AX back in to power
    Release the reset button 8-10 seconds after you plug the AX in to power
    Allow 40-45 seconds for the AX to restart back to a slow, blinking amber light
    At this point, the AX is providing a wireless signal with a name like Apple Network xxxxxx. You must log on and connect to this network (no password is required) first, then open AirPort Utility, select the AX and click Continue to follow the guided setup.
    You also have the option of configuring using Ethernet by temporarily connecting an Ethernet cable from your PC to the AirPort Express if you do not want to configure it using wireless.

  • HT4061 my memory is low on my ipad and i can not stay connected to the internet.  How do I fix this problem

    My ipad will not stay connected to the internet.  the message in the settings says low memory. How do I fix this problem?

    Go to Settings > General > Usage and you will see the memory consumers.  Remove some of the big stuff.

  • ITunes not playing/connecting through Airport Express

    Whenever I try to play a track in iTunes wirelessly through my Airport express iTunes always returns the error: "An error occured while connecting to the remote speaker "AirPort Express" The network connection failed".
    I can't work out what's wrong because the Airport light is green and connected to my router perfectly, there are no errors in the Airport utility and I can print wirelessly to the printer connected to the Airport using the Bonjour setup.
    I have Windows 7 and the latest versions of all software and firmware installed. Turning off Windows firewall makes no difference so it can't be that. I have tried everything I can possibly think of and have gottem nowhere. Please help!

    Darryl Rehr wrote:
    I have configured and re-configured my Airport Express, but I can't get it to receive music from iTunes.
    iTunes does recognize presence of Airport Express (named "Stereo Cabinet").
    However, when I select "Stereo Cabinet" in the pulldown menu, all I get is reduced volume output through my computer speakers... not through the stereo system hooked up the to the Airport Express.
    I've had this problem for months... posted here some time ago, but got no response.
    I am running 10.6.2 on an Intel Core duo Macbook laptop. This function used to work just fine, and I can't figure out why it no longer does. I think I had the same trouble under 10.5... but my attempts to figure it out were only sporadic (busy life, you know?).
    Can anyone help?
    DR
    sorry if i ask the obvious but have you enabled airtunes like so ?

  • My wife and I share our Mac OS 10.6.8 since downloading Skype on her account she can not stay connected to any web site she pulls up. I removed Skype from here account but it stll happens. What can I do to clear this up?

    My wife and I share the same Mac OS 10.6.8 and since downloading Skype on her accout she came not asty connected to any web site for more than a few seconds. I have remove Skype from her account but not mine. I don't have the problem on my accout and I still have Skype loaded. How can I fix this problem?

    O.k. Thanks for the clarification. I poked around in my TimeCapsule router's settings (TimeCapsule is an Apple Airport Extreme router with attached hard drive for wireless backup/storage). Unfortunately, it doesn't look like I can disable multicasting with the TimeCapsule. I can change the multicasting 'rate'. Settings are Low, Medium, High. It's currently set to Low.
    I did a few web searches, and found an Apple.com article: <http://support.apple.com/kb/HT3789?viewlocale=en_US> which explained how to disable Bonjour Service Advertisements. I believe this is the same thing as 'Multicasting'. The process is a modification of "/System/Library/LaunchDaemons/com.apple.mDNSResponder.plist", and a restart of the Mac is required afterwards.
    I'm a bit concerned that disabling multicasting will interfere with my AppleTVs and iTunes music sharing, but I may try it next time I'm up for a computer workout. This task will require editing of system preference files, could require multiple restarts, might interfere with my AppleTVs, could interfere with my iTunes file sharing, doesn't have a documented relationship to my problem.
    This is way to difficult for something that should just work. Did you say you had read something about a relationship between this bonjour multicasting and smb connectivity? If it was online could you post the link?
    I'm currently able to connect to the drive using NFS, but I have to manually configure that connection each time I reboot (can't get the 'Disk Utility' configured to do it automatically). While it's working with NFS, it's not my preferred connect method (for various reasons).

  • Can no longer connect to Airport Express with upgrade to iTunes 10.1

    Since I upgraded to iTunes 10.1 I can no longer connect to my Airport Express (unknown error-15000). Another computer on my betwork running an older version of iTunes still works on the Airport Express.
    Any ideas? I have tried to uninstall and reinstall airport express with no success.

    Rather than disabling the firewall, try making sure you've got exceptions in it for BonJour. Although the following document is about a different error message, the instructions in there are worth trying. (At step 7, make sure there's an exception for BonJour as well.)
    [iTunes for Windows: Bonjour alert due to firewall, security, or proxy software|http://support.apple.com/kb/TS3448]

  • Having iTunes volume only affect Mac speakers, not those connected with Airport Express

    In iTunes Help, it says "To use only the volume controls on your remote speakers, see Adjust the sound quality." Great! At Adjust the sound quality, it says "You can customize the sound for...specific speakers." Also great! But...
    How do I do that? There doesn't seem to be any instructions on how to actually accomplish this thing iTunes Help is claiming I can do, namely to be able to change the main iTunes volume (through any of several methods) and have that not affect the speakers I have hooked up through my Airport Express.
    I'm well aware I can do this by switching to iTunes, clicking on the Zoom button if I've got iTunes minimized, clicking on the little "speaker" icon (though how that looks like a speaker I'm not sure), choosing "multiple speakers," and dragging the "Computer" slider. OR, if I can figure out how to make iTunes do what the help linked above claims I can, I can just use my Synergy hotkeys to change the volume with a tap on my keyboard.

    I'm also suffering from skipping/sped up music, only when streaming certain internet radio stations to my Express (for example, friskyRadio in the electronica section). Mine's setup not to distribute IP addresses, if that's relevant.
    Other than installing iTunes version 7 (now at 7.0.1) nothing has changed on my network, or on my computer.

  • My computer can not find my new airport express?

    I have my airport express connected via the ethernet, downloaded the utility folder but the light continues to flash amber and when I open the airprot utility it cannot find the airport. It is plugged in and right beside me so it is not a range issue. I have never had problems with past airports. Is it faulty?
    Thanks

    Hey twiprere,
    The following article outlines how to reset an AirPort base station, doing so may resolve your issue:
    Resetting an AirPort Base Station or Time Capsule FAQ
    http://support.apple.com/kb/ht3728
    Thanks,
    Matt M.

  • I can't print wirelessly using Airport Express.  I have my HP printer connected to a USB hub, and the hub to the Airport Express, but when I select the HP from the printer list, my MacBook says the printer is "off-line" - even when it is not.

    I can't print wirelessly using Airport Express.  I have my HP printer connected to a USB hub, and the hub to the Airport Express, but when I select the HP from the printer list, my MacBook says the printer is "off-line" - even when it is not.  I've tried several USB connectors, and several different ports on my USB hub; same result.  I need to have the HP connected to the hub 'cause from there it's connected to our desktop Mac.

    Hi,
    I am currently replying to this as it shows in the iChat Community.
    I have asked the Hosts to move it to Snow Leopard  (you should not lose contact with it through any email links you get)
    I also don't do Wirelss printing so I can't actaully help either.
    10:01 PM      Friday; July 29, 2011
    Please, if posting Logs, do not post any Log info after the line "Binary Images for iChat"
     G4/1GhzDual MDD (Leopard 10.5.8)
     MacBookPro 2Gb( 10.6.8)
     Mac OS X (10.6.8),
    "Limit the Logs to the Bits above Binary Images."  No, Seriously

  • I need to connect an Airport Express to an exisitng Wi-Fi Netgear Router. 1) My PC do not detect the Airport Express, 2) AE is flashing amber all the time... Please if someone can help?

    I need to connect an Airport Express to an exisitng Wi-Fi Netgear Router. 1) My PC do not detect the Airport Express, 2) AE is flashing amber all the time... Please if someone can help?

    Before I bought it I did the same question at the Apple Store, and they told me "You can extend your existing Wi-Fi Signal with Airport Express wireless...
    You cannot extend wireless from any brand except another apple router.. the store might have assumed you were using an apple main router. Most people who buy express buy them to extend an extreme or time capsule.
    You are correct .. in the setup documents it does say 5.6.1 is adequate to do the setup.. my bad.. !!

  • Airport express will not stay connected

    I have a new Airport Express (802.11n) and it will not stay connected to my MacBook Pro. Any suggestions?

    I have returned the Express and reinstalled my Extreme. I found a "tip" page that suggested to put a sheet of aluminum foil behind the Express to concetrate the signal inside the house. This crude idea has not solved the problem. My MacPro is a 2 GHz Intel Core i7. Any further suggestions?

  • Is there a way I can connect my airport express to be able to airplay the sound from my apple tv?

    Is there a way I can connect my airport express to ba able to air play to my speakers the audio from apple tv?

    GEESAR wrote:
    hi there
    is there anyway i can use the unlimited data i have from my mobile network provider (o2)  on this i pod touch 4 generation the latest model  NO.
    and does the sim from my mobile network o2 be used in the ipod touch4 to use the unlimited minuites i have from my mobile network provider  NO
    if not then how do i use the unlimited data ive been given through my mobile network provider please tell me most kindly  Purchase a mobile WiFi hotspot (Sometimes referred to as a MyFi), or have that service added to your cell phone.
       geeeeesar also how does this ipod touch4  pick up the  wifi free of charge is this possible or do you have to pay for limited data to access internet Your iPod can connect to any unsecured WiFi network that you are currently within range of.  These networks can be found at your local library, some city/county government buildings, doctor's offices, Denny's, IHOP, Starbuck's, Home Depot, Lowes, Best Buy, and other merchants.  Your iPod can connect to any secured WiFi network that you are within range of and that you have the password for. 
    thanks  can i pod touch 4 generation download movies too  please help thank u very much....  Yes.  If your iPod has a WiFi connection and you have an account with a service like NetFlix....

Maybe you are looking for

  • How to assign authorization objects to a cube

    Hello, My cube includes 0profit_ctr which is marked as authorization relevant. Still in RSSM my cube is not included in the list of infocubes for an authorization object (zprofit) linked to 0profit_ctr. I'm therefore not able to enable that authoriza

  • Scared to download new version "Yosemite" I heard it does not work well on older versions like 10.7.5

    I am worried about downloading the latest version of yosemite on my macbook pro "10.7.5" for the reason that downloading the latest version for iphones actually killed my phone. IT would not turn off anymore and the battery died in about 3 hrs even w

  • Setting Character Limits or Font Size in Text Fields In Forms

    Hi everyone.  I've created a form but the problem is that people are changing the font size in order to fit mrore into the locked text fields.  I want to create either a chaacter limit or lock the font size as to prevent people from changing around t

  • Is there a firmware upgrade to take USB 1.1 to USB 2 to run Egalato Video Capture

    We are running OS version 10.5.8 7 are using Elagato vidoe capture software.  The USB requirements are USB 2.0 however our USB port is USB 1.1.  We have all the required Apple software upddates.  Does anyone know of a how to upgrade the USB ports fro

  • Trips for drop-ship SO

    Hello, I would like to get an opinion whether it is possible (within standard OM functionalities), to plan a trip for drop-shipped SO. I can see that I can have trip only for the delivery, and delivery can be created only for released SO, I cannot do